File content as of revision 30:15743b79c6cb:

// ----------------------------------------------------------------------------
// Copyright 2016-2018 ARM Ltd.
//
// SPDX-License-Identifier: Apache-2.0
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// ----------------------------------------------------------------------------

#ifndef MBED_TEST_MODE

#include "mbed.h"
#include "simple-mbed-cloud-client.h"
#include "LittleFileSystem.h"
#include "HTS221Sensor.h"
#include "LPS22HBSensor.h"
#include "LSM6DSLSensor.h"
#include "lis3mdl_class.h"
#include "VL53L0X.h"

static DevI2C devI2c(PB_11,PB_10);
static HTS221Sensor sen_hum_temp(&devI2c);
static LPS22HBSensor sen_press_temp(&devI2c);
static LSM6DSLSensor sen_acc_gyro(&devI2c,LSM6DSL_ACC_GYRO_I2C_ADDRESS_LOW,PD_11); // low address
static LIS3MDL sen_mag(&devI2c);
static DigitalOut shutdown_pin(PC_6);
static VL53L0X sen_distance(&devI2c, &shutdown_pin, PC_7);

#define SENSORS_POLL_INTERVAL 1.0
#define SEND_ALL_SENSORS

// An event queue is a very useful structure to debounce information between contexts (e.g. ISR and normal threads)
// This is great because things such as network operations are illegal in ISR, so updating a resource in a button's fall() function is not allowed
EventQueue eventQueue;

// Default network interface object. Don't forget to change the WiFi SSID/password in mbed_app.json if you're using WiFi.
NetworkInterface *net;

// Default block device
BlockDevice* bd = BlockDevice::get_default_instance();
SlicingBlockDevice sd(bd, 0, 2*1024*1024);
LittleFileSystem fs("fs");

// Default User button for GET example
InterruptIn button(BUTTON1);
// Default LED to use for PUT/POST example
DigitalOut led(LED1);

// Declaring pointers for access to Pelion Client resources outside of main()
MbedCloudClientResource *res_button;
MbedCloudClientResource *res_led;

#ifdef SEND_ALL_SENSORS
// Temperature reading from microcontroller
AnalogIn adc_temp(ADC_TEMP);
// Voltage reference reading from microcontroller
AnalogIn adc_vref(ADC_VREF);
#endif

// Additional resources for sensor readings
MbedCloudClientResource *res_humidity;
MbedCloudClientResource *res_temperature;
#ifdef SEND_ALL_SENSORS
MbedCloudClientResource *res_pressure;
MbedCloudClientResource *res_temperature2;
MbedCloudClientResource *res_magnometer_x;
MbedCloudClientResource *res_magnometer_y;
MbedCloudClientResource *res_magnometer_z;
MbedCloudClientResource *res_accelerometer_x;
MbedCloudClientResource *res_accelerometer_y;
MbedCloudClientResource *res_accelerometer_z;
MbedCloudClientResource *res_gyroscope_x;
MbedCloudClientResource *res_gyroscope_y;
MbedCloudClientResource *res_gyroscope_z;
MbedCloudClientResource *res_distance;
MbedCloudClientResource *res_adc_temp;
MbedCloudClientResource *res_adc_voltage;
#endif /* SEND_ALL_SENSORS */

// When the device is registered, this variable will be used to access various useful information, like device ID etc.
static const ConnectorClientEndpointInfo* endpointInfo;

/**
 * PUT handler
 * @param resource The resource that triggered the callback
 * @param newValue Updated value for the resource
 */
void led_put_callback(MbedCloudClientResource *resource, m2m::String newValue) {
    printf("*** PUT received, new value: %s                             \n", newValue.c_str());
    led = atoi(newValue.c_str());
}

/**
 * POST handler
 * @param resource The resource that triggered the callback
 * @param buffer If a body was passed to the POST function, this contains the data.
 *               Note that the buffer is deallocated after leaving this function, so copy it if you need it longer.
 * @param size Size of the body
 */
void led_post_callback(MbedCloudClientResource *resource, const uint8_t *buffer, uint16_t size) {
    printf("*** POST received. Payload: %s                              \n", res_led->get_value().c_str());
    led = atoi(res_led->get_value().c_str());
}

/**
 * Button function triggered by the physical button press.
 */
void button_press() {
    int v = res_button->get_value_int() + 1;
    res_button->set_value(v);
    printf("*** Button clicked %d times                                 \n", v);
}

/**
 * Notification callback handler
 * @param resource The resource that triggered the callback
 * @param status The delivery status of the notification
 */
void button_callback(MbedCloudClientResource *resource, const NoticationDeliveryStatus status) {
    printf("*** Button notification, status %s (%d)                     \n", MbedCloudClientResource::delivery_status_to_string(status), status);
}

/**
 * Registration callback handler
 * @param endpoint Information about the registered endpoint such as the name (so you can find it back in portal)
 */
void registered(const ConnectorClientEndpointInfo *endpoint) {
    printf("Registered to Pelion Device Management. Endpoint Name: %s\n", endpoint->internal_endpoint_name.c_str());
    endpointInfo = endpoint;
}

/**
 * Initialize sensors
 */
void sensors_init() {
    uint8_t id1, id2, id3, id4;

    printf ("\nSensors configuration:\n");
    // Initialize sensors
    sen_hum_temp.init(NULL);
    sen_press_temp.init(NULL);
    sen_acc_gyro.init(NULL);
    sen_mag.init(NULL);
    sen_distance.init_sensor(VL53L0X_DEFAULT_ADDRESS);

    /// Call sensors enable routines
    sen_hum_temp.enable();
    sen_press_temp.enable();
    sen_acc_gyro.enable_x();
    sen_acc_gyro.enable_g();

    sen_hum_temp.read_id(&id1);
    sen_press_temp.read_id(&id2);
    sen_mag.read_id(&id3);
    sen_acc_gyro.read_id(&id4);

    printf("HTS221  humidity & temperature    = 0x%X\n", id1);
    printf("LPS22HB pressure & temperature    = 0x%X\n", id2);
    printf("LIS3MDL magnetometer              = 0x%X\n", id3);
    printf("LSM6DSL accelerometer & gyroscope = 0x%X\n", id4);

    printf("\n"); ;
}

/**
 * Update sensors and report their values.
 * This function is called periodically.
 */
void sensors_update() {
    float t1_val, t2_val, t3_val, h_val, p_val, v_val = 0.0;
    int32_t m_axes[3], a_axes[3], g_axes[3];
    uint32_t d_val, vl_res;

    printf("                                                             \n");

    sen_hum_temp.get_humidity(&h_val);
    sen_hum_temp.get_temperature(&t1_val);
    sen_press_temp.get_pressure(&p_val);
    sen_press_temp.get_temperature(&t2_val);
    sen_mag.get_m_axes(m_axes);
    sen_acc_gyro.get_x_axes(a_axes);
    sen_acc_gyro.get_g_axes(g_axes);
    vl_res = sen_distance.get_distance(&d_val);
    t3_val = adc_temp.read()*100;
    v_val = adc_vref.read();

    printf("ADC temp:     %5.4f C,  vref:      %5.4f V         \n", t3_val, v_val);
    printf("HTS221 temp:  %7.2f C,  humidity: %7.2f %%         \n", t1_val, h_val);
    printf("LPS22HB temp: %7.2f C,  pressure: %7.2f mbar       \n", t2_val, p_val);
    printf("LIS3MDL mag:  %7ld x, %7ld y, %7ld z [mgauss]      \n", m_axes[0], m_axes[1], m_axes[2]);
    printf("LSM6DSL acc:  %7ld x, %7ld y, %7ld z [mg]          \n", a_axes[0], a_axes[1], a_axes[2]);
    printf("LSM6DSL gyro: %7ld x, %7ld y, %7ld z [mdps]        \n", g_axes[0], g_axes[1], g_axes[2]);
    if (vl_res == VL53L0X_ERROR_NONE) {
        printf("VL53L0X dist: %7ld [mm]\n", d_val);
    } else {
        printf("VL53L0X dist:        --       \n");
    }

    printf("\r\033[8A");

    if (endpointInfo) {
        res_humidity->set_value(h_val);
        res_temperature->set_value(t1_val);
#ifdef SEND_ALL_SENSORS
        res_pressure->set_value(p_val);
        res_temperature2->set_value(t2_val);
        res_magnometer_x->set_value((float)m_axes[0]);
        res_magnometer_y->set_value((float)m_axes[1]);
        res_magnometer_z->set_value((float)m_axes[2]);
        res_accelerometer_x->set_value((float)a_axes[0]);
        res_accelerometer_y->set_value((float)a_axes[1]);
        res_accelerometer_z->set_value((float)a_axes[2]);
        res_gyroscope_x->set_value((float)g_axes[0]);
        res_gyroscope_y->set_value((float)g_axes[1]);
        res_gyroscope_z->set_value((float)g_axes[2]);
        res_distance->set_value((float)d_val);
        res_adc_temp->set_value(t3_val);
        res_adc_voltage->set_value(v_val);
#endif /* SEND_ALL_SENSORS */
    }
}

int main(void) {
    printf("\nStarting Simple Pelion Device Management Client example\n");

    int storage_status = fs.mount(&sd);
    if (storage_status != 0) {
        printf("Storage mounting failed.\n");
    }
#if USE_BUTTON == 1
    // If the User button is pressed ons start, then format storage.
    bool btn_pressed = (button.read() == MBED_CONF_APP_BUTTON_PRESSED_STATE);
    if (btn_pressed) {
        printf("User button is pushed on start...\n");
    }
#else
    bool btn_pressed = FALSE;
#endif /* USE_BUTTON */

    if (storage_status || btn_pressed) {
        printf("Formatting the storage...\n");
        int storage_status = StorageHelper::format(&fs, &sd);
        if (storage_status != 0) {
            printf("ERROR: Failed to reformat the storage (%d).\n", storage_status);
        }
    } else {
        printf("You can hold the user button during boot to format the storage and change the device identity.\n");
    }

    sensors_init();

    // Connect to the internet (DHCP is expected to be on)
    printf("Connecting to the network using Wifi...\n");
    net = NetworkInterface::get_default_instance();

    nsapi_error_t net_status = -1;
    for (int tries = 0; tries < 3; tries++) {
        net_status = net->connect();
        if (net_status == NSAPI_ERROR_OK) {
            break;
        } else {
            printf("Unable to connect to network. Retrying...\n");
        }
    }

    if (net_status != NSAPI_ERROR_OK) {
        printf("ERROR: Connecting to the network failed (%d)!\n", net_status);
        return -1;
    }

    printf("Connected to the network successfully. IP address: %s\n", net->get_ip_address());

    printf("Initializing Pelion Device Management Client...\n");

    // SimpleMbedCloudClient handles registering over LwM2M to Pelion DM
    SimpleMbedCloudClient client(net, bd, &fs);
    int client_status = client.init();
    if (client_status != 0) {
        printf("ERROR: Pelion Client initialization failed (%d)\n", client_status);
        return -1;
    }

    // Creating resources, which can be written or read from the cloud
    res_button = client.create_resource("3200/0/5501", "button_count");
    res_button->set_value(0);
    res_button->methods(M2MMethod::GET);
    res_button->observable(true);
    res_button->attach_notification_callback(button_callback);

    // Sensor resources
    res_temperature = client.create_resource("3303/0/5700", "temperature");
    res_temperature->set_value(0);
    res_temperature->methods(M2MMethod::GET);
    res_temperature->observable(true);

    res_humidity = client.create_resource("3304/0/5700", "humidity");
    res_humidity->set_value(0);
    res_humidity->methods(M2MMethod::GET);
    res_humidity->observable(true);

#ifdef SEND_ALL_SENSORS
    res_temperature2 = client.create_resource("3303/1/5700", "temperature");
    res_temperature2->set_value(0);
    res_temperature2->methods(M2MMethod::GET);
    res_temperature2->observable(true);

    res_adc_temp = client.create_resource("3303/2/5700", "temperature");
    res_adc_temp->set_value(0);
    res_adc_temp->methods(M2MMethod::GET);
    res_adc_temp->observable(true);

    res_accelerometer_x = client.create_resource("3313/0/5702", "accelerometer_x");
    res_accelerometer_x->set_value(0);
    res_accelerometer_x->methods(M2MMethod::GET);
    res_accelerometer_x->observable(true);

    res_accelerometer_y = client.create_resource("3313/0/5703", "accelerometer_y");
    res_accelerometer_y->set_value(0);
    res_accelerometer_y->methods(M2MMethod::GET);
    res_accelerometer_y->observable(true);

    res_accelerometer_z = client.create_resource("3313/0/5704", "accelerometer_z");
    res_accelerometer_z->set_value(0);
    res_accelerometer_z->methods(M2MMethod::GET);
    res_accelerometer_z->observable(true);

    res_magnometer_x = client.create_resource("3314/0/5702", "magnometer_x");
    res_magnometer_x->set_value(0);
    res_magnometer_x->methods(M2MMethod::GET);
    res_magnometer_x->observable(true);

    res_magnometer_y = client.create_resource("3314/0/5703", "magnometer_y");
    res_magnometer_y->set_value(0);
    res_magnometer_y->methods(M2MMethod::GET);
    res_magnometer_y->observable(true);

    res_magnometer_z = client.create_resource("3314/0/5704", "magnometer_z");
    res_magnometer_z->set_value(0);
    res_magnometer_z->methods(M2MMethod::GET);
    res_magnometer_z->observable(true);

    res_gyroscope_x = client.create_resource("3334/0/5702", "gyroscope_x");
    res_gyroscope_x->set_value(0);
    res_gyroscope_x->methods(M2MMethod::GET);
    res_gyroscope_x->observable(true);

    res_gyroscope_y = client.create_resource("3334/0/5703", "gyroscope_y");
    res_gyroscope_y->set_value(0);
    res_gyroscope_y->methods(M2MMethod::GET);
    res_gyroscope_y->observable(true);

    res_gyroscope_z = client.create_resource("3334/0/5704", "gyroscope_z");
    res_gyroscope_z->set_value(0);
    res_gyroscope_z->methods(M2MMethod::GET);
    res_gyroscope_z->observable(true);

    res_adc_voltage = client.create_resource("3316/0/5700", "voltage");
    res_adc_voltage->set_value(0);
    res_adc_voltage->methods(M2MMethod::GET);
    res_adc_voltage->observable(true);

    res_pressure = client.create_resource("3323/0/5700", "pressure");
    res_pressure->set_value(0);
    res_pressure->methods(M2MMethod::GET);
    res_pressure->observable(true);

    res_distance = client.create_resource("3330/0/5700", "distance");
    res_distance->set_value((float)999.9);
    res_distance->methods(M2MMethod::GET);
    res_distance->observable(true);

    res_led = client.create_resource("3201/0/5853", "led_state");
    res_led->set_value(1);
    res_led->methods(M2MMethod::GET | M2MMethod::PUT);
    res_led->attach_put_callback(led_put_callback);
#endif /* SEND_ALL_SENSORS */

    printf("Initialized Pelion Client. Registering...\n");

    // Callback that fires when registering is complete
    client.on_registered(&registered);

    // Register with Pelion DM
    client.register_and_connect();

    int i = 600; // wait up 60 seconds before attaching sensors and button events
    while (i-- > 0 && !client.is_client_registered()) {
        wait_ms(100);
    }

    button.fall(eventQueue.event(&button_press));

    // The timer fires on an interrupt context, but debounces it to the eventqueue, so it's safe to do network operations
    Ticker timer;
    timer.attach(eventQueue.event(&sensors_update), SENSORS_POLL_INTERVAL);

    // You can easily run the eventQueue in a separate thread if required
    eventQueue.dispatch_forever();
}

#endif