A simple oscilloscope using Adafruit 2.8" TFT with touch. Runs on FRDM-KL25Z, FRDM-K22F, FRDM-K64F, NUCLEO-F411RE. 2 channel analog inputs with 4 trigger modes and time division.
Dependencies: SPI_STMPE610 UniGraphic mbed vt100
My first attempt of implementing an oscilloscope using FRDM-KL25Z and Adafruit 2.8" TFT with touch.
FRDM-KL25Z と Adafruit 2.8" TFT with touch を使用して作ってみた最初のオシロスコープです。
On 25-Sep-2017, wrong calculation of trigger pos/val fixed.
On 25-Nov-2015, FRDM-K64F and NUCLEO-F411RE platforms were added.
On 26-Nov-2015, FRDM-K22F is added (tested).
Note: Now ch2 is A2 instead of A1!
25-Sep-2017, トリガー値と位置の計算の誤りを修正しました。
25-Nov-2015, FRDM-K64F と NUCLEO-F411RE でも動くようになりました。
26-Nov-2015, FRDM-K22F でも動作確認が出来ました。
※一身上の都合で、アナログ入力の ch2 は A1 から A2 に変更しましたので、ご注意ください。m(_ _)m
This supports two analog inputs A0 for channel 1 and A2 for channel 2
and four trigger modes (NONE, RISE, FALL, LEVEL),
time division is 30us to 20ms per pixel which will make 300us/div to 200.0ms/div (as 10 pixels per div)
A0と A2 のアナログ2入力にて、
4種類のトリガーモード(NONE: フリーラン RISE: 立ち上がりエッジ、FALL: 立下りエッジ、LEVEL: レベル) 。
サンプリングは30us から 20ms, チャートの1メモリが10ピクセルなので、300us/dev から 200.0ms/div となっています。
The analog signals and gnd was picked at the pins in the picture above.
Note: now you need to pick A0 and A2 instead of A0 and A1.
信号は上記の写真のように、Adafruit のピンからつまみました。
変更により、A0とA2が入力となります。
When powered on or reset, the program starts in Trigger Mode = NONE (Free Run Mode)
電源投入、リセット後 プログラムはトリガーモード NONE (フリーランモード) で起動します。
To change trigger mode and/or time division, press run/stop button.
トリガーモードを変えたり、サンプリング時間を変えるのには run/stop ボタンを押してください。
Each time you push Trig button, the trigger mode changes
NONE -> RISE -> FALL -> LEVEL ( -> NONE).
トリガーボタンを押すたびにトリガーモードは
NONE(フリーラン) -> RISE (立ち上がりエッジ) -> FALL (立下りエッジ) -> LEVEL (レベル)
と変化します。
When trigger mode is not NONE,
to specify the trigger position, level and channel, push inside the wave frame.
Then green trigger marks will be shown and value of trigger position and voltage will be printed.
トリガーモードが NONE でないときに、チャネルの枠内をタッチしますと、
その位置がトリガーのポジション、レベル、チャネルになります。
そして、緑色のトリガーマークが表示され、下部にはトリガーの具体的なポジションとボルテージが表示されます。
To change time division push
"1/2" to Zoom Out (sampling interval will be bigger) or
"x2" to Zoom In (Sampling interval will be smaller).
サンプリングタイムを変更するのには
"1/2" ズームアウト (サンプリング間隔が長くなります) か
"x2" ズームイン (サンプリング間隔が短くなります。) を押してください。
On 7-Mar-2015 updated to UniGraphic library version!
2015年3月7日 UniGraphic ライブラリ使用版にアップデートしました。
FRDM-KL25Z
FRDM-K64F
NUCLEO-F411RE
Diff: main.h
- Revision:
- 6:c93e2f12b789
- Parent:
- 4:6f3532a1a962
- Child:
- 8:62982cc8e5d8
diff -r 0cffd2b70a1e -r c93e2f12b789 main.h --- a/main.h Wed Nov 25 12:56:02 2015 +0000 +++ b/main.h Wed Nov 25 13:07:28 2015 +0000 @@ -10,59 +10,96 @@ * THE SOFTWARE. */ #ifndef _MAIN_H_ -#define _MAIN_H_ inluded - -// uncomment following line if K64F rev is E or later -#define FRDM_K64F_VE +#define _MAIN_H_ included -#if defined (TARGET_KL25Z) +#if defined (TARGET_KL25Z) +#define PIN_SCLK PTD1 +#define PIN_MISO PTD3 #define PIN_MOSI PTD2 -#define PIN_MISO PTD3 -#define PIN_SCLK PTD1 #define PIN_CS_TFT PTD0 #define PIN_DC_TFT PTD5 +#define PIN_CS_TSC PTA13 #define PIN_BL_TFT PTC9 #define PIN_CS_SD PTA4 -#define PIN_CS_TSC PTA13 -#define PIN_TSC_INTR PTC9 -#define PIN_RESET_TFT PTB10 +#define PIN_TSC_INTR PTC9 /* place holder */ +#define PIN_RESET_TFT PTB10 /* place holder */ #define PIN_ADC_CH0 PTB0 -#define PIN_ADC_CH1 PTB1 +#define PIN_ADC_CH1 PTB2 #elif defined (TARGET_KL46Z) -#define PIN_MOSI PTD6 +#define PIN_SCLK PTD5 #define PIN_MISO PTD7 -#define PIN_SCLK PTD5 +#define PIN_MOSI PTD6 #define PIN_CS_TFT PTD4 #define PIN_DC_TFT PTD2 +#define PIN_CS_TSC PTA13 #define PIN_BL_TFT PTC9 #define PIN_CS_SD PTA4 -#define PIN_CS_TSC PTA13 -#define PIN_TSC_INTR PTC9 -#define PIN_RESET_TFT PTA20 +#define PIN_TSC_INTR PTC7 /* place holder */ +#define PIN_RESET_TFT PTC6 /* place holder */ #define PIN_ADC_CH0 PTB0 -#define PIN_ADC_CH1 PTB1 +#define PIN_ADC_CH1 PTB2 #elif defined (TARGET_K64F) -#define PIN_MOSI PTD2 +#define PIN_SCLK PTD1 #define PIN_MISO PTD3 -#define PIN_SCLK PTD1 +#define PIN_MOSI PTD2 #define PIN_CS_TFT PTD0 #define PIN_DC_TFT PTC4 +// for board rev E or later +#define PIN_CS_TSC PTC12 +// for earlier boards use following line +// #define PIN_CS_TSC PTA0 #define PIN_BL_TFT PTC3 #define PIN_CS_SD PTB23 -#ifdef FRDM_K64F_VE -#define PIN_CS_TSC PTC12 -#else -#define PIN_CS_TSC PTA0 -#endif -#define PIN_TSC_INTR PTC3 -#define PIN_RESET_TFT PTB20 +#define PIN_TSC_INTR PTC0 /* place holder */ +#define PIN_RESET_TFT PTC9 /* place holder */ #define PIN_ADC_CH0 PTB2 -#define PIN_ADC_CH1 PTB3 +#define PIN_ADC_CH1 PTB10 + +#elif defined (TARGET_K22F) +#define PIN_SCLK PTD5 +#define PIN_MISO PTD7 +#define PIN_MOSI PTD6 +#define PIN_CS_TFT PTD4 +#define PIN_DC_TFT PTA1 +#define PIN_CS_TSC PTB19 +#define PIN_BL_TFT PTC6 +#define PIN_CS_SD PTA4 +#define PIN_TSC_INTR PTC7 /* place holder */ +#define PIN_RESET_TFT PTC9 /* place holder */ +#define PIN_ADC_CH0 PTB0 +#define PIN_ADC_CH1 PTC1 + +#elif defined (TARGET_NUCLEO_F411RE) +#define PIN_SCLK PA_5 +#define PIN_MISO PA_6 +#define PIN_MOSI PA_7 +#define PIN_CS_TFT PB_6 +#define PIN_DC_TFT PC_7 +#define PIN_CS_TSC PA_9 +#define PIN_BL_TFT PA_8 +#define PIN_CS_SD PB_5 +#define PIN_TSC_INTR PA_8 /* place holder */ +#define PIN_RESET_TFT PA_13 /* place holder */ +#define PIN_ADC_CH0 PA_0 +#define PIN_ADC_CH1 PA_4 #else - #error TARGET NOT DEFINED + #error TARGET NOT DEFINED +#define PIN_SCLK D13 +#define PIN_MISO D12 +#define PIN_MOSI D11 +#define PIN_CS_TFT D10 +#define PIN_DC_TFT D9 +#define PIN_CS_TSC D8 +#define PIN_BL_TFT D7 +#define PIN_CS_SD D4 +#define PIN_TSC_INTR D5-inside /* place holder */ +#define PIN_RESET_TFT D4-inside /* place holder */ +#define PIN_ADC_CH0 A0 +#define PIN_ADC_CH1 A2 + #endif #define CHART_LEN 198