File content as of revision 19:886d50ecc718:

 #include "Lora.h"
 #include "OBD.h"
 #include "Common_Defs.h"
 #include "Beacon.h"
 
 //Configure Lora Packet
 RawSerial LORA_Module_UART(PA_0, PA_1);//USART4_TX->PA_0,USART4_RX->PA_1
 RawSerial pc2(PA_14, PA_15);//USART1_TX->PA_9,USART1_RX->PA_10
 Serial pc_2(USBTX, USBRX);

 uint8 Packet_Type_To_Send = HEARTBEAT_TYPE_PACKET;  //By Default Heart Beat PAckets should be sent
 uint8 OBD_Protocol_Version = 0x01;
 uint8 Vehicle_Identification_Number[17];                     //Unique Vehicle_Identification_Number, Read using OBD
 uint8 Motion_Packet_Sent_Count=0;
 uint8 CheckIN_Packet_Sent_Count=0;
 uint8 Lora_Packet_To_Send[100];
 uint8 Send_Lora_Packet_Flag = FALSE;
 int Lora_RxBuffer_Crnt_Pos,Lora_RxBuffer_End_Pos; // must be volatile or the compiler may over-optimise.
 int receivedDataCount = 0;
 char LORA_UART_RX_Buffer[LORA_UART_RX_Size];
 int LORA_UART_RX_Crnt_Pos;
 uint8 Lora_Command_Rcvd[100];
 uint8 Lora_Cmd_Length = 0;
 uint8 AT_Response_Receive_Status = FAILURE; 
 
 //Create Object for Type of Lora Packet to send
 Heart_Beat_PacketType Heart_Beat_Lora_Packet;    //Allocate Memory for HeartBeat Lora Packets
 CheckIN_PacketType CheckIN_Lora_Packet; //Allocate Memory for CheckIN Lora Packets
 CheckOUT_PacketType CheckOUT_Packet; //Allocate Memory for CheckOUT Lora Packets
 Motion_PacketType Motion_Lora_Packet;    //Allocate Memory for Movement Lora Packets
 Vehicle_Status_PacketType Vehicle_Status_Lora_Packet;    //Allocate Memory for Movement Lora Packets
 Near_Car_Beacon Near_Car_Beacon_Packet;
 Fixed_Beacon Fixed_Beacon_Packet;
 Misc_Packets Misc_Packet_Data;
    
 //Lora AT Commands list
 const char* Attention = {"AT\r"};     
 const char* Reset_Device = "ATZ\r";
 const char* Reset_to_Factory_Defaults = "AT&F\r";
 const char* Save_Configuration = "AT&W\r";
 const char* Serial_Baud_Rate = "AT+IPR=";
 const char* Join_Network = "AT+JOIN\r";
 const char* Join_Retries = "AT+JR=";
 const char* AES_Encryption = "AT+ENC=";
 const char* Send_Lora_Packet = "AT+SEND ";
 const char* Set_Frequency_Sub_Band = "AT+FSB=";
 const char* Set_Network_ID = "AT+NI=";
 const char* Set_Network_Key = "AT+NK=";
 const char* Network_Key = "010203123";
 const char* Network_ID = "010203040";
 const char* Network_Join_Retries = "AT+JR=";
 const char* Network_Join_Status = "AT+NJS=";
 const char* Lora_Device_ID = "AT+DI\r";
 
 #define CHECK_IN_PACKET        0x00
 #define CHECK_OUT_PACKET       0x01

 uint8 Calculate_Lora_Frame_FCS(uint8* Packet_Data,uint8 Packet_Length);
 void Set_Up_Lora_Network_Configuration(void); 
 void Get_Lora_Response(void);
 
//Set Up lora network
void Set_Up_Lora_Network_Configuration(void)
{
    LORA_Module_UART.baud(115200);
    LORA_Module_UART.printf(Attention);//Send Attention command
    AT_Response_Receive_Status = FAILURE;
    pc2.printf("Nwk set up started");
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("AT Response received");
    LORA_Module_UART.printf("%s%d\r",Set_Frequency_Sub_Band,FREQUENCY_SUB_BAND_CHANNEL7);//set frequency sub band to 7
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("Frequency band response received");
    LORA_Module_UART.printf("%s%d,%s\r",Set_Network_Key,STRING_PARAMETER,Network_Key);   //set network key
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("Network key Response received");
    LORA_Module_UART.printf("%s%d,%s\r",Set_Network_ID,STRING_PARAMETER,Network_ID);     //set network id
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("Network Id response received");
    
    LORA_Module_UART.printf("AT+TXDR=DR2\r");
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    LORA_Module_UART.printf("AT+RXDR=10\r");
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    LORA_Module_UART.printf("AT+ADR=1\r"); //Enable adaptive data rate
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    LORA_Module_UART.printf("%s",Save_Configuration);              //save configuration          
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("Configuration saved");
    LORA_Module_UART.printf("%s",Reset_Device);                    //reset device
    wait_ms(3500);
    LORA_Module_UART.printf(Attention);        //Send Attention command
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("AT Response received");
    LORA_Module_UART.printf("%s",Join_Network);                    //join network with gateway
    AT_Response_Receive_Status = FAILURE;
    while(AT_Response_Receive_Status)
        Get_Lora_Response();
    pc2.printf("Join Response received");
}

 void Initialize_lora_Packets()
{
    uint8 i;
    /******* Initialize Lora packet for HeartBeat *****/
    Heart_Beat_Lora_Packet.Header = LORA_PACKET_HEADER;
    Misc_Packet_Data.Protocol_Version = OBD_Protocol_Version;
    Heart_Beat_Lora_Packet.Packet_Type = HEART_BEAT_PACKET_CMD;
    Misc_Packet_Data.OBD_Battery_Voltage = 350;       //3.50V, dummy data
    Misc_Packet_Data.Car_Battery_Voltage = 1250;      //12.50V, dummy data
    Misc_Packet_Data.OBD_Battery_Temperature = 95;    //95'F, dummy data
    Misc_Packet_Data.Car_Ambient_Temperature = 104;   //104'F, dummy data
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking1_Beacon_ID[i] = (0x01+i);      //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength = 23;             //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking2_Beacon_ID[i] = (10+i);      //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength = 45;             //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking3_Beacon_ID[i] = (20+i);      //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength = 12;             //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    Heart_Beat_Lora_Packet.FCS = 0x00;                                 //FCS of all packets        
    
    /******* Initialize Lora packet for Vehicle Status *****/
    Vehicle_Status_Lora_Packet.Header = LORA_PACKET_HEADER;
    Misc_Packet_Data.Protocol_Version = OBD_Protocol_Version;
    Vehicle_Status_Lora_Packet.Packet_Type = STATUS_PACKET_CMD;
    for(i=0;i<17;i++)
        Misc_Packet_Data.VIN[i] = (30+i);//Vehicle_Identification_Number[i];
    for(i=0;i<3;i++)
        Misc_Packet_Data.ODO_METER_READING[i] = 0x05;  //Dummyy data, To be read using OBD
    Vehicle_Status_Lora_Packet.Fuel_Level = 1050;//10.5 litre
    Misc_Packet_Data.OBD_Battery_Voltage = 350;
    Misc_Packet_Data.Car_Battery_Voltage = 1250;
    Misc_Packet_Data.OBD_Battery_Temperature = 95;
    Misc_Packet_Data.Car_Ambient_Temperature = 104;
    for(i=0;i<6;i++)
        Vehicle_Status_Lora_Packet.BLE_Adv_Beacon_ID[i] = BLE_Adv_Module_Beacon_ID[i];         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking1_Beacon_ID[i] = (30+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength = 0x07;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking2_Beacon_ID[i] = (40+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength = 0x08;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking3_Beacon_ID[i] = (50+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength = 0x09;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Near_Car_Beacon_Packet.Near_Car1_Beacon_ID[i] = (60+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Near_Car_Beacon_Packet.Near_Car1_Beacon_Signal_Strength = 0x09;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Near_Car_Beacon_Packet.Near_Car2_Beacon_ID[i] = (70+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Near_Car_Beacon_Packet.Near_Car2_Beacon_Signal_Strength = 0x09;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Near_Car_Beacon_Packet.Near_Car3_Beacon_ID[i] = (80+i);         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Near_Car_Beacon_Packet.Near_Car3_Beacon_Signal_Strength = 0x09;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    Vehicle_Status_Lora_Packet.FCS = 0x00;                       //FCS of all packets     
    
    /******* Initialize Lora packet for CheckIn *****/
    CheckIN_Lora_Packet.Header = LORA_PACKET_HEADER;
    Misc_Packet_Data.Protocol_Version = OBD_Protocol_Version;
    CheckIN_Lora_Packet.Packet_Type = CHECKIN_PACKET_CMD;
    for(i=0;i<17;i++)
        Misc_Packet_Data.VIN[i] = Vehicle_Identification_Number[i];
    for(i=0;i<3;i++)
        Misc_Packet_Data.ODO_METER_READING[i] = 0x00;  //Dummyy data, To be read using OBD
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking1_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking2_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking3_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    CheckIN_Lora_Packet.FCS = 0x00;                       //FCS of all packets     
       
    /******* Initialize Lora packet for CheckOUT *****/
    CheckOUT_Packet.Header = LORA_PACKET_HEADER;
    Misc_Packet_Data.Protocol_Version = OBD_Protocol_Version;
    CheckOUT_Packet.Packet_Type = CHECKIN_PACKET_CMD;
    for(i=0;i<17;i++)
        Misc_Packet_Data.VIN[i] = Vehicle_Identification_Number[i];
    for(i=0;i<3;i++)
        Misc_Packet_Data.ODO_METER_READING[i] = 0x00;  //Dummyy data, To be read using OBD
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking1_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking2_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking3_Beacon_ID[i] = 0x00;         //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength = 0x00;   //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    CheckOUT_Packet.FCS = 0x00;                       //FCS of all packets     
       
    /******* Initialize Lora packet for Movement *****/
    Motion_Lora_Packet.Header = LORA_PACKET_HEADER;
    Misc_Packet_Data.Protocol_Version = OBD_Protocol_Version;
    Motion_Lora_Packet.Packet_Type = MOTION_PACKET_CMD;
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking1_Beacon_ID[i] = 0x00;          //MAC ID of 1st NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength = 0x00;    //Signal Strength of 1st NearBy Beacon Device with Highest Signal Strength      
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking2_Beacon_ID[i] = 0x00;          //MAC ID of 2nd NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength = 0x00;    //Signal Strength of 2nd NearBy Beacon Device with Highest Signal Strength          
    for(i=0;i<6;i++)
        Fixed_Beacon_Packet.Parking3_Beacon_ID[i] = 0x00;          //MAC ID of 3rd NearBy Beacon Device with Highest Signal Strength,dummy data
    Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength = 0x00;    //Signal Strength of 3rd NearBy Beacon Device with Highest Signal Strength          
    Motion_Lora_Packet.Acceleration_Type = 0x00;          //Type of acceleration, Vehicle Started/Vehicle Stopped/Sudden Vehicle Movement
    Motion_Lora_Packet.FCS = 0x00;                        //FCS of all packets  
 
}
               
 //HeartBeat Packet should be sent every 30sec
void Send_HeartBeat_Packet(void)
{
    //write code to read obd data,temperature,beacon data
    uint8 Pos = 0,i;
    Lora_Packet_To_Send[Pos++] = Heart_Beat_Lora_Packet.Header;                  //Header of Lora Packet,0xFE
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Protocol_Version;
    Lora_Packet_To_Send[Pos++] = Heart_Beat_Lora_Packet.Packet_Type;      //MSB of Motion Packet Type
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage >> 8);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage & 0xFF);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage >> 8); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage & 0xFF); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.OBD_Battery_Temperature;     //Get Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Car_Ambient_Temperature;     //Get Ambient Temperature
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Calculate_Lora_Frame_FCS(Lora_Packet_To_Send,Pos);   //Calculate FCS of all bytes
    Packet_Type_To_Send = HEARTBEAT_TYPE_PACKET;
    Send_Lora_Packet_To_Gateway(Lora_Packet_To_Send,Pos); 
}

//CheckIN packets sending should be started when device is plugged in to the vehicle. It should be sent every 5sec for 2minutes and afterthat it should stop sending
void Send_Vehicle_Status_Packet(void)
{
    //write code to read OBD data,temperature,beacon data
    uint8 Pos = 0,i;
    Lora_Packet_To_Send[Pos++] = Vehicle_Status_Lora_Packet.Header;                  //Header of Lora Packet,0xFE
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Protocol_Version;      //MSB of Motion Packet Type
    Lora_Packet_To_Send[Pos++] = Vehicle_Status_Lora_Packet.Packet_Type;      //MSB of Motion Packet Type
    for(i=0;i < 17;i++)
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.VIN[i];           //Get OBD_ID
    for(i=0;i < 3;i++)
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.ODO_METER_READING[i];           //Get OBD_ID
    Lora_Packet_To_Send[Pos++] = (Vehicle_Status_Lora_Packet.Fuel_Level >> 8);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Vehicle_Status_Lora_Packet.Fuel_Level & 0xFF);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage >> 8);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage & 0xFF);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage >> 8); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage & 0xFF); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.OBD_Battery_Temperature;     //Get Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Car_Ambient_Temperature;     //Get Ambient Temperature
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Vehicle_Status_Lora_Packet.BLE_Adv_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Calculate_Lora_Frame_FCS(Lora_Packet_To_Send,Pos);   //Calculate FCS of all bytes
    Send_Lora_Packet_To_Gateway(Lora_Packet_To_Send,Pos); 
}

//CheckIN packets sending should be started when device is plugged in to the vehicle. It should be sent every 5sec for 2minutes and afterthat it should stop sending
void Send_CheckIN_Packet(void)
{
    //write code to read OBD data,temperature,beacon data
    uint8 Pos = 0,i;
    Lora_Packet_To_Send[Pos++] = CheckIN_Lora_Packet.Header;                  //Header of Lora Packet,0xFE
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Protocol_Version;      //MSB of Motion Packet Type
    if(OBD_PlugIN_State)
        Lora_Packet_To_Send[Pos++] = CHECK_IN_PACKET;      //Check detected. Set packet type to Checkout type
    else
        Lora_Packet_To_Send[Pos++] = CHECK_OUT_PACKET;      //Checkout detected. Set packet type to Checkout type
    for(i=0;i < 17;i++)
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.VIN[i];           //Get OBD_ID
    for(i=0;i < 3;i++)
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.ODO_METER_READING[i];           //Get OBD_ID
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage >> 8);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage & 0xFF);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage >> 8); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage & 0xFF); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.OBD_Battery_Temperature;     //Get Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Car_Ambient_Temperature;     //Get Ambient Temperature
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Calculate_Lora_Frame_FCS(Lora_Packet_To_Send,Pos);   //Calculate FCS of all bytes
    CheckIN_Packet_Sent_Count++;
    Send_Lora_Packet_To_Gateway(Lora_Packet_To_Send,Pos); 
    pc2.printf("CheckIN Packet Sent");
}


//CheckIN packets sending should be started when device is plugged in to the vehicle. It should be sent every 5sec for 2minutes and afterthat it should stop sending
void Send_CheckOUT_Packet(void)
{
    //write code to read OBD data,temperature,beacon data
    uint8 Pos = 0,i;
    Lora_Packet_To_Send[Pos++] = CheckOUT_Packet.Header;                  //Header of Lora Packet,0xFE
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Protocol_Version;      //MSB of Motion Packet Type
    Lora_Packet_To_Send[Pos++] = CHECK_OUT_PACKET;      //Checkout detected. Set packet type to Checkout type
    for(i=0;i < 17;i++)
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.VIN[i];           //Get OBD_ID
    for(i=0;i < 3;i++) 
        Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.ODO_METER_READING[i];           //Get OBD_ID
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage >> 8);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.OBD_Battery_Voltage & 0xFF);     //Get OBD_Battery Voltage
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage >> 8); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = (Misc_Packet_Data.Car_Battery_Voltage & 0xFF); //Get Vehicle_Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.OBD_Battery_Temperature;     //Get Battery Temperature
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Car_Ambient_Temperature;     //Get Ambient Temperature
    Lora_Packet_To_Send[Pos++] = Calculate_Lora_Frame_FCS(Lora_Packet_To_Send,Pos);   //Calculate FCS of all bytes
    CheckIN_Packet_Sent_Count++;
    Send_Lora_Packet_To_Gateway(Lora_Packet_To_Send,Pos); 
    pc2.printf("CheckOUT Packet Sent");
    
}

//Motion packets sending should be started when vehicle acceleration changes like when it starts moving,stops moving and gets sudden jurk in case of theft.
// It should be sent every 30sec for 2minutes and afterthat it should stop sending
void Send_Motion_Packet(void)
{
    //write code to read accelerometer data,temperature,beacon data
    uint8 Pos = 0,i;
    Lora_Packet_To_Send[Pos++] = Motion_Lora_Packet.Header;                  //Header of Lora Packet,0xFE
    Lora_Packet_To_Send[Pos++] = Misc_Packet_Data.Protocol_Version;          //Protocol Version
    Lora_Packet_To_Send[Pos++] = (Motion_Lora_Packet.Packet_Type & 0xFF);         //LSB of Motion Packet Type
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Fixed_Beacon_Packet.Parking3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Motion_Lora_Packet.Acceleration_Type;       //get Type of Acceleration
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_ID[i];       //Get Beacon_ID of 1st nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car1_Beacon_Signal_Strength; //Get Signal Strength of 1st nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_ID[i];       //Get Beacon_ID of 2nd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car2_Beacon_Signal_Strength; //Get Signal Strength of 2nd nearby Beacon Device
    for(i=0;i<6;i++)
        Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_ID[i];       //Get Beacon_ID of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Near_Car_Beacon_Packet.Near_Car3_Beacon_Signal_Strength; //Get Signal Strength of 3rd nearby Beacon Device
    Lora_Packet_To_Send[Pos++] = Calculate_Lora_Frame_FCS(Lora_Packet_To_Send,Pos);   //Calculate FCS of all bytes
    Motion_Packet_Sent_Count++;
    Send_Lora_Packet_To_Gateway(Lora_Packet_To_Send,Pos); 
}   


void Get_Lora_Response(void)
{
    static uint16 Temp_Pos1;
    static uint8 Lora_Response_Found = 0x00; 
    static uint8 Response_Start_Pos[5];
    Lora_Response_Found = 0;
    Temp_Pos1 = LORA_UART_RX_Crnt_Pos = 0;
    while(Temp_Pos1 < Lora_RxBuffer_End_Pos) 
    { //check for end of AT response to calculate length
        if((LORA_UART_RX_Buffer[Temp_Pos1] != 0x0D) || (LORA_UART_RX_Buffer[Temp_Pos1+1] != 0x0A)) 
        { //check for  AT end response <cr><lf> (i.e. 0x0D,0x0A)
            Temp_Pos1++;
        }
        else
        {
            Temp_Pos1+=2;
            Response_Start_Pos[Lora_Response_Found++] = Temp_Pos1;
            //pc2.printf("%c",Temp_Pos1);
            if(Lora_Response_Found >= 4)
                break;
        }
    }
    if(Lora_Response_Found >= 3)
    {
        if((Response_Start_Pos[1] - Response_Start_Pos[0]) > 0x02) //Response received without data
        {
            LORA_UART_RX_Crnt_Pos = (Response_Start_Pos[0]);
            Response_Start_Pos[1]-=2;
            for(Temp_Pos1=0; LORA_UART_RX_Crnt_Pos < Response_Start_Pos[1]; Temp_Pos1++)
            {
                Lora_Command_Rcvd[Temp_Pos1] = LORA_UART_RX_Buffer[LORA_UART_RX_Crnt_Pos++];
                pc2.putc(Lora_Command_Rcvd[Temp_Pos1]);
            }
            Lora_RxBuffer_End_Pos = 0;
            AT_Response_Receive_Status = SUCCESS;
        }
        else if((Response_Start_Pos[1] - Response_Start_Pos[0]) == 0x02) //Response received along with data
        {
            LORA_UART_RX_Crnt_Pos = (Response_Start_Pos[1]);
            Response_Start_Pos[2]-=2;
            for(Temp_Pos1=0; LORA_UART_RX_Crnt_Pos < Response_Start_Pos[2]; Temp_Pos1++)
            {
                Lora_Command_Rcvd[Temp_Pos1] = LORA_UART_RX_Buffer[LORA_UART_RX_Crnt_Pos++];
                pc2.putc(Lora_Command_Rcvd[Temp_Pos1]);
            }
            Lora_RxBuffer_End_Pos = 0;
            AT_Response_Receive_Status = SUCCESS;
        }
    }
}

//Function to send general Lora packets using "AT+SEND" Command
void Send_Lora_Packet_To_Gateway(uint8* Command_To_Send,uint8 Length)
{
    uint8 i=0;
    LORA_Module_UART.printf("%s",Send_Lora_Packet);//write to serial port for sending through lora module
    LORA_Module_UART.printf("%s",Command_To_Send);
    LORA_Module_UART.printf("\r");
}
   

 unsigned char Calculate_Lora_Frame_FCS(unsigned char* Packet_Data,unsigned char Packet_Length)
 {
     uint8 i,FCS = 0x00;
     for(i=0; i < Packet_Length; i++)
     {
        FCS ^= (Packet_Data[i]);
     }
     return(FCS);
 }