#include <sx1276-mbed-hal.h>

Inherits SX1276.

Public Member Functions
virtual uint8_t	DetectBoardType (void)
	Detect the board connected by reading the value of the antenna switch pin.
virtual bool	CheckRfFrequency (uint32_t frequency)
	Checks if the given RF frequency is supported by the hardware.
virtual void	Write (uint8_t addr, uint8_t data)
	Writes the radio register at the specified address.
virtual uint8_t	Read (uint8_t addr)
	Reads the radio register at the specified address.
virtual void	Write (uint8_t addr, void *buffer, uint8_t size)
	Writes multiple radio registers starting at address.
virtual void	Read (uint8_t addr, void *buffer, uint8_t size)
	Reads multiple radio registers starting at address.
virtual void	WriteFifo (void *buffer, uint8_t size)
	Writes the buffer contents to the SX1276 FIFO.
virtual void	ReadFifo (void *buffer, uint8_t size)
	Reads the contents of the SX1276 FIFO.
virtual void	Reset (void)
	Reset the SX1276.
virtual void	SetRfTxPower (int8_t power)
	Sets the radio output power.
virtual bool	Init (RadioEvents_t *events)
	Return current radio status, returns true if a radios has been found.
virtual void	RadioRegistersInit (void)
	Initializes the radio registers.
virtual RadioState	GetStatus (void)
virtual void	SetModem (RadioModems_t modem)
	Configures the SX1276 with the given modem.
virtual void	SetChannel (uint32_t freq)
	Sets the channel frequency.
virtual bool	IsChannelFree (RadioModems_t modem, uint32_t freq, int16_t rssiThresh)
	Sets the channels configuration.
virtual uint32_t	Random (void)
	Generates a 32 bits random value based on the RSSI readings.
virtual void	SetRxConfig (RadioModems_t modem, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint32_t bandwidthAfc, uint16_t preambleLen, uint16_t symbTimeout, bool fixLen, uint8_t payloadLen, bool crcOn, bool freqHopOn, uint8_t hopPeriod, bool iqInverted, bool rxContinuous)
	Sets the reception parameters.
virtual void	SetTxConfig (RadioModems_t modem, int8_t power, uint32_t fdev, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint16_t preambleLen, bool fixLen, bool crcOn, bool freqHopOn, uint8_t hopPeriod, bool iqInverted, uint32_t timeout)
	Sets the transmission parameters.
virtual uint32_t	TimeOnAir (RadioModems_t modem, int16_t pktLen)
	Computes the packet time on air for the given payload.
virtual void	Send (void buffer, int16_t size, void header=NULL, int16_t hsize=0)
	Sends the buffer of size. Prepares the packet to be sent and sets the radio in transmission.
virtual void	Sleep (void)
	Sets the radio in sleep mode.
virtual void	Standby (void)
	Sets the radio in standby mode.
virtual void	StartCad (void)
	Sets the radio in CAD mode.
virtual void	Rx (uint32_t timeout)
	Sets the radio in reception mode for the given time.
virtual bool	RxSignalPending ()
	Check is radio receives a signal.
virtual void	Tx (uint32_t timeout)
	Sets the radio in transmission mode for the given time.
virtual void	SetTxContinuousWave (uint32_t freq, int8_t power, uint16_t time)
	Sets the radio in continuous wave transmission mode.
virtual int16_t	MaxMTUSize (RadioModems_t modem)
	Returns the maximal transfer unit for a given modem.
virtual int16_t	GetRssi (RadioModems_t modem)
	Reads the current RSSI value.
virtual int32_t	GetFrequencyError (RadioModems_t modem)
	Reads the current frequency error.
virtual void	SetMaxPayloadLength (RadioModems_t modem, uint8_t max)
	Sets the maximum payload length.
virtual void	SetPublicNetwork (bool enable)
	Sets the network to public or private. Updates the sync byte.
Static Public Attributes
static struct RadioRegisters	RadioRegsInit []
	Radio hardware registers initialization definition.
Protected Types
typedef void(SX1276::*	DioIrqHandler )(void)
Protected Member Functions
virtual void	IoInit (void)
	Initializes the radio I/Os pins interface.
virtual void	SpiInit (void)
	Initializes the radio SPI.
virtual void	IoIrqInit (DioIrqHandler *irqHandlers)
	Initializes DIO IRQ handlers.
virtual void	IoDeInit (void)
	De-initializes the radio I/Os pins interface.
virtual uint8_t	GetPaSelect (uint32_t channel)
	Gets the board PA selection configuration.
virtual void	SetAntSwLowPower (bool status)
	Set the RF Switch I/Os pins in Low Power mode.
virtual void	AntSwInit (void)
	Initializes the RF Switch I/Os pins interface.
virtual void	AntSwDeInit (void)
	De-initializes the RF Switch I/Os pins interface.
virtual void	SetAntSw (uint8_t opMode)
	Controls the antena switch if necessary.
void	RxChainCalibration (void)
virtual void	SetOpMode (uint8_t opMode)
	Sets the SX1276 operating mode.
virtual void	OnDio0Irq (void)
	DIO 0 IRQ callback.
virtual void	OnDio1Irq (void)
	DIO 1 IRQ callback.
virtual void	OnDio2Irq (void)
	DIO 2 IRQ callback.
virtual void	OnDio3Irq (void)
	DIO 3 IRQ callback.
virtual void	OnDio4Irq (void)
	DIO 4 IRQ callback.
virtual void	OnDio5Irq (void)
	DIO 5 IRQ callback.
virtual void	OnTimeoutIrq (void)
	Tx & Rx timeout timer callback.
Static Protected Member Functions
static uint8_t	GetFskBandwidthRegValue (uint32_t bandwidth)
static uint8_t	GetLoRaBandwidthRegValue (uint32_t bandwidth)
Protected Attributes
DigitalOut *	_antSwitch
DigitalInOut *	_reset
DigitalOut *	_tcxo
XSPI *	_spi
InterruptIn *	_dio0
Timeout	txTimeoutTimer
DioIrqHandler *	dioIrq

Detailed Description

Actual implementation of a SX1276 radio, includes some modifications to make it compatible with the MB1 LAS board

Definition at line 38 of file sx1276-mbed-hal.h.

Member Typedef Documentation

typedef void( SX1276::* DioIrqHandler)(void) [protected, inherited]

Hardware IO IRQ callback function definition

Definition at line 124 of file sx1276.h.

Member Function Documentation

void AntSwDeInit ( void ) [protected, virtual]

De-initializes the RF Switch I/Os pins interface.

Remarks:: Needed to decrease the power consumption in MCU lowpower modes

Implements SX1276.

Definition at line 292 of file sx1276-mbed-hal.cpp.

void AntSwInit ( void ) [protected, virtual]

Initializes the RF Switch I/Os pins interface.

Implements SX1276.

Definition at line 282 of file sx1276-mbed-hal.cpp.

bool CheckRfFrequency ( uint32_t frequency ) [virtual]

Checks if the given RF frequency is supported by the hardware.

Parameters:

[IN]	frequency RF frequency to be checked

Return values:

isSupported [true: supported, false: unsupported]

Implements SX1276.

Definition at line 376 of file sx1276-mbed-hal.cpp.

uint8_t DetectBoardType ( void ) [virtual]

Detect the board connected by reading the value of the antenna switch pin.

Definition at line 137 of file sx1276-mbed-hal.cpp.

int32_t GetFrequencyError ( RadioModems_t modem ) [virtual, inherited]

Reads the current frequency error.

Return values:

frequency error value in [Hz]

Implements Radio.

Definition at line 1116 of file sx1276.cpp.

uint8_t GetFskBandwidthRegValue ( uint32_t bandwidth ) [static, protected, inherited]

Returns the known FSK bandwidth registers value

Parameters:

[IN]	bandwidth Bandwidth value in Hz

Return values:

regValue Bandwidth register value.

Definition at line 259 of file sx1276.cpp.

uint8_t GetLoRaBandwidthRegValue ( uint32_t bandwidth ) [static, protected, inherited]

Returns the known LoRa bandwidth registers value

Parameters:

[IN]	bandwidth Bandwidth value in Hz

Return values:

regValue Bandwidth register value.

Definition at line 280 of file sx1276.cpp.

uint8_t GetPaSelect ( uint32_t channel ) [protected, virtual]

Gets the board PA selection configuration.

Parameters:

[IN]	channel Channel frequency in Hz

Return values:

PaSelect RegPaConfig PaSelect value

Implements SX1276.

Definition at line 246 of file sx1276-mbed-hal.cpp.

int16_t GetRssi ( RadioModems_t modem ) [virtual, inherited]

Reads the current RSSI value.

Return values:

rssiValue Current RSSI value in [dBm]

Implements Radio.

Definition at line 1090 of file sx1276.cpp.

RadioState GetStatus ( void ) [virtual, inherited]

Return current radio status

Parameters:

status Radio status. [RF_IDLE, RX_RUNNING, TX_RUNNING, CAD_RUNNING]

Implements Radio.

Definition at line 141 of file sx1276.cpp.

bool Init ( RadioEvents_t * events ) [virtual, inherited]

Return current radio status, returns true if a radios has been found.

Parameters:

[IN]	events Structure containing the driver callback functions

Implements Radio.

Definition at line 120 of file sx1276.cpp.

void IoDeInit ( void ) [protected, virtual]

De-initializes the radio I/Os pins interface.

Remarks:: Useful when going in MCU lowpower modes

Implements SX1276.

Definition at line 178 of file sx1276-mbed-hal.cpp.

void IoInit ( void ) [protected, virtual]

Initializes the radio I/Os pins interface.

Implements SX1276.

Definition at line 142 of file sx1276-mbed-hal.cpp.

void IoIrqInit ( DioIrqHandler * irqHandlers ) [protected, virtual]

Initializes DIO IRQ handlers.

Parameters:

[IN]	irqHandlers Array containing the IRQ callback functions

Implements SX1276.

Definition at line 164 of file sx1276-mbed-hal.cpp.

bool IsChannelFree	(	RadioModems_t	modem,
		uint32_t	freq,
		int16_t	rssiThresh
	)		`[virtual, inherited]`

Sets the channels configuration.

Parameters:

[IN]	modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]	freq Channel RF frequency
[IN]	rssiThresh RSSI threshold

Return values:

isFree [true: Channel is free, false: Channel is not free]

Implements Radio.

Definition at line 155 of file sx1276.cpp.

int16_t MaxMTUSize ( RadioModems_t modem ) [virtual, inherited]

Returns the maximal transfer unit for a given modem.

Return values:

MTU	size in bytes

Implements Radio.

Definition at line 1072 of file sx1276.cpp.

void OnDio0Irq ( void ) [protected, virtual, inherited]

DIO 0 IRQ callback.

Definition at line 1303 of file sx1276.cpp.

void OnDio1Irq ( void ) [protected, virtual, inherited]

DIO 1 IRQ callback.

Definition at line 1503 of file sx1276.cpp.

void OnDio2Irq ( void ) [protected, virtual, inherited]

DIO 2 IRQ callback.

Definition at line 1580 of file sx1276.cpp.

void OnDio3Irq ( void ) [protected, virtual, inherited]

DIO 3 IRQ callback.

Definition at line 1650 of file sx1276.cpp.

void OnDio4Irq ( void ) [protected, virtual, inherited]

DIO 4 IRQ callback.

Definition at line 1681 of file sx1276.cpp.

void OnDio5Irq ( void ) [protected, virtual, inherited]

DIO 5 IRQ callback.

Definition at line 1700 of file sx1276.cpp.

void OnTimeoutIrq ( void ) [protected, virtual, inherited]

Tx & Rx timeout timer callback.

Definition at line 1232 of file sx1276.cpp.

void RadioRegistersInit ( void ) [virtual, inherited]

Initializes the radio registers.

Definition at line 130 of file sx1276.cpp.

uint32_t Random ( void ) [virtual, inherited]

Generates a 32 bits random value based on the RSSI readings.

Remarks:: This function sets the radio in LoRa modem mode and disables all interrupts. After calling this function either Radio.SetRxConfig or Radio.SetTxConfig functions must be called.

Return values:

randomValue 32 bits random value

Implements Radio.

Definition at line 178 of file sx1276.cpp.

void Read	(	uint8_t	addr,
		void *	buffer,
		uint8_t	size
	)		`[virtual]`

Reads multiple radio registers starting at address.

Parameters:

[IN]	addr First Radio register address
[OUT]	buffer Buffer where to copy the registers data
[IN]	size Number of registers to be read

Implements SX1276.

Definition at line 420 of file sx1276-mbed-hal.cpp.

uint8_t Read ( uint8_t addr ) [virtual]

Reads the radio register at the specified address.

Parameters:

[IN],: addr Register address

Return values:

data	Register value

Implements SX1276.

Definition at line 399 of file sx1276-mbed-hal.cpp.

void ReadFifo	(	void *	buffer,
		uint8_t	size
	)		`[virtual]`

Reads the contents of the SX1276 FIFO.

Parameters:

[OUT]	buffer Buffer where to copy the FIFO read data.
[IN]	size Number of bytes to be read from the FIFO

Implements SX1276.

Definition at line 439 of file sx1276-mbed-hal.cpp.

void Reset ( void ) [virtual]

Reset the SX1276.

Implements SX1276.

Definition at line 384 of file sx1276-mbed-hal.cpp.

void Rx ( uint32_t timeout ) [virtual, inherited]

Sets the radio in reception mode for the given time.

Parameters:

[IN]	timeout Reception timeout [ms] [0: continuous, others timeout]

Implements Radio.

Definition at line 780 of file sx1276.cpp.

void RxChainCalibration ( void ) [protected, inherited]

Performs the Rx chain calibration for LF and HF bands

Remarks:: Must be called just after the reset so all registers are at their default values

Definition at line 219 of file sx1276.cpp.

bool RxSignalPending ( ) [virtual, inherited]

Check is radio receives a signal.

Implements Radio.

Definition at line 942 of file sx1276.cpp.

void Send	(	void *	buffer,
		int16_t	size,
		void *	header = `NULL`,
		int16_t	hsize = `0`
	)		`[virtual, inherited]`

Sends the buffer of size. Prepares the packet to be sent and sets the radio in transmission.

Parameters:

[IN],:	buffer Buffer pointer
[IN],:	size Buffer size
[IN],:	buffer Header pointer
[IN],:	size Header size

Implements Radio.

Definition at line 679 of file sx1276.cpp.

void SetAntSw ( uint8_t opMode ) [protected, virtual]

Controls the antena switch if necessary.

Remarks:: see errata note

Parameters:

[IN]	opMode Current radio operating mode

Implements SX1276.

Definition at line 303 of file sx1276-mbed-hal.cpp.

void SetAntSwLowPower ( bool status ) [protected, virtual]

Set the RF Switch I/Os pins in Low Power mode.

Parameters:

[IN]	status enable or disable

Implements SX1276.

Definition at line 265 of file sx1276-mbed-hal.cpp.

void SetChannel ( uint32_t freq ) [virtual, inherited]

Sets the channel frequency.

Parameters:

[IN]	freq Channel RF frequency

Implements Radio.

Definition at line 146 of file sx1276.cpp.

void SetMaxPayloadLength	(	RadioModems_t	modem,
		uint8_t	max
	)		`[virtual, inherited]`

Sets the maximum payload length.

Parameters:

[IN]	modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]	max Maximum payload length in bytes

Implements Radio.

Definition at line 1197 of file sx1276.cpp.

void SetModem ( RadioModems_t modem ) [virtual, inherited]

Configures the SX1276 with the given modem.

Parameters:

[IN]	modem Modem to be used [0: FSK, 1: LoRa]

Implements Radio.

Definition at line 1160 of file sx1276.cpp.

void SetOpMode ( uint8_t opMode ) [protected, virtual, inherited]

Sets the SX1276 operating mode.

Parameters:

[IN]	opMode New operating mode

Definition at line 1146 of file sx1276.cpp.

void SetPublicNetwork ( bool enable ) [virtual, inherited]

Sets the network to public or private. Updates the sync byte.

Remarks:: Applies to LoRa modem only

Parameters:

[IN]	enable if true, it enables a public network

Implements Radio.

Definition at line 1215 of file sx1276.cpp.

void SetRfTxPower ( int8_t power ) [virtual]

Sets the radio output power.

Parameters:

[IN]	power Sets the RF output power

Implements SX1276.

Definition at line 183 of file sx1276-mbed-hal.cpp.

void SetRxConfig	(	RadioModems_t	modem,
		uint32_t	bandwidth,
		uint32_t	datarate,
		uint8_t	coderate,
		uint32_t	bandwidthAfc,
		uint16_t	preambleLen,
		uint16_t	symbTimeout,
		bool	fixLen,
		uint8_t	payloadLen,
		bool	crcOn,
		bool	freqHopOn,
		uint8_t	hopPeriod,
		bool	iqInverted,
		bool	rxContinuous
	)		`[virtual, inherited]`

Sets the reception parameters.

Parameters:

[IN]	modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]	bandwidth Sets the bandwidth FSK : >= 2600 and <= 250000 Hz LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
[IN]	datarate Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
[IN]	coderate Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
[IN]	bandwidthAfc Sets the AFC Bandwidth ( FSK only ) FSK : >= 2600 and <= 250000 Hz LoRa: N/A ( set to 0 )
[IN]	preambleLen Sets the Preamble length ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: Length in symbols ( the hardware adds 4 more symbols )
[IN]	symbTimeout Sets the RxSingle timeout value FSK : timeout number of bytes LoRa: timeout in symbols
[IN]	fixLen Fixed length packets [0: variable, 1: fixed]
[IN]	payloadLen Sets payload length when fixed lenght is used
[IN]	crcOn Enables/Disables the CRC [0: OFF, 1: ON]
[IN]	freqHopOn Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
[IN]	hopPeriod Number of symbols bewteen each hop (LoRa only)
[IN]	iqInverted Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
[IN]	rxContinuous Sets the reception in continuous mode [false: single mode, true: continuous mode]

Implements Radio.

Definition at line 295 of file sx1276.cpp.

void SetTxConfig	(	RadioModems_t	modem,
		int8_t	power,
		uint32_t	fdev,
		uint32_t	bandwidth,
		uint32_t	datarate,
		uint8_t	coderate,
		uint16_t	preambleLen,
		bool	fixLen,
		bool	crcOn,
		bool	freqHopOn,
		uint8_t	hopPeriod,
		bool	iqInverted,
		uint32_t	timeout
	)		`[virtual, inherited]`

Sets the transmission parameters.

Parameters:

[IN]	modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]	power Sets the output power [dBm]
[IN]	fdev Sets the frequency deviation ( FSK only ) FSK : [Hz] LoRa: 0
[IN]	bandwidth Sets the bandwidth ( LoRa only ) FSK : 0 LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
[IN]	datarate Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
[IN]	coderate Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
[IN]	preambleLen Sets the preamble length
[IN]	fixLen Fixed length packets [0: variable, 1: fixed]
[IN]	crcOn Enables disables the CRC [0: OFF, 1: ON]
[IN]	freqHopOn Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
[IN]	hopPeriod Number of symbols bewteen each hop (LoRa only)
[IN]	iqInverted Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
[IN]	timeout Transmission timeout [ms]

Implements Radio.

Definition at line 467 of file sx1276.cpp.

void SetTxContinuousWave	(	uint32_t	freq,
		int8_t	power,
		uint16_t	time
	)		`[virtual, inherited]`

Sets the radio in continuous wave transmission mode.

Parameters:

[IN],:	freq Channel RF frequency
[IN],:	power Sets the output power [dBm]
[IN],:	time Transmission mode timeout [s]

Implements Radio.

Definition at line 1054 of file sx1276.cpp.

void Sleep ( void ) [virtual, inherited]

Sets the radio in sleep mode.

Implements Radio.

Definition at line 762 of file sx1276.cpp.

void SpiInit ( void ) [protected, virtual]

Initializes the radio SPI.

Implements SX1276.

Definition at line 151 of file sx1276-mbed-hal.cpp.

void Standby ( void ) [virtual, inherited]

Sets the radio in standby mode.

Implements Radio.

Definition at line 771 of file sx1276.cpp.

void StartCad ( void ) [virtual, inherited]

Sets the radio in CAD mode.

Implements Radio.

Definition at line 1021 of file sx1276.cpp.

uint32_t TimeOnAir	(	RadioModems_t	modem,
		int16_t	pktLen
	)		`[virtual, inherited]`

Computes the packet time on air for the given payload.

Can only be called once SetRxConfig or SetTxConfig have been called

Parameters:

[IN]	modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]	pktLen Packet payload length

Return values:

airTime Computed airTime for the given packet payload length

Implements Radio.

Definition at line 600 of file sx1276.cpp.

void Tx ( uint32_t timeout ) [virtual, inherited]

Sets the radio in transmission mode for the given time.

Parameters:

[IN]	timeout Transmission timeout [ms] [0: continuous, others timeout]

Implements Radio.

Definition at line 959 of file sx1276.cpp.

void Write	(	uint8_t	addr,
		void *	buffer,
		uint8_t	size
	)		`[virtual]`

Writes multiple radio registers starting at address.

Parameters:

[IN]	addr First Radio register address
[IN]	buffer Buffer containing the new register's values
[IN]	size Number of registers to be written

Implements SX1276.

Definition at line 406 of file sx1276-mbed-hal.cpp.

void Write	(	uint8_t	addr,
		uint8_t	data
	)		`[virtual]`

Writes the radio register at the specified address.

Parameters:

[IN],:	addr Register address
[IN],:	data New register value

Implements SX1276.

Definition at line 394 of file sx1276-mbed-hal.cpp.

void WriteFifo	(	void *	buffer,
		uint8_t	size
	)		`[virtual]`

Writes the buffer contents to the SX1276 FIFO.

Parameters:

[IN]	buffer Buffer containing data to be put on the FIFO.
[IN]	size Number of bytes to be written to the FIFO

Implements SX1276.

Definition at line 434 of file sx1276-mbed-hal.cpp.

Field Documentation

DigitalOut* _antSwitch [protected]

Antenna switch GPIO pins objects

Definition at line 44 of file sx1276-mbed-hal.h.

InterruptIn* _dio0 [protected]

SX1276 DIO pins

Definition at line 67 of file sx1276-mbed-hal.h.

DigitalInOut* _reset [protected]

SX1276 Reset pin

Definition at line 51 of file sx1276-mbed-hal.h.

XSPI* _spi [protected]

SPI Interface

Definition at line 61 of file sx1276-mbed-hal.h.

DigitalOut* _tcxo [protected]

TCXO being used with the Murata Module

Definition at line 56 of file sx1276-mbed-hal.h.

DioIrqHandler* dioIrq [protected, inherited]

Hardware DIO IRQ functions

Definition at line 129 of file sx1276.h.

const SX1276::RadioRegisters RadioRegsInit [static, inherited]

Initial value:

 {
    { MODEM_FSK , REG_LNA                , 0x23 },
    { MODEM_FSK , REG_RXCONFIG           , 0x1E },
    { MODEM_FSK , REG_RSSICONFIG         , 0xD2 },
    { MODEM_FSK , REG_AFCFEI             , 0x01 },
    { MODEM_FSK , REG_PREAMBLEDETECT     , 0xAA },
    { MODEM_FSK , REG_OSC                , 0x07 },
    { MODEM_FSK , REG_SYNCCONFIG         , 0x12 },
    { MODEM_FSK , REG_SYNCVALUE1         , 0xC1 },
    { MODEM_FSK , REG_SYNCVALUE2         , 0x94 },
    { MODEM_FSK , REG_SYNCVALUE3         , 0xC1 },
    { MODEM_FSK , REG_PACKETCONFIG1      , 0xD8 },
    { MODEM_FSK , REG_FIFOTHRESH         , 0x8F },
    { MODEM_FSK , REG_IMAGECAL           , 0x02 },
    { MODEM_FSK , REG_DIOMAPPING1        , 0x00 },
    { MODEM_FSK , REG_DIOMAPPING2        , 0x30 },
    { MODEM_LORA, REG_LR_PAYLOADMAXLENGTH, 0x40 },
    
}

Radio hardware registers initialization definition.

Remarks:: Can be automatically generated by the SX1276 GUI (not yet implemented)

Definition at line 487 of file sx1276.h.

Timeout txTimeoutTimer [protected]

Tx and Rx timers

Definition at line 77 of file sx1276-mbed-hal.h.

Type:	Library
Created:	18 Apr 2019
Imports:	7
Forks:	0
Commits:	120
Dependents:	5
Dependencies:	0
Followers:	1

Important changes to repositories hosted on mbed.com

SX1276Generic Class Reference

Public Member Functions

Static Public Attributes

Protected Types

Protected Member Functions

Static Protected Member Functions

Protected Attributes

Detailed Description

Member Typedef Documentation

Member Function Documentation

Field Documentation

Repository toolbox

Repository details

Important Information for this Arm website

Important changes to repositories hosted on mbed.com

SX1276Generic Class Reference

Public Member Functions

Static Public Attributes

Protected Types

Protected Member Functions

Static Protected Member Functions

Protected Attributes

Detailed Description

Member Typedef Documentation

Member Function Documentation

Field Documentation

Repository toolbox

Repository details

Important Information for this Arm website

Access Warning