control flow doet nog niks
Dependencies: Encoder HIDScope MODSERIAL mbed
main.cpp
- Committer:
- Zeekat
- Date:
- 2015-10-09
- Revision:
- 2:2563df4ee829
- Parent:
- 1:2f23368e8638
- Child:
- 3:7273bbe6aa02
File content as of revision 2:2563df4ee829:
#include "mbed.h" #include "MODSERIAL.h" #include "encoder.h" #include "HIDScope.h" Serial pc(USBTX,USBRX); HIDScope scope(2); // definieerd het aantal kanalen van de scope // Define Tickers and control frequencies Ticker controller1, controller2; // definieer de ticker die controler1 doet // Go flag variables volatile bool motor1_go = false, motor2_go = false; // Frequency control double controlfreq = 50 ; // controlloops frequentie (Hz) double controlstep = 1/controlfreq; // timestep derived from controlfreq //MOTOR OUTPUTPINS // motor 1 PwmOut motor1_aan(D6); // PWM signaal motor 2 (uit sheets) DigitalOut motor1_rich(D7); // digitaal signaal voor richting // motor 2 PwmOut motor2_aan(D5); DigitalOut motor2_rich(D4); // ENCODER INPUTPINS Encoder motor1_enc(D12,D11); // encoder outputpins Encoder motor2_enc(D10,D9); int reference1 = 0; // set the reference position of the encoders int reference2 = 0; // EXTRA INPUTS AND REQUIRED VARIABLES //POTMETERS AnalogIn potright(A0); // define the potmeter outputpins AnalogIn potleft(A1); // RESETBUTTON DigitalIn button(PTA4); // defines the button used for a encoder reset int button_pressed = 0; // SETPOINT SETTINGS // define storage variables for setpoint values double c_setpoint1 = 0; double c_setpoint2 = 0; // define the maximum rate of change for the setpoint (velocity) double Vmax = 5; // rad/sec // CONTROLLER SETTINGS // motor 1 const double m1_Kp = 1; // Proportional constant const double m1_Ki = 1; // integration constant const double m1_Kd = 0; // differentiation constant // motor 2 const double m2_Kp = 1; const double m2_Ki = 0; const double m2_Kd = 0; // storage variables // motor 1 double m1_err_int = 0; double m1_prev_err = 0; // motor 2 double m2_err_int = 0; double m2_prev_err = 0; //// FILTER VARIABLES // storage variables // differential action filter, same is used for both controllers double m_f_v1 = 0; double m_f_v2 = 0; // Filter coefficients // differential action filter const double m_f_a1 = 1.0, m_f_a2 = 2.0, m_f_b0 = 1.0, m_f_b1 = 3.0, m_f_b2 = 4.0; // coefficients from sheets are used as first test. //////////////////////////////////////////////////////////////// /////////////////// START OF SIDE FUNCTIONS //////////////////// ////////////////////////////////////////////////////////////// // these functions are tailored to perform 1 specific function // counts 2 radians // this function takes counts from the encoder and converts it to the amount of radians from the zero position. // It has been set up for standard 2X DECODING!!!!!! double get_radians(double counts) { double pi = 3.14159265359; double radians = (counts/4200)*2*pi; // 2X DECODING!!!!! ((32 counts/rotation, extra warning) return radians; } // This functions takes a 0->1 input converts it to -1->1 and uses passing by reference (&c_setpoint) // to create a reference that moves with a variable speed. It is now set up for potmeter values. double setpoint_f(double input, double &c_setpoint) { double offset = 0.5, gain = 2; double potset = (input-offset)*gain; if(potset < 0.1 && potset > -0.1) { potset = 0; } double setpoint = c_setpoint + potset * controlstep * Vmax ; c_setpoint = setpoint; return setpoint; } // This function takes the controller inputvalue and ensures it is between -1 and 1 // this is done to limit the motor input to possible values (the motor takes 0 to 1 and the sign changes the direction). // I am aware it has unnecesary steps but it works. double outputlimiter (double output, double limit) { if(output> limit) { output = 1; } else if(output < limit && output > 0) { output = output; } else if(output > -limit && output < 0) { output = output; } else if(output < -limit) { (output = -1); } return output; } // BIQUADFILTER CODE GIVEN IN SHEETS // used for d-control double biquadfilter(double u, double &v1, double &v2, const double a1, const double a2, const double b0, const double b1, const double b2) { double v = u- a1*v1-a2*v2; double y = b0*v+b1*v1+b2*v2; v2 = v1; v1 = v; return y; } // PID Controller given in sheets // aangepast om zelfde filter te gebruiken en om de termen later gesplitst te kunnen limiteren (windup preventie!!) double PID(double e, const double Kp, const double Ki, const double Kd, double Ts,double &e_int, double &e_prev) { // Proportional double P = Kp * e; pc.printf("P = %f ",P); // Derivative double e_derr = (e - e_prev)/Ts; pc.printf("D-actie %f",e_derr); // e_derr = biquadfilter(e_derr, m_f_v1, m_f_v2, m_f_a1, m_f_a2, m_f_b0, m_f_b1, m_f_b2); e_prev = e; // double D = Kd* e_derr; // Integral e_int = e_int + Ts * e; double I = e_int * Ki; // PID double output = P + I ;// + D; return output; } // this function is a simple K control called by the motor function double K_control(double error,double K) { double output = K*error; // controller output K*e output = outputlimiter(output,1); // limit the output to -1->1 return output; } ///////////////////////////////////////////////////////////////////// ////////////////// PRIMARY CONTROL FUNCTIONS /////////////////////// /////////////////////////////////////////////////////////////////// // these functions are used to control all aspects of a single electric motor and are called by the main function // MOTOR 1 void motor1_control() { double setpoint1 = setpoint_f(potright.read(), c_setpoint1); // determine the setpoint that has been set by the inputsignal double rads1 = get_radians(motor1_enc.getPosition()); // determine the position of the motor double error1 = (setpoint1 - rads1); // determine the error (reference - position) scope.set(0,setpoint1); // disabled because HIDScope is acting strangely scope.set(1,rads1); scope.send(); // double output1 = K_control(error1, m1_Kp); // bereken de controller output voor motor 1(zie hierboven) double output1 = PID(error1, m1_Kp, m1_Ki, m1_Kd, controlstep, m1_err_int, m1_prev_err); pc.printf("output 1 %f \n",output1); // ws best locatie om output te blokkeren als grenzen bereikt zijn, simpel if-loopje met rad1 if(output1 > 0) { // uses the calculated output to determine the direction of the motor motor1_rich.write(0); motor1_aan.write(output1); } else if(output1 < 0) { motor1_rich.write(1); motor1_aan.write(abs(output1)); } } // MOTOR 2 void motor2_control() { double setpoint2 = setpoint_f(potleft.read(), c_setpoint2); // determine the setpoint that has been set by the inputsignal double rads2 = get_radians(motor2_enc.getPosition()); // determine the position of the motor double error2 = (setpoint2 - rads2); // determine the error (reference - position) // scope.set(3,setpoint2); // disabled because HIDScope is acting strangely // scope.set(4,rads2); // scope.send(); // double output2 = K_control(error2, m2_Kp); // bereken de controller output voor motor 1(zie hierboven) double output2 = PID(error2, m2_Kp, m2_Ki, m2_Kd, controlstep, m2_err_int, m2_prev_err); if(output2 > 0) { // uses the calculated output to determine the direction of the motor motor2_rich.write(0); motor2_aan.write(output2); } else if(output2 < 0) { motor2_rich.write(1); motor2_aan.write(abs(output2)); } } ////////////////////////////////////////////////////////////////// //////////// DEFINE GO-FLAG FUNCTIONS /////////////////////////// //////////////////////////////////////////////////////////////// void motor1_activate() { motor1_go = true; } void motor2_activate() { motor2_go = true; } int main() { pc.baud(115200); // Ticker calling the primary functions. If neccessary use the ticker to change bools and execute in the main loop as shown in the sheets. controller1.attach(&motor1_activate, controlstep); controller2.attach(&motor2_activate, controlstep); while(true) { if(motor1_go) { motor1_go = false; motor1_control(); } if(motor2_go) { motor2_go = false; motor2_control(); } if(button.read() == button_pressed) // reset the encoder to reference position { motor1_enc.setPosition(reference1); motor2_enc.setPosition(reference2); } } }