![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
Original Version of STM Board
main.cpp
- Committer:
- hyhoon
- Date:
- 2021-03-11
- Revision:
- 227:699c3e572283
- Parent:
- 226:82a3ca333004
- Child:
- 228:763bbefcb79f
File content as of revision 227:699c3e572283:
//Hydraulic Control Board //distributed by Sungwoo Kim // 2020/12/28 // 유의사항 // 소수 적을때 뒤에 f 꼭 붙이기 // CAN 선은 ground까지 있는 3상 선으로 써야함. // 전원은 12~24V 인가. #include "mbed.h" #include "FastPWM.h" #include "INIT_HW.h" #include "function_CAN.h" #include "SPI_EEP_ENC.h" #include "I2C_AS5510.h" #include "setting.h" #include "function_utilities.h" #include "stm32f4xx_flash.h" #include "FlashWriter.h" #include <string> #include <iostream> #include <cmath> using namespace std; Timer t; // dac & check /////////////////////////////////////////// DigitalOut check(PC_2); DigitalOut check_2(PC_3); AnalogOut dac_1(PA_4); AnalogOut dac_2(PA_5); AnalogIn adc1(PC_4); //pressure_1 AnalogIn adc2(PB_0); //pressure_2 AnalogIn adc3(PC_1); //current // PWM /////////////////////////////////////////// float dtc_v=0.0f; float dtc_w=0.0f; // I2C /////////////////////////////////////////// I2C i2c(PC_9,PA_8); // SDA, SCL (for K22F) const int i2c_slave_addr1 = 0x56; // AS5510 address unsigned int value; // 10bit output of reading sensor AS5510 // SPI /////////////////////////////////////////// SPI eeprom(PB_15, PB_14, PB_13); // EEPROM //(SPI_MOSI, SPI_MISO, SPI_SCK); DigitalOut eeprom_cs(PB_12); SPI enc(PC_12,PC_11,PC_10); DigitalOut enc_cs(PD_2); DigitalOut LED(PA_15); // UART /////////////////////////////////////////// Serial pc(PA_9,PA_10); // _ UART // CAN /////////////////////////////////////////// CAN can(PB_8, PB_9, 1000000); CANMessage msg; void onMsgReceived() { CAN_RX_HANDLER(); } // Variables /////////////////////////////////////////// State pos; State vel; State Vout; State torq; State torq_dot; State pres_A; State pres_B; State cur; State valve_pos; State INIT_Vout; State INIT_Valve_Pos; State INIT_Pos; State INIT_torq; extern int CID_RX_CMD; extern int CID_RX_REF_POSITION; extern int CID_RX_REF_OPENLOOP; extern int CID_RX_REF_PWM; extern int CID_TX_INFO; extern int CID_TX_POS_VEL_TORQ; extern int CID_TX_PWM; extern int CID_TX_CURRENT; extern int CID_TX_VOUT; extern int CID_TX_VALVE_POSITION; extern int CID_TX_SOMETHING; float pres_A_new = 0.0f; float pres_B_new = 0.0f; float temp_P_GAIN = 0.0f; float temp_I_GAIN = 0.0f; int temp_VELOCITY_COMP_GAIN = 0; /******************************************************************************* * REFERENCE MODE ******************************************************************************/ enum _REFERENCE_MODE { MODE_REF_NO_ACT = 0, //0 MODE_REF_DIRECT, //1 MODE_REF_COS_INC, //2 MODE_REF_LINE_INC, //3 MODE_REF_SIN_WAVE, //4 MODE_REF_SQUARE_WAVE, //5 }; /******************************************************************************* * CONTROL MODE ******************************************************************************/ enum _CONTROL_MODE { //control mode MODE_NO_ACT = 0, //0 MODE_VALVE_POSITION_CONTROL, //1 MODE_JOINT_CONTROL, //2 MODE_VALVE_OPEN_LOOP, //3 MODE_JOINT_ADAPTIVE_BACKSTEPPING, //4 MODE_RL, //5 MODE_JOINT_POSITION_PRES_CONTROL_PWM, //6 MODE_JOINT_POSITION_PRES_CONTROL_VALVE_POSITION, //7 MODE_VALVE_POSITION_PRES_CONTROL_LEARNING, //8 MODE_TEST_CURRENT_CONTROL, //9 MODE_TEST_PWM_CONTROL, //10 MODE_CURRENT_CONTROL, //11 MODE_JOINT_POSITION_TORQUE_CONTROL_CURRENT, //12 MODE_JOINT_POSITION_PRES_CONTROL_CURRENT, //13 MODE_VALVE_POSITION_TORQUE_CONTROL_LEARNING, //14 //utility MODE_TORQUE_SENSOR_NULLING = 20, //20 MODE_VALVE_NULLING_AND_DEADZONE_SETTING, //21 MODE_FIND_HOME, //22 MODE_VALVE_GAIN_SETTING, //23 MODE_PRESSURE_SENSOR_NULLING, //24 MODE_PRESSURE_SENSOR_CALIB, //25 MODE_ROTARY_FRICTION_TUNING, //26 MODE_DDV_POS_VS_PWM_ID = 30, //30 MODE_DDV_DEADZONE_AND_CENTER, //31 MODE_DDV_POS_VS_FLOWRATE, //32 MODE_SYSTEM_ID, //33 MODE_FREQ_TEST, //34 MODE_SEND_BUFFER, //35 MODE_SEND_OVER, //36 MODE_STEP_TEST, //37 }; void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; /* Configure the main internal regulator output voltage */ __HAL_RCC_PWR_CLK_ENABLE(); __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); /* Initializes the CPU, AHB and APB busses clocks */ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; RCC_OscInitStruct.HSIState = RCC_HSI_ON; RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; RCC_OscInitStruct.PLL.PLLM = 8;//8 RCC_OscInitStruct.PLL.PLLN = 180; //180 RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; RCC_OscInitStruct.PLL.PLLQ = 2; RCC_OscInitStruct.PLL.PLLR = 2; if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { //Error_Handler(); } /** Activate the Over-Drive mode */ if (HAL_PWREx_EnableOverDrive() != HAL_OK) { //Error_Handler(); } /** Initializes the CPU, AHB and APB busses clocks */ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) { //Error_Handler(); } } int main() { /********************************* *** Initialization *********************************/ HAL_Init(); SystemClock_Config(); LED = 0; pc.baud(9600); // i2c init // i2c.frequency(400 * 1000); // 0.4 mHz // wait_ms(2); // Power Up wait // look_for_hardware_i2c(); // Hardware present // init_as5510(i2c_slave_addr1); // make_delay(); // spi init eeprom_cs = 1; eeprom.format(8,3); eeprom.frequency(5000000); //5M eeprom_cs = 0; make_delay(); enc_cs = 1; //sw add enc.format(8,0); enc.frequency(5000000); //10M enc_cs = 0; //sw add make_delay(); // spi _ enc spi_enc_set_init(); make_delay(); ////// bno rom // spi_eeprom_write(RID_BNO, (int16_t)1); // make_delay(); //////// // rom ROM_CALL_DATA(); make_delay(); // ADC init Init_ADC(); make_delay(); // Pwm init Init_PWM(); TIM4->CR1 ^= TIM_CR1_UDIS; make_delay(); // CAN can.attach(&CAN_RX_HANDLER); CAN_ID_INIT(); make_delay(); //can.reset(); can.filter(msg.id, 0xFFFFF000, CANStandard); // TMR3 init Init_TMR3(); TIM3->CR1 ^= TIM_CR1_UDIS; make_delay(); //Timer priority NVIC_SetPriority(TIM3_IRQn, 2); NVIC_SetPriority(TIM4_IRQn, 3); //DAC init if (SENSING_MODE == 0) { dac_1 = TORQUE_VREF / 3.3f; dac_2 = 0.0f; } else if (SENSING_MODE == 1) { if (DIR_VALVE_ENC > 0) { dac_1 = PRES_A_VREF / 3.3f; dac_2 = PRES_B_VREF / 3.3f; } else { dac_1 = PRES_B_VREF / 3.3f; dac_2 = PRES_A_VREF / 3.3f; } } make_delay(); for (int i=0; i<50; i++) { if(i%2==0) ID_index_array[i] = - i * 0.5f; else ID_index_array[i] = (i+1) * 0.5f; } /************************************ *** Program is operating! *************************************/ while(1) { // UART example // if(timer_while==100000) { // timer_while = 0; // pc.printf("%f\n", value); // } // timer_while ++; //i2c for SW valve //if(OPERATING_MODE == 5) { // read_field(i2c_slave_addr1); // if(DIR_VALVE_ENC < 0) value = 1023 - value; // } } } // Velocity feedforward for SW valve float DDV_JOINT_POS_FF(float REF_JOINT_VEL) { int i = 0; float Ref_Valve_Pos_FF = 0.0f; for(i=0; i<VALVE_POS_NUM; i++) { if(REF_JOINT_VEL >= min(JOINT_VEL[i],JOINT_VEL[i+1]) && REF_JOINT_VEL <= max(JOINT_VEL[i],JOINT_VEL[i+1])) { if(i==0) { if(JOINT_VEL[i+1] == JOINT_VEL[i]) { Ref_Valve_Pos_FF = (float) VALVE_CENTER; } else { Ref_Valve_Pos_FF = ((float) 10/(JOINT_VEL[i+1] - JOINT_VEL[i]) * (REF_JOINT_VEL - JOINT_VEL[i])) + (float) VALVE_CENTER; } } else { if(JOINT_VEL[i+1] == JOINT_VEL[i-1]) { Ref_Valve_Pos_FF = (float) VALVE_CENTER; } else { Ref_Valve_Pos_FF = ((float) 10*(ID_index_array[i+1] - ID_index_array[i-1])/(JOINT_VEL[i+1] - JOINT_VEL[i-1]) * (REF_JOINT_VEL - JOINT_VEL[i-1])) + (float) VALVE_CENTER + (float) (10*ID_index_array[i-1]); } } break; } } if(REF_JOINT_VEL > max(JOINT_VEL[VALVE_POS_NUM-1], JOINT_VEL[VALVE_POS_NUM-2])) { Ref_Valve_Pos_FF = (float) VALVE_MAX_POS; } else if(REF_JOINT_VEL < min(JOINT_VEL[VALVE_POS_NUM-1], JOINT_VEL[VALVE_POS_NUM-2])) { Ref_Valve_Pos_FF = (float) VALVE_MIN_POS; } Ref_Valve_Pos_FF = (float) VELOCITY_COMP_GAIN * 0.01f * (float) (Ref_Valve_Pos_FF - (float) VALVE_CENTER); //VELOCITY_COMP_GAIN : 0~100 return Ref_Valve_Pos_FF; } // Valve feedforward for SW valve void VALVE_POS_CONTROL(float REF_VALVE_POS) { int i = 0; if(REF_VALVE_POS > VALVE_MAX_POS) { REF_VALVE_POS = VALVE_MAX_POS; } else if(REF_VALVE_POS < VALVE_MIN_POS) { REF_VALVE_POS = VALVE_MIN_POS; } valve_pos_err = (float) (REF_VALVE_POS - value); valve_pos_err_diff = valve_pos_err - valve_pos_err_old; valve_pos_err_old = valve_pos_err; valve_pos_err_sum += valve_pos_err; if (valve_pos_err_sum > 1000.0f) valve_pos_err_sum = 1000.0f; if (valve_pos_err_sum<-1000.0f) valve_pos_err_sum = -1000.0f; VALVE_PWM_RAW_FB = P_GAIN_VALVE_POSITION * valve_pos_err + I_GAIN_VALVE_POSITION * valve_pos_err_sum + D_GAIN_VALVE_POSITION * valve_pos_err_diff; for(i=0; i<24; i++) { if(REF_VALVE_POS >= min(VALVE_POS_VS_PWM[i],VALVE_POS_VS_PWM[i+1]) && (float) REF_VALVE_POS <= max(VALVE_POS_VS_PWM[i],VALVE_POS_VS_PWM[i+1])) { if(i==0) { VALVE_PWM_RAW_FF = (float) 1000.0f / (float) (VALVE_POS_VS_PWM[i+1] - VALVE_POS_VS_PWM[i]) * ((float) REF_VALVE_POS - VALVE_POS_VS_PWM[i]); } else { VALVE_PWM_RAW_FF = (float) 1000.0f* (float) (ID_index_array[i+1] - ID_index_array[i-1])/(VALVE_POS_VS_PWM[i+1] - VALVE_POS_VS_PWM[i-1]) * ((float) REF_VALVE_POS - VALVE_POS_VS_PWM[i-1]) + 1000.0f * (float) ID_index_array[i-1]; } break; } } Vout.ref = VALVE_PWM_RAW_FF + VALVE_PWM_RAW_FB; } // PWM duty vs. voltage output of L6205 in STM board #define LT_MAX_IDX 57 float LT_PWM_duty[LT_MAX_IDX] = {-100.0f, -80.0f, -60.0f, -50.0f, -40.0f, -35.0f, -30.0f, -25.0f, -20.0f, -19.0f, -18.0f, -17.0f, -16.0f, -15.0f, -14.0f, -13.0f, -12.0f, -11.0f, -10.0f, -9.0f, -8.0f, -7.0f, -6.0f, -5.0f, -4.0f, -3.0f, -2.0f, -1.0f, 0.0f, 1.0f, 2.0f, 3.0f, 4.0f, 5.0f, 6.0f, 7.0f, 8.0f, 9.0f, 10.0f, 11.0f, 12.0f, 13.0f, 14.0f, 15.0f, 16.0f, 17.0f, 18.0f, 19.0f, 20.0f, 25.0f, 30.0f, 35.0f, 40.0f, 50.0f, 60.0f, 80.0f, 100.0f }; // duty float LT_Voltage_Output[LT_MAX_IDX] = {-230.0f, -215.0f, -192.5f, -185.0f, -177.5f, -170.0f, -164.0f, -160.0f, -150.0f, -150.0f, -145.0f, -145.0f, -145.0f, -135.0f, -135.0f, -135.0f, -127.5f, -127.5f, -115.0f, -115.0f, -115.0F, -100.0f, -100.0f, -100.0f, -60.0f, -60.0f, -10.0f, -5.0f, 0.0f, 7.5f, 14.0f, 14.0f, 14.0f, 42.5f, 42.5f, 42.5f, 80.0f, 80.0f, 105.0f, 105.0f, 105.0f, 120.0f, 120.0f, 120.0f, 131.0f, 131.0f, 140.0f, 140.0f, 140.0f, 155.0f, 160.0f, 170.0f, 174.0f, 182.0f, 191.0f, 212.0f, 230.0f }; // mV float PWM_duty_byLT(float Ref_V) { float PWM_duty = 0.0f; if(Ref_V<LT_Voltage_Output[0]) { PWM_duty = (Ref_V-LT_Voltage_Output[0])/1.5f+LT_PWM_duty[0]; } else if (Ref_V>=LT_Voltage_Output[LT_MAX_IDX-1]) { PWM_duty = (Ref_V-LT_Voltage_Output[LT_MAX_IDX-1])/1.5f+LT_PWM_duty[LT_MAX_IDX-1]; } else { int idx = 0; for(idx=0; idx<LT_MAX_IDX-1; idx++) { float ini_x = LT_Voltage_Output[idx]; float fin_x = LT_Voltage_Output[idx+1]; float ini_y = LT_PWM_duty[idx]; float fin_y = LT_PWM_duty[idx+1]; if(Ref_V>=ini_x && Ref_V<fin_x) { PWM_duty = (fin_y-ini_y)/(fin_x-ini_x)*(Ref_V-ini_x) + ini_y; break; } } } return PWM_duty; } /******************************************************************************* TIMER INTERRUPT *******************************************************************************/ float FREQ_TMR4 = (float)FREQ_20k; float DT_TMR4 = (float)DT_20k; long CNT_TMR4 = 0; int TMR4_FREQ_10k = (int)FREQ_10k; extern "C" void TIM4_IRQHandler(void) { if (TIM4->SR & TIM_SR_UIF ) { /******************************************************* *** Sensor Read & Data Handling ********************************************************/ //Encoder if (CNT_TMR4 % (int) ((int) FREQ_TMR4/TMR4_FREQ_10k) == 0) { ENC_UPDATE(); } ADC1->CR2 |= 0x40000000; // Torque Sensing ============================================= if (SENSING_MODE == 0) { float pres_A_new = (((float) ADC1->DR) - 2047.5f); double alpha_update_ft = 1.0f / (1.0f + FREQ_TMR4 / (2.0f * 3.14f * 100.0f)); // f_cutoff : 100Hz pres_A.sen = (1.0f - alpha_update_ft) * pres_A.sen + alpha_update_ft * pres_A_new; torq.sen = -pres_A.sen / TORQUE_SENSOR_PULSE_PER_TORQUE; // Pressure Sensing (0~210)bar ============================================= } else if (SENSING_MODE == 1) { if (DIR_VALVE_ENC > 0) { pres_A_new = (((float)ADC1->DR) - PRES_A_NULL); pres_B_new = (((float)ADC2->DR) - PRES_B_NULL); } else { pres_A_new = (((float)ADC2->DR) - PRES_A_NULL); pres_B_new = (((float)ADC1->DR) - PRES_B_NULL); } double alpha_update_pres = 1.0f / (1.0f + FREQ_TMR4 / (2.0f * 3.14f * 200.0f)); // f_cutoff : 200Hz pres_A.sen = (1.0f - alpha_update_pres) * pres_A.sen + alpha_update_pres * pres_A_new; pres_B.sen = (1.0f - alpha_update_pres) * pres_B.sen + alpha_update_pres * pres_B_new; CUR_PRES_A_BAR = pres_A.sen / PRES_SENSOR_A_PULSE_PER_BAR; CUR_PRES_B_BAR = pres_B.sen / PRES_SENSOR_B_PULSE_PER_BAR; if ((OPERATING_MODE & 0x01) == 0) { // Rotary Actuator torq.sen = (PISTON_AREA_A * CUR_PRES_A_BAR - PISTON_AREA_B * CUR_PRES_B_BAR) * 0.0001f; // mm^3*bar >> Nm } else if ((OPERATING_MODE & 0x01) == 1) { // Linear Actuator torq.sen = (PISTON_AREA_A * CUR_PRES_A_BAR - PISTON_AREA_B * CUR_PRES_B_BAR) * 0.1f; // mm^2*bar >> N } } //Current //ADC3->CR2 |= 0x40000000; // adc _ 12bit float alpha_update_cur = 1.0f/(1.0f + FREQ_TMR4/(2.0f*3.14f*500.0f)); // f_cutoff : 500Hz float cur_new = ((float)ADC3->DR-2048.0f)*20.0f/4096.0f; // unit : mA cur.sen=cur.sen*(1.0f-alpha_update_cur)+cur_new*(alpha_update_cur); CNT_TMR4++; } TIM4->SR = 0x0; // reset the status register } int j =0; float FREQ_TMR3 = (float)FREQ_5k; float DT_TMR3 = (float)DT_5k; int cnt_trans = 0; double VALVE_POS_RAW_FORCE_FB_LOGGING = 0.0f; int can_rest =0; extern "C" void TIM3_IRQHandler(void) { if (TIM3->SR & TIM_SR_UIF ) { if (((OPERATING_MODE&0b110)>>1) == 0) { K_v = 0.4f; // Moog (LPM >> mA) , 100bar mV_PER_mA = 500.0f; // 5000mV/10mA mV_PER_pulse = 0.5f; // 5000mV/10000pulse mA_PER_pulse = 0.001f; // 10mA/10000pulse } else if (((OPERATING_MODE&0b110)>>1) == 1) { K_v = 0.5f; // KNR (LPM >> mA) , 100bar mV_PER_mA = 166.6666f; // 5000mV/30mA mV_PER_pulse = 0.5f; // 5000mV/10000pulse mA_PER_pulse = 0.003f; // 30mA/10000pulse } if(MODE_POS_FT_TRANS == 1) { alpha_trans = (float)(1.0f - cos(3.141592f * (float)cnt_trans * DT_TMR3 /3.0f))/2.0f; cnt_trans++; torq.err_sum = 0; if((float)cnt_trans * DT_TMR3 > 3.0f) MODE_POS_FT_TRANS = 2; } else if(MODE_POS_FT_TRANS == 3) { alpha_trans = (float)(1.0f + cos(3.141592f * (float)cnt_trans * DT_TMR3 /3.0f))/2.0f; cnt_trans++; torq.err_sum = 0; if((float) cnt_trans * DT_TMR3 > 3.0f ) MODE_POS_FT_TRANS = 0; } else if(MODE_POS_FT_TRANS == 2) { alpha_trans = 1.0f; cnt_trans = 0; } else { alpha_trans = 0.0f; cnt_trans = 0; } // Reference Loop ========================================================== switch (REFERENCE_MODE) { case MODE_REF_NO_ACT: { break; } case MODE_REF_DIRECT: { pos.ref = REF_POSITION; vel.ref = REF_VELOCITY; torq.ref = REF_TORQUE; break; } default: break; } int UTILITY_MODE = 0; int CONTROL_MODE = 0; if (CONTROL_UTILITY_MODE >= 20 || CONTROL_UTILITY_MODE == 0) { UTILITY_MODE = CONTROL_UTILITY_MODE; CONTROL_MODE = MODE_NO_ACT; } else { CONTROL_MODE = CONTROL_UTILITY_MODE; UTILITY_MODE = MODE_NO_ACT; } // UTILITY MODE ------------------------------------------------------------ switch (UTILITY_MODE) { case MODE_NO_ACT: { break; } case MODE_TORQUE_SENSOR_NULLING: { // DAC Voltage reference set if (TMR3_COUNT_TORQUE_NULL < TMR_FREQ_5k * 2) { CUR_TORQUE_sum += torq.sen; if (TMR3_COUNT_TORQUE_NULL % 10 == 0) { CUR_TORQUE_mean = CUR_TORQUE_sum / 10.0f; CUR_TORQUE_sum = 0; TORQUE_VREF += 0.000003f * (0.0f - CUR_TORQUE_mean); if (TORQUE_VREF > 3.3f) TORQUE_VREF = 3.3f; if (TORQUE_VREF < 0.0f) TORQUE_VREF = 0.0f; dac_1 = TORQUE_VREF / 3.3f; } } else { CONTROL_UTILITY_MODE = MODE_NO_ACT; TMR3_COUNT_TORQUE_NULL = 0; CUR_TORQUE_sum = 0; CUR_TORQUE_mean = 0; spi_eeprom_write(RID_TORQUE_SENSOR_VREF, (int16_t) (TORQUE_VREF * 1000.0f)); dac_1 = TORQUE_VREF / 3.3f; } TMR3_COUNT_TORQUE_NULL++; break; } case MODE_FIND_HOME: { if (FINDHOME_STAGE == FINDHOME_INIT) { REFERENCE_MODE=MODE_REF_NO_ACT; cnt_findhome = 0; cnt_vel_findhome = 0; pos.ref = pos.sen; vel.ref = 0.0f; FINDHOME_STAGE = FINDHOME_GOTOLIMIT; } else if (FINDHOME_STAGE == FINDHOME_GOTOLIMIT) { int cnt_check_enc = (TMR_FREQ_5k/20); if(cnt_findhome%cnt_check_enc == 0) { FINDHOME_POSITION = pos.sen; FINDHOME_VELOCITY = FINDHOME_POSITION - FINDHOME_POSITION_OLD; FINDHOME_POSITION_OLD = FINDHOME_POSITION; } cnt_findhome++; if (abs(FINDHOME_VELOCITY) <= 1) { cnt_vel_findhome = cnt_vel_findhome + 1; } else { cnt_vel_findhome = 0; } if ((cnt_vel_findhome < 3*TMR_FREQ_5k) && cnt_findhome < 10*TMR_FREQ_5k) { // wait for 3sec if (HOMEPOS_OFFSET > 0) { pos.ref = pos.ref + 12.0f; } else { pos.ref = pos.ref - 12.0f; } CONTROL_MODE = MODE_JOINT_CONTROL; alpha_trans = 0.0f; } else { ENC_SET((int32_t)((int32_t)HOMEPOS_OFFSET*10)); INIT_REF_POS = (int32_t)((int32_t)HOMEPOS_OFFSET*10); REF_POSITION = 0; REF_VELOCITY = 0; FINDHOME_POSITION = 0; FINDHOME_POSITION_OLD = 0; FINDHOME_VELOCITY = 0; cnt_findhome = 0; cnt_vel_findhome = 0; FINDHOME_STAGE = FINDHOME_ZEROPOSE; cnt_findhome = 0; pos.ref = 0.0f; vel.ref = 0.0f; pos.ref_home_pos = 0.0f; vel.ref_home_pos = 0.0f; } } else if (FINDHOME_STAGE == FINDHOME_ZEROPOSE) { int T_move = 2*TMR_FREQ_5k; pos.ref = (0.0f - (float)INIT_REF_POS)*0.5f*(1.0f - cos(3.14159f * (float)cnt_findhome / (float)T_move)) + (float)INIT_REF_POS; vel.ref = 0.0f; alpha_trans = 0.0f; pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm] vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s] pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm] CONTROL_MODE = MODE_JOINT_CONTROL; cnt_findhome++; if (cnt_findhome >= T_move) { cnt_findhome = 0; pos.ref = 0.0f; vel.ref = 0.0f; pos.ref_home_pos = 0.0f; vel.ref_home_pos = 0.0f; FINDHOME_STAGE = FINDHOME_INIT; CONTROL_UTILITY_MODE = MODE_JOINT_CONTROL; REFERENCE_MODE=MODE_REF_DIRECT; } } break; } case MODE_PRESSURE_SENSOR_NULLING: { // DAC Voltage reference set if (TMR3_COUNT_PRES_NULL < TMR_FREQ_5k * 2) { CUR_PRES_A_sum += pres_A.sen; CUR_PRES_B_sum += pres_B.sen; if (TMR3_COUNT_PRES_NULL % 10 == 0) { CUR_PRES_A_mean = CUR_PRES_A_sum / 10.0f; CUR_PRES_B_mean = CUR_PRES_B_sum / 10.0f; CUR_PRES_A_sum = 0; CUR_PRES_B_sum = 0; float VREF_NullingGain = 0.0003f; PRES_A_VREF = PRES_A_VREF + VREF_NullingGain * CUR_PRES_A_mean; PRES_B_VREF = PRES_B_VREF + VREF_NullingGain * CUR_PRES_B_mean; if (PRES_A_VREF > 3.3f) PRES_A_VREF = 3.3f; if (PRES_A_VREF < 0.0f) PRES_A_VREF = 0.0f; if (PRES_B_VREF > 3.3f) PRES_B_VREF = 3.3f; if (PRES_B_VREF < 0.0f) PRES_B_VREF = 0.0f; if (DIR_VALVE_ENC > 0) { dac_1 = PRES_A_VREF / 3.3f; dac_2 = PRES_B_VREF / 3.3f; } else { dac_1 = PRES_B_VREF / 3.3f; dac_2 = PRES_A_VREF / 3.3f; } } } else { CONTROL_UTILITY_MODE = MODE_NO_ACT; TMR3_COUNT_PRES_NULL = 0; CUR_PRES_A_sum = 0; CUR_PRES_B_sum = 0; CUR_PRES_A_mean = 0; CUR_PRES_B_mean = 0; spi_eeprom_write(RID_PRES_A_SENSOR_VREF, (int16_t) (PRES_A_VREF * 1000.0f)); spi_eeprom_write(RID_PRES_B_SENSOR_VREF, (int16_t) (PRES_B_VREF * 1000.0f)); if (DIR_VALVE_ENC > 0) { dac_1 = PRES_A_VREF / 3.3f; dac_2 = PRES_B_VREF / 3.3f; } else { dac_1 = PRES_B_VREF / 3.3f; dac_2 = PRES_A_VREF / 3.3f; } } TMR3_COUNT_PRES_NULL++; break; } case MODE_DDV_DEADZONE_AND_CENTER: { if (FINDDZ_STAGE == FINDDZ_INIT) { cnt_finddz = 0; cnt_vel_finddz = 0; temp_pos_ref = pos.sen; temp_pos_ref_offset = 0.0f; vel.ref = 0.0f; FINDDZ_STAGE = FINDDZ_START1; flag_finddz = 1; FINDDZ_POSITION = pos.sen; FINDDZ_POSITION_OLD = FINDDZ_POSITION; temp_P_GAIN = P_GAIN_JOINT_POSITION; temp_I_GAIN = I_GAIN_JOINT_POSITION; temp_VELOCITY_COMP_GAIN = VELOCITY_COMP_GAIN; P_GAIN_JOINT_POSITION = 1.0f; I_GAIN_JOINT_POSITION = 0.0f; VELOCITY_COMP_GAIN = 0; FLAG_VALVE_DEADZONE = 0; alpha_trans = 0.0f; REFERENCE_MODE=MODE_REF_NO_ACT; } else if (FINDDZ_STAGE == FINDDZ_START1) { cnt_finddz++; CONTROL_MODE = MODE_JOINT_CONTROL; FINDDZ_POSITION = pos.sen; FINDDZ_VELOCITY = FINDDZ_POSITION - FINDDZ_POSITION_OLD; FINDDZ_POSITION_OLD = FINDDZ_POSITION; if (temp_P_GAIN > 0.0f) temp_pos_ref_offset = temp_pos_ref_offset - (float)FINDDZ_VELOCITY*temp_P_GAIN; else temp_pos_ref_offset = temp_pos_ref_offset - (float)FINDDZ_VELOCITY*20.0f; pos.ref = temp_pos_ref + temp_pos_ref_offset; if (cnt_finddz > 10000) FINDDZ_STAGE = FINDDZ_START2; } else if (FINDDZ_STAGE == FINDDZ_START2) { CONTROL_MODE = MODE_JOINT_CONTROL; FINDDZ_POSITION = pos.sen; FINDDZ_VELOCITY = FINDDZ_POSITION - FINDDZ_POSITION_OLD; FINDDZ_POSITION_OLD = FINDDZ_POSITION; if (flag_finddz > 0) { temp_pos_ref = temp_pos_ref + 1.0f; if (FINDDZ_VELOCITY > 0) { cnt_vel_finddz = cnt_vel_finddz + 1; } if (cnt_vel_finddz > 5) { VALVE_DEADZONE_PLUS = (int)(I_REF_fil/mA_PER_pulse); // temp_VALVE_DEADZONE_PLUS = temp_VALVE_DEADZONE_PLUS + I_REF_fil/mA_PER_pulse; cnt_vel_finddz = 0; flag_finddz = - flag_finddz - 1; } } else if (flag_finddz < 0) { temp_pos_ref = temp_pos_ref - 1.0f; if (FINDDZ_VELOCITY < 0) { cnt_vel_finddz = cnt_vel_finddz + 1; } if (cnt_vel_finddz > 5) { VALVE_DEADZONE_MINUS = (int)(I_REF_fil/mA_PER_pulse); // temp_VALVE_DEADZONE_MINUS = temp_VALVE_DEADZONE_MINUS + I_REF_fil/mA_PER_pulse; cnt_vel_finddz = 0; flag_finddz = - flag_finddz + 1; } } if (abs(flag_finddz) >= 6) { FINDDZ_STAGE = FINDDZ_STOP; // VALVE_DEADZONE_PLUS = (int)(temp_VALVE_DEADZONE_PLUS / (double)flag_finddz * 2.0f); // VALVE_DEADZONE_MINUS = (int)(temp_VALVE_DEADZONE_MINUS / (double)flag_finddz * 2.0f); spi_eeprom_write(RID_VALVE_DEADZONE_PLUS, VALVE_DEADZONE_PLUS); spi_eeprom_write(RID_VALVE_DEADZONE_MINUS, VALVE_DEADZONE_MINUS); } pos.ref = temp_pos_ref + temp_pos_ref_offset; } else if (FINDDZ_STAGE == FINDDZ_STOP) { FINDDZ_STAGE = FINDDZ_INIT; CONTROL_UTILITY_MODE = MODE_JOINT_CONTROL; P_GAIN_JOINT_POSITION = temp_P_GAIN; I_GAIN_JOINT_POSITION = temp_I_GAIN; VELOCITY_COMP_GAIN = temp_VELOCITY_COMP_GAIN; flag_finddz = 0; FLAG_VALVE_DEADZONE = 1; REFERENCE_MODE=MODE_REF_DIRECT; } break; } case MODE_SYSTEM_ID: { freq_sysid_Iref = (double) cnt_sysid * DT_TMR3 * 3.0f; valve_pos.ref = 2500.0f * sin(2.0f * 3.14159f * freq_sysid_Iref * (double) cnt_sysid * DT_TMR3); CONTROL_MODE = MODE_VALVE_OPEN_LOOP; cnt_sysid++; if (freq_sysid_Iref >= 300) { cnt_sysid = 0; CONTROL_UTILITY_MODE = MODE_NO_ACT; } break; } case MODE_FREQ_TEST: { float valve_pos_ref = 2500.0f * sin(2.0f * 3.141592f * freq_test_valve_ref * (float) cnt_freq_test * DT_TMR3); if(valve_pos_ref >= 0) { valve_pos.ref = (double)VALVE_CENTER + (double)valve_pos_ref * ((double)VALVE_MAX_POS-(double)VALVE_CENTER)/10000.0f; } else { valve_pos.ref = (double)VALVE_CENTER - (double)valve_pos_ref * ((double)VALVE_MIN_POS-(double)VALVE_CENTER)/10000.0f; } ref_array[cnt_freq_test] = valve_pos_ref; if(value>=(float) VALVE_CENTER) { pos_array[cnt_freq_test] = 10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER); } else { pos_array[cnt_freq_test] = -10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER); } CONTROL_MODE = MODE_VALVE_POSITION_CONTROL; cnt_freq_test++; if (freq_test_valve_ref * (float) cnt_freq_test * DT_TMR3 > 2) { buffer_data_size = cnt_freq_test; cnt_freq_test = 0; cnt_send_buffer = 0; freq_test_valve_ref = freq_test_valve_ref * 1.05f; if (freq_test_valve_ref >= 400) { CONTROL_UTILITY_MODE = MODE_NO_ACT; CONTROL_MODE = MODE_NO_ACT; CAN_TX_PWM((int16_t) (1)); //1300 } CONTROL_MODE = MODE_NO_ACT; CONTROL_UTILITY_MODE = MODE_SEND_OVER; } break; } case MODE_STEP_TEST: { float valve_pos_ref = 0.0f; if (cnt_step_test < (int) (1.0f * (float) TMR_FREQ_5k)) { valve_pos_ref = 0.0f; } else { valve_pos_ref = 10000.0f; } if(valve_pos_ref >= 0) { valve_pos.ref = (double)VALVE_CENTER + (double)valve_pos_ref * ((double)VALVE_MAX_POS-(double)VALVE_CENTER)/10000.0f; } else { valve_pos.ref = (double)VALVE_CENTER - (double)valve_pos_ref * ((double)VALVE_MIN_POS-(double)VALVE_CENTER)/10000.0f; } ref_array[cnt_step_test] = valve_pos_ref; if(value>=(float) VALVE_CENTER) { pos_array[cnt_step_test] = 10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER); } else { pos_array[cnt_step_test] = -10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER); } CONTROL_MODE = MODE_VALVE_POSITION_CONTROL; cnt_step_test++; if (cnt_step_test > (int) (2.0f * (float) TMR_FREQ_5k)) { buffer_data_size = cnt_step_test; cnt_step_test = 0; cnt_send_buffer = 0; CONTROL_UTILITY_MODE = MODE_SEND_OVER; CONTROL_MODE = MODE_NO_ACT; } break; } default: break; } // CONTROL MODE ------------------------------------------------------------ switch (CONTROL_MODE) { case MODE_NO_ACT: { V_out = 0.0f; break; } case MODE_VALVE_POSITION_CONTROL: { if (OPERATING_MODE == 5) { //SW Valve VALVE_POS_CONTROL(valve_pos.ref); V_out = Vout.ref; } else if (CURRENT_CONTROL_MODE == 0) { //PWM V_out = valve_pos.ref; } else { I_REF = valve_pos.ref * 0.001f; } break; } case MODE_JOINT_CONTROL: { double torq_ref = 0.0f; pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm] vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s] pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm] //K & D Low Pass Filter float alpha_K_D = 1.0f/(1.0f + 5000.0f/(2.0f*3.14f*30.0f)); // f_cutoff : 30Hz K_LPF = K_LPF*(1.0f-alpha_K_D)+K_SPRING*(alpha_K_D); D_LPF = D_LPF*(1.0f-alpha_K_D)+D_DAMPER*(alpha_K_D); torq_ref = torq.ref + K_LPF * pos.err - D_LPF * vel.sen / ENC_PULSE_PER_POSITION; //[N] // torque feedback torq.err = torq_ref - torq.sen; //[N] torq.err_sum += torq.err/(float) TMR_FREQ_5k; //[N] if (((OPERATING_MODE&0b110)>>1) == 0 || ((OPERATING_MODE&0b110)>>1) == 1) { double I_REF_POS = 0.0f; double I_REF_FORCE_FB = 0.0f; // I_REF by Force Feedback double I_REF_VC = 0.0f; // I_REF for velocity compensation double temp_vel_pos = 0.0f; double temp_vel_torq = 0.0f; double wn_Pos = 2.0f * PI * 5.0f; // f_cut : 5Hz Position Control if ((OPERATING_MODE & 0x01) == 0) { // Rotary Mode temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION) * PI / 180.0f; // rad/s // L when P-gain = 100, f_cut = 10Hz L feedforward velocity } else if ((OPERATING_MODE & 0x01) == 1) { temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION); // mm/s // L when P-gain = 100, f_cut = 10Hz L feedforward velocity } if (temp_vel_pos > 0.0f) I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_A * 0.00006f / (K_v * sqrt(2.0f * alpha3 / (alpha3 + 1.0f)))); else I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_B * 0.00006f / (K_v * sqrt(2.0f / (alpha3 + 1.0f)))); // velocity compensation for torque control if ((OPERATING_MODE & 0x01) == 0) { // Rotary Mode I_REF_FORCE_FB = 0.001f * ((double) P_GAIN_JOINT_TORQUE * torq.err + (double) I_GAIN_JOINT_TORQUE * torq.err_sum); // temp_vel_torq = (0.01 * (double) VELOCITY_COMP_GAIN * (double) CUR_VELOCITY / (double) ENC_PULSE_PER_POSITION) * PI / 180.0; // rad/s temp_vel_torq = (0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / (double) ENC_PULSE_PER_POSITION) * PI / 180.0f; // rad/s // L feedforward velocity } else if ((OPERATING_MODE & 0x01) == 1) { I_REF_FORCE_FB = 0.001f * 0.01f*((double) P_GAIN_JOINT_TORQUE * torq.err + (double) I_GAIN_JOINT_TORQUE * torq.err_sum); // Linear Actuators are more sensitive. // temp_vel_torq = (0.01 * (double) VELOCITY_COMP_GAIN * (double) CUR_VELOCITY / (double) ENC_PULSE_PER_POSITION); // mm/s temp_vel_torq = (0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / (double) ENC_PULSE_PER_POSITION); // mm/s // L feedforward velocity } if (temp_vel_torq > 0.0f) I_REF_VC = temp_vel_torq * ((double) PISTON_AREA_A * 0.00006f / (K_v * sqrt(2.0f * alpha3 / (alpha3 + 1.0f)))); else I_REF_VC = temp_vel_torq * ((double) PISTON_AREA_B * 0.00006f / (K_v * sqrt(2.0f / (alpha3 + 1.0f)))); // L velocity(rad/s or mm/s) >> I_ref(mA) // Ref_Joint_FT_dot = (Ref_Joint_FT_Nm - Ref_Joint_FT_Nm_old) / TMR_DT_5k; // Ref_Joint_FT_Nm_old = Ref_Joint_FT_Nm; I_REF = (1.0f - alpha_trans) * I_REF_POS + alpha_trans * (I_REF_VC + I_REF_FORCE_FB); // Anti-windup for FT if (I_GAIN_JOINT_TORQUE != 0) { double I_MAX = 10.0f; // Maximum Current : 10mV double Ka = 2.0f / ((double) I_GAIN_JOINT_TORQUE * 0.001f); if (I_REF > I_MAX) { double I_rem = I_REF - I_MAX; I_rem = Ka*I_rem; I_REF = I_MAX; torq.err_sum = torq.err_sum - I_rem /(float) TMR_FREQ_5k; } else if (I_REF < -I_MAX) { double I_rem = I_REF - (-I_MAX); I_rem = Ka*I_rem; I_REF = -I_MAX; torq.err_sum = torq.err_sum - I_rem /(float) TMR_FREQ_5k; } } } else { float VALVE_POS_RAW_FORCE_FB = 0.0f; float VALVE_POS_RAW_FORCE_FF = 0.0f; float VALVE_POS_RAW = 0.0f; VALVE_POS_RAW_FORCE_FB = alpha_trans*(((float) P_GAIN_JOINT_TORQUE * torq.err + (float) I_GAIN_JOINT_TORQUE * torq.err_sum + (float) D_GAIN_JOINT_TORQUE * (torq.ref_diff - torq_dot.sen)) * 0.01f + DDV_JOINT_POS_FF(vel.sen))+ (1.0f-alpha_trans) * (P_GAIN_JOINT_POSITION * 0.01f * pos.err + DDV_JOINT_POS_FF(vel.ref)); VALVE_POS_RAW_FORCE_FF = P_GAIN_JOINT_TORQUE_FF * torq_ref * 0.001f + D_GAIN_JOINT_TORQUE_FF * (torq_ref - torq_ref_past) * 0.0001f; VALVE_POS_RAW = VALVE_POS_RAW_FORCE_FB + VALVE_POS_RAW_FORCE_FF; if (VALVE_POS_RAW >= 0) { valve_pos.ref = VALVE_POS_RAW + VALVE_DEADZONE_PLUS; } else { valve_pos.ref = VALVE_POS_RAW + VALVE_DEADZONE_MINUS; } if(I_GAIN_JOINT_TORQUE != 0) { double Ka = 2.0f / (double) I_GAIN_JOINT_TORQUE * 100.0f; if(valve_pos.ref>VALVE_MAX_POS) { double valve_pos_rem = valve_pos.ref - VALVE_MAX_POS; valve_pos_rem = valve_pos_rem * Ka; valve_pos.ref = VALVE_MAX_POS; torq.err_sum = torq.err_sum - valve_pos_rem/(float) TMR_FREQ_5k; } else if(valve_pos.ref < VALVE_MIN_POS) { double valve_pos_rem = valve_pos.ref - VALVE_MIN_POS; valve_pos_rem = valve_pos_rem * Ka; valve_pos.ref = VALVE_MIN_POS; torq.err_sum = torq.err_sum - valve_pos_rem/(float) TMR_FREQ_5k; } } VALVE_POS_CONTROL(valve_pos.ref); V_out = (float) Vout.ref; } torq_ref_past = torq_ref; break; } case MODE_VALVE_OPEN_LOOP: { V_out = (float) Vout.ref; break; } case MODE_JOINT_ADAPTIVE_BACKSTEPPING: { float Va = (1256.6f + Amm * pos.sen/(float)(ENC_PULSE_PER_POSITION)) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * x, unit : m^3 float Vb = (1256.6f + Amm * (79.0f - pos.sen/(float)(ENC_PULSE_PER_POSITION))) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * (79.0mm-x), unit : m^3 V_adapt = 1.0f / (1.0f/Va + 1.0f/Vb); //initial 0.0000053f //float f3 = -Amm*Amm*beta*0.000001f*0.000001f/V_adapt * vel.sen/(float)(ENC_PULSE_PER_POSITION)*0.001f; // unit : N/s //xdot=10mm/s일때 -137076 float f3_hat = -a_hat * vel.sen/(float)(ENC_PULSE_PER_POSITION)*0.001f; // unit : N/s //xdot=10mm/s일때 -137076 float g3_prime = 0.0f; if (torq.sen > Amm*(Ps-Pt)*0.000001f) { g3_prime = 1.0f; } else if (torq.sen < -Amm*(Ps-Pt)*0.000001f) { g3_prime = -1.0f; } else { if ((value-VALVE_CENTER) > 0) { g3_prime = sqrt(Ps-Pt-torq.sen/Amm*1000000.0f); // g3_prime = sqrt(Ps-Pt); } else { g3_prime = sqrt(Ps-Pt+torq.sen/Amm*1000000.0f); // g3_prime = sqrt(Ps-Pt); } } float tau = 0.01f; float K_valve = 0.0004f; float x_v = 0.0f; //x_v : -1~1 if(value>=VALVE_CENTER) { x_v = 1.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER); } else { x_v = -1.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER); } float f4 = -x_v/tau; float g4 = K_valve/tau; float torq_ref_dot = torq.ref_diff * 500.0f; pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm] vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s] pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm] torq.err = torq.ref - torq.sen; //[N] torq.err_sum += torq.err/(float) TMR_FREQ_5k; //[N] float k3 = 2000.0f; //2000 //20000 float k4 = 10.0f; float rho3 = 3.2f; float rho4 = 10000000.0f; //25000000.0f; float x_4_des = (-f3_hat + torq_ref_dot - k3*(-torq.err))/(gamma_hat*g3_prime); if (x_4_des > 1) x_4_des = 1; else if (x_4_des < -1) x_4_des = -1; if (x_4_des > 0) { valve_pos.ref = x_4_des * (float)(VALVE_MAX_POS - VALVE_CENTER) + (float) VALVE_CENTER; } else { valve_pos.ref = x_4_des * (float)(VALVE_CENTER - VALVE_MIN_POS) + (float) VALVE_CENTER; } float x_4_des_dot = (x_4_des - x_4_des_old)*(float) TMR_FREQ_5k; x_4_des_old = x_4_des; V_out = (-f4 + x_4_des_dot - k4*(x_v-x_4_des)- rho3/rho4*gamma_hat*g3_prime*(-torq.err))/g4; float rho_a = 0.00001f; float a_hat_dot = -rho3/rho_a*vel.sen/(float)(ENC_PULSE_PER_POSITION)*0.001f*(-torq.err); a_hat = a_hat + a_hat_dot / (float) TMR_FREQ_5k; if(a_hat > -3000000.0f) a_hat = -3000000.0f; else if(a_hat < -30000000.0f) a_hat = -30000000.0f; break; } default: break; } if (((OPERATING_MODE&0b110)>>1) == 0 || ((OPERATING_MODE&0b110)>>1) == 1) { //Moog Valve or KNR Valve //////////////////////////////////////////////////////////////////////////// //////////////////////////// CURRENT CONTROL ////////////////////////////// //////////////////////////////////////////////////////////////////////////// if (CURRENT_CONTROL_MODE) { double alpha_update_Iref = 1.0f / (1.0f + 5000.0f / (2.0f * 3.14f * 300.0f)); // f_cutoff : 500Hz I_REF_fil = (1.0f - alpha_update_Iref) * I_REF_fil + alpha_update_Iref*I_REF; if (FLAG_VALVE_DEADZONE) { if (I_REF_fil > 0.0f) I_REF_fil_DZ = I_REF_fil + (double)VALVE_DEADZONE_PLUS*mA_PER_pulse; // unit: mA else if (I_REF_fil < 0.0f) I_REF_fil_DZ = I_REF_fil + (double)VALVE_DEADZONE_MINUS*mA_PER_pulse; // unit: mA else I_REF_fil_DZ = I_REF_fil + (double)(VALVE_DEADZONE_PLUS+VALVE_DEADZONE_MINUS)/2.0f*mA_PER_pulse; // unit: mA } else { I_REF_fil_DZ = I_REF_fil; } I_ERR = I_REF_fil_DZ - (double)cur.sen; I_ERR_INT = I_ERR_INT + (I_ERR) * 0.0002f; // Moog Valve Current Control Gain double R_model = 500.0f; // ohm double L_model = 1.2f; double w0 = 2.0f * 3.14f * 150.0f; double KP_I = 0.1f * L_model*w0; double KI_I = 0.1f * R_model*w0; // KNR Valve Current Control Gain if (((OPERATING_MODE & 0b110)>>1) == 1) { // KNR Valve R_model = 163.0f; // ohm L_model = 1.0f; w0 = 2.0f * 3.14f * 80.0f; KP_I = 1.0f * L_model*w0; KI_I = 0.08f * R_model*w0; } double FF_gain = 1.0f; VALVE_PWM_RAW = KP_I * 2.0f * I_ERR + KI_I * 2.0f* I_ERR_INT; I_REF_fil_diff = I_REF_fil_DZ - I_REF_fil_old; I_REF_fil_old = I_REF_fil_DZ; // VALVE_PWM_RAW = VALVE_PWM_RAW + FF_gain * (R_model * I_REF_fil + L_model * I_REF_fil_diff * 5000.0f); // Unit : mV VALVE_PWM_RAW = VALVE_PWM_RAW + FF_gain * (R_model * I_REF_fil_DZ); // Unit : mV double V_MAX = 12000.0f; // Maximum Voltage : 12V = 12000mV double Ka = 3.0f / KP_I; if (VALVE_PWM_RAW > V_MAX) { V_rem = VALVE_PWM_RAW - V_MAX; V_rem = Ka*V_rem; VALVE_PWM_RAW = V_MAX; I_ERR_INT = I_ERR_INT - V_rem * 0.0002f; } else if (VALVE_PWM_RAW < -V_MAX) { V_rem = VALVE_PWM_RAW - (-V_MAX); V_rem = Ka*V_rem; VALVE_PWM_RAW = -V_MAX; I_ERR_INT = I_ERR_INT - V_rem * 0.0002f; } Cur_Valve_Open_pulse = cur.sen / mA_PER_pulse; } else { VALVE_PWM_RAW = I_REF * mV_PER_mA; Cur_Valve_Open_pulse = I_REF / mA_PER_pulse; } //////////////////////////////////////////////////////////////////////////// ///////////////// Dead Zone Cancellation & Linearization ////////////////// //////////////////////////////////////////////////////////////////////////// // Output Voltage Linearization double CUR_PWM_nonlin = (double)VALVE_PWM_RAW; // Unit : mV double CUR_PWM_lin = PWM_duty_byLT(CUR_PWM_nonlin); // -8000~8000 // Dead Zone Cancellation (Electrical dead-zone) if (CUR_PWM_lin > 0) V_out = (float) (CUR_PWM_lin + 169.0f); else if (CUR_PWM_lin < 0) V_out = (float) (CUR_PWM_lin - 174.0f); else V_out = (float) (CUR_PWM_lin); } else { //////////////////////////sw valve // Output Voltage Linearization & Dead Zone Cancellation (Electrical dead-zone) by SW if (V_out > 0 ) V_out = (V_out + 180.0f)/0.8588f; else if (V_out < 0) V_out = (V_out - 200.0f)/0.8651f; else V_out = 0.0f; } /******************************************************* *** PWM ********************************************************/ if(DIR_VALVE<0) { V_out = -V_out; } if (V_out >= VALVE_VOLTAGE_LIMIT*1000.0f) { V_out = VALVE_VOLTAGE_LIMIT*1000.0f; } else if(V_out<=-VALVE_VOLTAGE_LIMIT*1000.0f) { V_out = -VALVE_VOLTAGE_LIMIT*1000.0f; } PWM_out= V_out/(SUPPLY_VOLTAGE*1000.0f); // Saturation of output voltage if(PWM_out > 1.0f) PWM_out=1.0f; else if (PWM_out < -1.0f) PWM_out=-1.0f; if (PWM_out>0.0f) { dtc_v=0.0f; dtc_w=PWM_out; } else { dtc_v=-PWM_out; dtc_w=0.0f; } //pwm TIM4->CCR2 = (PWM_ARR)*(1.0f-dtc_v); TIM4->CCR1 = (PWM_ARR)*(1.0f-dtc_w); if (TMR2_COUNT_CAN_TX % (int) ((int) TMR_FREQ_5k/CAN_FREQ) == 0) { // Position, Velocity, and Torque (ID:1200) if (flag_data_request[0] == HIGH) { if ((OPERATING_MODE & 0b01) == 0) { // Rotary Actuator if (SENSING_MODE == 0) { CAN_TX_POSITION_FT((int16_t) (pos.sen), (int16_t) (vel.sen/10.0f), (int16_t) (torq.sen*10.0f)); } else if (SENSING_MODE == 1) { CAN_TX_POSITION_PRESSURE((int16_t) (pos.sen), (int16_t) (vel.sen/10.0f), (int16_t) ((pres_A.sen)*5.0f), (int16_t) ((pres_B.sen)*5.0f)); } } else if ((OPERATING_MODE & 0b01) == 1) { // Linear Actuator if (SENSING_MODE == 0) { CAN_TX_POSITION_FT((int16_t) (pos.sen/10.0f), (int16_t) (vel.sen/256.0f), (int16_t) (torq.sen * 10.0f * (float)(TORQUE_SENSOR_PULSE_PER_TORQUE))); } else if (SENSING_MODE == 1) { CAN_TX_POSITION_PRESSURE((int16_t) (pos.sen/10.0f), (int16_t) (vel.sen/256.0f), (int16_t) ((pres_A.sen)*5.0f), (int16_t) ((pres_B.sen)*5.0f)); } } } // PWM, ID:1300 if (flag_data_request[1] == HIGH) { CAN_TX_PWM((int16_t) (V_out)); //1300 } // Reference Current, Current Current (ID:1400) if (flag_data_request[2] == HIGH) { CAN_TX_CURRENT((int16_t) (I_REF_fil_DZ / mA_PER_pulse), (int16_t) (cur.sen / mA_PER_pulse)); // 1400 } // Reference Current, Current Current (ID:1700) if (flag_data_request[3] == HIGH) { CAN_TX_SOMETHING((int16_t) (0), (int16_t) (0), (int16_t) (0), (int16_t) (0)); // 1700 } TMR2_COUNT_CAN_TX = 0; } TMR2_COUNT_CAN_TX++; } TIM3->SR = 0x0; // reset the status register }