Gurvan PRIEM
An incomplete quadcopter control programme.
Revision 0:9cb9445a11f0, committed 2013-07-17
- Comitter:
- Gurvan
- Date:
- Wed Jul 17 15:58:25 2013 +0000
- Commit message:
- Pour Zobson, fi(r)st commit.
Changed in this revision
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/DaclePID/DaclePID.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,56 @@
+#include "DaclePID.h"
+
+
+DaclePID::DaclePID(float Kc, float Ti, float Td, float interval) {
+
+ setCoeff(Kc, Ti, Td);
+ dT_ = interval;
+
+ accError_ = 0.0;
+ pidSortie_ = 0.0;
+ erreurPres_ = 0.0;
+ minInput_=0; maxInput_=3.3;
+ minOutput_=0; maxOutput_=3.3;
+ consigne_=0;
+ biais_=0;
+
+}
+
+void DaclePID::setCoeff(float Kc, float Ti, float Td){
+
+ Kc_ = Kc;
+ Ti_ = Ti;
+ Td_= Td;
+
+}
+
+void DaclePID::setInputLimits(float minInput, float maxInput){
+ minInput_=minInput; maxInput_=maxInput;
+}
+
+void DaclePID::setOutputLimits(float minOutput, float maxOutput){
+ minOutput_=minOutput; maxOutput_=maxOutput;
+}
+
+float DaclePID::dacalcul(float erreur){
+
+ float _erreur = to01(erreur)-to01(consigne_);
+
+ accError_ += _erreur;
+ float dErreur = (_erreur - erreurPres_) /dT_;
+
+ pidSortie_ = Kc_ * (_erreur + (Ti_ * accError_ * dT_) + (Td_ * dErreur));
+
+ erreurPres_ = _erreur;
+
+ return from01(pidSortie_) - from01(biais_);
+
+}
+
+float DaclePID::to01(float x){
+ return (x-minInput_)/(maxInput_-minInput_);
+}
+
+float DaclePID::from01(float x){
+ return (maxOutput_-minOutput_)*x + minOutput_;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/DaclePID/DaclePID.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,48 @@
+#ifndef PID_H
+#define PID_H
+
+
+#include "mbed.h"
+
+class DaclePID{
+
+public:
+
+ /* Constructeur du DaclePID
+ Kc: Coeff Kc
+ Ti: Coeff Ti
+ Td: Coeff Td
+ Interval: Intervalle de temps */
+ DaclePID(float Kc, float Ti, float Td, float interval);
+
+ /* Fonction qui permet de regler les coeff du PID */
+ void setCoeff(float Kc, float Ti, float Td);
+
+ /* Fonction qui permet au DaclePID de calculer la commande
+ en entrée: Erreur */
+ void setInputLimits(float minInput, float maxInput);
+ void setOutputLimits(float minOutput, float maxOutput);
+ void setConsigne(float consigne);
+ void setBiais(float biais);
+ float dacalcul(float erreur);
+
+private:
+
+ float Kc_;
+ float Ti_;
+ float Td_;
+
+ float dT_;
+ float accError_; //Erreur accumulée (Pour l'intégrale de l'erreur)
+ float pidSortie_; //Commande
+ float erreurPres_; //Erreur au temps d'avant (pour la dérivée)
+
+ float minInput_, maxInput_, minOutput_, maxOutput_;
+ float consigne_, biais_;
+
+ float to01(float x);
+ float from01(float x);
+
+};
+
+#endif
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/GurvIMU.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,187 @@
+#include "GurvIMU.h"
+#include "MPU6050.h"
+#include "mbed.h"
+
+#define M_PI 3.1415926535897932384626433832795
+
+#define twoKpDef (2.0f * 1.0f) // 2 * proportional gain
+#define twoKiDef (2.0f * 0.0f) // 2 * integral gain
+
+
+GurvIMU::GurvIMU()
+{
+ //MPU
+ mpu = MPU6050(0x69); //0x69 = MPU6050 I2C ADDRESS
+
+ // Variable definitions
+ q0 = 1.0f, q1 = 0.0f, q2 = 0.0f, q3 = 0.0f; // quaternion of sensor frame relative to auxiliary frame
+ twoKp = twoKpDef; // 2 * proportional gain (Kp)
+ twoKi = twoKiDef; // 2 * integral gain (Ki)
+ integralFBx = 0.0f, integralFBy = 0.0f, integralFBz = 0.0f; // integral error terms scaled by Ki
+ cycle_nb = 0;
+ timer_us.start();
+}
+
+//Function definitions
+
+void GurvIMU::getValues(float * values)
+{
+ int16_t accgyroval[6];
+ mpu.getMotion6(&accgyroval[0], &accgyroval[1], &accgyroval[2], &accgyroval[3], &accgyroval[4], &accgyroval[5]);
+ for(int i = 0; i<3; i++) values[i] = (float) accgyroval[i];
+ for(int i = 3; i<6; i++) values[i] = (accgyroval[i]-offset[i]) * (M_PI / 180) / 16.4f;
+}
+
+void GurvIMU::getVerticalAcceleration(float av)
+{
+ float values[6];
+ float q[4]; // quaternion
+ float g_x, g_y, g_z; // estimated gravity direction
+ getQ(q);
+
+ g_x = 2 * (q[1]*q[3] - q[0]*q[2]);
+ g_y = 2 * (q[0]*q[1] + q[2]*q[3]);
+ g_z = q[0]*q[0] - q[1]*q[1] - q[2]*q[2] + q[3]*q[3];
+
+ getValues(values);
+ av = g_x*values[0]+g_y*values[1]+g_z*values[2]-offset[2];
+}
+
+
+void GurvIMU::getOffset(void)
+{
+ int sample_nb = 50;
+ float values[6];
+ for(int i=0; i<6 ; i++) offset[i] = 0;
+ for(int i=0; i<sample_nb; i++) {
+ getValues(values);
+ for(int j=0; j<6; j++) offset[j]+=values[j];
+ }
+ for(int j=0; j<6; j++) offset[j]/=sample_nb;
+}
+
+
+void GurvIMU::AHRS_update(float gx, float gy, float gz, float ax, float ay, float az)
+{
+ float recipNorm;
+ float halfvx, halfvy, halfvz;
+ float halfex, halfey, halfez;
+ float qa, qb, qc;
+
+ dt_us=timer_us.read_us();
+ sample_freq = 1.0 / ((dt_us) / 1000000.0);
+ timer_us.reset();
+
+ // Compute feedback only if accelerometer measurement valid (avoids NaN in accelerometer normalisation)
+ if(!((ax == 0.0f) && (ay == 0.0f) && (az == 0.0f))) {
+
+ // Normalise accelerometer measurement
+ recipNorm = invSqrt(ax * ax + ay * ay + az * az);
+ ax *= recipNorm;
+ ay *= recipNorm;
+ az *= recipNorm;
+
+ // Estimated direction of gravity
+ halfvx = q1 * q3 - q0 * q2;
+ halfvy = q0 * q1 + q2 * q3;
+ halfvz = q0 * q0 - 0.5f + q3 * q3;
+
+ // Error is sum of cross product between estimated and measured direction of gravity
+ halfex = (ay * halfvz - az * halfvy);
+ halfey = (az * halfvx - ax * halfvz);
+ halfez = (ax * halfvy - ay * halfvx);
+
+ // Compute and apply integral feedback if enabled
+ if(twoKi > 0.0f) {
+ integralFBx += twoKi * halfex * (1.0f / sample_freq); // integral error scaled by Ki
+ integralFBy += twoKi * halfey * (1.0f / sample_freq);
+ integralFBz += twoKi * halfez * (1.0f / sample_freq);
+ gx += integralFBx; // apply integral feedback
+ gy += integralFBy;
+ gz += integralFBz;
+ }
+ else {
+ integralFBx = 0.0f; // prevent integral windup
+ integralFBy = 0.0f;
+ integralFBz = 0.0f;
+ }
+
+ // Apply proportional feedback
+ gx += twoKp * halfex;
+ gy += twoKp * halfey;
+ gz += twoKp * halfez;
+ }
+
+ // Integrate rate of change of quaternion
+ gx *= (0.5f * (1.0f / sample_freq)); // pre-multiply common factors
+ gy *= (0.5f * (1.0f / sample_freq));
+ gz *= (0.5f * (1.0f / sample_freq));
+ qa = q0;
+ qb = q1;
+ qc = q2;
+ q0 += (-qb * gx - qc * gy - q3 * gz);
+ q1 += (qa * gx + qc * gz - q3 * gy);
+ q2 += (qa * gy - qb * gz + q3 * gx);
+ q3 += (qa * gz + qb * gy - qc * gx);
+
+ // Normalise quaternion
+ recipNorm = invSqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3);
+ q0 *= recipNorm;
+ q1 *= recipNorm;
+ q2 *= recipNorm;
+ q3 *= recipNorm;
+}
+
+void GurvIMU::getQ(float * q) {
+ float val[6];
+ getValues(val);
+ //while(cycle_nb < 1000){
+ AHRS_update(val[3], val[4], val[5], val[0], val[1], val[2]);
+ //cycle_nb++;}
+
+ q[0] = q0;
+ q[1] = q1;
+ q[2] = q2;
+ q[3] = q3;
+
+}
+
+void GurvIMU::getYawPitchRollRad(float * ypr) {
+ float q[4]; // quaternion
+ float g_x, g_y, g_z; // estimated gravity direction
+ getQ(q);
+
+ g_x = 2 * (q[1]*q[3] - q[0]*q[2]);
+ g_y = 2 * (q[0]*q[1] + q[2]*q[3]);
+ g_z = q[0]*q[0] - q[1]*q[1] - q[2]*q[2] + q[3]*q[3];
+
+ ypr[0] = atan2(2 * q[1] * q[2] - 2 * q[0] * q[3], 2 * q[0]*q[0] + 2 * q[1] * q[1] - 1);
+ ypr[1] = atan(g_x * invSqrt(g_y*g_y + g_z*g_z));
+ ypr[2] = atan(g_y * invSqrt(g_x*g_x + g_z*g_z));
+}
+
+void GurvIMU::init()
+{
+ mpu.initialize();
+ mpu.setI2CMasterModeEnabled(0);
+ mpu.setI2CBypassEnabled(0);
+ mpu.setFullScaleGyroRange(MPU6050_GYRO_FS_2000);
+ getOffset();
+ wait(0.005);
+}
+
+
+float invSqrt(float number)
+{
+ volatile long i;
+ volatile float x, y;
+ volatile const float f = 1.5F;
+
+ x = number * 0.5F;
+ y = number;
+ i = * ( long * ) &y;
+ i = 0x5f375a86 - ( i >> 1 );
+ y = * ( float * ) &i;
+ y = y * ( f - ( x * y * y ) );
+ return y;
+}
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/GurvIMU.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,41 @@
+#ifndef _GURVIMU_H_
+#define _GURVIMU_H_
+
+#include "mbed.h"
+#include "MPU6050.h"
+
+class GurvIMU {
+ private:
+ //Variables
+ MPU6050 mpu;
+ float twoKp; // 2 * proportional gain (Kp)
+ float twoKi; // 2 * integral gain (Ki)
+ float integralFBx, integralFBy, integralFBz; // integral error terms scaled by Ki
+ float q0, q1, q2, q3; // quaternion of sensor frame relative to auxiliary frame
+ float ax, ay, az, gx, gy, gz;
+ float sample_freq;
+ float offset[6];
+ Timer timer_us;
+ float dt_us;
+ float cycle_nb;
+
+
+ //Functions
+ void getOffset();
+
+ void AHRS_update(float gx, float gy, float gz, float ax, float ay, float az);
+ void getQ(float * q);
+
+ public:
+ GurvIMU();
+ void init();
+ void getValues(float * values);
+ void getYawPitchRollRad(float * ypr);
+ void getVerticalAcceleration(float av);
+
+};
+
+//Fast Inverse Square Root
+float invSqrt(float number);
+
+#endif /* _GURVIMU_H_ */
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/I2Cdev.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,275 @@
+// ported from arduino library: https://github.com/jrowberg/i2cdevlib
+// written by szymon gaertig (email: szymon@gaertig.com.pl, website: szymongaertig.pl)
+// Changelog:
+// 2013-01-08 - first release
+
+#include "I2Cdev.h"
+
+#define useDebugSerial
+
+I2Cdev::I2Cdev(): debugSerial(USBTX, USBRX), i2c(I2C_SDA,I2C_SCL)
+{
+
+}
+
+I2Cdev::I2Cdev(PinName i2cSda, PinName i2cScl): debugSerial(USBTX, USBRX), i2c(i2cSda,i2cScl)
+{
+
+}
+
+/** Read a single bit from an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param bitNum Bit position to read (0-7)
+ * @param data Container for single bit value
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (true = success)
+ */
+int8_t I2Cdev::readBit(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint8_t *data, uint16_t timeout) {
+ uint8_t b;
+ uint8_t count = readByte(devAddr, regAddr, &b, timeout);
+ *data = b & (1 << bitNum);
+ return count;
+}
+
+/** Read a single bit from a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param bitNum Bit position to read (0-15)
+ * @param data Container for single bit value
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (true = success)
+ */
+int8_t I2Cdev::readBitW(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint16_t *data, uint16_t timeout) {
+ uint16_t b;
+ uint8_t count = readWord(devAddr, regAddr, &b, timeout);
+ *data = b & (1 << bitNum);
+ return count;
+}
+
+/** Read multiple bits from an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param bitStart First bit position to read (0-7)
+ * @param length Number of bits to read (not more than 8)
+ * @param data Container for right-aligned value (i.e. '101' read from any bitStart position will equal 0x05)
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (true = success)
+ */
+int8_t I2Cdev::readBits(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint8_t *data, uint16_t timeout) {
+ // 01101001 read byte
+ // 76543210 bit numbers
+ // xxx args: bitStart=4, length=3
+ // 010 masked
+ // -> 010 shifted
+ uint8_t count, b;
+ if ((count = readByte(devAddr, regAddr, &b, timeout)) != 0) {
+ uint8_t mask = ((1 << length) - 1) << (bitStart - length + 1);
+ b &= mask;
+ b >>= (bitStart - length + 1);
+ *data = b;
+ }
+ return count;
+}
+
+/** Read multiple bits from a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param bitStart First bit position to read (0-15)
+ * @param length Number of bits to read (not more than 16)
+ * @param data Container for right-aligned value (i.e. '101' read from any bitStart position will equal 0x05)
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (1 = success, 0 = failure, -1 = timeout)
+ */
+int8_t I2Cdev::readBitsW(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint16_t *data, uint16_t timeout) {
+ // 1101011001101001 read byte
+ // fedcba9876543210 bit numbers
+ // xxx args: bitStart=12, length=3
+ // 010 masked
+ // -> 010 shifted
+ uint8_t count;
+ uint16_t w;
+ if ((count = readWord(devAddr, regAddr, &w, timeout)) != 0) {
+ uint16_t mask = ((1 << length) - 1) << (bitStart - length + 1);
+ w &= mask;
+ w >>= (bitStart - length + 1);
+ *data = w;
+ }
+ return count;
+}
+/** Read single byte from an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param data Container for byte value read from device
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (true = success)
+ */
+int8_t I2Cdev::readByte(uint8_t devAddr, uint8_t regAddr, uint8_t *data, uint16_t timeout) {
+ return readBytes(devAddr, regAddr, 1, data, timeout);
+}
+
+/** Read single word from a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to read from
+ * @param data Container for word value read from device
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Status of read operation (true = success)
+ */
+int8_t I2Cdev::readWord(uint8_t devAddr, uint8_t regAddr, uint16_t *data, uint16_t timeout) {
+ return readWords(devAddr, regAddr, 1, data, timeout);
+}
+
+/** Read multiple bytes from an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr First register regAddr to read from
+ * @param length Number of bytes to read
+ * @param data Buffer to store read data in
+ * @param timeout Optional read timeout in milliseconds (0 to disable, leave off to use default class value in I2Cdev::readTimeout)
+ * @return Number of bytes read (-1 indicates failure)
+ */
+int8_t I2Cdev::readBytes(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint8_t *data, uint16_t timeout)
+{
+ char command[1];
+ command[0] = regAddr;
+ char *redData = (char*)malloc(length);
+ i2c.write(devAddr<<1, command, 1, true);
+ i2c.read(devAddr<<1, redData, length);
+ for(int i =0; i < length; i++) {
+ data[i] = redData[i];
+ }
+ free(redData);
+ return length;
+}
+
+int8_t I2Cdev::readWords(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint16_t *data, uint16_t timeout)
+{
+ return 0;
+}
+
+/** write a single bit in an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to write to
+ * @param bitNum Bit position to write (0-7)
+ * @param value New bit value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeBit(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint8_t data) {
+ uint8_t b;
+ readByte(devAddr, regAddr, &b);
+ b = (data != 0) ? (b | (1 << bitNum)) : (b & ~(1 << bitNum));
+ return writeByte(devAddr, regAddr, b);
+}
+
+/** write a single bit in a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to write to
+ * @param bitNum Bit position to write (0-15)
+ * @param value New bit value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeBitW(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint16_t data) {
+ uint16_t w;
+ readWord(devAddr, regAddr, &w);
+ w = (data != 0) ? (w | (1 << bitNum)) : (w & ~(1 << bitNum));
+ return writeWord(devAddr, regAddr, w);
+}
+
+/** Write multiple bits in an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to write to
+ * @param bitStart First bit position to write (0-7)
+ * @param length Number of bits to write (not more than 8)
+ * @param data Right-aligned value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeBits(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint8_t data) {
+ // 010 value to write
+ // 76543210 bit numbers
+ // xxx args: bitStart=4, length=3
+ // 00011100 mask byte
+ // 10101111 original value (sample)
+ // 10100011 original & ~mask
+ // 10101011 masked | value
+ uint8_t b;
+ if (readByte(devAddr, regAddr, &b) != 0) {
+ uint8_t mask = ((1 << length) - 1) << (bitStart - length + 1);
+ data <<= (bitStart - length + 1); // shift data into correct position
+ data &= mask; // zero all non-important bits in data
+ b &= ~(mask); // zero all important bits in existing byte
+ b |= data; // combine data with existing byte
+ return writeByte(devAddr, regAddr, b);
+ } else {
+ return false;
+ }
+}
+
+/** Write multiple bits in a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register regAddr to write to
+ * @param bitStart First bit position to write (0-15)
+ * @param length Number of bits to write (not more than 16)
+ * @param data Right-aligned value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeBitsW(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint16_t data) {
+ // 010 value to write
+ // fedcba9876543210 bit numbers
+ // xxx args: bitStart=12, length=3
+ // 0001110000000000 mask byte
+ // 1010111110010110 original value (sample)
+ // 1010001110010110 original & ~mask
+ // 1010101110010110 masked | value
+ uint16_t w;
+ if (readWord(devAddr, regAddr, &w) != 0) {
+ uint8_t mask = ((1 << length) - 1) << (bitStart - length + 1);
+ data <<= (bitStart - length + 1); // shift data into correct position
+ data &= mask; // zero all non-important bits in data
+ w &= ~(mask); // zero all important bits in existing word
+ w |= data; // combine data with existing word
+ return writeWord(devAddr, regAddr, w);
+ } else {
+ return false;
+ }
+}
+
+/** Write single byte to an 8-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register address to write to
+ * @param data New byte value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeByte(uint8_t devAddr, uint8_t regAddr, uint8_t data) {
+ return writeBytes(devAddr, regAddr, 1, &data);
+}
+
+/** Write single word to a 16-bit device register.
+ * @param devAddr I2C slave device address
+ * @param regAddr Register address to write to
+ * @param data New word value to write
+ * @return Status of operation (true = success)
+ */
+bool I2Cdev::writeWord(uint8_t devAddr, uint8_t regAddr, uint16_t data) {
+ return writeWords(devAddr, regAddr, 1, &data);
+}
+
+bool I2Cdev::writeBytes(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint8_t *data)
+{
+ i2c.start();
+ i2c.write(devAddr<<1);
+ i2c.write(regAddr);
+ for(int i = 0; i < length; i++) {
+ i2c.write(data[i]);
+ }
+ i2c.stop();
+ return true;
+}
+
+bool I2Cdev::writeWords(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint16_t *data)
+{
+ return true;
+}
+
+uint16_t I2Cdev::readTimeout(void)
+{
+ return 0;
+}
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/I2Cdev.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,45 @@
+//ported from arduino library: https://github.com/jrowberg/i2cdevlib/tree/master/Arduino/MPU6050
+//written by szymon gaertig (email: szymon@gaertig.com.pl), small correction by Aloïs Wolff
+//
+//Changelog:
+//2013-01-08 - first beta release
+//2013-02-18 - fixed a malloc with no free in ::readBytes
+
+#ifndef I2Cdev_h
+#define I2Cdev_h
+
+#include "mbed.h"
+
+#define I2C_SDA PTE0
+#define I2C_SCL PTE1
+
+class I2Cdev {
+ private:
+ I2C i2c;
+ Serial debugSerial;
+ public:
+ I2Cdev();
+ I2Cdev(PinName i2cSda, PinName i2cScl);
+
+ int8_t readBit(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint8_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readBitW(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint16_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readBits(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint8_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readBitsW(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint16_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readByte(uint8_t devAddr, uint8_t regAddr, uint8_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readWord(uint8_t devAddr, uint8_t regAddr, uint16_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readBytes(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint8_t *data, uint16_t timeout=I2Cdev::readTimeout());
+ int8_t readWords(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint16_t *data, uint16_t timeout=I2Cdev::readTimeout());
+
+ bool writeBit(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint8_t data);
+ bool writeBitW(uint8_t devAddr, uint8_t regAddr, uint8_t bitNum, uint16_t data);
+ bool writeBits(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint8_t data);
+ bool writeBitsW(uint8_t devAddr, uint8_t regAddr, uint8_t bitStart, uint8_t length, uint16_t data);
+ bool writeByte(uint8_t devAddr, uint8_t regAddr, uint8_t data);
+ bool writeWord(uint8_t devAddr, uint8_t regAddr, uint16_t data);
+ bool writeBytes(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint8_t *data);
+ bool writeWords(uint8_t devAddr, uint8_t regAddr, uint8_t length, uint16_t *data);
+
+ static uint16_t readTimeout(void);
+};
+
+#endif
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/MPU6050.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,3433 @@
+//ported from arduino library: https://github.com/jrowberg/i2cdevlib/tree/master/Arduino/MPU6050
+//written by szymon gaertig (email: szymon@gaertig.com.pl)
+//
+//Changelog:
+//2013-01-08 - first beta release
+
+// I2Cdev library collection - MPU6050 I2C device class
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 8/24/2011 by Jeff Rowberg <jeff@rowberg.net>
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// ... - ongoing debug release
+
+// NOTE: THIS IS ONLY A PARIAL RELEASE. THIS DEVICE CLASS IS CURRENTLY UNDERGOING ACTIVE
+// DEVELOPMENT AND IS STILL MISSING SOME IMPORTANT FEATURES. PLEASE KEEP THIS IN MIND IF
+// YOU DECIDE TO USE THIS PARTICULAR CODE FOR ANYTHING.
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#include "MPU6050.h"
+
+//#define useDebugSerial
+
+//instead of using pgmspace.h
+typedef const unsigned char prog_uchar;
+#define pgm_read_byte_near(x) (*(prog_uchar*)x)
+#define pgm_read_byte(x) (*(prog_uchar*)x)
+
+/** Default constructor, uses default I2C address.
+ * @see MPU6050_DEFAULT_ADDRESS
+ */
+MPU6050::MPU6050() : debugSerial(USBTX, USBRX)
+{
+ devAddr = MPU6050_DEFAULT_ADDRESS;
+}
+
+/** Specific address constructor.
+ * @param address I2C address
+ * @see MPU6050_DEFAULT_ADDRESS
+ * @see MPU6050_ADDRESS_AD0_LOW
+ * @see MPU6050_ADDRESS_AD0_HIGH
+ */
+MPU6050::MPU6050(uint8_t address) : debugSerial(USBTX, USBRX)
+{
+ devAddr = address;
+}
+
+/** Power on and prepare for general usage.
+ * This will activate the device and take it out of sleep mode (which must be done
+ * after start-up). This function also sets both the accelerometer and the gyroscope
+ * to their most sensitive settings, namely +/- 2g and +/- 250 degrees/sec, and sets
+ * the clock source to use the X Gyro for reference, which is slightly better than
+ * the default internal clock source.
+ */
+void MPU6050::initialize()
+{
+
+ debugSerial.baud(921600); //uses max serial speed
+#ifdef useDebugSerial
+ debugSerial.printf("MPU6050::initialize start\n");
+#endif
+ setClockSource(MPU6050_CLOCK_PLL_XGYRO);
+ setFullScaleGyroRange(MPU6050_GYRO_FS_250);
+ setFullScaleAccelRange(MPU6050_ACCEL_FS_2);
+ setSleepEnabled(false); // thanks to Jack Elston for pointing this one out!
+
+#ifdef useDebugSerial
+ debugSerial.printf("MPU6050::initialize end\n");
+#endif
+}
+
+/** Verify the I2C connection.
+ * Make sure the device is connected and responds as expected.
+ * @return True if connection is valid, false otherwise
+ */
+bool MPU6050::testConnection()
+{
+#ifdef useDebugSerial
+ debugSerial.printf("MPU6050::testConnection start\n");
+#endif
+ uint8_t deviceId = getDeviceID();
+#ifdef useDebugSerial
+ debugSerial.printf("DeviceId = %d\n",deviceId);
+#endif
+ return deviceId == 0x34;
+}
+
+// AUX_VDDIO register (InvenSense demo code calls this RA_*G_OFFS_TC)
+
+/** Get the auxiliary I2C supply voltage level.
+ * When set to 1, the auxiliary I2C bus high logic level is VDD. When cleared to
+ * 0, the auxiliary I2C bus high logic level is VLOGIC. This does not apply to
+ * the MPU-6000, which does not have a VLOGIC pin.
+ * @return I2C supply voltage level (0=VLOGIC, 1=VDD)
+ */
+uint8_t MPU6050::getAuxVDDIOLevel()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_PWR_MODE_BIT, buffer);
+ return buffer[0];
+}
+/** Set the auxiliary I2C supply voltage level.
+ * When set to 1, the auxiliary I2C bus high logic level is VDD. When cleared to
+ * 0, the auxiliary I2C bus high logic level is VLOGIC. This does not apply to
+ * the MPU-6000, which does not have a VLOGIC pin.
+ * @param level I2C supply voltage level (0=VLOGIC, 1=VDD)
+ */
+void MPU6050::setAuxVDDIOLevel(uint8_t level)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_PWR_MODE_BIT, level);
+}
+
+// SMPLRT_DIV register
+
+/** Get gyroscope output rate divider.
+ * The sensor register output, FIFO output, DMP sampling, Motion detection, Zero
+ * Motion detection, and Free Fall detection are all based on the Sample Rate.
+ * The Sample Rate is generated by dividing the gyroscope output rate by
+ * SMPLRT_DIV:
+ *
+ * Sample Rate = Gyroscope Output Rate / (1 + SMPLRT_DIV)
+ *
+ * where Gyroscope Output Rate = 8kHz when the DLPF is disabled (DLPF_CFG = 0 or
+ * 7), and 1kHz when the DLPF is enabled (see Register 26).
+ *
+ * Note: The accelerometer output rate is 1kHz. This means that for a Sample
+ * Rate greater than 1kHz, the same accelerometer sample may be output to the
+ * FIFO, DMP, and sensor registers more than once.
+ *
+ * For a diagram of the gyroscope and accelerometer signal paths, see Section 8
+ * of the MPU-6000/MPU-6050 Product Specification document.
+ *
+ * @return Current sample rate
+ * @see MPU6050_RA_SMPLRT_DIV
+ */
+uint8_t MPU6050::getRate()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_SMPLRT_DIV, buffer);
+ return buffer[0];
+}
+/** Set gyroscope sample rate divider.
+ * @param rate New sample rate divider
+ * @see getRate()
+ * @see MPU6050_RA_SMPLRT_DIV
+ */
+void MPU6050::setRate(uint8_t rate)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_SMPLRT_DIV, rate);
+}
+
+
+// CONFIG register
+
+/** Get external FSYNC configuration.
+ * Configures the external Frame Synchronization (FSYNC) pin sampling. An
+ * external signal connected to the FSYNC pin can be sampled by configuring
+ * EXT_SYNC_SET. Signal changes to the FSYNC pin are latched so that short
+ * strobes may be captured. The latched FSYNC signal will be sampled at the
+ * Sampling Rate, as defined in register 25. After sampling, the latch will
+ * reset to the current FSYNC signal state.
+ *
+ * The sampled value will be reported in place of the least significant bit in
+ * a sensor data register determined by the value of EXT_SYNC_SET according to
+ * the following table.
+ *
+ * <pre>
+ * EXT_SYNC_SET | FSYNC Bit Location
+ * -------------+-------------------
+ * 0 | Input disabled
+ * 1 | TEMP_OUT_L[0]
+ * 2 | GYRO_XOUT_L[0]
+ * 3 | GYRO_YOUT_L[0]
+ * 4 | GYRO_ZOUT_L[0]
+ * 5 | ACCEL_XOUT_L[0]
+ * 6 | ACCEL_YOUT_L[0]
+ * 7 | ACCEL_ZOUT_L[0]
+ * </pre>
+ *
+ * @return FSYNC configuration value
+ */
+uint8_t MPU6050::getExternalFrameSync()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_EXT_SYNC_SET_BIT, MPU6050_CFG_EXT_SYNC_SET_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set external FSYNC configuration.
+ * @see getExternalFrameSync()
+ * @see MPU6050_RA_CONFIG
+ * @param sync New FSYNC configuration value
+ */
+void MPU6050::setExternalFrameSync(uint8_t sync)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_EXT_SYNC_SET_BIT, MPU6050_CFG_EXT_SYNC_SET_LENGTH, sync);
+}
+/** Get digital low-pass filter configuration.
+ * The DLPF_CFG parameter sets the digital low pass filter configuration. It
+ * also determines the internal sampling rate used by the device as shown in
+ * the table below.
+ *
+ * Note: The accelerometer output rate is 1kHz. This means that for a Sample
+ * Rate greater than 1kHz, the same accelerometer sample may be output to the
+ * FIFO, DMP, and sensor registers more than once.
+ *
+ * <pre>
+ * | ACCELEROMETER | GYROSCOPE
+ * DLPF_CFG | Bandwidth | Delay | Bandwidth | Delay | Sample Rate
+ * ---------+-----------+--------+-----------+--------+-------------
+ * 0 | 260Hz | 0ms | 256Hz | 0.98ms | 8kHz
+ * 1 | 184Hz | 2.0ms | 188Hz | 1.9ms | 1kHz
+ * 2 | 94Hz | 3.0ms | 98Hz | 2.8ms | 1kHz
+ * 3 | 44Hz | 4.9ms | 42Hz | 4.8ms | 1kHz
+ * 4 | 21Hz | 8.5ms | 20Hz | 8.3ms | 1kHz
+ * 5 | 10Hz | 13.8ms | 10Hz | 13.4ms | 1kHz
+ * 6 | 5Hz | 19.0ms | 5Hz | 18.6ms | 1kHz
+ * 7 | -- Reserved -- | -- Reserved -- | Reserved
+ * </pre>
+ *
+ * @return DLFP configuration
+ * @see MPU6050_RA_CONFIG
+ * @see MPU6050_CFG_DLPF_CFG_BIT
+ * @see MPU6050_CFG_DLPF_CFG_LENGTH
+ */
+uint8_t MPU6050::getDLPFMode()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_DLPF_CFG_BIT, MPU6050_CFG_DLPF_CFG_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set digital low-pass filter configuration.
+ * @param mode New DLFP configuration setting
+ * @see getDLPFBandwidth()
+ * @see MPU6050_DLPF_BW_256
+ * @see MPU6050_RA_CONFIG
+ * @see MPU6050_CFG_DLPF_CFG_BIT
+ * @see MPU6050_CFG_DLPF_CFG_LENGTH
+ */
+void MPU6050::setDLPFMode(uint8_t mode)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_DLPF_CFG_BIT, MPU6050_CFG_DLPF_CFG_LENGTH, mode);
+}
+
+// GYRO_CONFIG register
+
+/** Get full-scale gyroscope range.
+ * The FS_SEL parameter allows setting the full-scale range of the gyro sensors,
+ * as described in the table below.
+ *
+ * <pre>
+ * 0 = +/- 250 degrees/sec
+ * 1 = +/- 500 degrees/sec
+ * 2 = +/- 1000 degrees/sec
+ * 3 = +/- 2000 degrees/sec
+ * </pre>
+ *
+ * @return Current full-scale gyroscope range setting
+ * @see MPU6050_GYRO_FS_250
+ * @see MPU6050_RA_GYRO_CONFIG
+ * @see MPU6050_GCONFIG_FS_SEL_BIT
+ * @see MPU6050_GCONFIG_FS_SEL_LENGTH
+ */
+uint8_t MPU6050::getFullScaleGyroRange()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_GYRO_CONFIG, MPU6050_GCONFIG_FS_SEL_BIT, MPU6050_GCONFIG_FS_SEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set full-scale gyroscope range.
+ * @param range New full-scale gyroscope range value
+ * @see getFullScaleRange()
+ * @see MPU6050_GYRO_FS_250
+ * @see MPU6050_RA_GYRO_CONFIG
+ * @see MPU6050_GCONFIG_FS_SEL_BIT
+ * @see MPU6050_GCONFIG_FS_SEL_LENGTH
+ */
+void MPU6050::setFullScaleGyroRange(uint8_t range)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_GYRO_CONFIG, MPU6050_GCONFIG_FS_SEL_BIT, MPU6050_GCONFIG_FS_SEL_LENGTH, range);
+}
+
+// ACCEL_CONFIG register
+
+/** Get self-test enabled setting for accelerometer X axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelXSelfTest()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_XA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Get self-test enabled setting for accelerometer X axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelXSelfTest(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_XA_ST_BIT, enabled);
+}
+/** Get self-test enabled value for accelerometer Y axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelYSelfTest()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_YA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Get self-test enabled value for accelerometer Y axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelYSelfTest(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_YA_ST_BIT, enabled);
+}
+/** Get self-test enabled value for accelerometer Z axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelZSelfTest()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ZA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Set self-test enabled value for accelerometer Z axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelZSelfTest(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ZA_ST_BIT, enabled);
+}
+/** Get full-scale accelerometer range.
+ * The FS_SEL parameter allows setting the full-scale range of the accelerometer
+ * sensors, as described in the table below.
+ *
+ * <pre>
+ * 0 = +/- 2g
+ * 1 = +/- 4g
+ * 2 = +/- 8g
+ * 3 = +/- 16g
+ * </pre>
+ *
+ * @return Current full-scale accelerometer range setting
+ * @see MPU6050_ACCEL_FS_2
+ * @see MPU6050_RA_ACCEL_CONFIG
+ * @see MPU6050_ACONFIG_AFS_SEL_BIT
+ * @see MPU6050_ACONFIG_AFS_SEL_LENGTH
+ */
+uint8_t MPU6050::getFullScaleAccelRange()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_AFS_SEL_BIT, MPU6050_ACONFIG_AFS_SEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set full-scale accelerometer range.
+ * @param range New full-scale accelerometer range setting
+ * @see getFullScaleAccelRange()
+ */
+void MPU6050::setFullScaleAccelRange(uint8_t range)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_AFS_SEL_BIT, MPU6050_ACONFIG_AFS_SEL_LENGTH, range);
+}
+/** Get the high-pass filter configuration.
+ * The DHPF is a filter module in the path leading to motion detectors (Free
+ * Fall, Motion threshold, and Zero Motion). The high pass filter output is not
+ * available to the data registers (see Figure in Section 8 of the MPU-6000/
+ * MPU-6050 Product Specification document).
+ *
+ * The high pass filter has three modes:
+ *
+ * <pre>
+ * Reset: The filter output settles to zero within one sample. This
+ * effectively disables the high pass filter. This mode may be toggled
+ * to quickly settle the filter.
+ *
+ * On: The high pass filter will pass signals above the cut off frequency.
+ *
+ * Hold: When triggered, the filter holds the present sample. The filter
+ * output will be the difference between the input sample and the held
+ * sample.
+ * </pre>
+ *
+ * <pre>
+ * ACCEL_HPF | Filter Mode | Cut-off Frequency
+ * ----------+-------------+------------------
+ * 0 | Reset | None
+ * 1 | On | 5Hz
+ * 2 | On | 2.5Hz
+ * 3 | On | 1.25Hz
+ * 4 | On | 0.63Hz
+ * 7 | Hold | None
+ * </pre>
+ *
+ * @return Current high-pass filter configuration
+ * @see MPU6050_DHPF_RESET
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+uint8_t MPU6050::getDHPFMode()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ACCEL_HPF_BIT, MPU6050_ACONFIG_ACCEL_HPF_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set the high-pass filter configuration.
+ * @param bandwidth New high-pass filter configuration
+ * @see setDHPFMode()
+ * @see MPU6050_DHPF_RESET
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setDHPFMode(uint8_t bandwidth)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ACCEL_HPF_BIT, MPU6050_ACONFIG_ACCEL_HPF_LENGTH, bandwidth);
+}
+
+// FF_THR register
+
+/** Get free-fall event acceleration threshold.
+ * This register configures the detection threshold for Free Fall event
+ * detection. The unit of FF_THR is 1LSB = 2mg. Free Fall is detected when the
+ * absolute value of the accelerometer measurements for the three axes are each
+ * less than the detection threshold. This condition increments the Free Fall
+ * duration counter (Register 30). The Free Fall interrupt is triggered when the
+ * Free Fall duration counter reaches the time specified in FF_DUR.
+ *
+ * For more details on the Free Fall detection interrupt, see Section 8.2 of the
+ * MPU-6000/MPU-6050 Product Specification document as well as Registers 56 and
+ * 58 of this document.
+ *
+ * @return Current free-fall acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_FF_THR
+ */
+uint8_t MPU6050::getFreefallDetectionThreshold()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_FF_THR, buffer);
+ return buffer[0];
+}
+/** Get free-fall event acceleration threshold.
+ * @param threshold New free-fall acceleration threshold value (LSB = 2mg)
+ * @see getFreefallDetectionThreshold()
+ * @see MPU6050_RA_FF_THR
+ */
+void MPU6050::setFreefallDetectionThreshold(uint8_t threshold)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_FF_THR, threshold);
+}
+
+// FF_DUR register
+
+/** Get free-fall event duration threshold.
+ * This register configures the duration counter threshold for Free Fall event
+ * detection. The duration counter ticks at 1kHz, therefore FF_DUR has a unit
+ * of 1 LSB = 1 ms.
+ *
+ * The Free Fall duration counter increments while the absolute value of the
+ * accelerometer measurements are each less than the detection threshold
+ * (Register 29). The Free Fall interrupt is triggered when the Free Fall
+ * duration counter reaches the time specified in this register.
+ *
+ * For more details on the Free Fall detection interrupt, see Section 8.2 of
+ * the MPU-6000/MPU-6050 Product Specification document as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current free-fall duration threshold value (LSB = 1ms)
+ * @see MPU6050_RA_FF_DUR
+ */
+uint8_t MPU6050::getFreefallDetectionDuration()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_FF_DUR, buffer);
+ return buffer[0];
+}
+/** Get free-fall event duration threshold.
+ * @param duration New free-fall duration threshold value (LSB = 1ms)
+ * @see getFreefallDetectionDuration()
+ * @see MPU6050_RA_FF_DUR
+ */
+void MPU6050::setFreefallDetectionDuration(uint8_t duration)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_FF_DUR, duration);
+}
+
+// MOT_THR register
+
+/** Get motion detection event acceleration threshold.
+ * This register configures the detection threshold for Motion interrupt
+ * generation. The unit of MOT_THR is 1LSB = 2mg. Motion is detected when the
+ * absolute value of any of the accelerometer measurements exceeds this Motion
+ * detection threshold. This condition increments the Motion detection duration
+ * counter (Register 32). The Motion detection interrupt is triggered when the
+ * Motion Detection counter reaches the time count specified in MOT_DUR
+ * (Register 32).
+ *
+ * The Motion interrupt will indicate the axis and polarity of detected motion
+ * in MOT_DETECT_STATUS (Register 97).
+ *
+ * For more details on the Motion detection interrupt, see Section 8.3 of the
+ * MPU-6000/MPU-6050 Product Specification document as well as Registers 56 and
+ * 58 of this document.
+ *
+ * @return Current motion detection acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_MOT_THR
+ */
+uint8_t MPU6050::getMotionDetectionThreshold()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_MOT_THR, buffer);
+ return buffer[0];
+}
+/** Set free-fall event acceleration threshold.
+ * @param threshold New motion detection acceleration threshold value (LSB = 2mg)
+ * @see getMotionDetectionThreshold()
+ * @see MPU6050_RA_MOT_THR
+ */
+void MPU6050::setMotionDetectionThreshold(uint8_t threshold)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_MOT_THR, threshold);
+}
+
+// MOT_DUR register
+
+/** Get motion detection event duration threshold.
+ * This register configures the duration counter threshold for Motion interrupt
+ * generation. The duration counter ticks at 1 kHz, therefore MOT_DUR has a unit
+ * of 1LSB = 1ms. The Motion detection duration counter increments when the
+ * absolute value of any of the accelerometer measurements exceeds the Motion
+ * detection threshold (Register 31). The Motion detection interrupt is
+ * triggered when the Motion detection counter reaches the time count specified
+ * in this register.
+ *
+ * For more details on the Motion detection interrupt, see Section 8.3 of the
+ * MPU-6000/MPU-6050 Product Specification document.
+ *
+ * @return Current motion detection duration threshold value (LSB = 1ms)
+ * @see MPU6050_RA_MOT_DUR
+ */
+uint8_t MPU6050::getMotionDetectionDuration()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_MOT_DUR, buffer);
+ return buffer[0];
+}
+/** Set motion detection event duration threshold.
+ * @param duration New motion detection duration threshold value (LSB = 1ms)
+ * @see getMotionDetectionDuration()
+ * @see MPU6050_RA_MOT_DUR
+ */
+void MPU6050::setMotionDetectionDuration(uint8_t duration)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_MOT_DUR, duration);
+}
+
+// ZRMOT_THR register
+
+/** Get zero motion detection event acceleration threshold.
+ * This register configures the detection threshold for Zero Motion interrupt
+ * generation. The unit of ZRMOT_THR is 1LSB = 2mg. Zero Motion is detected when
+ * the absolute value of the accelerometer measurements for the 3 axes are each
+ * less than the detection threshold. This condition increments the Zero Motion
+ * duration counter (Register 34). The Zero Motion interrupt is triggered when
+ * the Zero Motion duration counter reaches the time count specified in
+ * ZRMOT_DUR (Register 34).
+ *
+ * Unlike Free Fall or Motion detection, Zero Motion detection triggers an
+ * interrupt both when Zero Motion is first detected and when Zero Motion is no
+ * longer detected.
+ *
+ * When a zero motion event is detected, a Zero Motion Status will be indicated
+ * in the MOT_DETECT_STATUS register (Register 97). When a motion-to-zero-motion
+ * condition is detected, the status bit is set to 1. When a zero-motion-to-
+ * motion condition is detected, the status bit is set to 0.
+ *
+ * For more details on the Zero Motion detection interrupt, see Section 8.4 of
+ * the MPU-6000/MPU-6050 Product Specification document as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current zero motion detection acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_ZRMOT_THR
+ */
+uint8_t MPU6050::getZeroMotionDetectionThreshold()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_ZRMOT_THR, buffer);
+ return buffer[0];
+}
+/** Set zero motion detection event acceleration threshold.
+ * @param threshold New zero motion detection acceleration threshold value (LSB = 2mg)
+ * @see getZeroMotionDetectionThreshold()
+ * @see MPU6050_RA_ZRMOT_THR
+ */
+void MPU6050::setZeroMotionDetectionThreshold(uint8_t threshold)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_ZRMOT_THR, threshold);
+}
+
+// ZRMOT_DUR register
+
+/** Get zero motion detection event duration threshold.
+ * This register configures the duration counter threshold for Zero Motion
+ * interrupt generation. The duration counter ticks at 16 Hz, therefore
+ * ZRMOT_DUR has a unit of 1 LSB = 64 ms. The Zero Motion duration counter
+ * increments while the absolute value of the accelerometer measurements are
+ * each less than the detection threshold (Register 33). The Zero Motion
+ * interrupt is triggered when the Zero Motion duration counter reaches the time
+ * count specified in this register.
+ *
+ * For more details on the Zero Motion detection interrupt, see Section 8.4 of
+ * the MPU-6000/MPU-6050 Product Specification document, as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current zero motion detection duration threshold value (LSB = 64ms)
+ * @see MPU6050_RA_ZRMOT_DUR
+ */
+uint8_t MPU6050::getZeroMotionDetectionDuration()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_ZRMOT_DUR, buffer);
+ return buffer[0];
+}
+/** Set zero motion detection event duration threshold.
+ * @param duration New zero motion detection duration threshold value (LSB = 1ms)
+ * @see getZeroMotionDetectionDuration()
+ * @see MPU6050_RA_ZRMOT_DUR
+ */
+void MPU6050::setZeroMotionDetectionDuration(uint8_t duration)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_ZRMOT_DUR, duration);
+}
+
+// FIFO_EN register
+
+/** Get temperature FIFO enabled value.
+ * When set to 1, this bit enables TEMP_OUT_H and TEMP_OUT_L (Registers 65 and
+ * 66) to be written into the FIFO buffer.
+ * @return Current temperature FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getTempFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_TEMP_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set temperature FIFO enabled value.
+ * @param enabled New temperature FIFO enabled value
+ * @see getTempFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setTempFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_TEMP_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope X-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_XOUT_H and GYRO_XOUT_L (Registers 67 and
+ * 68) to be written into the FIFO buffer.
+ * @return Current gyroscope X-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getXGyroFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_XG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope X-axis FIFO enabled value.
+ * @param enabled New gyroscope X-axis FIFO enabled value
+ * @see getXGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setXGyroFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_XG_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope Y-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_YOUT_H and GYRO_YOUT_L (Registers 69 and
+ * 70) to be written into the FIFO buffer.
+ * @return Current gyroscope Y-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getYGyroFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_YG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope Y-axis FIFO enabled value.
+ * @param enabled New gyroscope Y-axis FIFO enabled value
+ * @see getYGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setYGyroFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_YG_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope Z-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_ZOUT_H and GYRO_ZOUT_L (Registers 71 and
+ * 72) to be written into the FIFO buffer.
+ * @return Current gyroscope Z-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getZGyroFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ZG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope Z-axis FIFO enabled value.
+ * @param enabled New gyroscope Z-axis FIFO enabled value
+ * @see getZGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setZGyroFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ZG_FIFO_EN_BIT, enabled);
+}
+/** Get accelerometer FIFO enabled value.
+ * When set to 1, this bit enables ACCEL_XOUT_H, ACCEL_XOUT_L, ACCEL_YOUT_H,
+ * ACCEL_YOUT_L, ACCEL_ZOUT_H, and ACCEL_ZOUT_L (Registers 59 to 64) to be
+ * written into the FIFO buffer.
+ * @return Current accelerometer FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getAccelFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ACCEL_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set accelerometer FIFO enabled value.
+ * @param enabled New accelerometer FIFO enabled value
+ * @see getAccelFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setAccelFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ACCEL_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 2 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 2 to be written into the FIFO buffer.
+ * @return Current Slave 2 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave2FIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV2_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 2 FIFO enabled value.
+ * @param enabled New Slave 2 FIFO enabled value
+ * @see getSlave2FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave2FIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV2_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 1 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 1 to be written into the FIFO buffer.
+ * @return Current Slave 1 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave1FIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV1_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 1 FIFO enabled value.
+ * @param enabled New Slave 1 FIFO enabled value
+ * @see getSlave1FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave1FIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV1_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 0 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 0 to be written into the FIFO buffer.
+ * @return Current Slave 0 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave0FIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV0_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 0 FIFO enabled value.
+ * @param enabled New Slave 0 FIFO enabled value
+ * @see getSlave0FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave0FIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV0_FIFO_EN_BIT, enabled);
+}
+
+// I2C_MST_CTRL register
+
+/** Get multi-master enabled value.
+ * Multi-master capability allows multiple I2C masters to operate on the same
+ * bus. In circuits where multi-master capability is required, set MULT_MST_EN
+ * to 1. This will increase current drawn by approximately 30uA.
+ *
+ * In circuits where multi-master capability is required, the state of the I2C
+ * bus must always be monitored by each separate I2C Master. Before an I2C
+ * Master can assume arbitration of the bus, it must first confirm that no other
+ * I2C Master has arbitration of the bus. When MULT_MST_EN is set to 1, the
+ * MPU-60X0's bus arbitration detection logic is turned on, enabling it to
+ * detect when the bus is available.
+ *
+ * @return Current multi-master enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getMultiMasterEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_MULT_MST_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set multi-master enabled value.
+ * @param enabled New multi-master enabled value
+ * @see getMultiMasterEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setMultiMasterEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_MULT_MST_EN_BIT, enabled);
+}
+/** Get wait-for-external-sensor-data enabled value.
+ * When the WAIT_FOR_ES bit is set to 1, the Data Ready interrupt will be
+ * delayed until External Sensor data from the Slave Devices are loaded into the
+ * EXT_SENS_DATA registers. This is used to ensure that both the internal sensor
+ * data (i.e. from gyro and accel) and external sensor data have been loaded to
+ * their respective data registers (i.e. the data is synced) when the Data Ready
+ * interrupt is triggered.
+ *
+ * @return Current wait-for-external-sensor-data enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getWaitForExternalSensorEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_WAIT_FOR_ES_BIT, buffer);
+ return buffer[0];
+}
+/** Set wait-for-external-sensor-data enabled value.
+ * @param enabled New wait-for-external-sensor-data enabled value
+ * @see getWaitForExternalSensorEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setWaitForExternalSensorEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_WAIT_FOR_ES_BIT, enabled);
+}
+/** Get Slave 3 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 3 to be written into the FIFO buffer.
+ * @return Current Slave 3 FIFO enabled value
+ * @see MPU6050_RA_MST_CTRL
+ */
+bool MPU6050::getSlave3FIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_SLV_3_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 3 FIFO enabled value.
+ * @param enabled New Slave 3 FIFO enabled value
+ * @see getSlave3FIFOEnabled()
+ * @see MPU6050_RA_MST_CTRL
+ */
+void MPU6050::setSlave3FIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_SLV_3_FIFO_EN_BIT, enabled);
+}
+/** Get slave read/write transition enabled value.
+ * The I2C_MST_P_NSR bit configures the I2C Master's transition from one slave
+ * read to the next slave read. If the bit equals 0, there will be a restart
+ * between reads. If the bit equals 1, there will be a stop followed by a start
+ * of the following read. When a write transaction follows a read transaction,
+ * the stop followed by a start of the successive write will be always used.
+ *
+ * @return Current slave read/write transition enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getSlaveReadWriteTransitionEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_P_NSR_BIT, buffer);
+ return buffer[0];
+}
+/** Set slave read/write transition enabled value.
+ * @param enabled New slave read/write transition enabled value
+ * @see getSlaveReadWriteTransitionEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setSlaveReadWriteTransitionEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_P_NSR_BIT, enabled);
+}
+/** Get I2C master clock speed.
+ * I2C_MST_CLK is a 4 bit unsigned value which configures a divider on the
+ * MPU-60X0 internal 8MHz clock. It sets the I2C master clock speed according to
+ * the following table:
+ *
+ * <pre>
+ * I2C_MST_CLK | I2C Master Clock Speed | 8MHz Clock Divider
+ * ------------+------------------------+-------------------
+ * 0 | 348kHz | 23
+ * 1 | 333kHz | 24
+ * 2 | 320kHz | 25
+ * 3 | 308kHz | 26
+ * 4 | 296kHz | 27
+ * 5 | 286kHz | 28
+ * 6 | 276kHz | 29
+ * 7 | 267kHz | 30
+ * 8 | 258kHz | 31
+ * 9 | 500kHz | 16
+ * 10 | 471kHz | 17
+ * 11 | 444kHz | 18
+ * 12 | 421kHz | 19
+ * 13 | 400kHz | 20
+ * 14 | 381kHz | 21
+ * 15 | 364kHz | 22
+ * </pre>
+ *
+ * @return Current I2C master clock speed
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+uint8_t MPU6050::getMasterClockSpeed()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_CLK_BIT, MPU6050_I2C_MST_CLK_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set I2C master clock speed.
+ * @reparam speed Current I2C master clock speed
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setMasterClockSpeed(uint8_t speed)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_CLK_BIT, MPU6050_I2C_MST_CLK_LENGTH, speed);
+}
+
+// I2C_SLV* registers (Slave 0-3)
+
+/** Get the I2C address of the specified slave (0-3).
+ * Note that Bit 7 (MSB) controls read/write mode. If Bit 7 is set, it's a read
+ * operation, and if it is cleared, then it's a write operation. The remaining
+ * bits (6-0) are the 7-bit device address of the slave device.
+ *
+ * In read mode, the result of the read is placed in the lowest available
+ * EXT_SENS_DATA register. For further information regarding the allocation of
+ * read results, please refer to the EXT_SENS_DATA register description
+ * (Registers 73 - 96).
+ *
+ * The MPU-6050 supports a total of five slaves, but Slave 4 has unique
+ * characteristics, and so it has its own functions (getSlave4* and setSlave4*).
+ *
+ * I2C data transactions are performed at the Sample Rate, as defined in
+ * Register 25. The user is responsible for ensuring that I2C data transactions
+ * to and from each enabled Slave can be completed within a single period of the
+ * Sample Rate.
+ *
+ * The I2C slave access rate can be reduced relative to the Sample Rate. This
+ * reduced access rate is determined by I2C_MST_DLY (Register 52). Whether a
+ * slave's access rate is reduced relative to the Sample Rate is determined by
+ * I2C_MST_DELAY_CTRL (Register 103).
+ *
+ * The processing order for the slaves is fixed. The sequence followed for
+ * processing the slaves is Slave 0, Slave 1, Slave 2, Slave 3 and Slave 4. If a
+ * particular Slave is disabled it will be skipped.
+ *
+ * Each slave can either be accessed at the sample rate or at a reduced sample
+ * rate. In a case where some slaves are accessed at the Sample Rate and some
+ * slaves are accessed at the reduced rate, the sequence of accessing the slaves
+ * (Slave 0 to Slave 4) is still followed. However, the reduced rate slaves will
+ * be skipped if their access rate dictates that they should not be accessed
+ * during that particular cycle. For further information regarding the reduced
+ * access rate, please refer to Register 52. Whether a slave is accessed at the
+ * Sample Rate or at the reduced rate is determined by the Delay Enable bits in
+ * Register 103.
+ *
+ * @param num Slave number (0-3)
+ * @return Current address for specified slave
+ * @see MPU6050_RA_I2C_SLV0_ADDR
+ */
+uint8_t MPU6050::getSlaveAddress(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readByte(devAddr, MPU6050_RA_I2C_SLV0_ADDR + num*3, buffer);
+ return buffer[0];
+}
+/** Set the I2C address of the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param address New address for specified slave
+ * @see getSlaveAddress()
+ * @see MPU6050_RA_I2C_SLV0_ADDR
+ */
+void MPU6050::setSlaveAddress(uint8_t num, uint8_t address)
+{
+ if (num > 3) return;
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV0_ADDR + num*3, address);
+}
+/** Get the active internal register for the specified slave (0-3).
+ * Read/write operations for this slave will be done to whatever internal
+ * register address is stored in this MPU register.
+ *
+ * The MPU-6050 supports a total of five slaves, but Slave 4 has unique
+ * characteristics, and so it has its own functions.
+ *
+ * @param num Slave number (0-3)
+ * @return Current active register for specified slave
+ * @see MPU6050_RA_I2C_SLV0_REG
+ */
+uint8_t MPU6050::getSlaveRegister(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readByte(devAddr, MPU6050_RA_I2C_SLV0_REG + num*3, buffer);
+ return buffer[0];
+}
+/** Set the active internal register for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param reg New active register for specified slave
+ * @see getSlaveRegister()
+ * @see MPU6050_RA_I2C_SLV0_REG
+ */
+void MPU6050::setSlaveRegister(uint8_t num, uint8_t reg)
+{
+ if (num > 3) return;
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV0_REG + num*3, reg);
+}
+/** Get the enabled value for the specified slave (0-3).
+ * When set to 1, this bit enables Slave 0 for data transfer operations. When
+ * cleared to 0, this bit disables Slave 0 from data transfer operations.
+ * @param num Slave number (0-3)
+ * @return Current enabled value for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveEnabled(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New enabled value for specified slave
+ * @see getSlaveEnabled()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveEnabled(uint8_t num, bool enabled)
+{
+ if (num > 3) return;
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_EN_BIT, enabled);
+}
+/** Get word pair byte-swapping enabled for the specified slave (0-3).
+ * When set to 1, this bit enables byte swapping. When byte swapping is enabled,
+ * the high and low bytes of a word pair are swapped. Please refer to
+ * I2C_SLV0_GRP for the pairing convention of the word pairs. When cleared to 0,
+ * bytes transferred to and from Slave 0 will be written to EXT_SENS_DATA
+ * registers in the order they were transferred.
+ *
+ * @param num Slave number (0-3)
+ * @return Current word pair byte-swapping enabled value for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWordByteSwap(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_BYTE_SW_BIT, buffer);
+ return buffer[0];
+}
+/** Set word pair byte-swapping enabled for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New word pair byte-swapping enabled value for specified slave
+ * @see getSlaveWordByteSwap()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWordByteSwap(uint8_t num, bool enabled)
+{
+ if (num > 3) return;
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_BYTE_SW_BIT, enabled);
+}
+/** Get write mode for the specified slave (0-3).
+ * When set to 1, the transaction will read or write data only. When cleared to
+ * 0, the transaction will write a register address prior to reading or writing
+ * data. This should equal 0 when specifying the register address within the
+ * Slave device to/from which the ensuing data transaction will take place.
+ *
+ * @param num Slave number (0-3)
+ * @return Current write mode for specified slave (0 = register address + data, 1 = data only)
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWriteMode(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_REG_DIS_BIT, buffer);
+ return buffer[0];
+}
+/** Set write mode for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param mode New write mode for specified slave (0 = register address + data, 1 = data only)
+ * @see getSlaveWriteMode()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWriteMode(uint8_t num, bool mode)
+{
+ if (num > 3) return;
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_REG_DIS_BIT, mode);
+}
+/** Get word pair grouping order offset for the specified slave (0-3).
+ * This sets specifies the grouping order of word pairs received from registers.
+ * When cleared to 0, bytes from register addresses 0 and 1, 2 and 3, etc (even,
+ * then odd register addresses) are paired to form a word. When set to 1, bytes
+ * from register addresses are paired 1 and 2, 3 and 4, etc. (odd, then even
+ * register addresses) are paired to form a word.
+ *
+ * @param num Slave number (0-3)
+ * @return Current word pair grouping order offset for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWordGroupOffset(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_GRP_BIT, buffer);
+ return buffer[0];
+}
+/** Set word pair grouping order offset for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New word pair grouping order offset for specified slave
+ * @see getSlaveWordGroupOffset()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWordGroupOffset(uint8_t num, bool enabled)
+{
+ if (num > 3) return;
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_GRP_BIT, enabled);
+}
+/** Get number of bytes to read for the specified slave (0-3).
+ * Specifies the number of bytes transferred to and from Slave 0. Clearing this
+ * bit to 0 is equivalent to disabling the register by writing 0 to I2C_SLV0_EN.
+ * @param num Slave number (0-3)
+ * @return Number of bytes to read for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+uint8_t MPU6050::getSlaveDataLength(uint8_t num)
+{
+ if (num > 3) return 0;
+ i2Cdev.readBits(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_LEN_BIT, MPU6050_I2C_SLV_LEN_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set number of bytes to read for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param length Number of bytes to read for specified slave
+ * @see getSlaveDataLength()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveDataLength(uint8_t num, uint8_t length)
+{
+ if (num > 3) return;
+ i2Cdev.writeBits(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_LEN_BIT, MPU6050_I2C_SLV_LEN_LENGTH, length);
+}
+
+// I2C_SLV* registers (Slave 4)
+
+/** Get the I2C address of Slave 4.
+ * Note that Bit 7 (MSB) controls read/write mode. If Bit 7 is set, it's a read
+ * operation, and if it is cleared, then it's a write operation. The remaining
+ * bits (6-0) are the 7-bit device address of the slave device.
+ *
+ * @return Current address for Slave 4
+ * @see getSlaveAddress()
+ * @see MPU6050_RA_I2C_SLV4_ADDR
+ */
+uint8_t MPU6050::getSlave4Address()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_I2C_SLV4_ADDR, buffer);
+ return buffer[0];
+}
+/** Set the I2C address of Slave 4.
+ * @param address New address for Slave 4
+ * @see getSlave4Address()
+ * @see MPU6050_RA_I2C_SLV4_ADDR
+ */
+void MPU6050::setSlave4Address(uint8_t address)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV4_ADDR, address);
+}
+/** Get the active internal register for the Slave 4.
+ * Read/write operations for this slave will be done to whatever internal
+ * register address is stored in this MPU register.
+ *
+ * @return Current active register for Slave 4
+ * @see MPU6050_RA_I2C_SLV4_REG
+ */
+uint8_t MPU6050::getSlave4Register()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_I2C_SLV4_REG, buffer);
+ return buffer[0];
+}
+/** Set the active internal register for Slave 4.
+ * @param reg New active register for Slave 4
+ * @see getSlave4Register()
+ * @see MPU6050_RA_I2C_SLV4_REG
+ */
+void MPU6050::setSlave4Register(uint8_t reg)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV4_REG, reg);
+}
+/** Set new byte to write to Slave 4.
+ * This register stores the data to be written into the Slave 4. If I2C_SLV4_RW
+ * is set 1 (set to read), this register has no effect.
+ * @param data New byte to write to Slave 4
+ * @see MPU6050_RA_I2C_SLV4_DO
+ */
+void MPU6050::setSlave4OutputByte(uint8_t data)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV4_DO, data);
+}
+/** Get the enabled value for the Slave 4.
+ * When set to 1, this bit enables Slave 4 for data transfer operations. When
+ * cleared to 0, this bit disables Slave 4 from data transfer operations.
+ * @return Current enabled value for Slave 4
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4Enabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for Slave 4.
+ * @param enabled New enabled value for Slave 4
+ * @see getSlave4Enabled()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4Enabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_EN_BIT, enabled);
+}
+/** Get the enabled value for Slave 4 transaction interrupts.
+ * When set to 1, this bit enables the generation of an interrupt signal upon
+ * completion of a Slave 4 transaction. When cleared to 0, this bit disables the
+ * generation of an interrupt signal upon completion of a Slave 4 transaction.
+ * The interrupt status can be observed in Register 54.
+ *
+ * @return Current enabled value for Slave 4 transaction interrupts.
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4InterruptEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for Slave 4 transaction interrupts.
+ * @param enabled New enabled value for Slave 4 transaction interrupts.
+ * @see getSlave4InterruptEnabled()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4InterruptEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_INT_EN_BIT, enabled);
+}
+/** Get write mode for Slave 4.
+ * When set to 1, the transaction will read or write data only. When cleared to
+ * 0, the transaction will write a register address prior to reading or writing
+ * data. This should equal 0 when specifying the register address within the
+ * Slave device to/from which the ensuing data transaction will take place.
+ *
+ * @return Current write mode for Slave 4 (0 = register address + data, 1 = data only)
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4WriteMode()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_REG_DIS_BIT, buffer);
+ return buffer[0];
+}
+/** Set write mode for the Slave 4.
+ * @param mode New write mode for Slave 4 (0 = register address + data, 1 = data only)
+ * @see getSlave4WriteMode()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4WriteMode(bool mode)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_REG_DIS_BIT, mode);
+}
+/** Get Slave 4 master delay value.
+ * This configures the reduced access rate of I2C slaves relative to the Sample
+ * Rate. When a slave's access rate is decreased relative to the Sample Rate,
+ * the slave is accessed every:
+ *
+ * 1 / (1 + I2C_MST_DLY) samples
+ *
+ * This base Sample Rate in turn is determined by SMPLRT_DIV (register 25) and
+ * DLPF_CFG (register 26). Whether a slave's access rate is reduced relative to
+ * the Sample Rate is determined by I2C_MST_DELAY_CTRL (register 103). For
+ * further information regarding the Sample Rate, please refer to register 25.
+ *
+ * @return Current Slave 4 master delay value
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+uint8_t MPU6050::getSlave4MasterDelay()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_MST_DLY_BIT, MPU6050_I2C_SLV4_MST_DLY_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Slave 4 master delay value.
+ * @param delay New Slave 4 master delay value
+ * @see getSlave4MasterDelay()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4MasterDelay(uint8_t delay)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_MST_DLY_BIT, MPU6050_I2C_SLV4_MST_DLY_LENGTH, delay);
+}
+/** Get last available byte read from Slave 4.
+ * This register stores the data read from Slave 4. This field is populated
+ * after a read transaction.
+ * @return Last available byte read from to Slave 4
+ * @see MPU6050_RA_I2C_SLV4_DI
+ */
+uint8_t MPU6050::getSlate4InputByte()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_I2C_SLV4_DI, buffer);
+ return buffer[0];
+}
+
+// I2C_MST_STATUS register
+
+/** Get FSYNC interrupt status.
+ * This bit reflects the status of the FSYNC interrupt from an external device
+ * into the MPU-60X0. This is used as a way to pass an external interrupt
+ * through the MPU-60X0 to the host application processor. When set to 1, this
+ * bit will cause an interrupt if FSYNC_INT_EN is asserted in INT_PIN_CFG
+ * (Register 55).
+ * @return FSYNC interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getPassthroughStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_PASS_THROUGH_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 4 transaction done status.
+ * Automatically sets to 1 when a Slave 4 transaction has completed. This
+ * triggers an interrupt if the I2C_MST_INT_EN bit in the INT_ENABLE register
+ * (Register 56) is asserted and if the SLV_4_DONE_INT bit is asserted in the
+ * I2C_SLV4_CTRL register (Register 52).
+ * @return Slave 4 transaction done status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave4IsDone()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV4_DONE_BIT, buffer);
+ return buffer[0];
+}
+/** Get master arbitration lost status.
+ * This bit automatically sets to 1 when the I2C Master has lost arbitration of
+ * the auxiliary I2C bus (an error condition). This triggers an interrupt if the
+ * I2C_MST_INT_EN bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Master arbitration lost status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getLostArbitration()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_LOST_ARB_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 4 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 4. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 4 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave4Nack()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV4_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 3 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 3. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 3 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave3Nack()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV3_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 2 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 2. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 2 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave2Nack()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV2_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 1 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 1. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 1 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave1Nack()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV1_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 0 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 0. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 0 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave0Nack()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV0_NACK_BIT, buffer);
+ return buffer[0];
+}
+
+// INT_PIN_CFG register
+
+/** Get interrupt logic level mode.
+ * Will be set 0 for active-high, 1 for active-low.
+ * @return Current interrupt mode (0=active-high, 1=active-low)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_LEVEL_BIT
+ */
+bool MPU6050::getInterruptMode()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_LEVEL_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt logic level mode.
+ * @param mode New interrupt mode (0=active-high, 1=active-low)
+ * @see getInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_LEVEL_BIT
+ */
+void MPU6050::setInterruptMode(bool mode)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_LEVEL_BIT, mode);
+}
+/** Get interrupt drive mode.
+ * Will be set 0 for push-pull, 1 for open-drain.
+ * @return Current interrupt drive mode (0=push-pull, 1=open-drain)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_OPEN_BIT
+ */
+bool MPU6050::getInterruptDrive()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_OPEN_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt drive mode.
+ * @param drive New interrupt drive mode (0=push-pull, 1=open-drain)
+ * @see getInterruptDrive()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_OPEN_BIT
+ */
+void MPU6050::setInterruptDrive(bool drive)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_OPEN_BIT, drive);
+}
+/** Get interrupt latch mode.
+ * Will be set 0 for 50us-pulse, 1 for latch-until-int-cleared.
+ * @return Current latch mode (0=50us-pulse, 1=latch-until-int-cleared)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_LATCH_INT_EN_BIT
+ */
+bool MPU6050::getInterruptLatch()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_LATCH_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt latch mode.
+ * @param latch New latch mode (0=50us-pulse, 1=latch-until-int-cleared)
+ * @see getInterruptLatch()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_LATCH_INT_EN_BIT
+ */
+void MPU6050::setInterruptLatch(bool latch)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_LATCH_INT_EN_BIT, latch);
+}
+/** Get interrupt latch clear mode.
+ * Will be set 0 for status-read-only, 1 for any-register-read.
+ * @return Current latch clear mode (0=status-read-only, 1=any-register-read)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_RD_CLEAR_BIT
+ */
+bool MPU6050::getInterruptLatchClear()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_RD_CLEAR_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt latch clear mode.
+ * @param clear New latch clear mode (0=status-read-only, 1=any-register-read)
+ * @see getInterruptLatchClear()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_RD_CLEAR_BIT
+ */
+void MPU6050::setInterruptLatchClear(bool clear)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_RD_CLEAR_BIT, clear);
+}
+/** Get FSYNC interrupt logic level mode.
+ * @return Current FSYNC interrupt mode (0=active-high, 1=active-low)
+ * @see getFSyncInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT
+ */
+bool MPU6050::getFSyncInterruptLevel()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT, buffer);
+ return buffer[0];
+}
+/** Set FSYNC interrupt logic level mode.
+ * @param mode New FSYNC interrupt mode (0=active-high, 1=active-low)
+ * @see getFSyncInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT
+ */
+void MPU6050::setFSyncInterruptLevel(bool level)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT, level);
+}
+/** Get FSYNC pin interrupt enabled setting.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled setting
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_EN_BIT
+ */
+bool MPU6050::getFSyncInterruptEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set FSYNC pin interrupt enabled setting.
+ * @param enabled New FSYNC pin interrupt enabled setting
+ * @see getFSyncInterruptEnabled()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_EN_BIT
+ */
+void MPU6050::setFSyncInterruptEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_EN_BIT, enabled);
+}
+/** Get I2C bypass enabled status.
+ * When this bit is equal to 1 and I2C_MST_EN (Register 106 bit[5]) is equal to
+ * 0, the host application processor will be able to directly access the
+ * auxiliary I2C bus of the MPU-60X0. When this bit is equal to 0, the host
+ * application processor will not be able to directly access the auxiliary I2C
+ * bus of the MPU-60X0 regardless of the state of I2C_MST_EN (Register 106
+ * bit[5]).
+ * @return Current I2C bypass enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_I2C_BYPASS_EN_BIT
+ */
+bool MPU6050::getI2CBypassEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_I2C_BYPASS_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C bypass enabled status.
+ * When this bit is equal to 1 and I2C_MST_EN (Register 106 bit[5]) is equal to
+ * 0, the host application processor will be able to directly access the
+ * auxiliary I2C bus of the MPU-60X0. When this bit is equal to 0, the host
+ * application processor will not be able to directly access the auxiliary I2C
+ * bus of the MPU-60X0 regardless of the state of I2C_MST_EN (Register 106
+ * bit[5]).
+ * @param enabled New I2C bypass enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_I2C_BYPASS_EN_BIT
+ */
+void MPU6050::setI2CBypassEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_I2C_BYPASS_EN_BIT, enabled);
+}
+/** Get reference clock output enabled status.
+ * When this bit is equal to 1, a reference clock output is provided at the
+ * CLKOUT pin. When this bit is equal to 0, the clock output is disabled. For
+ * further information regarding CLKOUT, please refer to the MPU-60X0 Product
+ * Specification document.
+ * @return Current reference clock output enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_CLKOUT_EN_BIT
+ */
+bool MPU6050::getClockOutputEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_CLKOUT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set reference clock output enabled status.
+ * When this bit is equal to 1, a reference clock output is provided at the
+ * CLKOUT pin. When this bit is equal to 0, the clock output is disabled. For
+ * further information regarding CLKOUT, please refer to the MPU-60X0 Product
+ * Specification document.
+ * @param enabled New reference clock output enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_CLKOUT_EN_BIT
+ */
+void MPU6050::setClockOutputEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_CLKOUT_EN_BIT, enabled);
+}
+
+// INT_ENABLE register
+
+/** Get full interrupt enabled status.
+ * Full register byte for all interrupts, for quick reading. Each bit will be
+ * set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+uint8_t MPU6050::getIntEnabled()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_INT_ENABLE, buffer);
+ return buffer[0];
+}
+/** Set full interrupt enabled status.
+ * Full register byte for all interrupts, for quick reading. Each bit should be
+ * set 0 for disabled, 1 for enabled.
+ * @param enabled New interrupt enabled status
+ * @see getIntFreefallEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+void MPU6050::setIntEnabled(uint8_t enabled)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_INT_ENABLE, enabled);
+}
+/** Get Free Fall interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+bool MPU6050::getIntFreefallEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FF_BIT, buffer);
+ return buffer[0];
+}
+/** Set Free Fall interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntFreefallEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+void MPU6050::setIntFreefallEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FF_BIT, enabled);
+}
+/** Get Motion Detection interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ **/
+bool MPU6050::getIntMotionEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_MOT_BIT, buffer);
+ return buffer[0];
+}
+/** Set Motion Detection interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntMotionEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ **/
+void MPU6050::setIntMotionEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_MOT_BIT, enabled);
+}
+/** Get Zero Motion Detection interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ **/
+bool MPU6050::getIntZeroMotionEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_ZMOT_BIT, buffer);
+ return buffer[0];
+}
+/** Set Zero Motion Detection interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntZeroMotionEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ **/
+void MPU6050::setIntZeroMotionEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_ZMOT_BIT, enabled);
+}
+/** Get FIFO Buffer Overflow interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ **/
+bool MPU6050::getIntFIFOBufferOverflowEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, buffer);
+ return buffer[0];
+}
+/** Set FIFO Buffer Overflow interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntFIFOBufferOverflowEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ **/
+void MPU6050::setIntFIFOBufferOverflowEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, enabled);
+}
+/** Get I2C Master interrupt enabled status.
+ * This enables any of the I2C Master interrupt sources to generate an
+ * interrupt. Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ **/
+bool MPU6050::getIntI2CMasterEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_I2C_MST_INT_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C Master interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntI2CMasterEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ **/
+void MPU6050::setIntI2CMasterEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_I2C_MST_INT_BIT, enabled);
+}
+/** Get Data Ready interrupt enabled setting.
+ * This event occurs each time a write operation to all of the sensor registers
+ * has been completed. Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+bool MPU6050::getIntDataReadyEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DATA_RDY_BIT, buffer);
+ return buffer[0];
+}
+/** Set Data Ready interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntDataReadyEnabled()
+ * @see MPU6050_RA_INT_CFG
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+void MPU6050::setIntDataReadyEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DATA_RDY_BIT, enabled);
+}
+
+// INT_STATUS register
+
+/** Get full set of interrupt status bits.
+ * These bits clear to 0 after the register has been read. Very useful
+ * for getting multiple INT statuses, since each single bit read clears
+ * all of them because it has to read the whole byte.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ */
+uint8_t MPU6050::getIntStatus()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_INT_STATUS, buffer);
+ return buffer[0];
+}
+/** Get Free Fall interrupt status.
+ * This bit automatically sets to 1 when a Free Fall interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_FF_BIT
+ */
+bool MPU6050::getIntFreefallStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_FF_BIT, buffer);
+ return buffer[0];
+}
+/** Get Motion Detection interrupt status.
+ * This bit automatically sets to 1 when a Motion Detection interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ */
+bool MPU6050::getIntMotionStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_MOT_BIT, buffer);
+ return buffer[0];
+}
+/** Get Zero Motion Detection interrupt status.
+ * This bit automatically sets to 1 when a Zero Motion Detection interrupt has
+ * been generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ */
+bool MPU6050::getIntZeroMotionStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_ZMOT_BIT, buffer);
+ return buffer[0];
+}
+/** Get FIFO Buffer Overflow interrupt status.
+ * This bit automatically sets to 1 when a Free Fall interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ */
+bool MPU6050::getIntFIFOBufferOverflowStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, buffer);
+ return buffer[0];
+}
+/** Get I2C Master interrupt status.
+ * This bit automatically sets to 1 when an I2C Master interrupt has been
+ * generated. For a list of I2C Master interrupts, please refer to Register 54.
+ * The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ */
+bool MPU6050::getIntI2CMasterStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_I2C_MST_INT_BIT, buffer);
+ return buffer[0];
+}
+/** Get Data Ready interrupt status.
+ * This bit automatically sets to 1 when a Data Ready interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+bool MPU6050::getIntDataReadyStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_DATA_RDY_BIT, buffer);
+ return buffer[0];
+}
+
+// ACCEL_*OUT_* registers
+
+/** Get raw 9-axis motion sensor readings (accel/gyro/compass).
+ * FUNCTION NOT FULLY IMPLEMENTED YET.
+ * @param ax 16-bit signed integer container for accelerometer X-axis value
+ * @param ay 16-bit signed integer container for accelerometer Y-axis value
+ * @param az 16-bit signed integer container for accelerometer Z-axis value
+ * @param gx 16-bit signed integer container for gyroscope X-axis value
+ * @param gy 16-bit signed integer container for gyroscope Y-axis value
+ * @param gz 16-bit signed integer container for gyroscope Z-axis value
+ * @param mx 16-bit signed integer container for magnetometer X-axis value
+ * @param my 16-bit signed integer container for magnetometer Y-axis value
+ * @param mz 16-bit signed integer container for magnetometer Z-axis value
+ * @see getMotion6()
+ * @see getAcceleration()
+ * @see getRotation()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+void MPU6050::getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz)
+{
+ getMotion6(ax, ay, az, gx, gy, gz);
+ // TODO: magnetometer integration
+}
+/** Get raw 6-axis motion sensor readings (accel/gyro).
+ * Retrieves all currently available motion sensor values.
+ * @param ax 16-bit signed integer container for accelerometer X-axis value
+ * @param ay 16-bit signed integer container for accelerometer Y-axis value
+ * @param az 16-bit signed integer container for accelerometer Z-axis value
+ * @param gx 16-bit signed integer container for gyroscope X-axis value
+ * @param gy 16-bit signed integer container for gyroscope Y-axis value
+ * @param gz 16-bit signed integer container for gyroscope Z-axis value
+ * @see getAcceleration()
+ * @see getRotation()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+void MPU6050::getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 14, buffer);
+ *ax = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *ay = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *az = (((int16_t)buffer[4]) << 8) | buffer[5];
+ *gx = (((int16_t)buffer[8]) << 8) | buffer[9];
+ *gy = (((int16_t)buffer[10]) << 8) | buffer[11];
+ *gz = (((int16_t)buffer[12]) << 8) | buffer[13];
+}
+/** Get 3-axis accelerometer readings.
+ * These registers store the most recent accelerometer measurements.
+ * Accelerometer measurements are written to these registers at the Sample Rate
+ * as defined in Register 25.
+ *
+ * The accelerometer measurement registers, along with the temperature
+ * measurement registers, gyroscope measurement registers, and external sensor
+ * data registers, are composed of two sets of registers: an internal register
+ * set and a user-facing read register set.
+ *
+ * The data within the accelerometer sensors' internal register set is always
+ * updated at the Sample Rate. Meanwhile, the user-facing read register set
+ * duplicates the internal register set's data values whenever the serial
+ * interface is idle. This guarantees that a burst read of sensor registers will
+ * read measurements from the same sampling instant. Note that if burst reads
+ * are not used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Each 16-bit accelerometer measurement has a full scale defined in ACCEL_FS
+ * (Register 28). For each full scale setting, the accelerometers' sensitivity
+ * per LSB in ACCEL_xOUT is shown in the table below:
+ *
+ * <pre>
+ * AFS_SEL | Full Scale Range | LSB Sensitivity
+ * --------+------------------+----------------
+ * 0 | +/- 2g | 8192 LSB/mg
+ * 1 | +/- 4g | 4096 LSB/mg
+ * 2 | +/- 8g | 2048 LSB/mg
+ * 3 | +/- 16g | 1024 LSB/mg
+ * </pre>
+ *
+ * @param x 16-bit signed integer container for X-axis acceleration
+ * @param y 16-bit signed integer container for Y-axis acceleration
+ * @param z 16-bit signed integer container for Z-axis acceleration
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+void MPU6050::getAcceleration(int16_t* x, int16_t* y, int16_t* z)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 6, buffer);
+ *x = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *y = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *z = (((int16_t)buffer[4]) << 8) | buffer[5];
+}
+/** Get X-axis accelerometer reading.
+ * @return X-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+int16_t MPU6050::getAccelerationX()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Y-axis accelerometer reading.
+ * @return Y-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_YOUT_H
+ */
+int16_t MPU6050::getAccelerationY()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ACCEL_YOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Z-axis accelerometer reading.
+ * @return Z-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_ZOUT_H
+ */
+int16_t MPU6050::getAccelerationZ()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ACCEL_ZOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// TEMP_OUT_* registers
+
+/** Get current internal temperature.
+ * @return Temperature reading in 16-bit 2's complement format
+ * @see MPU6050_RA_TEMP_OUT_H
+ */
+int16_t MPU6050::getTemperature()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_TEMP_OUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// GYRO_*OUT_* registers
+
+/** Get 3-axis gyroscope readings.
+ * These gyroscope measurement registers, along with the accelerometer
+ * measurement registers, temperature measurement registers, and external sensor
+ * data registers, are composed of two sets of registers: an internal register
+ * set and a user-facing read register set.
+ * The data within the gyroscope sensors' internal register set is always
+ * updated at the Sample Rate. Meanwhile, the user-facing read register set
+ * duplicates the internal register set's data values whenever the serial
+ * interface is idle. This guarantees that a burst read of sensor registers will
+ * read measurements from the same sampling instant. Note that if burst reads
+ * are not used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Each 16-bit gyroscope measurement has a full scale defined in FS_SEL
+ * (Register 27). For each full scale setting, the gyroscopes' sensitivity per
+ * LSB in GYRO_xOUT is shown in the table below:
+ *
+ * <pre>
+ * FS_SEL | Full Scale Range | LSB Sensitivity
+ * -------+--------------------+----------------
+ * 0 | +/- 250 degrees/s | 131 LSB/deg/s
+ * 1 | +/- 500 degrees/s | 65.5 LSB/deg/s
+ * 2 | +/- 1000 degrees/s | 32.8 LSB/deg/s
+ * 3 | +/- 2000 degrees/s | 16.4 LSB/deg/s
+ * </pre>
+ *
+ * @param x 16-bit signed integer container for X-axis rotation
+ * @param y 16-bit signed integer container for Y-axis rotation
+ * @param z 16-bit signed integer container for Z-axis rotation
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+void MPU6050::getRotation(int16_t* x, int16_t* y, int16_t* z)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_GYRO_XOUT_H, 6, buffer);
+ *x = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *y = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *z = (((int16_t)buffer[4]) << 8) | buffer[5];
+}
+/** Get X-axis gyroscope reading.
+ * @return X-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+int16_t MPU6050::getRotationX()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_GYRO_XOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Y-axis gyroscope reading.
+ * @return Y-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_YOUT_H
+ */
+int16_t MPU6050::getRotationY()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_GYRO_YOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Z-axis gyroscope reading.
+ * @return Z-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_ZOUT_H
+ */
+int16_t MPU6050::getRotationZ()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_GYRO_ZOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// EXT_SENS_DATA_* registers
+
+/** Read single byte from external sensor data register.
+ * These registers store data read from external sensors by the Slave 0, 1, 2,
+ * and 3 on the auxiliary I2C interface. Data read by Slave 4 is stored in
+ * I2C_SLV4_DI (Register 53).
+ *
+ * External sensor data is written to these registers at the Sample Rate as
+ * defined in Register 25. This access rate can be reduced by using the Slave
+ * Delay Enable registers (Register 103).
+ *
+ * External sensor data registers, along with the gyroscope measurement
+ * registers, accelerometer measurement registers, and temperature measurement
+ * registers, are composed of two sets of registers: an internal register set
+ * and a user-facing read register set.
+ *
+ * The data within the external sensors' internal register set is always updated
+ * at the Sample Rate (or the reduced access rate) whenever the serial interface
+ * is idle. This guarantees that a burst read of sensor registers will read
+ * measurements from the same sampling instant. Note that if burst reads are not
+ * used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Data is placed in these external sensor data registers according to
+ * I2C_SLV0_CTRL, I2C_SLV1_CTRL, I2C_SLV2_CTRL, and I2C_SLV3_CTRL (Registers 39,
+ * 42, 45, and 48). When more than zero bytes are read (I2C_SLVx_LEN > 0) from
+ * an enabled slave (I2C_SLVx_EN = 1), the slave is read at the Sample Rate (as
+ * defined in Register 25) or delayed rate (if specified in Register 52 and
+ * 103). During each Sample cycle, slave reads are performed in order of Slave
+ * number. If all slaves are enabled with more than zero bytes to be read, the
+ * order will be Slave 0, followed by Slave 1, Slave 2, and Slave 3.
+ *
+ * Each enabled slave will have EXT_SENS_DATA registers associated with it by
+ * number of bytes read (I2C_SLVx_LEN) in order of slave number, starting from
+ * EXT_SENS_DATA_00. Note that this means enabling or disabling a slave may
+ * change the higher numbered slaves' associated registers. Furthermore, if
+ * fewer total bytes are being read from the external sensors as a result of
+ * such a change, then the data remaining in the registers which no longer have
+ * an associated slave device (i.e. high numbered registers) will remain in
+ * these previously allocated registers unless reset.
+ *
+ * If the sum of the read lengths of all SLVx transactions exceed the number of
+ * available EXT_SENS_DATA registers, the excess bytes will be dropped. There
+ * are 24 EXT_SENS_DATA registers and hence the total read lengths between all
+ * the slaves cannot be greater than 24 or some bytes will be lost.
+ *
+ * Note: Slave 4's behavior is distinct from that of Slaves 0-3. For further
+ * information regarding the characteristics of Slave 4, please refer to
+ * Registers 49 to 53.
+ *
+ * EXAMPLE:
+ * Suppose that Slave 0 is enabled with 4 bytes to be read (I2C_SLV0_EN = 1 and
+ * I2C_SLV0_LEN = 4) while Slave 1 is enabled with 2 bytes to be read so that
+ * I2C_SLV1_EN = 1 and I2C_SLV1_LEN = 2. In such a situation, EXT_SENS_DATA _00
+ * through _03 will be associated with Slave 0, while EXT_SENS_DATA _04 and 05
+ * will be associated with Slave 1. If Slave 2 is enabled as well, registers
+ * starting from EXT_SENS_DATA_06 will be allocated to Slave 2.
+ *
+ * If Slave 2 is disabled while Slave 3 is enabled in this same situation, then
+ * registers starting from EXT_SENS_DATA_06 will be allocated to Slave 3
+ * instead.
+ *
+ * REGISTER ALLOCATION FOR DYNAMIC DISABLE VS. NORMAL DISABLE:
+ * If a slave is disabled at any time, the space initially allocated to the
+ * slave in the EXT_SENS_DATA register, will remain associated with that slave.
+ * This is to avoid dynamic adjustment of the register allocation.
+ *
+ * The allocation of the EXT_SENS_DATA registers is recomputed only when (1) all
+ * slaves are disabled, or (2) the I2C_MST_RST bit is set (Register 106).
+ *
+ * This above is also true if one of the slaves gets NACKed and stops
+ * functioning.
+ *
+ * @param position Starting position (0-23)
+ * @return Byte read from register
+ */
+uint8_t MPU6050::getExternalSensorByte(int position)
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, buffer);
+ return buffer[0];
+}
+/** Read word (2 bytes) from external sensor data registers.
+ * @param position Starting position (0-21)
+ * @return Word read from register
+ * @see getExternalSensorByte()
+ */
+uint16_t MPU6050::getExternalSensorWord(int position)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, 2, buffer);
+ return (((uint16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Read double word (4 bytes) from external sensor data registers.
+ * @param position Starting position (0-20)
+ * @return Double word read from registers
+ * @see getExternalSensorByte()
+ */
+uint32_t MPU6050::getExternalSensorDWord(int position)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, 4, buffer);
+ return (((uint32_t)buffer[0]) << 24) | (((uint32_t)buffer[1]) << 16) | (((uint16_t)buffer[2]) << 8) | buffer[3];
+}
+
+// MOT_DETECT_STATUS register
+
+/** Get X-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_XNEG_BIT
+ */
+bool MPU6050::getXNegMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_XNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get X-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_XPOS_BIT
+ */
+bool MPU6050::getXPosMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_XPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get Y-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_YNEG_BIT
+ */
+bool MPU6050::getYNegMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_YNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get Y-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_YPOS_BIT
+ */
+bool MPU6050::getYPosMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_YPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get Z-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZNEG_BIT
+ */
+bool MPU6050::getZNegMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get Z-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZPOS_BIT
+ */
+bool MPU6050::getZPosMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get zero motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZRMOT_BIT
+ */
+bool MPU6050::getZeroMotionDetected()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZRMOT_BIT, buffer);
+ return buffer[0];
+}
+
+// I2C_SLV*_DO register
+
+/** Write byte to Data Output container for specified slave.
+ * This register holds the output data written into Slave when Slave is set to
+ * write mode. For further information regarding Slave control, please
+ * refer to Registers 37 to 39 and immediately following.
+ * @param num Slave number (0-3)
+ * @param data Byte to write
+ * @see MPU6050_RA_I2C_SLV0_DO
+ */
+void MPU6050::setSlaveOutputByte(uint8_t num, uint8_t data)
+{
+ if (num > 3) return;
+ i2Cdev.writeByte(devAddr, MPU6050_RA_I2C_SLV0_DO + num, data);
+}
+
+// I2C_MST_DELAY_CTRL register
+
+/** Get external data shadow delay enabled status.
+ * This register is used to specify the timing of external sensor data
+ * shadowing. When DELAY_ES_SHADOW is set to 1, shadowing of external
+ * sensor data is delayed until all data has been received.
+ * @return Current external data shadow delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT
+ */
+bool MPU6050::getExternalShadowDelayEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT, buffer);
+ return buffer[0];
+}
+/** Set external data shadow delay enabled status.
+ * @param enabled New external data shadow delay enabled status.
+ * @see getExternalShadowDelayEnabled()
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT
+ */
+void MPU6050::setExternalShadowDelayEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT, enabled);
+}
+/** Get slave delay enabled status.
+ * When a particular slave delay is enabled, the rate of access for the that
+ * slave device is reduced. When a slave's access rate is decreased relative to
+ * the Sample Rate, the slave is accessed every:
+ *
+ * 1 / (1 + I2C_MST_DLY) Samples
+ *
+ * This base Sample Rate in turn is determined by SMPLRT_DIV (register * 25)
+ * and DLPF_CFG (register 26).
+ *
+ * For further information regarding I2C_MST_DLY, please refer to register 52.
+ * For further information regarding the Sample Rate, please refer to register 25.
+ *
+ * @param num Slave number (0-4)
+ * @return Current slave delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT
+ */
+bool MPU6050::getSlaveDelayEnabled(uint8_t num)
+{
+ // MPU6050_DELAYCTRL_I2C_SLV4_DLY_EN_BIT is 4, SLV3 is 3, etc.
+ if (num > 4) return 0;
+ i2Cdev.readBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, num, buffer);
+ return buffer[0];
+}
+/** Set slave delay enabled status.
+ * @param num Slave number (0-4)
+ * @param enabled New slave delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT
+ */
+void MPU6050::setSlaveDelayEnabled(uint8_t num, bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, num, enabled);
+}
+
+// SIGNAL_PATH_RESET register
+
+/** Reset gyroscope signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_GYRO_RESET_BIT
+ */
+void MPU6050::resetGyroscopePath()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_GYRO_RESET_BIT, true);
+}
+/** Reset accelerometer signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_ACCEL_RESET_BIT
+ */
+void MPU6050::resetAccelerometerPath()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_ACCEL_RESET_BIT, true);
+}
+/** Reset temperature sensor signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_TEMP_RESET_BIT
+ */
+void MPU6050::resetTemperaturePath()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_TEMP_RESET_BIT, true);
+}
+
+// MOT_DETECT_CTRL register
+
+/** Get accelerometer power-on delay.
+ * The accelerometer data path provides samples to the sensor registers, Motion
+ * detection, Zero Motion detection, and Free Fall detection modules. The
+ * signal path contains filters which must be flushed on wake-up with new
+ * samples before the detection modules begin operations. The default wake-up
+ * delay, of 4ms can be lengthened by up to 3ms. This additional delay is
+ * specified in ACCEL_ON_DELAY in units of 1 LSB = 1 ms. The user may select
+ * any value above zero unless instructed otherwise by InvenSense. Please refer
+ * to Section 8 of the MPU-6000/MPU-6050 Product Specification document for
+ * further information regarding the detection modules.
+ * @return Current accelerometer power-on delay
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_ACCEL_ON_DELAY_BIT
+ */
+uint8_t MPU6050::getAccelerometerPowerOnDelay()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_ACCEL_ON_DELAY_BIT, MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set accelerometer power-on delay.
+ * @param delay New accelerometer power-on delay (0-3)
+ * @see getAccelerometerPowerOnDelay()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_ACCEL_ON_DELAY_BIT
+ */
+void MPU6050::setAccelerometerPowerOnDelay(uint8_t delay)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_ACCEL_ON_DELAY_BIT, MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH, delay);
+}
+/** Get Free Fall detection counter decrement configuration.
+ * Detection is registered by the Free Fall detection module after accelerometer
+ * measurements meet their respective threshold conditions over a specified
+ * number of samples. When the threshold conditions are met, the corresponding
+ * detection counter increments by 1. The user may control the rate at which the
+ * detection counter decrements when the threshold condition is not met by
+ * configuring FF_COUNT. The decrement rate can be set according to the
+ * following table:
+ *
+ * <pre>
+ * FF_COUNT | Counter Decrement
+ * ---------+------------------
+ * 0 | Reset
+ * 1 | 1
+ * 2 | 2
+ * 3 | 4
+ * </pre>
+ *
+ * When FF_COUNT is configured to 0 (reset), any non-qualifying sample will
+ * reset the counter to 0. For further information on Free Fall detection,
+ * please refer to Registers 29 to 32.
+ *
+ * @return Current decrement configuration
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_FF_COUNT_BIT
+ */
+uint8_t MPU6050::getFreefallDetectionCounterDecrement()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_FF_COUNT_BIT, MPU6050_DETECT_FF_COUNT_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Free Fall detection counter decrement configuration.
+ * @param decrement New decrement configuration value
+ * @see getFreefallDetectionCounterDecrement()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_FF_COUNT_BIT
+ */
+void MPU6050::setFreefallDetectionCounterDecrement(uint8_t decrement)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_FF_COUNT_BIT, MPU6050_DETECT_FF_COUNT_LENGTH, decrement);
+}
+/** Get Motion detection counter decrement configuration.
+ * Detection is registered by the Motion detection module after accelerometer
+ * measurements meet their respective threshold conditions over a specified
+ * number of samples. When the threshold conditions are met, the corresponding
+ * detection counter increments by 1. The user may control the rate at which the
+ * detection counter decrements when the threshold condition is not met by
+ * configuring MOT_COUNT. The decrement rate can be set according to the
+ * following table:
+ *
+ * <pre>
+ * MOT_COUNT | Counter Decrement
+ * ----------+------------------
+ * 0 | Reset
+ * 1 | 1
+ * 2 | 2
+ * 3 | 4
+ * </pre>
+ *
+ * When MOT_COUNT is configured to 0 (reset), any non-qualifying sample will
+ * reset the counter to 0. For further information on Motion detection,
+ * please refer to Registers 29 to 32.
+ *
+ */
+uint8_t MPU6050::getMotionDetectionCounterDecrement()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_MOT_COUNT_BIT, MPU6050_DETECT_MOT_COUNT_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Motion detection counter decrement configuration.
+ * @param decrement New decrement configuration value
+ * @see getMotionDetectionCounterDecrement()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_MOT_COUNT_BIT
+ */
+void MPU6050::setMotionDetectionCounterDecrement(uint8_t decrement)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_MOT_COUNT_BIT, MPU6050_DETECT_MOT_COUNT_LENGTH, decrement);
+}
+
+// USER_CTRL register
+
+/** Get FIFO enabled status.
+ * When this bit is set to 0, the FIFO buffer is disabled. The FIFO buffer
+ * cannot be written to or read from while disabled. The FIFO buffer's state
+ * does not change unless the MPU-60X0 is power cycled.
+ * @return Current FIFO enabled status
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_EN_BIT
+ */
+bool MPU6050::getFIFOEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set FIFO enabled status.
+ * @param enabled New FIFO enabled status
+ * @see getFIFOEnabled()
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_EN_BIT
+ */
+void MPU6050::setFIFOEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_EN_BIT, enabled);
+}
+/** Get I2C Master Mode enabled status.
+ * When this mode is enabled, the MPU-60X0 acts as the I2C Master to the
+ * external sensor slave devices on the auxiliary I2C bus. When this bit is
+ * cleared to 0, the auxiliary I2C bus lines (AUX_DA and AUX_CL) are logically
+ * driven by the primary I2C bus (SDA and SCL). This is a precondition to
+ * enabling Bypass Mode. For further information regarding Bypass Mode, please
+ * refer to Register 55.
+ * @return Current I2C Master Mode enabled status
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_EN_BIT
+ */
+bool MPU6050::getI2CMasterModeEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C Master Mode enabled status.
+ * @param enabled New I2C Master Mode enabled status
+ * @see getI2CMasterModeEnabled()
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_EN_BIT
+ */
+void MPU6050::setI2CMasterModeEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_EN_BIT, enabled);
+}
+/** Switch from I2C to SPI mode (MPU-6000 only)
+ * If this is set, the primary SPI interface will be enabled in place of the
+ * disabled primary I2C interface.
+ */
+void MPU6050::switchSPIEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_IF_DIS_BIT, enabled);
+}
+/** Reset the FIFO.
+ * This bit resets the FIFO buffer when set to 1 while FIFO_EN equals 0. This
+ * bit automatically clears to 0 after the reset has been triggered.
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_RESET_BIT
+ */
+void MPU6050::resetFIFO()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_RESET_BIT, true);
+}
+/** Reset the I2C Master.
+ * This bit resets the I2C Master when set to 1 while I2C_MST_EN equals 0.
+ * This bit automatically clears to 0 after the reset has been triggered.
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_RESET_BIT
+ */
+void MPU6050::resetI2CMaster()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_RESET_BIT, true);
+}
+/** Reset all sensor registers and signal paths.
+ * When set to 1, this bit resets the signal paths for all sensors (gyroscopes,
+ * accelerometers, and temperature sensor). This operation will also clear the
+ * sensor registers. This bit automatically clears to 0 after the reset has been
+ * triggered.
+ *
+ * When resetting only the signal path (and not the sensor registers), please
+ * use Register 104, SIGNAL_PATH_RESET.
+ *
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_SIG_COND_RESET_BIT
+ */
+void MPU6050::resetSensors()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_SIG_COND_RESET_BIT, true);
+}
+
+// PWR_MGMT_1 register
+
+/** Trigger a full device reset.
+ * A small delay of ~50ms may be desirable after triggering a reset.
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_DEVICE_RESET_BIT
+ */
+void MPU6050::reset()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_DEVICE_RESET_BIT, true);
+}
+/** Get sleep mode status.
+ * Setting the SLEEP bit in the register puts the device into very low power
+ * sleep mode. In this mode, only the serial interface and internal registers
+ * remain active, allowing for a very low standby current. Clearing this bit
+ * puts the device back into normal mode. To save power, the individual standby
+ * selections for each of the gyros should be used if any gyro axis is not used
+ * by the application.
+ * @return Current sleep mode enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_SLEEP_BIT
+ */
+bool MPU6050::getSleepEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_SLEEP_BIT, buffer);
+ return buffer[0];
+}
+/** Set sleep mode status.
+ * @param enabled New sleep mode enabled status
+ * @see getSleepEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_SLEEP_BIT
+ */
+void MPU6050::setSleepEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_SLEEP_BIT, enabled);
+}
+/** Get wake cycle enabled status.
+ * When this bit is set to 1 and SLEEP is disabled, the MPU-60X0 will cycle
+ * between sleep mode and waking up to take a single sample of data from active
+ * sensors at a rate determined by LP_WAKE_CTRL (register 108).
+ * @return Current sleep mode enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CYCLE_BIT
+ */
+bool MPU6050::getWakeCycleEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CYCLE_BIT, buffer);
+ return buffer[0];
+}
+/** Set wake cycle enabled status.
+ * @param enabled New sleep mode enabled status
+ * @see getWakeCycleEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CYCLE_BIT
+ */
+void MPU6050::setWakeCycleEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CYCLE_BIT, enabled);
+}
+/** Get temperature sensor enabled status.
+ * Control the usage of the internal temperature sensor.
+ *
+ * Note: this register stores the *disabled* value, but for consistency with the
+ * rest of the code, the function is named and used with standard true/false
+ * values to indicate whether the sensor is enabled or disabled, respectively.
+ *
+ * @return Current temperature sensor enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_TEMP_DIS_BIT
+ */
+bool MPU6050::getTempSensorEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_TEMP_DIS_BIT, buffer);
+ return buffer[0] == 0; // 1 is actually disabled here
+}
+/** Set temperature sensor enabled status.
+ * Note: this register stores the *disabled* value, but for consistency with the
+ * rest of the code, the function is named and used with standard true/false
+ * values to indicate whether the sensor is enabled or disabled, respectively.
+ *
+ * @param enabled New temperature sensor enabled status
+ * @see getTempSensorEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_TEMP_DIS_BIT
+ */
+void MPU6050::setTempSensorEnabled(bool enabled)
+{
+ // 1 is actually disabled here
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_TEMP_DIS_BIT, !enabled);
+}
+/** Get clock source setting.
+ * @return Current clock source setting
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CLKSEL_BIT
+ * @see MPU6050_PWR1_CLKSEL_LENGTH
+ */
+uint8_t MPU6050::getClockSource()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CLKSEL_BIT, MPU6050_PWR1_CLKSEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set clock source setting.
+ * An internal 8MHz oscillator, gyroscope based clock, or external sources can
+ * be selected as the MPU-60X0 clock source. When the internal 8 MHz oscillator
+ * or an external source is chosen as the clock source, the MPU-60X0 can operate
+ * in low power modes with the gyroscopes disabled.
+ *
+ * Upon power up, the MPU-60X0 clock source defaults to the internal oscillator.
+ * However, it is highly recommended that the device be configured to use one of
+ * the gyroscopes (or an external clock source) as the clock reference for
+ * improved stability. The clock source can be selected according to the following table:
+ *
+ * <pre>
+ * CLK_SEL | Clock Source
+ * --------+--------------------------------------
+ * 0 | Internal oscillator
+ * 1 | PLL with X Gyro reference
+ * 2 | PLL with Y Gyro reference
+ * 3 | PLL with Z Gyro reference
+ * 4 | PLL with external 32.768kHz reference
+ * 5 | PLL with external 19.2MHz reference
+ * 6 | Reserved
+ * 7 | Stops the clock and keeps the timing generator in reset
+ * </pre>
+ *
+ * @param source New clock source setting
+ * @see getClockSource()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CLKSEL_BIT
+ * @see MPU6050_PWR1_CLKSEL_LENGTH
+ */
+void MPU6050::setClockSource(uint8_t source)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CLKSEL_BIT, MPU6050_PWR1_CLKSEL_LENGTH, source);
+}
+
+// PWR_MGMT_2 register
+
+/** Get wake frequency in Accel-Only Low Power Mode.
+ * The MPU-60X0 can be put into Accerlerometer Only Low Power Mode by setting
+ * PWRSEL to 1 in the Power Management 1 register (Register 107). In this mode,
+ * the device will power off all devices except for the primary I2C interface,
+ * waking only the accelerometer at fixed intervals to take a single
+ * measurement. The frequency of wake-ups can be configured with LP_WAKE_CTRL
+ * as shown below:
+ *
+ * <pre>
+ * LP_WAKE_CTRL | Wake-up Frequency
+ * -------------+------------------
+ * 0 | 1.25 Hz
+ * 1 | 2.5 Hz
+ * 2 | 5 Hz
+ * 3 | 10 Hz
+ * <pre>
+ *
+ * For further information regarding the MPU-60X0's power modes, please refer to
+ * Register 107.
+ *
+ * @return Current wake frequency
+ * @see MPU6050_RA_PWR_MGMT_2
+ */
+uint8_t MPU6050::getWakeFrequency()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_LP_WAKE_CTRL_BIT, MPU6050_PWR2_LP_WAKE_CTRL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set wake frequency in Accel-Only Low Power Mode.
+ * @param frequency New wake frequency
+ * @see MPU6050_RA_PWR_MGMT_2
+ */
+void MPU6050::setWakeFrequency(uint8_t frequency)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_LP_WAKE_CTRL_BIT, MPU6050_PWR2_LP_WAKE_CTRL_LENGTH, frequency);
+}
+
+/** Get X-axis accelerometer standby enabled status.
+ * If enabled, the X-axis will not gather or report data (or use power).
+ * @return Current X-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XA_BIT
+ */
+bool MPU6050::getStandbyXAccelEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XA_BIT, buffer);
+ return buffer[0];
+}
+/** Set X-axis accelerometer standby enabled status.
+ * @param New X-axis standby enabled status
+ * @see getStandbyXAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XA_BIT
+ */
+void MPU6050::setStandbyXAccelEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XA_BIT, enabled);
+}
+/** Get Y-axis accelerometer standby enabled status.
+ * If enabled, the Y-axis will not gather or report data (or use power).
+ * @return Current Y-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YA_BIT
+ */
+bool MPU6050::getStandbyYAccelEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YA_BIT, buffer);
+ return buffer[0];
+}
+/** Set Y-axis accelerometer standby enabled status.
+ * @param New Y-axis standby enabled status
+ * @see getStandbyYAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YA_BIT
+ */
+void MPU6050::setStandbyYAccelEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YA_BIT, enabled);
+}
+/** Get Z-axis accelerometer standby enabled status.
+ * If enabled, the Z-axis will not gather or report data (or use power).
+ * @return Current Z-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZA_BIT
+ */
+bool MPU6050::getStandbyZAccelEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZA_BIT, buffer);
+ return buffer[0];
+}
+/** Set Z-axis accelerometer standby enabled status.
+ * @param New Z-axis standby enabled status
+ * @see getStandbyZAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZA_BIT
+ */
+void MPU6050::setStandbyZAccelEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZA_BIT, enabled);
+}
+/** Get X-axis gyroscope standby enabled status.
+ * If enabled, the X-axis will not gather or report data (or use power).
+ * @return Current X-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XG_BIT
+ */
+bool MPU6050::getStandbyXGyroEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XG_BIT, buffer);
+ return buffer[0];
+}
+/** Set X-axis gyroscope standby enabled status.
+ * @param New X-axis standby enabled status
+ * @see getStandbyXGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XG_BIT
+ */
+void MPU6050::setStandbyXGyroEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XG_BIT, enabled);
+}
+/** Get Y-axis gyroscope standby enabled status.
+ * If enabled, the Y-axis will not gather or report data (or use power).
+ * @return Current Y-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YG_BIT
+ */
+bool MPU6050::getStandbyYGyroEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YG_BIT, buffer);
+ return buffer[0];
+}
+/** Set Y-axis gyroscope standby enabled status.
+ * @param New Y-axis standby enabled status
+ * @see getStandbyYGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YG_BIT
+ */
+void MPU6050::setStandbyYGyroEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YG_BIT, enabled);
+}
+/** Get Z-axis gyroscope standby enabled status.
+ * If enabled, the Z-axis will not gather or report data (or use power).
+ * @return Current Z-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZG_BIT
+ */
+bool MPU6050::getStandbyZGyroEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZG_BIT, buffer);
+ return buffer[0];
+}
+/** Set Z-axis gyroscope standby enabled status.
+ * @param New Z-axis standby enabled status
+ * @see getStandbyZGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZG_BIT
+ */
+void MPU6050::setStandbyZGyroEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZG_BIT, enabled);
+}
+
+// FIFO_COUNT* registers
+
+/** Get current FIFO buffer size.
+ * This value indicates the number of bytes stored in the FIFO buffer. This
+ * number is in turn the number of bytes that can be read from the FIFO buffer
+ * and it is directly proportional to the number of samples available given the
+ * set of sensor data bound to be stored in the FIFO (register 35 and 36).
+ * @return Current FIFO buffer size
+ */
+uint16_t MPU6050::getFIFOCount()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_FIFO_COUNTH, 2, buffer);
+ return (((uint16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// FIFO_R_W register
+
+/** Get byte from FIFO buffer.
+ * This register is used to read and write data from the FIFO buffer. Data is
+ * written to the FIFO in order of register number (from lowest to highest). If
+ * all the FIFO enable flags (see below) are enabled and all External Sensor
+ * Data registers (Registers 73 to 96) are associated with a Slave device, the
+ * contents of registers 59 through 96 will be written in order at the Sample
+ * Rate.
+ *
+ * The contents of the sensor data registers (Registers 59 to 96) are written
+ * into the FIFO buffer when their corresponding FIFO enable flags are set to 1
+ * in FIFO_EN (Register 35). An additional flag for the sensor data registers
+ * associated with I2C Slave 3 can be found in I2C_MST_CTRL (Register 36).
+ *
+ * If the FIFO buffer has overflowed, the status bit FIFO_OFLOW_INT is
+ * automatically set to 1. This bit is located in INT_STATUS (Register 58).
+ * When the FIFO buffer has overflowed, the oldest data will be lost and new
+ * data will be written to the FIFO.
+ *
+ * If the FIFO buffer is empty, reading this register will return the last byte
+ * that was previously read from the FIFO until new data is available. The user
+ * should check FIFO_COUNT to ensure that the FIFO buffer is not read when
+ * empty.
+ *
+ * @return Byte from FIFO buffer
+ */
+uint8_t MPU6050::getFIFOByte()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_FIFO_R_W, buffer);
+ return buffer[0];
+}
+void MPU6050::getFIFOBytes(uint8_t *data, uint8_t length)
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_FIFO_R_W, length, data);
+}
+/** Write byte to FIFO buffer.
+ * @see getFIFOByte()
+ * @see MPU6050_RA_FIFO_R_W
+ */
+void MPU6050::setFIFOByte(uint8_t data)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_FIFO_R_W, data);
+}
+
+// WHO_AM_I register
+
+/** Get Device ID.
+ * This register is used to verify the identity of the device (0b110100, 0x34).
+ * @return Device ID (6 bits only! should be 0x34)
+ * @see MPU6050_RA_WHO_AM_I
+ * @see MPU6050_WHO_AM_I_BIT
+ * @see MPU6050_WHO_AM_I_LENGTH
+ */
+uint8_t MPU6050::getDeviceID()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_WHO_AM_I, MPU6050_WHO_AM_I_BIT, MPU6050_WHO_AM_I_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Device ID.
+ * Write a new ID into the WHO_AM_I register (no idea why this should ever be
+ * necessary though).
+ * @param id New device ID to set.
+ * @see getDeviceID()
+ * @see MPU6050_RA_WHO_AM_I
+ * @see MPU6050_WHO_AM_I_BIT
+ * @see MPU6050_WHO_AM_I_LENGTH
+ */
+void MPU6050::setDeviceID(uint8_t id)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_WHO_AM_I, MPU6050_WHO_AM_I_BIT, MPU6050_WHO_AM_I_LENGTH, id);
+}
+
+// ======== UNDOCUMENTED/DMP REGISTERS/METHODS ========
+
+// XG_OFFS_TC register
+
+uint8_t MPU6050::getOTPBankValid()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OTP_BNK_VLD_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setOTPBankValid(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OTP_BNK_VLD_BIT, enabled);
+}
+int8_t MPU6050::getXGyroOffset()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setXGyroOffset(int8_t offset)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// YG_OFFS_TC register
+
+int8_t MPU6050::getYGyroOffset()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setYGyroOffset(int8_t offset)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// ZG_OFFS_TC register
+
+int8_t MPU6050::getZGyroOffset()
+{
+ i2Cdev.readBits(devAddr, MPU6050_RA_ZG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setZGyroOffset(int8_t offset)
+{
+ i2Cdev.writeBits(devAddr, MPU6050_RA_ZG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// X_FINE_GAIN register
+
+int8_t MPU6050::getXFineGain()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_X_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setXFineGain(int8_t gain)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_X_FINE_GAIN, gain);
+}
+
+// Y_FINE_GAIN register
+
+int8_t MPU6050::getYFineGain()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_Y_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setYFineGain(int8_t gain)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_Y_FINE_GAIN, gain);
+}
+
+// Z_FINE_GAIN register
+
+int8_t MPU6050::getZFineGain()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_Z_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setZFineGain(int8_t gain)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_Z_FINE_GAIN, gain);
+}
+
+// XA_OFFS_* registers
+
+int16_t MPU6050::getXAccelOffset()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_XA_OFFS_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setXAccelOffset(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_XA_OFFS_H, offset);
+}
+
+// YA_OFFS_* register
+
+int16_t MPU6050::getYAccelOffset()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_YA_OFFS_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setYAccelOffset(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_YA_OFFS_H, offset);
+}
+
+// ZA_OFFS_* register
+
+int16_t MPU6050::getZAccelOffset()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ZA_OFFS_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setZAccelOffset(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_ZA_OFFS_H, offset);
+}
+
+// XG_OFFS_USR* registers
+
+int16_t MPU6050::getXGyroOffsetUser()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_XG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setXGyroOffsetUser(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_XG_OFFS_USRH, offset);
+}
+
+// YG_OFFS_USR* register
+
+int16_t MPU6050::getYGyroOffsetUser()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_YG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setYGyroOffsetUser(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_YG_OFFS_USRH, offset);
+}
+
+// ZG_OFFS_USR* register
+
+int16_t MPU6050::getZGyroOffsetUser()
+{
+ i2Cdev.readBytes(devAddr, MPU6050_RA_ZG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setZGyroOffsetUser(int16_t offset)
+{
+ i2Cdev.writeWord(devAddr, MPU6050_RA_ZG_OFFS_USRH, offset);
+}
+
+// INT_ENABLE register (DMP functions)
+
+bool MPU6050::getIntPLLReadyEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setIntPLLReadyEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, enabled);
+}
+bool MPU6050::getIntDMPEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DMP_INT_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setIntDMPEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DMP_INT_BIT, enabled);
+}
+
+// DMP_INT_STATUS
+
+bool MPU6050::getDMPInt5Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_5_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt4Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_4_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt3Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_3_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt2Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_2_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt1Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_1_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt0Status()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_0_BIT, buffer);
+ return buffer[0];
+}
+
+// INT_STATUS register (DMP functions)
+
+bool MPU6050::getIntPLLReadyStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getIntDMPStatus()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_DMP_INT_BIT, buffer);
+ return buffer[0];
+}
+
+// USER_CTRL register (DMP functions)
+
+bool MPU6050::getDMPEnabled()
+{
+ i2Cdev.readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_EN_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPEnabled(bool enabled)
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_EN_BIT, enabled);
+}
+void MPU6050::resetDMP()
+{
+ i2Cdev.writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_RESET_BIT, true);
+}
+
+// BANK_SEL register
+
+void MPU6050::setMemoryBank(uint8_t bank, bool prefetchEnabled, bool userBank)
+{
+ bank &= 0x1F;
+ if (userBank) bank |= 0x20;
+ if (prefetchEnabled) bank |= 0x40;
+ i2Cdev.writeByte(devAddr, MPU6050_RA_BANK_SEL, bank);
+}
+
+// MEM_START_ADDR register
+
+void MPU6050::setMemoryStartAddress(uint8_t address)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_MEM_START_ADDR, address);
+}
+
+// MEM_R_W register
+
+uint8_t MPU6050::readMemoryByte()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_MEM_R_W, buffer);
+ return buffer[0];
+}
+void MPU6050::writeMemoryByte(uint8_t data)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_MEM_R_W, data);
+}
+void MPU6050::readMemoryBlock(uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address)
+{
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ uint8_t chunkSize;
+ for (uint16_t i = 0; i < dataSize;) {
+ // determine correct chunk size according to bank position and data size
+ chunkSize = MPU6050_DMP_MEMORY_CHUNK_SIZE;
+
+ // make sure we don't go past the data size
+ if (i + chunkSize > dataSize) chunkSize = dataSize - i;
+
+ // make sure this chunk doesn't go past the bank boundary (256 bytes)
+ if (chunkSize > 256 - address) chunkSize = 256 - address;
+
+ // read the chunk of data as specified
+ i2Cdev.readBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, data + i);
+
+ // increase byte index by [chunkSize]
+ i += chunkSize;
+
+ // uint8_t automatically wraps to 0 at 256
+ address += chunkSize;
+
+ // if we aren't done, update bank (if necessary) and address
+ if (i < dataSize) {
+ if (address == 0) bank++;
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ }
+ }
+}
+bool MPU6050::writeMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address, bool verify, bool useProgMem)
+{
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ uint8_t chunkSize;
+ uint8_t *verifyBuffer;
+ uint8_t *progBuffer;
+ uint16_t i;
+ uint8_t j;
+ if (verify) verifyBuffer = (uint8_t *)malloc(MPU6050_DMP_MEMORY_CHUNK_SIZE);
+ if (useProgMem) progBuffer = (uint8_t *)malloc(MPU6050_DMP_MEMORY_CHUNK_SIZE);
+ for (i = 0; i < dataSize;) {
+ // determine correct chunk size according to bank position and data size
+ chunkSize = MPU6050_DMP_MEMORY_CHUNK_SIZE;
+
+ // make sure we don't go past the data size
+ if (i + chunkSize > dataSize) chunkSize = dataSize - i;
+
+ // make sure this chunk doesn't go past the bank boundary (256 bytes)
+ if (chunkSize > 256 - address) chunkSize = 256 - address;
+
+ if (useProgMem) {
+ // write the chunk of data as specified
+ for (j = 0; j < chunkSize; j++) progBuffer[j] = pgm_read_byte(data + i + j);
+ } else {
+ // write the chunk of data as specified
+ progBuffer = (uint8_t *)data + i;
+ }
+
+ i2Cdev.writeBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, progBuffer);
+
+ // verify data if needed
+ if (verify && verifyBuffer) {
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ i2Cdev.readBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, verifyBuffer);
+ if (memcmp(progBuffer, verifyBuffer, chunkSize) != 0) {
+ /*Serial.print("Block write verification error, bank ");
+ Serial.print(bank, DEC);
+ Serial.print(", address ");
+ Serial.print(address, DEC);
+ Serial.print("!\nExpected:");
+ for (j = 0; j < chunkSize; j++) {
+ Serial.print(" 0x");
+ if (progBuffer[j] < 16) Serial.print("0");
+ Serial.print(progBuffer[j], HEX);
+ }
+ Serial.print("\nReceived:");
+ for (uint8_t j = 0; j < chunkSize; j++) {
+ Serial.print(" 0x");
+ if (verifyBuffer[i + j] < 16) Serial.print("0");
+ Serial.print(verifyBuffer[i + j], HEX);
+ }
+ Serial.print("\n");*/
+ free(verifyBuffer);
+ if (useProgMem) free(progBuffer);
+ return false; // uh oh.
+ }
+ }
+
+ // increase byte index by [chunkSize]
+ i += chunkSize;
+
+ // uint8_t automatically wraps to 0 at 256
+ address += chunkSize;
+
+ // if we aren't done, update bank (if necessary) and address
+ if (i < dataSize) {
+ if (address == 0) bank++;
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ }
+ }
+ if (verify) free(verifyBuffer);
+ if (useProgMem) free(progBuffer);
+ return true;
+}
+bool MPU6050::writeProgMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address, bool verify)
+{
+ return writeMemoryBlock(data, dataSize, bank, address, verify, true);
+}
+bool MPU6050::writeDMPConfigurationSet(const uint8_t *data, uint16_t dataSize, bool useProgMem)
+{
+ uint8_t *progBuffer, success, special;
+ uint16_t i, j;
+ if (useProgMem) {
+ progBuffer = (uint8_t *)malloc(8); // assume 8-byte blocks, realloc later if necessary
+ }
+
+ // config set data is a long string of blocks with the following structure:
+ // [bank] [offset] [length] [byte[0], byte[1], ..., byte[length]]
+ uint8_t bank, offset, length;
+ for (i = 0; i < dataSize;) {
+ if (useProgMem) {
+ bank = pgm_read_byte(data + i++);
+ offset = pgm_read_byte(data + i++);
+ length = pgm_read_byte(data + i++);
+ } else {
+ bank = data[i++];
+ offset = data[i++];
+ length = data[i++];
+ }
+
+ // write data or perform special action
+ if (length > 0) {
+ // regular block of data to write
+ /*Serial.print("Writing config block to bank ");
+ Serial.print(bank);
+ Serial.print(", offset ");
+ Serial.print(offset);
+ Serial.print(", length=");
+ Serial.println(length);*/
+ if (useProgMem) {
+ if (sizeof(progBuffer) < length) progBuffer = (uint8_t *)realloc(progBuffer, length);
+ for (j = 0; j < length; j++) progBuffer[j] = pgm_read_byte(data + i + j);
+ } else {
+ progBuffer = (uint8_t *)data + i;
+ }
+ success = writeMemoryBlock(progBuffer, length, bank, offset, true);
+ i += length;
+ } else {
+ // special instruction
+ // NOTE: this kind of behavior (what and when to do certain things)
+ // is totally undocumented. This code is in here based on observed
+ // behavior only, and exactly why (or even whether) it has to be here
+ // is anybody's guess for now.
+ if (useProgMem) {
+ special = pgm_read_byte(data + i++);
+ } else {
+ special = data[i++];
+ }
+ /*Serial.print("Special command code ");
+ Serial.print(special, HEX);
+ Serial.println(" found...");*/
+ if (special == 0x01) {
+ // enable DMP-related interrupts
+
+ //setIntZeroMotionEnabled(true);
+ //setIntFIFOBufferOverflowEnabled(true);
+ //setIntDMPEnabled(true);
+ i2Cdev.writeByte(devAddr, MPU6050_RA_INT_ENABLE, 0x32); // single operation
+
+ success = true;
+ } else {
+ // unknown special command
+ success = false;
+ }
+ }
+
+ if (!success) {
+ if (useProgMem) free(progBuffer);
+ return false; // uh oh
+ }
+ }
+ if (useProgMem) free(progBuffer);
+ return true;
+}
+bool MPU6050::writeProgDMPConfigurationSet(const uint8_t *data, uint16_t dataSize)
+{
+ return writeDMPConfigurationSet(data, dataSize, false);
+}
+
+// DMP_CFG_1 register
+
+uint8_t MPU6050::getDMPConfig1()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_DMP_CFG_1, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPConfig1(uint8_t config)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_DMP_CFG_1, config);
+}
+
+// DMP_CFG_2 register
+
+uint8_t MPU6050::getDMPConfig2()
+{
+ i2Cdev.readByte(devAddr, MPU6050_RA_DMP_CFG_2, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPConfig2(uint8_t config)
+{
+ i2Cdev.writeByte(devAddr, MPU6050_RA_DMP_CFG_2, config);
+}
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/MPU6050.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,995 @@
+//ported from arduino library: https://github.com/jrowberg/i2cdevlib/tree/master/Arduino/MPU6050
+//written by szymon gaertig (email: szymon@gaertig.com.pl)
+//
+//Changelog:
+//2013-01-08 - first beta release
+
+// I2Cdev library collection - MPU6050 I2C device class
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 10/3/2011 by Jeff Rowberg <jeff@rowberg.net>
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// ... - ongoing debug release
+
+// NOTE: THIS IS ONLY A PARIAL RELEASE. THIS DEVICE CLASS IS CURRENTLY UNDERGOING ACTIVE
+// DEVELOPMENT AND IS STILL MISSING SOME IMPORTANT FEATURES. PLEASE KEEP THIS IN MIND IF
+// YOU DECIDE TO USE THIS PARTICULAR CODE FOR ANYTHING.
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _MPU6050_H_
+#define _MPU6050_H_
+
+#include "I2Cdev.h"
+#include "helper_3dmath.h"
+
+#define MPU6050_ADDRESS_AD0_LOW 0x68 // address pin low (GND), default for InvenSense evaluation board
+#define MPU6050_ADDRESS_AD0_HIGH 0x69 // address pin high (VCC)
+#define MPU6050_DEFAULT_ADDRESS MPU6050_ADDRESS_AD0_LOW
+
+#define MPU6050_RA_XG_OFFS_TC 0x00 //[7] PWR_MODE, [6:1] XG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_YG_OFFS_TC 0x01 //[7] PWR_MODE, [6:1] YG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_ZG_OFFS_TC 0x02 //[7] PWR_MODE, [6:1] ZG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_X_FINE_GAIN 0x03 //[7:0] X_FINE_GAIN
+#define MPU6050_RA_Y_FINE_GAIN 0x04 //[7:0] Y_FINE_GAIN
+#define MPU6050_RA_Z_FINE_GAIN 0x05 //[7:0] Z_FINE_GAIN
+#define MPU6050_RA_XA_OFFS_H 0x06 //[15:0] XA_OFFS
+#define MPU6050_RA_XA_OFFS_L_TC 0x07
+#define MPU6050_RA_YA_OFFS_H 0x08 //[15:0] YA_OFFS
+#define MPU6050_RA_YA_OFFS_L_TC 0x09
+#define MPU6050_RA_ZA_OFFS_H 0x0A //[15:0] ZA_OFFS
+#define MPU6050_RA_ZA_OFFS_L_TC 0x0B
+#define MPU6050_RA_XG_OFFS_USRH 0x13 //[15:0] XG_OFFS_USR
+#define MPU6050_RA_XG_OFFS_USRL 0x14
+#define MPU6050_RA_YG_OFFS_USRH 0x15 //[15:0] YG_OFFS_USR
+#define MPU6050_RA_YG_OFFS_USRL 0x16
+#define MPU6050_RA_ZG_OFFS_USRH 0x17 //[15:0] ZG_OFFS_USR
+#define MPU6050_RA_ZG_OFFS_USRL 0x18
+#define MPU6050_RA_SMPLRT_DIV 0x19
+#define MPU6050_RA_CONFIG 0x1A
+#define MPU6050_RA_GYRO_CONFIG 0x1B
+#define MPU6050_RA_ACCEL_CONFIG 0x1C
+#define MPU6050_RA_FF_THR 0x1D
+#define MPU6050_RA_FF_DUR 0x1E
+#define MPU6050_RA_MOT_THR 0x1F
+#define MPU6050_RA_MOT_DUR 0x20
+#define MPU6050_RA_ZRMOT_THR 0x21
+#define MPU6050_RA_ZRMOT_DUR 0x22
+#define MPU6050_RA_FIFO_EN 0x23
+#define MPU6050_RA_I2C_MST_CTRL 0x24
+#define MPU6050_RA_I2C_SLV0_ADDR 0x25
+#define MPU6050_RA_I2C_SLV0_REG 0x26
+#define MPU6050_RA_I2C_SLV0_CTRL 0x27
+#define MPU6050_RA_I2C_SLV1_ADDR 0x28
+#define MPU6050_RA_I2C_SLV1_REG 0x29
+#define MPU6050_RA_I2C_SLV1_CTRL 0x2A
+#define MPU6050_RA_I2C_SLV2_ADDR 0x2B
+#define MPU6050_RA_I2C_SLV2_REG 0x2C
+#define MPU6050_RA_I2C_SLV2_CTRL 0x2D
+#define MPU6050_RA_I2C_SLV3_ADDR 0x2E
+#define MPU6050_RA_I2C_SLV3_REG 0x2F
+#define MPU6050_RA_I2C_SLV3_CTRL 0x30
+#define MPU6050_RA_I2C_SLV4_ADDR 0x31
+#define MPU6050_RA_I2C_SLV4_REG 0x32
+#define MPU6050_RA_I2C_SLV4_DO 0x33
+#define MPU6050_RA_I2C_SLV4_CTRL 0x34
+#define MPU6050_RA_I2C_SLV4_DI 0x35
+#define MPU6050_RA_I2C_MST_STATUS 0x36
+#define MPU6050_RA_INT_PIN_CFG 0x37
+#define MPU6050_RA_INT_ENABLE 0x38
+#define MPU6050_RA_DMP_INT_STATUS 0x39
+#define MPU6050_RA_INT_STATUS 0x3A
+#define MPU6050_RA_ACCEL_XOUT_H 0x3B
+#define MPU6050_RA_ACCEL_XOUT_L 0x3C
+#define MPU6050_RA_ACCEL_YOUT_H 0x3D
+#define MPU6050_RA_ACCEL_YOUT_L 0x3E
+#define MPU6050_RA_ACCEL_ZOUT_H 0x3F
+#define MPU6050_RA_ACCEL_ZOUT_L 0x40
+#define MPU6050_RA_TEMP_OUT_H 0x41
+#define MPU6050_RA_TEMP_OUT_L 0x42
+#define MPU6050_RA_GYRO_XOUT_H 0x43
+#define MPU6050_RA_GYRO_XOUT_L 0x44
+#define MPU6050_RA_GYRO_YOUT_H 0x45
+#define MPU6050_RA_GYRO_YOUT_L 0x46
+#define MPU6050_RA_GYRO_ZOUT_H 0x47
+#define MPU6050_RA_GYRO_ZOUT_L 0x48
+#define MPU6050_RA_EXT_SENS_DATA_00 0x49
+#define MPU6050_RA_EXT_SENS_DATA_01 0x4A
+#define MPU6050_RA_EXT_SENS_DATA_02 0x4B
+#define MPU6050_RA_EXT_SENS_DATA_03 0x4C
+#define MPU6050_RA_EXT_SENS_DATA_04 0x4D
+#define MPU6050_RA_EXT_SENS_DATA_05 0x4E
+#define MPU6050_RA_EXT_SENS_DATA_06 0x4F
+#define MPU6050_RA_EXT_SENS_DATA_07 0x50
+#define MPU6050_RA_EXT_SENS_DATA_08 0x51
+#define MPU6050_RA_EXT_SENS_DATA_09 0x52
+#define MPU6050_RA_EXT_SENS_DATA_10 0x53
+#define MPU6050_RA_EXT_SENS_DATA_11 0x54
+#define MPU6050_RA_EXT_SENS_DATA_12 0x55
+#define MPU6050_RA_EXT_SENS_DATA_13 0x56
+#define MPU6050_RA_EXT_SENS_DATA_14 0x57
+#define MPU6050_RA_EXT_SENS_DATA_15 0x58
+#define MPU6050_RA_EXT_SENS_DATA_16 0x59
+#define MPU6050_RA_EXT_SENS_DATA_17 0x5A
+#define MPU6050_RA_EXT_SENS_DATA_18 0x5B
+#define MPU6050_RA_EXT_SENS_DATA_19 0x5C
+#define MPU6050_RA_EXT_SENS_DATA_20 0x5D
+#define MPU6050_RA_EXT_SENS_DATA_21 0x5E
+#define MPU6050_RA_EXT_SENS_DATA_22 0x5F
+#define MPU6050_RA_EXT_SENS_DATA_23 0x60
+#define MPU6050_RA_MOT_DETECT_STATUS 0x61
+#define MPU6050_RA_I2C_SLV0_DO 0x63
+#define MPU6050_RA_I2C_SLV1_DO 0x64
+#define MPU6050_RA_I2C_SLV2_DO 0x65
+#define MPU6050_RA_I2C_SLV3_DO 0x66
+#define MPU6050_RA_I2C_MST_DELAY_CTRL 0x67
+#define MPU6050_RA_SIGNAL_PATH_RESET 0x68
+#define MPU6050_RA_MOT_DETECT_CTRL 0x69
+#define MPU6050_RA_USER_CTRL 0x6A
+#define MPU6050_RA_PWR_MGMT_1 0x6B
+#define MPU6050_RA_PWR_MGMT_2 0x6C
+#define MPU6050_RA_BANK_SEL 0x6D
+#define MPU6050_RA_MEM_START_ADDR 0x6E
+#define MPU6050_RA_MEM_R_W 0x6F
+#define MPU6050_RA_DMP_CFG_1 0x70
+#define MPU6050_RA_DMP_CFG_2 0x71
+#define MPU6050_RA_FIFO_COUNTH 0x72
+#define MPU6050_RA_FIFO_COUNTL 0x73
+#define MPU6050_RA_FIFO_R_W 0x74
+#define MPU6050_RA_WHO_AM_I 0x75
+
+#define MPU6050_TC_PWR_MODE_BIT 7
+#define MPU6050_TC_OFFSET_BIT 6
+#define MPU6050_TC_OFFSET_LENGTH 6
+#define MPU6050_TC_OTP_BNK_VLD_BIT 0
+
+#define MPU6050_VDDIO_LEVEL_VLOGIC 0
+#define MPU6050_VDDIO_LEVEL_VDD 1
+
+#define MPU6050_CFG_EXT_SYNC_SET_BIT 5
+#define MPU6050_CFG_EXT_SYNC_SET_LENGTH 3
+#define MPU6050_CFG_DLPF_CFG_BIT 2
+#define MPU6050_CFG_DLPF_CFG_LENGTH 3
+
+#define MPU6050_EXT_SYNC_DISABLED 0x0
+#define MPU6050_EXT_SYNC_TEMP_OUT_L 0x1
+#define MPU6050_EXT_SYNC_GYRO_XOUT_L 0x2
+#define MPU6050_EXT_SYNC_GYRO_YOUT_L 0x3
+#define MPU6050_EXT_SYNC_GYRO_ZOUT_L 0x4
+#define MPU6050_EXT_SYNC_ACCEL_XOUT_L 0x5
+#define MPU6050_EXT_SYNC_ACCEL_YOUT_L 0x6
+#define MPU6050_EXT_SYNC_ACCEL_ZOUT_L 0x7
+
+#define MPU6050_DLPF_BW_256 0x00
+#define MPU6050_DLPF_BW_188 0x01
+#define MPU6050_DLPF_BW_98 0x02
+#define MPU6050_DLPF_BW_42 0x03
+#define MPU6050_DLPF_BW_20 0x04
+#define MPU6050_DLPF_BW_10 0x05
+#define MPU6050_DLPF_BW_5 0x06
+
+#define MPU6050_GCONFIG_FS_SEL_BIT 4
+#define MPU6050_GCONFIG_FS_SEL_LENGTH 2
+
+#define MPU6050_GYRO_FS_250 0x00
+#define MPU6050_GYRO_FS_500 0x01
+#define MPU6050_GYRO_FS_1000 0x02
+#define MPU6050_GYRO_FS_2000 0x03
+
+#define MPU6050_ACONFIG_XA_ST_BIT 7
+#define MPU6050_ACONFIG_YA_ST_BIT 6
+#define MPU6050_ACONFIG_ZA_ST_BIT 5
+#define MPU6050_ACONFIG_AFS_SEL_BIT 4
+#define MPU6050_ACONFIG_AFS_SEL_LENGTH 2
+#define MPU6050_ACONFIG_ACCEL_HPF_BIT 2
+#define MPU6050_ACONFIG_ACCEL_HPF_LENGTH 3
+
+#define MPU6050_ACCEL_FS_2 0x00
+#define MPU6050_ACCEL_FS_4 0x01
+#define MPU6050_ACCEL_FS_8 0x02
+#define MPU6050_ACCEL_FS_16 0x03
+
+#define MPU6050_DHPF_RESET 0x00
+#define MPU6050_DHPF_5 0x01
+#define MPU6050_DHPF_2P5 0x02
+#define MPU6050_DHPF_1P25 0x03
+#define MPU6050_DHPF_0P63 0x04
+#define MPU6050_DHPF_HOLD 0x07
+
+#define MPU6050_TEMP_FIFO_EN_BIT 7
+#define MPU6050_XG_FIFO_EN_BIT 6
+#define MPU6050_YG_FIFO_EN_BIT 5
+#define MPU6050_ZG_FIFO_EN_BIT 4
+#define MPU6050_ACCEL_FIFO_EN_BIT 3
+#define MPU6050_SLV2_FIFO_EN_BIT 2
+#define MPU6050_SLV1_FIFO_EN_BIT 1
+#define MPU6050_SLV0_FIFO_EN_BIT 0
+
+#define MPU6050_MULT_MST_EN_BIT 7
+#define MPU6050_WAIT_FOR_ES_BIT 6
+#define MPU6050_SLV_3_FIFO_EN_BIT 5
+#define MPU6050_I2C_MST_P_NSR_BIT 4
+#define MPU6050_I2C_MST_CLK_BIT 3
+#define MPU6050_I2C_MST_CLK_LENGTH 4
+
+#define MPU6050_CLOCK_DIV_348 0x0
+#define MPU6050_CLOCK_DIV_333 0x1
+#define MPU6050_CLOCK_DIV_320 0x2
+#define MPU6050_CLOCK_DIV_308 0x3
+#define MPU6050_CLOCK_DIV_296 0x4
+#define MPU6050_CLOCK_DIV_286 0x5
+#define MPU6050_CLOCK_DIV_276 0x6
+#define MPU6050_CLOCK_DIV_267 0x7
+#define MPU6050_CLOCK_DIV_258 0x8
+#define MPU6050_CLOCK_DIV_500 0x9
+#define MPU6050_CLOCK_DIV_471 0xA
+#define MPU6050_CLOCK_DIV_444 0xB
+#define MPU6050_CLOCK_DIV_421 0xC
+#define MPU6050_CLOCK_DIV_400 0xD
+#define MPU6050_CLOCK_DIV_381 0xE
+#define MPU6050_CLOCK_DIV_364 0xF
+
+#define MPU6050_I2C_SLV_RW_BIT 7
+#define MPU6050_I2C_SLV_ADDR_BIT 6
+#define MPU6050_I2C_SLV_ADDR_LENGTH 7
+#define MPU6050_I2C_SLV_EN_BIT 7
+#define MPU6050_I2C_SLV_BYTE_SW_BIT 6
+#define MPU6050_I2C_SLV_REG_DIS_BIT 5
+#define MPU6050_I2C_SLV_GRP_BIT 4
+#define MPU6050_I2C_SLV_LEN_BIT 3
+#define MPU6050_I2C_SLV_LEN_LENGTH 4
+
+#define MPU6050_I2C_SLV4_RW_BIT 7
+#define MPU6050_I2C_SLV4_ADDR_BIT 6
+#define MPU6050_I2C_SLV4_ADDR_LENGTH 7
+#define MPU6050_I2C_SLV4_EN_BIT 7
+#define MPU6050_I2C_SLV4_INT_EN_BIT 6
+#define MPU6050_I2C_SLV4_REG_DIS_BIT 5
+#define MPU6050_I2C_SLV4_MST_DLY_BIT 4
+#define MPU6050_I2C_SLV4_MST_DLY_LENGTH 5
+
+#define MPU6050_MST_PASS_THROUGH_BIT 7
+#define MPU6050_MST_I2C_SLV4_DONE_BIT 6
+#define MPU6050_MST_I2C_LOST_ARB_BIT 5
+#define MPU6050_MST_I2C_SLV4_NACK_BIT 4
+#define MPU6050_MST_I2C_SLV3_NACK_BIT 3
+#define MPU6050_MST_I2C_SLV2_NACK_BIT 2
+#define MPU6050_MST_I2C_SLV1_NACK_BIT 1
+#define MPU6050_MST_I2C_SLV0_NACK_BIT 0
+
+#define MPU6050_INTCFG_INT_LEVEL_BIT 7
+#define MPU6050_INTCFG_INT_OPEN_BIT 6
+#define MPU6050_INTCFG_LATCH_INT_EN_BIT 5
+#define MPU6050_INTCFG_INT_RD_CLEAR_BIT 4
+#define MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT 3
+#define MPU6050_INTCFG_FSYNC_INT_EN_BIT 2
+#define MPU6050_INTCFG_I2C_BYPASS_EN_BIT 1
+#define MPU6050_INTCFG_CLKOUT_EN_BIT 0
+
+#define MPU6050_INTMODE_ACTIVEHIGH 0x00
+#define MPU6050_INTMODE_ACTIVELOW 0x01
+
+#define MPU6050_INTDRV_PUSHPULL 0x00
+#define MPU6050_INTDRV_OPENDRAIN 0x01
+
+#define MPU6050_INTLATCH_50USPULSE 0x00
+#define MPU6050_INTLATCH_WAITCLEAR 0x01
+
+#define MPU6050_INTCLEAR_STATUSREAD 0x00
+#define MPU6050_INTCLEAR_ANYREAD 0x01
+
+#define MPU6050_INTERRUPT_FF_BIT 7
+#define MPU6050_INTERRUPT_MOT_BIT 6
+#define MPU6050_INTERRUPT_ZMOT_BIT 5
+#define MPU6050_INTERRUPT_FIFO_OFLOW_BIT 4
+#define MPU6050_INTERRUPT_I2C_MST_INT_BIT 3
+#define MPU6050_INTERRUPT_PLL_RDY_INT_BIT 2
+#define MPU6050_INTERRUPT_DMP_INT_BIT 1
+#define MPU6050_INTERRUPT_DATA_RDY_BIT 0
+
+// TODO: figure out what these actually do
+// UMPL source code is not very obivous
+#define MPU6050_DMPINT_5_BIT 5
+#define MPU6050_DMPINT_4_BIT 4
+#define MPU6050_DMPINT_3_BIT 3
+#define MPU6050_DMPINT_2_BIT 2
+#define MPU6050_DMPINT_1_BIT 1
+#define MPU6050_DMPINT_0_BIT 0
+
+#define MPU6050_MOTION_MOT_XNEG_BIT 7
+#define MPU6050_MOTION_MOT_XPOS_BIT 6
+#define MPU6050_MOTION_MOT_YNEG_BIT 5
+#define MPU6050_MOTION_MOT_YPOS_BIT 4
+#define MPU6050_MOTION_MOT_ZNEG_BIT 3
+#define MPU6050_MOTION_MOT_ZPOS_BIT 2
+#define MPU6050_MOTION_MOT_ZRMOT_BIT 0
+
+#define MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT 7
+#define MPU6050_DELAYCTRL_I2C_SLV4_DLY_EN_BIT 4
+#define MPU6050_DELAYCTRL_I2C_SLV3_DLY_EN_BIT 3
+#define MPU6050_DELAYCTRL_I2C_SLV2_DLY_EN_BIT 2
+#define MPU6050_DELAYCTRL_I2C_SLV1_DLY_EN_BIT 1
+#define MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT 0
+
+#define MPU6050_PATHRESET_GYRO_RESET_BIT 2
+#define MPU6050_PATHRESET_ACCEL_RESET_BIT 1
+#define MPU6050_PATHRESET_TEMP_RESET_BIT 0
+
+#define MPU6050_DETECT_ACCEL_ON_DELAY_BIT 5
+#define MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH 2
+#define MPU6050_DETECT_FF_COUNT_BIT 3
+#define MPU6050_DETECT_FF_COUNT_LENGTH 2
+#define MPU6050_DETECT_MOT_COUNT_BIT 1
+#define MPU6050_DETECT_MOT_COUNT_LENGTH 2
+
+#define MPU6050_DETECT_DECREMENT_RESET 0x0
+#define MPU6050_DETECT_DECREMENT_1 0x1
+#define MPU6050_DETECT_DECREMENT_2 0x2
+#define MPU6050_DETECT_DECREMENT_4 0x3
+
+#define MPU6050_USERCTRL_DMP_EN_BIT 7
+#define MPU6050_USERCTRL_FIFO_EN_BIT 6
+#define MPU6050_USERCTRL_I2C_MST_EN_BIT 5
+#define MPU6050_USERCTRL_I2C_IF_DIS_BIT 4
+#define MPU6050_USERCTRL_DMP_RESET_BIT 3
+#define MPU6050_USERCTRL_FIFO_RESET_BIT 2
+#define MPU6050_USERCTRL_I2C_MST_RESET_BIT 1
+#define MPU6050_USERCTRL_SIG_COND_RESET_BIT 0
+
+#define MPU6050_PWR1_DEVICE_RESET_BIT 7
+#define MPU6050_PWR1_SLEEP_BIT 6
+#define MPU6050_PWR1_CYCLE_BIT 5
+#define MPU6050_PWR1_TEMP_DIS_BIT 3
+#define MPU6050_PWR1_CLKSEL_BIT 2
+#define MPU6050_PWR1_CLKSEL_LENGTH 3
+
+#define MPU6050_CLOCK_INTERNAL 0x00
+#define MPU6050_CLOCK_PLL_XGYRO 0x01
+#define MPU6050_CLOCK_PLL_YGYRO 0x02
+#define MPU6050_CLOCK_PLL_ZGYRO 0x03
+#define MPU6050_CLOCK_PLL_EXT32K 0x04
+#define MPU6050_CLOCK_PLL_EXT19M 0x05
+#define MPU6050_CLOCK_KEEP_RESET 0x07
+
+#define MPU6050_PWR2_LP_WAKE_CTRL_BIT 7
+#define MPU6050_PWR2_LP_WAKE_CTRL_LENGTH 2
+#define MPU6050_PWR2_STBY_XA_BIT 5
+#define MPU6050_PWR2_STBY_YA_BIT 4
+#define MPU6050_PWR2_STBY_ZA_BIT 3
+#define MPU6050_PWR2_STBY_XG_BIT 2
+#define MPU6050_PWR2_STBY_YG_BIT 1
+#define MPU6050_PWR2_STBY_ZG_BIT 0
+
+#define MPU6050_WAKE_FREQ_1P25 0x0
+#define MPU6050_WAKE_FREQ_2P5 0x1
+#define MPU6050_WAKE_FREQ_5 0x2
+#define MPU6050_WAKE_FREQ_10 0x3
+
+#define MPU6050_BANKSEL_PRFTCH_EN_BIT 6
+#define MPU6050_BANKSEL_CFG_USER_BANK_BIT 5
+#define MPU6050_BANKSEL_MEM_SEL_BIT 4
+#define MPU6050_BANKSEL_MEM_SEL_LENGTH 5
+
+#define MPU6050_WHO_AM_I_BIT 6
+#define MPU6050_WHO_AM_I_LENGTH 6
+
+#define MPU6050_DMP_MEMORY_BANKS 8
+#define MPU6050_DMP_MEMORY_BANK_SIZE 256
+#define MPU6050_DMP_MEMORY_CHUNK_SIZE 16
+
+// note: DMP code memory blocks defined at end of header file
+
+class MPU6050 {
+ private:
+ I2Cdev i2Cdev;
+ Serial debugSerial;
+ public:
+ MPU6050();
+ MPU6050(uint8_t address);
+
+ void initialize();
+ bool testConnection();
+
+ // AUX_VDDIO register
+ uint8_t getAuxVDDIOLevel();
+ void setAuxVDDIOLevel(uint8_t level);
+
+ // SMPLRT_DIV register
+ uint8_t getRate();
+ void setRate(uint8_t rate);
+
+
+ // CONFIG register
+ uint8_t getExternalFrameSync();
+ void setExternalFrameSync(uint8_t sync);
+ uint8_t getDLPFMode();
+ void setDLPFMode(uint8_t bandwidth);
+
+ // GYRO_CONFIG register
+ uint8_t getFullScaleGyroRange();
+ void setFullScaleGyroRange(uint8_t range);
+
+ // ACCEL_CONFIG register
+ bool getAccelXSelfTest();
+ void setAccelXSelfTest(bool enabled);
+ bool getAccelYSelfTest();
+ void setAccelYSelfTest(bool enabled);
+ bool getAccelZSelfTest();
+ void setAccelZSelfTest(bool enabled);
+ uint8_t getFullScaleAccelRange();
+ void setFullScaleAccelRange(uint8_t range);
+ uint8_t getDHPFMode();
+ void setDHPFMode(uint8_t mode);
+
+ // FF_THR register
+ uint8_t getFreefallDetectionThreshold();
+ void setFreefallDetectionThreshold(uint8_t threshold);
+
+ // FF_DUR register
+ uint8_t getFreefallDetectionDuration();
+ void setFreefallDetectionDuration(uint8_t duration);
+
+ // MOT_THR register
+ uint8_t getMotionDetectionThreshold();
+ void setMotionDetectionThreshold(uint8_t threshold);
+
+ // MOT_DUR register
+ uint8_t getMotionDetectionDuration();
+ void setMotionDetectionDuration(uint8_t duration);
+
+ // ZRMOT_THR register
+ uint8_t getZeroMotionDetectionThreshold();
+ void setZeroMotionDetectionThreshold(uint8_t threshold);
+
+ // ZRMOT_DUR register
+ uint8_t getZeroMotionDetectionDuration();
+ void setZeroMotionDetectionDuration(uint8_t duration);
+
+ // FIFO_EN register
+ bool getTempFIFOEnabled();
+ void setTempFIFOEnabled(bool enabled);
+ bool getXGyroFIFOEnabled();
+ void setXGyroFIFOEnabled(bool enabled);
+ bool getYGyroFIFOEnabled();
+ void setYGyroFIFOEnabled(bool enabled);
+ bool getZGyroFIFOEnabled();
+ void setZGyroFIFOEnabled(bool enabled);
+ bool getAccelFIFOEnabled();
+ void setAccelFIFOEnabled(bool enabled);
+ bool getSlave2FIFOEnabled();
+ void setSlave2FIFOEnabled(bool enabled);
+ bool getSlave1FIFOEnabled();
+ void setSlave1FIFOEnabled(bool enabled);
+ bool getSlave0FIFOEnabled();
+ void setSlave0FIFOEnabled(bool enabled);
+
+ // I2C_MST_CTRL register
+ bool getMultiMasterEnabled();
+ void setMultiMasterEnabled(bool enabled);
+ bool getWaitForExternalSensorEnabled();
+ void setWaitForExternalSensorEnabled(bool enabled);
+ bool getSlave3FIFOEnabled();
+ void setSlave3FIFOEnabled(bool enabled);
+ bool getSlaveReadWriteTransitionEnabled();
+ void setSlaveReadWriteTransitionEnabled(bool enabled);
+ uint8_t getMasterClockSpeed();
+ void setMasterClockSpeed(uint8_t speed);
+
+ // I2C_SLV* registers (Slave 0-3)
+ uint8_t getSlaveAddress(uint8_t num);
+ void setSlaveAddress(uint8_t num, uint8_t address);
+ uint8_t getSlaveRegister(uint8_t num);
+ void setSlaveRegister(uint8_t num, uint8_t reg);
+ bool getSlaveEnabled(uint8_t num);
+ void setSlaveEnabled(uint8_t num, bool enabled);
+ bool getSlaveWordByteSwap(uint8_t num);
+ void setSlaveWordByteSwap(uint8_t num, bool enabled);
+ bool getSlaveWriteMode(uint8_t num);
+ void setSlaveWriteMode(uint8_t num, bool mode);
+ bool getSlaveWordGroupOffset(uint8_t num);
+ void setSlaveWordGroupOffset(uint8_t num, bool enabled);
+ uint8_t getSlaveDataLength(uint8_t num);
+ void setSlaveDataLength(uint8_t num, uint8_t length);
+
+ // I2C_SLV* registers (Slave 4)
+ uint8_t getSlave4Address();
+ void setSlave4Address(uint8_t address);
+ uint8_t getSlave4Register();
+ void setSlave4Register(uint8_t reg);
+ void setSlave4OutputByte(uint8_t data);
+ bool getSlave4Enabled();
+ void setSlave4Enabled(bool enabled);
+ bool getSlave4InterruptEnabled();
+ void setSlave4InterruptEnabled(bool enabled);
+ bool getSlave4WriteMode();
+ void setSlave4WriteMode(bool mode);
+ uint8_t getSlave4MasterDelay();
+ void setSlave4MasterDelay(uint8_t delay);
+ uint8_t getSlate4InputByte();
+
+ // I2C_MST_STATUS register
+ bool getPassthroughStatus();
+ bool getSlave4IsDone();
+ bool getLostArbitration();
+ bool getSlave4Nack();
+ bool getSlave3Nack();
+ bool getSlave2Nack();
+ bool getSlave1Nack();
+ bool getSlave0Nack();
+
+ // INT_PIN_CFG register
+ bool getInterruptMode();
+ void setInterruptMode(bool mode);
+ bool getInterruptDrive();
+ void setInterruptDrive(bool drive);
+ bool getInterruptLatch();
+ void setInterruptLatch(bool latch);
+ bool getInterruptLatchClear();
+ void setInterruptLatchClear(bool clear);
+ bool getFSyncInterruptLevel();
+ void setFSyncInterruptLevel(bool level);
+ bool getFSyncInterruptEnabled();
+ void setFSyncInterruptEnabled(bool enabled);
+ bool getI2CBypassEnabled();
+ void setI2CBypassEnabled(bool enabled);
+ bool getClockOutputEnabled();
+ void setClockOutputEnabled(bool enabled);
+
+ // INT_ENABLE register
+ uint8_t getIntEnabled();
+ void setIntEnabled(uint8_t enabled);
+ bool getIntFreefallEnabled();
+ void setIntFreefallEnabled(bool enabled);
+ bool getIntMotionEnabled();
+ void setIntMotionEnabled(bool enabled);
+ bool getIntZeroMotionEnabled();
+ void setIntZeroMotionEnabled(bool enabled);
+ bool getIntFIFOBufferOverflowEnabled();
+ void setIntFIFOBufferOverflowEnabled(bool enabled);
+ bool getIntI2CMasterEnabled();
+ void setIntI2CMasterEnabled(bool enabled);
+ bool getIntDataReadyEnabled();
+ void setIntDataReadyEnabled(bool enabled);
+
+ // INT_STATUS register
+ uint8_t getIntStatus();
+ bool getIntFreefallStatus();
+ bool getIntMotionStatus();
+ bool getIntZeroMotionStatus();
+ bool getIntFIFOBufferOverflowStatus();
+ bool getIntI2CMasterStatus();
+ bool getIntDataReadyStatus();
+
+ // ACCEL_*OUT_* registers
+ void getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz);
+ void getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz);
+ void getAcceleration(int16_t* x, int16_t* y, int16_t* z);
+ int16_t getAccelerationX();
+ int16_t getAccelerationY();
+ int16_t getAccelerationZ();
+
+ // TEMP_OUT_* registers
+ int16_t getTemperature();
+
+ // GYRO_*OUT_* registers
+ void getRotation(int16_t* x, int16_t* y, int16_t* z);
+ int16_t getRotationX();
+ int16_t getRotationY();
+ int16_t getRotationZ();
+
+ // EXT_SENS_DATA_* registers
+ uint8_t getExternalSensorByte(int position);
+ uint16_t getExternalSensorWord(int position);
+ uint32_t getExternalSensorDWord(int position);
+
+ // MOT_DETECT_STATUS register
+ bool getXNegMotionDetected();
+ bool getXPosMotionDetected();
+ bool getYNegMotionDetected();
+ bool getYPosMotionDetected();
+ bool getZNegMotionDetected();
+ bool getZPosMotionDetected();
+ bool getZeroMotionDetected();
+
+ // I2C_SLV*_DO register
+ void setSlaveOutputByte(uint8_t num, uint8_t data);
+
+ // I2C_MST_DELAY_CTRL register
+ bool getExternalShadowDelayEnabled();
+ void setExternalShadowDelayEnabled(bool enabled);
+ bool getSlaveDelayEnabled(uint8_t num);
+ void setSlaveDelayEnabled(uint8_t num, bool enabled);
+
+ // SIGNAL_PATH_RESET register
+ void resetGyroscopePath();
+ void resetAccelerometerPath();
+ void resetTemperaturePath();
+
+ // MOT_DETECT_CTRL register
+ uint8_t getAccelerometerPowerOnDelay();
+ void setAccelerometerPowerOnDelay(uint8_t delay);
+ uint8_t getFreefallDetectionCounterDecrement();
+ void setFreefallDetectionCounterDecrement(uint8_t decrement);
+ uint8_t getMotionDetectionCounterDecrement();
+ void setMotionDetectionCounterDecrement(uint8_t decrement);
+
+ // USER_CTRL register
+ bool getFIFOEnabled();
+ void setFIFOEnabled(bool enabled);
+ bool getI2CMasterModeEnabled();
+ void setI2CMasterModeEnabled(bool enabled);
+ void switchSPIEnabled(bool enabled);
+ void resetFIFO();
+ void resetI2CMaster();
+ void resetSensors();
+
+ // PWR_MGMT_1 register
+ void reset();
+ bool getSleepEnabled();
+ void setSleepEnabled(bool enabled);
+ bool getWakeCycleEnabled();
+ void setWakeCycleEnabled(bool enabled);
+ bool getTempSensorEnabled();
+ void setTempSensorEnabled(bool enabled);
+ uint8_t getClockSource();
+ void setClockSource(uint8_t source);
+
+ // PWR_MGMT_2 register
+ uint8_t getWakeFrequency();
+ void setWakeFrequency(uint8_t frequency);
+ bool getStandbyXAccelEnabled();
+ void setStandbyXAccelEnabled(bool enabled);
+ bool getStandbyYAccelEnabled();
+ void setStandbyYAccelEnabled(bool enabled);
+ bool getStandbyZAccelEnabled();
+ void setStandbyZAccelEnabled(bool enabled);
+ bool getStandbyXGyroEnabled();
+ void setStandbyXGyroEnabled(bool enabled);
+ bool getStandbyYGyroEnabled();
+ void setStandbyYGyroEnabled(bool enabled);
+ bool getStandbyZGyroEnabled();
+ void setStandbyZGyroEnabled(bool enabled);
+
+ // FIFO_COUNT_* registers
+ uint16_t getFIFOCount();
+
+ // FIFO_R_W register
+ uint8_t getFIFOByte();
+ void setFIFOByte(uint8_t data);
+ void getFIFOBytes(uint8_t *data, uint8_t length);
+
+ // WHO_AM_I register
+ uint8_t getDeviceID();
+ void setDeviceID(uint8_t id);
+
+ // ======== UNDOCUMENTED/DMP REGISTERS/METHODS ========
+
+ // XG_OFFS_TC register
+ uint8_t getOTPBankValid();
+ void setOTPBankValid(bool enabled);
+ int8_t getXGyroOffset();
+ void setXGyroOffset(int8_t offset);
+
+ // YG_OFFS_TC register
+ int8_t getYGyroOffset();
+ void setYGyroOffset(int8_t offset);
+
+ // ZG_OFFS_TC register
+ int8_t getZGyroOffset();
+ void setZGyroOffset(int8_t offset);
+
+ // X_FINE_GAIN register
+ int8_t getXFineGain();
+ void setXFineGain(int8_t gain);
+
+ // Y_FINE_GAIN register
+ int8_t getYFineGain();
+ void setYFineGain(int8_t gain);
+
+ // Z_FINE_GAIN register
+ int8_t getZFineGain();
+ void setZFineGain(int8_t gain);
+
+ // XA_OFFS_* registers
+ int16_t getXAccelOffset();
+ void setXAccelOffset(int16_t offset);
+
+ // YA_OFFS_* register
+ int16_t getYAccelOffset();
+ void setYAccelOffset(int16_t offset);
+
+ // ZA_OFFS_* register
+ int16_t getZAccelOffset();
+ void setZAccelOffset(int16_t offset);
+
+ // XG_OFFS_USR* registers
+ int16_t getXGyroOffsetUser();
+ void setXGyroOffsetUser(int16_t offset);
+
+ // YG_OFFS_USR* register
+ int16_t getYGyroOffsetUser();
+ void setYGyroOffsetUser(int16_t offset);
+
+ // ZG_OFFS_USR* register
+ int16_t getZGyroOffsetUser();
+ void setZGyroOffsetUser(int16_t offset);
+
+ // INT_ENABLE register (DMP functions)
+ bool getIntPLLReadyEnabled();
+ void setIntPLLReadyEnabled(bool enabled);
+ bool getIntDMPEnabled();
+ void setIntDMPEnabled(bool enabled);
+
+ // DMP_INT_STATUS
+ bool getDMPInt5Status();
+ bool getDMPInt4Status();
+ bool getDMPInt3Status();
+ bool getDMPInt2Status();
+ bool getDMPInt1Status();
+ bool getDMPInt0Status();
+
+ // INT_STATUS register (DMP functions)
+ bool getIntPLLReadyStatus();
+ bool getIntDMPStatus();
+
+ // USER_CTRL register (DMP functions)
+ bool getDMPEnabled();
+ void setDMPEnabled(bool enabled);
+ void resetDMP();
+
+ // BANK_SEL register
+ void setMemoryBank(uint8_t bank, bool prefetchEnabled=false, bool userBank=false);
+
+ // MEM_START_ADDR register
+ void setMemoryStartAddress(uint8_t address);
+
+ // MEM_R_W register
+ uint8_t readMemoryByte();
+ void writeMemoryByte(uint8_t data);
+ void readMemoryBlock(uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0);
+ bool writeMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0, bool verify=true, bool useProgMem=false);
+ bool writeProgMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0, bool verify=true);
+
+ bool writeDMPConfigurationSet(const uint8_t *data, uint16_t dataSize, bool useProgMem=false);
+ bool writeProgDMPConfigurationSet(const uint8_t *data, uint16_t dataSize);
+
+ // DMP_CFG_1 register
+ uint8_t getDMPConfig1();
+ void setDMPConfig1(uint8_t config);
+
+ // DMP_CFG_2 register
+ uint8_t getDMPConfig2();
+ void setDMPConfig2(uint8_t config);
+
+ // special methods for MotionApps 2.0 implementation
+ #ifdef MPU6050_INCLUDE_DMP_MOTIONAPPS20
+ uint8_t *dmpPacketBuffer;
+ uint16_t dmpPacketSize;
+
+ uint8_t dmpInitialize();
+ bool dmpPacketAvailable();
+
+ uint8_t dmpSetFIFORate(uint8_t fifoRate);
+ uint8_t dmpGetFIFORate();
+ uint8_t dmpGetSampleStepSizeMS();
+ uint8_t dmpGetSampleFrequency();
+ int32_t dmpDecodeTemperature(int8_t tempReg);
+
+ // Register callbacks after a packet of FIFO data is processed
+ //uint8_t dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+ //uint8_t dmpUnregisterFIFORateProcess(inv_obj_func func);
+ uint8_t dmpRunFIFORateProcesses();
+
+ // Setup FIFO for various output
+ uint8_t dmpSendQuaternion(uint_fast16_t accuracy);
+ uint8_t dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendPacketNumber(uint_fast16_t accuracy);
+ uint8_t dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+ // Get Fixed Point data from FIFO
+ uint8_t dmpGetAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(Quaternion *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpSetLinearAccelFilterCoefficient(float coef);
+ uint8_t dmpGetLinearAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity);
+ uint8_t dmpGetLinearAccelInWorld(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q);
+ uint8_t dmpGetGyroAndAccelSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(VectorInt16 *g, VectorInt16 *a, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetControlData(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetTemperature(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorFloat *v, Quaternion *q);
+ uint8_t dmpGetUnquantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetExternalSensorData(int32_t *data, uint16_t size, const uint8_t* packet=0);
+ uint8_t dmpGetEIS(int32_t *data, const uint8_t* packet=0);
+
+ uint8_t dmpGetEuler(float *data, Quaternion *q);
+ uint8_t dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity);
+
+ // Get Floating Point data from FIFO
+ uint8_t dmpGetAccelFloat(float *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternionFloat(float *data, const uint8_t* packet=0);
+
+ uint8_t dmpProcessFIFOPacket(const unsigned char *dmpData);
+ uint8_t dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed=NULL);
+
+ uint8_t dmpSetFIFOProcessedCallback(void (*func) (void));
+
+ uint8_t dmpInitFIFOParam();
+ uint8_t dmpCloseFIFO();
+ uint8_t dmpSetGyroDataSource(uint8_t source);
+ uint8_t dmpDecodeQuantizedAccel();
+ uint32_t dmpGetGyroSumOfSquare();
+ uint32_t dmpGetAccelSumOfSquare();
+ void dmpOverrideQuaternion(long *q);
+ uint16_t dmpGetFIFOPacketSize();
+ #endif
+
+ // special methods for MotionApps 4.1 implementation
+ #ifdef MPU6050_INCLUDE_DMP_MOTIONAPPS41
+ uint8_t *dmpPacketBuffer;
+ uint16_t dmpPacketSize;
+
+ uint8_t dmpInitialize();
+ bool dmpPacketAvailable();
+
+ uint8_t dmpSetFIFORate(uint8_t fifoRate);
+ uint8_t dmpGetFIFORate();
+ uint8_t dmpGetSampleStepSizeMS();
+ uint8_t dmpGetSampleFrequency();
+ int32_t dmpDecodeTemperature(int8_t tempReg);
+
+ // Register callbacks after a packet of FIFO data is processed
+ //uint8_t dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+ //uint8_t dmpUnregisterFIFORateProcess(inv_obj_func func);
+ uint8_t dmpRunFIFORateProcesses();
+
+ // Setup FIFO for various output
+ uint8_t dmpSendQuaternion(uint_fast16_t accuracy);
+ uint8_t dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendPacketNumber(uint_fast16_t accuracy);
+ uint8_t dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+ // Get Fixed Point data from FIFO
+ uint8_t dmpGetAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(Quaternion *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetMag(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpSetLinearAccelFilterCoefficient(float coef);
+ uint8_t dmpGetLinearAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity);
+ uint8_t dmpGetLinearAccelInWorld(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q);
+ uint8_t dmpGetGyroAndAccelSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(VectorInt16 *g, VectorInt16 *a, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetControlData(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetTemperature(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorFloat *v, Quaternion *q);
+ uint8_t dmpGetUnquantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetExternalSensorData(int32_t *data, uint16_t size, const uint8_t* packet=0);
+ uint8_t dmpGetEIS(int32_t *data, const uint8_t* packet=0);
+
+ uint8_t dmpGetEuler(float *data, Quaternion *q);
+ uint8_t dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity);
+
+ // Get Floating Point data from FIFO
+ uint8_t dmpGetAccelFloat(float *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternionFloat(float *data, const uint8_t* packet=0);
+
+ uint8_t dmpProcessFIFOPacket(const unsigned char *dmpData);
+ uint8_t dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed=NULL);
+
+ uint8_t dmpSetFIFOProcessedCallback(void (*func) (void));
+
+ uint8_t dmpInitFIFOParam();
+ uint8_t dmpCloseFIFO();
+ uint8_t dmpSetGyroDataSource(uint8_t source);
+ uint8_t dmpDecodeQuantizedAccel();
+ uint32_t dmpGetGyroSumOfSquare();
+ uint32_t dmpGetAccelSumOfSquare();
+ void dmpOverrideQuaternion(long *q);
+ uint16_t dmpGetFIFOPacketSize();
+ #endif
+
+ private:
+ uint8_t devAddr;
+ uint8_t buffer[14];
+};
+
+#endif /* _MPU6050_H_ */
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/helper_3dmath.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,216 @@
+// I2C device class (I2Cdev) demonstration Arduino sketch for MPU6050 class, 3D math helper
+// 6/5/2012 by Jeff Rowberg <jeff@rowberg.net>
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// 2012-06-05 - add 3D math helper file to DMP6 example sketch
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _HELPER_3DMATH_H_
+#define _HELPER_3DMATH_H_
+
+class Quaternion {
+ public:
+ float w;
+ float x;
+ float y;
+ float z;
+
+ Quaternion() {
+ w = 1.0f;
+ x = 0.0f;
+ y = 0.0f;
+ z = 0.0f;
+ }
+
+ Quaternion(float nw, float nx, float ny, float nz) {
+ w = nw;
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ Quaternion getProduct(Quaternion q) {
+ // Quaternion multiplication is defined by:
+ // (Q1 * Q2).w = (w1w2 - x1x2 - y1y2 - z1z2)
+ // (Q1 * Q2).x = (w1x2 + x1w2 + y1z2 - z1y2)
+ // (Q1 * Q2).y = (w1y2 - x1z2 + y1w2 + z1x2)
+ // (Q1 * Q2).z = (w1z2 + x1y2 - y1x2 + z1w2
+ return Quaternion(
+ w*q.w - x*q.x - y*q.y - z*q.z, // new w
+ w*q.x + x*q.w + y*q.z - z*q.y, // new x
+ w*q.y - x*q.z + y*q.w + z*q.x, // new y
+ w*q.z + x*q.y - y*q.x + z*q.w); // new z
+ }
+
+ Quaternion getConjugate() {
+ return Quaternion(w, -x, -y, -z);
+ }
+
+ float getMagnitude() {
+ return sqrt(w*w + x*x + y*y + z*z);
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ w /= m;
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ Quaternion getNormalized() {
+ Quaternion r(w, x, y, z);
+ r.normalize();
+ return r;
+ }
+};
+
+class VectorInt16 {
+ public:
+ int16_t x;
+ int16_t y;
+ int16_t z;
+
+ VectorInt16() {
+ x = 0;
+ y = 0;
+ z = 0;
+ }
+
+ VectorInt16(int16_t nx, int16_t ny, int16_t nz) {
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ float getMagnitude() {
+ return sqrt((float)(x*x + y*y + z*z));
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ VectorInt16 getNormalized() {
+ VectorInt16 r(x, y, z);
+ r.normalize();
+ return r;
+ }
+
+ void rotate(Quaternion *q) {
+ // http://www.cprogramming.com/tutorial/3d/quaternions.html
+ // http://www.euclideanspace.com/maths/algebra/realNormedAlgebra/quaternions/transforms/index.htm
+ // http://content.gpwiki.org/index.php/OpenGL:Tutorials:Using_Quaternions_to_represent_rotation
+ // ^ or: http://webcache.googleusercontent.com/search?q=cache:xgJAp3bDNhQJ:content.gpwiki.org/index.php/OpenGL:Tutorials:Using_Quaternions_to_represent_rotation&hl=en&gl=us&strip=1
+
+ // P_out = q * P_in * conj(q)
+ // - P_out is the output vector
+ // - q is the orientation quaternion
+ // - P_in is the input vector (a*aReal)
+ // - conj(q) is the conjugate of the orientation quaternion (q=[w,x,y,z], q*=[w,-x,-y,-z])
+ Quaternion p(0, x, y, z);
+
+ // quaternion multiplication: q * p, stored back in p
+ p = q -> getProduct(p);
+
+ // quaternion multiplication: p * conj(q), stored back in p
+ p = p.getProduct(q -> getConjugate());
+
+ // p quaternion is now [0, x', y', z']
+ x = p.x;
+ y = p.y;
+ z = p.z;
+ }
+
+ VectorInt16 getRotated(Quaternion *q) {
+ VectorInt16 r(x, y, z);
+ r.rotate(q);
+ return r;
+ }
+};
+
+class VectorFloat {
+ public:
+ float x;
+ float y;
+ float z;
+
+ VectorFloat() {
+ x = 0;
+ y = 0;
+ z = 0;
+ }
+
+ VectorFloat(float nx, float ny, float nz) {
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ float getMagnitude() {
+ return sqrt(x*x + y*y + z*z);
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ VectorFloat getNormalized() {
+ VectorFloat r(x, y, z);
+ r.normalize();
+ return r;
+ }
+
+ void rotate(Quaternion *q) {
+ Quaternion p(0, x, y, z);
+
+ // quaternion multiplication: q * p, stored back in p
+ p = q -> getProduct(p);
+
+ // quaternion multiplication: p * conj(q), stored back in p
+ p = p.getProduct(q -> getConjugate());
+
+ // p quaternion is now [0, x', y', z']
+ x = p.x;
+ y = p.y;
+ z = p.z;
+ }
+
+ VectorFloat getRotated(Quaternion *q) {
+ VectorFloat r(x, y, z);
+ r.rotate(q);
+ return r;
+ }
+};
+
+#endif /* _HELPER_3DMATH_H_ */
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU6050/vector_math.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,1115 @@
+/*
+Copyright (c) 2007, Markus Trenkwalder
+
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice,
+ this list of conditions and the following disclaimer.
+
+* Redistributions in binary form must reproduce the above copyright notice,
+ this list of conditions and the following disclaimer in the documentation
+ and/or other materials provided with the distribution.
+
+* Neither the name of the library's copyright owner nor the names of its
+ contributors may be used to endorse or promote products derived from this
+ software without specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
+CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
+EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
+PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
+PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
+LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*/
+
+#ifndef VECTOR_MATH_H
+#define VECTOR_MATH_H
+
+//#include <cmath>
+
+// "minor" can be defined from GCC and can cause problems
+#undef minor
+
+#ifndef M_PI
+#define M_PI 3.14159265358979323846
+#endif
+
+namespace vmath {
+
+//using std::sin;
+//using std::cos;
+//using std::acos;
+//using std::sqrt;
+
+template <typename T>
+inline T rsqrt(T x)
+{
+ return T(1) / sqrt(x);
+}
+
+template <typename T>
+inline T inv(T x)
+{
+ return T(1) / x;
+}
+
+namespace detail {
+ // This function is used heavily in this library. Here is a generic
+ // implementation for it. If you can provide a faster one for your specific
+ // types this can speed up things considerably.
+ template <typename T>
+ inline T multiply_accumulate(int count, const T *a, const T *b)
+ {
+ T result = T(0);
+ for (int i = 0; i < count; ++i)
+ result += a[i] * b[i];
+ return result;
+ }
+}
+
+#define MOP_M_CLASS_TEMPLATE(CLASS, OP, COUNT) \
+ CLASS & operator OP (const CLASS& rhs) \
+ { \
+ for (int i = 0; i < (COUNT); ++i ) \
+ (*this)[i] OP rhs[i]; \
+ return *this; \
+ }
+
+#define MOP_M_TYPE_TEMPLATE(CLASS, OP, COUNT) \
+ CLASS & operator OP (const T & rhs) \
+ { \
+ for (int i = 0; i < (COUNT); ++i ) \
+ (*this)[i] OP rhs; \
+ return *this; \
+ }
+
+#define MOP_COMP_TEMPLATE(CLASS, COUNT) \
+ bool operator == (const CLASS & rhs) \
+ { \
+ bool result = true; \
+ for (int i = 0; i < (COUNT); ++i) \
+ result = result && (*this)[i] == rhs[i]; \
+ return result; \
+ } \
+ bool operator != (const CLASS & rhs) \
+ { return !((*this) == rhs); }
+
+#define MOP_G_UMINUS_TEMPLATE(CLASS, COUNT) \
+ CLASS operator - () const \
+ { \
+ CLASS result; \
+ for (int i = 0; i < (COUNT); ++i) \
+ result[i] = -(*this)[i]; \
+ return result; \
+ }
+
+#define COMMON_OPERATORS(CLASS, COUNT) \
+ MOP_M_CLASS_TEMPLATE(CLASS, +=, COUNT) \
+ MOP_M_CLASS_TEMPLATE(CLASS, -=, COUNT) \
+ /*no *= as this is not the same for vectors and matrices */ \
+ MOP_M_CLASS_TEMPLATE(CLASS, /=, COUNT) \
+ MOP_M_TYPE_TEMPLATE(CLASS, +=, COUNT) \
+ MOP_M_TYPE_TEMPLATE(CLASS, -=, COUNT) \
+ MOP_M_TYPE_TEMPLATE(CLASS, *=, COUNT) \
+ MOP_M_TYPE_TEMPLATE(CLASS, /=, COUNT) \
+ MOP_G_UMINUS_TEMPLATE(CLASS, COUNT) \
+ MOP_COMP_TEMPLATE(CLASS, COUNT)
+
+#define VECTOR_COMMON(CLASS, COUNT) \
+ COMMON_OPERATORS(CLASS, COUNT) \
+ MOP_M_CLASS_TEMPLATE(CLASS, *=, COUNT) \
+ operator const T* () const { return &x; } \
+ operator T* () { return &x; }
+
+#define FOP_G_SOURCE_TEMPLATE(OP, CLASS) \
+ { CLASS<T> r = lhs; r OP##= rhs; return r; }
+
+#define FOP_G_CLASS_TEMPLATE(OP, CLASS) \
+ template <typename T> \
+ inline CLASS<T> operator OP (const CLASS<T> &lhs, const CLASS<T> &rhs) \
+ FOP_G_SOURCE_TEMPLATE(OP, CLASS)
+
+#define FOP_G_TYPE_TEMPLATE(OP, CLASS) \
+ template <typename T> \
+ inline CLASS<T> operator OP (const CLASS<T> &lhs, const T &rhs) \
+ FOP_G_SOURCE_TEMPLATE(OP, CLASS)
+
+// forward declarations
+template <typename T> struct vec2;
+template <typename T> struct vec3;
+template <typename T> struct vec4;
+template <typename T> struct mat2;
+template <typename T> struct mat3;
+template <typename T> struct mat4;
+template <typename T> struct quat;
+
+#define FREE_MODIFYING_OPERATORS(CLASS) \
+ FOP_G_CLASS_TEMPLATE(+, CLASS) \
+ FOP_G_CLASS_TEMPLATE(-, CLASS) \
+ FOP_G_CLASS_TEMPLATE(*, CLASS) \
+ FOP_G_CLASS_TEMPLATE(/, CLASS) \
+ FOP_G_TYPE_TEMPLATE(+, CLASS) \
+ FOP_G_TYPE_TEMPLATE(-, CLASS) \
+ FOP_G_TYPE_TEMPLATE(*, CLASS) \
+ FOP_G_TYPE_TEMPLATE(/, CLASS)
+
+FREE_MODIFYING_OPERATORS(vec2)
+FREE_MODIFYING_OPERATORS(vec3)
+FREE_MODIFYING_OPERATORS(vec4)
+FREE_MODIFYING_OPERATORS(mat2)
+FREE_MODIFYING_OPERATORS(mat3)
+FREE_MODIFYING_OPERATORS(mat4)
+FREE_MODIFYING_OPERATORS(quat)
+
+#define FREE_OPERATORS(CLASS) \
+ template <typename T> \
+ inline CLASS<T> operator + (const T& a, const CLASS<T>& b) \
+ { CLASS<T> r = b; r += a; return r; } \
+ \
+ template <typename T> \
+ inline CLASS<T> operator * (const T& a, const CLASS<T>& b) \
+ { CLASS<T> r = b; r *= a; return r; } \
+ \
+ template <typename T> \
+ inline CLASS<T> operator - (const T& a, const CLASS<T>& b) \
+ { return -b + a; } \
+ \
+ template <typename T> \
+ inline CLASS<T> operator / (const T& a, const CLASS<T>& b) \
+ { CLASS<T> r(a); r /= b; return r; }
+
+FREE_OPERATORS(vec2)
+FREE_OPERATORS(vec3)
+FREE_OPERATORS(vec4)
+FREE_OPERATORS(mat2)
+FREE_OPERATORS(mat3)
+FREE_OPERATORS(mat4)
+FREE_OPERATORS(quat)
+
+template <typename T>
+struct vec2 {
+ T x, y;
+
+ vec2() {};
+ explicit vec2(const T i) : x(i), y(i) {}
+ explicit vec2(const T ix, const T iy) : x(ix), y(iy) {}
+ explicit vec2(const vec3<T>& v);
+ explicit vec2(const vec4<T>& v);
+
+ VECTOR_COMMON(vec2, 2)
+};
+
+template <typename T>
+struct vec3 {
+ T x, y, z;
+
+ vec3() {};
+ explicit vec3(const T i) : x(i), y(i), z(i) {}
+ explicit vec3(const T ix, const T iy, const T iz) : x(ix), y(iy), z(iz) {}
+ explicit vec3(const vec2<T>& xy, const T iz) : x(xy.x), y(xy.y), z(iz) {}
+ explicit vec3(const T ix, const vec2<T>& yz) : x(ix), y(yz.y), z(yz.z) {}
+ explicit vec3(const vec4<T>& v);
+
+ VECTOR_COMMON(vec3, 3)
+};
+
+template <typename T>
+struct vec4 {
+ T x, y, z, w;
+
+ vec4() {};
+ explicit vec4(const T i) : x(i), y(i), z(i), w(i) {}
+ explicit vec4(const T ix, const T iy, const T iz, const T iw) : x(ix), y(iy), z(iz), w(iw) {}
+ explicit vec4(const vec3<T>& xyz,const T iw) : x(xyz.x), y(xyz.y), z(xyz.z), w(iw) {}
+ explicit vec4(const T ix, const vec3<T>& yzw) : x(ix), y(yzw.x), z(yzw.y), w(yzw.z) {}
+ explicit vec4(const vec2<T>& xy, const vec2<T>& zw) : x(xy.x), y(xy.y), z(zw.x), w(zw.y) {}
+
+ VECTOR_COMMON(vec4, 4)
+};
+
+// additional constructors that omit the last element
+template <typename T> inline vec2<T>::vec2(const vec3<T>& v) : x(v.x), y(v.y) {}
+template <typename T> inline vec2<T>::vec2(const vec4<T>& v) : x(v.x), y(v.y) {}
+template <typename T> inline vec3<T>::vec3(const vec4<T>& v) : x(v.x), y(v.y), z(v.z) {}
+
+#define VEC_QUAT_FUNC_TEMPLATE(CLASS, COUNT) \
+ template <typename T> \
+ inline T dot(const CLASS & u, const CLASS & v) \
+ { \
+ const T *a = u; \
+ const T *b = v; \
+ using namespace detail; \
+ return multiply_accumulate(COUNT, a, b); \
+ } \
+ template <typename T> \
+ inline T length(const CLASS & v) \
+ { \
+ return sqrt(dot(v, v)); \
+ } \
+ template <typename T> inline CLASS normalize(const CLASS & v) \
+ { \
+ return v * rsqrt(dot(v, v)); \
+ } \
+ template <typename T> inline CLASS lerp(const CLASS & u, const CLASS & v, const T x) \
+ { \
+ return u * (T(1) - x) + v * x; \
+ }
+
+VEC_QUAT_FUNC_TEMPLATE(vec2<T>, 2)
+VEC_QUAT_FUNC_TEMPLATE(vec3<T>, 3)
+VEC_QUAT_FUNC_TEMPLATE(vec4<T>, 4)
+VEC_QUAT_FUNC_TEMPLATE(quat<T>, 4)
+
+#define VEC_FUNC_TEMPLATE(CLASS) \
+ template <typename T> inline CLASS reflect(const CLASS & I, const CLASS & N) \
+ { \
+ return I - T(2) * dot(N, I) * N; \
+ } \
+ template <typename T> inline CLASS refract(const CLASS & I, const CLASS & N, T eta) \
+ { \
+ const T d = dot(N, I); \
+ const T k = T(1) - eta * eta * (T(1) - d * d); \
+ if ( k < T(0) ) \
+ return CLASS(T(0)); \
+ else \
+ return eta * I - (eta * d + static_cast<T>(sqrt(k))) * N; \
+ }
+
+VEC_FUNC_TEMPLATE(vec2<T>)
+VEC_FUNC_TEMPLATE(vec3<T>)
+VEC_FUNC_TEMPLATE(vec4<T>)
+
+template <typename T> inline T lerp(const T & u, const T & v, const T x)
+{
+ return dot(vec2<T>(u, v), vec2<T>((T(1) - x), x));
+}
+
+template <typename T> inline vec3<T> cross(const vec3<T>& u, const vec3<T>& v)
+{
+ return vec3<T>(
+ dot(vec2<T>(u.y, -v.y), vec2<T>(v.z, u.z)),
+ dot(vec2<T>(u.z, -v.z), vec2<T>(v.x, u.x)),
+ dot(vec2<T>(u.x, -v.x), vec2<T>(v.y, u.y)));
+}
+
+
+#define MATRIX_COL4(SRC, C) \
+ vec4<T>(SRC.elem[0][C], SRC.elem[1][C], SRC.elem[2][C], SRC.elem[3][C])
+
+#define MATRIX_ROW4(SRC, R) \
+ vec4<T>(SRC.elem[R][0], SRC.elem[R][1], SRC.elem[R][2], SRC.elem[R][3])
+
+#define MATRIX_COL3(SRC, C) \
+ vec3<T>(SRC.elem[0][C], SRC.elem[1][C], SRC.elem[2][C])
+
+#define MATRIX_ROW3(SRC, R) \
+ vec3<T>(SRC.elem[R][0], SRC.elem[R][1], SRC.elem[R][2])
+
+#define MATRIX_COL2(SRC, C) \
+ vec2<T>(SRC.elem[0][C], SRC.elem[1][C])
+
+#define MATRIX_ROW2(SRC, R) \
+ vec2<T>(SRC.elem[R][0], SRC.elem[R][1])
+
+#define MOP_M_MATRIX_MULTIPLY(CLASS, SIZE) \
+ CLASS & operator *= (const CLASS & rhs) \
+ { \
+ CLASS result; \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ result.elem[r][c] = dot( \
+ MATRIX_ROW ## SIZE((*this), r), \
+ MATRIX_COL ## SIZE(rhs, c)); \
+ return (*this) = result; \
+ }
+
+#define MATRIX_CONSTRUCTOR_FROM_T(CLASS, SIZE) \
+ explicit CLASS(const T v) \
+ { \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ if (r == c) elem[r][c] = v; \
+ else elem[r][c] = T(0); \
+ }
+
+#define MATRIX_CONSTRUCTOR_FROM_LOWER(CLASS1, CLASS2, SIZE1, SIZE2) \
+ explicit CLASS1(const CLASS2<T>& m) \
+ { \
+ for (int r = 0; r < SIZE1; ++r) \
+ for (int c = 0; c < SIZE1; ++c) \
+ if (r < SIZE2 && c < SIZE2) elem[r][c] = m.elem[r][c]; \
+ else elem[r][c] = r == c ? T(1) : T(0); \
+ }
+
+#define MATRIX_COMMON(CLASS, SIZE) \
+ COMMON_OPERATORS(CLASS, SIZE*SIZE) \
+ MOP_M_MATRIX_MULTIPLY(CLASS, SIZE) \
+ MATRIX_CONSTRUCTOR_FROM_T(CLASS, SIZE) \
+ operator const T* () const { return (const T*) elem; } \
+ operator T* () { return (T*) elem; }
+
+template <typename T> struct mat2;
+template <typename T> struct mat3;
+template <typename T> struct mat4;
+
+template <typename T>
+struct mat2 {
+ T elem[2][2];
+
+ mat2() {}
+
+ explicit mat2(
+ const T m00, const T m01,
+ const T m10, const T m11)
+ {
+ elem[0][0] = m00; elem[0][1] = m01;
+ elem[1][0] = m10; elem[1][1] = m11;
+ }
+
+ explicit mat2(const vec2<T>& v0, const vec2<T>& v1)
+ {
+ elem[0][0] = v0[0];
+ elem[1][0] = v0[1];
+ elem[0][1] = v1[0];
+ elem[1][1] = v1[1];
+ }
+
+ explicit mat2(const mat3<T>& m);
+
+ MATRIX_COMMON(mat2, 2)
+};
+
+template <typename T>
+struct mat3 {
+ T elem[3][3];
+
+ mat3() {}
+
+ explicit mat3(
+ const T m00, const T m01, const T m02,
+ const T m10, const T m11, const T m12,
+ const T m20, const T m21, const T m22)
+ {
+ elem[0][0] = m00; elem[0][1] = m01; elem[0][2] = m02;
+ elem[1][0] = m10; elem[1][1] = m11; elem[1][2] = m12;
+ elem[2][0] = m20; elem[2][1] = m21; elem[2][2] = m22;
+ }
+
+ explicit mat3(const vec3<T>& v0, const vec3<T>& v1, const vec3<T>& v2)
+ {
+ elem[0][0] = v0[0];
+ elem[1][0] = v0[1];
+ elem[2][0] = v0[2];
+ elem[0][1] = v1[0];
+ elem[1][1] = v1[1];
+ elem[2][1] = v1[2];
+ elem[0][2] = v2[0];
+ elem[1][2] = v2[1];
+ elem[2][2] = v2[2];
+ }
+
+ explicit mat3(const mat4<T>& m);
+
+ MATRIX_CONSTRUCTOR_FROM_LOWER(mat3, mat2, 3, 2)
+ MATRIX_COMMON(mat3, 3)
+};
+
+template <typename T>
+struct mat4 {
+ T elem[4][4];
+
+ mat4() {}
+
+ explicit mat4(
+ const T m00, const T m01, const T m02, const T m03,
+ const T m10, const T m11, const T m12, const T m13,
+ const T m20, const T m21, const T m22, const T m23,
+ const T m30, const T m31, const T m32, const T m33)
+ {
+ elem[0][0] = m00; elem[0][1] = m01; elem[0][2] = m02; elem[0][3] = m03;
+ elem[1][0] = m10; elem[1][1] = m11; elem[1][2] = m12; elem[1][3] = m13;
+ elem[2][0] = m20; elem[2][1] = m21; elem[2][2] = m22; elem[2][3] = m23;
+ elem[3][0] = m30; elem[3][1] = m31; elem[3][2] = m32; elem[3][3] = m33;
+ }
+
+ explicit mat4(const vec4<T>& v0, const vec4<T>& v1, const vec4<T>& v2, const vec4<T>& v3)
+ {
+ elem[0][0] = v0[0];
+ elem[1][0] = v0[1];
+ elem[2][0] = v0[2];
+ elem[3][0] = v0[3];
+ elem[0][1] = v1[0];
+ elem[1][1] = v1[1];
+ elem[2][1] = v1[2];
+ elem[3][1] = v1[3];
+ elem[0][2] = v2[0];
+ elem[1][2] = v2[1];
+ elem[2][2] = v2[2];
+ elem[3][2] = v2[3];
+ elem[0][3] = v3[0];
+ elem[1][3] = v3[1];
+ elem[2][3] = v3[2];
+ elem[3][3] = v3[3];
+ }
+
+ MATRIX_CONSTRUCTOR_FROM_LOWER(mat4, mat3, 4, 3)
+ MATRIX_COMMON(mat4, 4)
+};
+
+#define MATRIX_CONSTRUCTOR_FROM_HIGHER(CLASS1, CLASS2, SIZE) \
+ template <typename T> \
+ inline CLASS1<T>::CLASS1(const CLASS2<T>& m) \
+ { \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ elem[r][c] = m.elem[r][c]; \
+ }
+
+MATRIX_CONSTRUCTOR_FROM_HIGHER(mat2, mat3, 2)
+MATRIX_CONSTRUCTOR_FROM_HIGHER(mat3, mat4, 3)
+
+#define MAT_FUNC_TEMPLATE(CLASS, SIZE) \
+ template <typename T> \
+ inline CLASS transpose(const CLASS & m) \
+ { \
+ CLASS result; \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ result.elem[r][c] = m.elem[c][r]; \
+ return result; \
+ } \
+ template <typename T> \
+ inline CLASS identity ## SIZE() \
+ { \
+ CLASS result; \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ result.elem[r][c] = r == c ? T(1) : T(0); \
+ return result; \
+ } \
+ template <typename T> \
+ inline T trace(const CLASS & m) \
+ { \
+ T result = T(0); \
+ for (int i = 0; i < SIZE; ++i) \
+ result += m.elem[i][i]; \
+ return result; \
+ }
+
+MAT_FUNC_TEMPLATE(mat2<T>, 2)
+MAT_FUNC_TEMPLATE(mat3<T>, 3)
+MAT_FUNC_TEMPLATE(mat4<T>, 4)
+
+#define MAT_FUNC_MINOR_TEMPLATE(CLASS1, CLASS2, SIZE) \
+ template <typename T> \
+ inline CLASS2 minor(const CLASS1 & m, int _r = SIZE, int _c = SIZE) { \
+ CLASS2 result; \
+ for (int r = 0; r < SIZE - 1; ++r) \
+ for (int c = 0; c < SIZE - 1; ++c) { \
+ int rs = r >= _r ? 1 : 0; \
+ int cs = c >= _c ? 1 : 0; \
+ result.elem[r][c] = m.elem[r + rs][c + cs]; \
+ } \
+ return result; \
+ }
+
+MAT_FUNC_MINOR_TEMPLATE(mat3<T>, mat2<T>, 3)
+MAT_FUNC_MINOR_TEMPLATE(mat4<T>, mat3<T>, 4)
+
+template <typename T>
+inline T det(const mat2<T>& m)
+{
+ return dot(
+ vec2<T>(m.elem[0][0], -m.elem[0][1]),
+ vec2<T>(m.elem[1][1], m.elem[1][0]));
+}
+
+template <typename T>
+inline T det(const mat3<T>& m)
+{
+ return dot(cross(MATRIX_COL3(m, 0), MATRIX_COL3(m, 1)), MATRIX_COL3(m, 2));
+}
+
+template <typename T>
+inline T det(const mat4<T>& m)
+{
+ vec4<T> b;
+ for (int i = 0; i < 4; ++i)
+ b[i] = (i & 1 ? -1 : 1) * det(minor(m, 0, i));
+ return dot(MATRIX_ROW4(m, 0), b);
+}
+
+#define MAT_ADJOINT_TEMPLATE(CLASS, SIZE) \
+ template <typename T> \
+ inline CLASS adjoint(const CLASS & m) \
+ { \
+ CLASS result; \
+ for (int r = 0; r < SIZE; ++r) \
+ for (int c = 0; c < SIZE; ++c) \
+ result.elem[r][c] = ((r + c) & 1 ? -1 : 1) * det(minor(m, c, r)); \
+ return result; \
+ }
+
+MAT_ADJOINT_TEMPLATE(mat3<T>, 3)
+MAT_ADJOINT_TEMPLATE(mat4<T>, 4)
+
+template <typename T>
+inline mat2<T> adjoint(const mat2<T> & m)
+{
+ return mat2<T>(
+ m.elem[1][1], -m.elem[0][1],
+ -m.elem[1][0], m.elem[0][0]
+ );
+}
+
+#define MAT_INVERSE_TEMPLATE(CLASS) \
+ template <typename T> \
+ inline CLASS inverse(const CLASS & m) \
+ { \
+ return adjoint(m) * inv(det(m)); \
+ }
+
+MAT_INVERSE_TEMPLATE(mat2<T>)
+MAT_INVERSE_TEMPLATE(mat3<T>)
+MAT_INVERSE_TEMPLATE(mat4<T>)
+
+#define MAT_VEC_FUNCS_TEMPLATE(MATCLASS, VECCLASS, SIZE) \
+ template <typename T> \
+ inline VECCLASS operator * (const MATCLASS & m, const VECCLASS & v) \
+ { \
+ VECCLASS result; \
+ for (int i = 0; i < SIZE; ++i) {\
+ result[i] = dot(MATRIX_ROW ## SIZE(m, i), v); \
+ } \
+ return result; \
+ } \
+ template <typename T> \
+ inline VECCLASS operator * (const VECCLASS & v, const MATCLASS & m) \
+ { \
+ VECCLASS result; \
+ for (int i = 0; i < SIZE; ++i) \
+ result[i] = dot(v, MATRIX_COL ## SIZE(m, i)); \
+ return result; \
+ }
+
+MAT_VEC_FUNCS_TEMPLATE(mat2<T>, vec2<T>, 2)
+MAT_VEC_FUNCS_TEMPLATE(mat3<T>, vec3<T>, 3)
+MAT_VEC_FUNCS_TEMPLATE(mat4<T>, vec4<T>, 4)
+
+// Returns the inverse of a 4x4 matrix. It is assumed that the matrix passed
+// as argument describes a rigid-body transformation.
+template <typename T>
+inline mat4<T> fast_inverse(const mat4<T>& m)
+{
+ const vec3<T> t = MATRIX_COL3(m, 3);
+ const T tx = -dot(MATRIX_COL3(m, 0), t);
+ const T ty = -dot(MATRIX_COL3(m, 1), t);
+ const T tz = -dot(MATRIX_COL3(m, 2), t);
+
+ return mat4<T>(
+ m.elem[0][0], m.elem[1][0], m.elem[2][0], tx,
+ m.elem[0][1], m.elem[1][1], m.elem[2][1], ty,
+ m.elem[0][2], m.elem[1][2], m.elem[2][2], tz,
+ T(0), T(0), T(0), T(1)
+ );
+}
+
+// Transformations for points and vectors. Potentially faster than a full
+// matrix * vector multiplication
+
+#define MAT_TRANFORMS_TEMPLATE(MATCLASS, VECCLASS, VECSIZE) \
+ /* computes vec3<T>(m * vec4<T>(v, 0.0)) */ \
+ template <typename T> \
+ inline VECCLASS transform_vector(const MATCLASS & m, const VECCLASS & v) \
+ { \
+ VECCLASS result; \
+ for (int i = 0; i < VECSIZE; ++i) \
+ result[i] = dot(MATRIX_ROW ## VECSIZE(m, i), v); \
+ return result;\
+ } \
+ /* computes vec3(m * vec4(v, 1.0)) */ \
+ template <typename T> \
+ inline VECCLASS transform_point(const MATCLASS & m, const VECCLASS & v) \
+ { \
+ /*return transform_vector(m, v) + MATRIX_ROW ## VECSIZE(m, VECSIZE); */\
+ VECCLASS result; \
+ for (int i = 0; i < VECSIZE; ++i) \
+ result[i] = dot(MATRIX_ROW ## VECSIZE(m, i), v) + m.elem[i][VECSIZE]; \
+ return result; \
+ } \
+ /* computes VECCLASS(transpose(m) * vec4<T>(v, 0.0)) */ \
+ template <typename T> \
+ inline VECCLASS transform_vector_transpose(const MATCLASS & m, const VECCLASS& v) \
+ { \
+ VECCLASS result; \
+ for (int i = 0; i < VECSIZE; ++i) \
+ result[i] = dot(MATRIX_COL ## VECSIZE(m, i), v); \
+ return result; \
+ } \
+ /* computes VECCLASS(transpose(m) * vec4<T>(v, 1.0)) */ \
+ template <typename T> \
+ inline VECCLASS transform_point_transpose(const MATCLASS & m, const VECCLASS& v) \
+ { \
+ /*return transform_vector_transpose(m, v) + MATRIX_COL ## VECSIZE(m, VECSIZE); */\
+ VECCLASS result; \
+ for (int i = 0; i < VECSIZE; ++i) \
+ result[i] = dot(MATRIX_COL ## VECSIZE(m, i), v) + m.elem[VECSIZE][i]; \
+ return result; \
+ }
+
+MAT_TRANFORMS_TEMPLATE(mat4<T>, vec3<T>, 3)
+MAT_TRANFORMS_TEMPLATE(mat3<T>, vec2<T>, 2)
+
+#define MAT_OUTERPRODUCT_TEMPLATE(MATCLASS, VECCLASS, MATSIZE) \
+ template <typename T> \
+ inline MATCLASS outer_product(const VECCLASS & v1, const VECCLASS & v2) \
+ { \
+ MATCLASS r; \
+ for ( int j = 0; j < MATSIZE; ++j ) \
+ for ( int k = 0; k < MATSIZE; ++k ) \
+ r.elem[j][k] = v1[j] * v2[k]; \
+ return r; \
+ }
+
+MAT_OUTERPRODUCT_TEMPLATE(mat4<T>, vec4<T>, 4)
+MAT_OUTERPRODUCT_TEMPLATE(mat3<T>, vec3<T>, 3)
+MAT_OUTERPRODUCT_TEMPLATE(mat2<T>, vec2<T>, 2)
+
+template <typename T>
+inline mat4<T> translation_matrix(const T x, const T y, const T z)
+{
+ mat4<T> r(T(1));
+ r.elem[0][3] = x;
+ r.elem[1][3] = y;
+ r.elem[2][3] = z;
+ return r;
+}
+
+template <typename T>
+inline mat4<T> translation_matrix(const vec3<T>& v)
+{
+ return translation_matrix(v.x, v.y, v.z);
+}
+
+template <typename T>
+inline mat4<T> scaling_matrix(const T x, const T y, const T z)
+{
+ mat4<T> r(T(0));
+ r.elem[0][0] = x;
+ r.elem[1][1] = y;
+ r.elem[2][2] = z;
+ r.elem[3][3] = T(1);
+ return r;
+}
+
+template <typename T>
+inline mat4<T> scaling_matrix(const vec3<T>& v)
+{
+ return scaling_matrix(v.x, v.y, v.z);
+}
+
+template <typename T>
+inline mat4<T> rotation_matrix(const T angle, const vec3<T>& v)
+{
+ const T a = angle * T(M_PI/180) ;
+ const vec3<T> u = normalize(v);
+
+ const mat3<T> S(
+ T(0), -u[2], u[1],
+ u[2], T(0), -u[0],
+ -u[1], u[0], T(0)
+ );
+
+ const mat3<T> uut = outer_product(u, u);
+ const mat3<T> R = uut + T(cos(a)) * (identity3<T>() - uut) + T(sin(a)) * S;
+
+ return mat4<T>(R);
+}
+
+
+template <typename T>
+inline mat4<T> rotation_matrix(const T angle, const T x, const T y, const T z)
+{
+ return rotation_matrix(angle, vec3<T>(x, y, z));
+}
+
+// Constructs a shear-matrix that shears component i by factor with
+// Respect to component j.
+template <typename T>
+inline mat4<T> shear_matrix(const int i, const int j, const T factor)
+{
+ mat4<T> m = identity4<T>();
+ m.elem[i][j] = factor;
+ return m;
+}
+
+template <typename T>
+inline mat4<T> euler(const T head, const T pitch, const T roll)
+{
+ return rotation_matrix(roll, T(0), T(0), T(1)) *
+ rotation_matrix(pitch, T(1), T(0), T(0)) *
+ rotation_matrix(head, T(0), T(1), T(0));
+}
+
+template <typename T>
+inline mat4<T> frustum_matrix(const T l, const T r, const T b, const T t, const T n, const T f)
+{
+ return mat4<T>(
+ (2 * n)/(r - l), T(0), (r + l)/(r - l), T(0),
+ T(0), (2 * n)/(t - b), (t + b)/(t - b), T(0),
+ T(0), T(0), -(f + n)/(f - n), -(2 * f * n)/(f - n),
+ T(0), T(0), -T(1), T(0)
+ );
+}
+
+template <typename T>
+inline mat4<T> perspective_matrix(const T fovy, const T aspect, const T zNear, const T zFar)
+{
+ const T dz = zFar - zNear;
+ const T rad = fovy / T(2) * T(M_PI/180);
+ const T s = sin(rad);
+
+ if ( ( dz == T(0) ) || ( s == T(0) ) || ( aspect == T(0) ) ) {
+ return identity4<T>();
+ }
+
+ const T cot = cos(rad) / s;
+
+ mat4<T> m = identity4<T>();
+ m[0] = cot / aspect;
+ m[5] = cot;
+ m[10] = -(zFar + zNear) / dz;
+ m[14] = T(-1);
+ m[11] = -2 * zNear * zFar / dz;
+ m[15] = T(0);
+
+ return m;
+}
+
+template <typename T>
+inline mat4<T> ortho_matrix(const T l, const T r, const T b, const T t, const T n, const T f)
+{
+ return mat4<T>(
+ T(2)/(r - l), T(0), T(0), -(r + l)/(r - l),
+ T(0), T(2)/(t - b), T(0), -(t + b)/(t - b),
+ T(0), T(0), -T(2)/(f - n), -(f + n)/(f - n),
+ T(0), T(0), T(0), T(1)
+ );
+}
+
+template <typename T>
+inline mat4<T> lookat_matrix(const vec3<T>& eye, const vec3<T>& center, const vec3<T>& up) {
+ const vec3<T> forward = normalize(center - eye);
+ const vec3<T> side = normalize(cross(forward, up));
+
+ const vec3<T> up2 = cross(side, forward);
+
+ mat4<T> m = identity4<T>();
+
+ m.elem[0][0] = side[0];
+ m.elem[0][1] = side[1];
+ m.elem[0][2] = side[2];
+
+ m.elem[1][0] = up2[0];
+ m.elem[1][1] = up2[1];
+ m.elem[1][2] = up2[2];
+
+ m.elem[2][0] = -forward[0];
+ m.elem[2][1] = -forward[1];
+ m.elem[2][2] = -forward[2];
+
+ return m * translation_matrix(-eye);
+}
+
+template <typename T>
+inline mat4<T> picking_matrix(const T x, const T y, const T dx, const T dy, int viewport[4]) {
+ if (dx <= 0 || dy <= 0) {
+ return identity4<T>();
+ }
+
+ mat4<T> r = translation_matrix((viewport[2] - 2 * (x - viewport[0])) / dx,
+ (viewport[3] - 2 * (y - viewport[1])) / dy, 0);
+ r *= scaling_matrix(viewport[2] / dx, viewport[2] / dy, 1);
+ return r;
+}
+
+// Constructs a shadow matrix. q is the light source and p is the plane.
+template <typename T> inline mat4<T> shadow_matrix(const vec4<T>& q, const vec4<T>& p) {
+ mat4<T> m;
+
+ m.elem[0][0] = p.y * q[1] + p.z * q[2] + p.w * q[3];
+ m.elem[0][1] = -p.y * q[0];
+ m.elem[0][2] = -p.z * q[0];
+ m.elem[0][3] = -p.w * q[0];
+
+ m.elem[1][0] = -p.x * q[1];
+ m.elem[1][1] = p.x * q[0] + p.z * q[2] + p.w * q[3];
+ m.elem[1][2] = -p.z * q[1];
+ m.elem[1][3] = -p.w * q[1];
+
+
+ m.elem[2][0] = -p.x * q[2];
+ m.elem[2][1] = -p.y * q[2];
+ m.elem[2][2] = p.x * q[0] + p.y * q[1] + p.w * q[3];
+ m.elem[2][3] = -p.w * q[2];
+
+ m.elem[3][1] = -p.x * q[3];
+ m.elem[3][2] = -p.y * q[3];
+ m.elem[3][3] = -p.z * q[3];
+ m.elem[3][0] = p.x * q[0] + p.y * q[1] + p.z * q[2];
+
+ return m;
+}
+
+// Quaternion class
+template <typename T>
+struct quat {
+ vec3<T> v;
+ T w;
+
+ quat() {}
+ quat(const vec3<T>& iv, const T iw) : v(iv), w(iw) {}
+ quat(const T vx, const T vy, const T vz, const T iw) : v(vx, vy, vz), w(iw) {}
+ quat(const vec4<T>& i) : v(i.x, i.y, i.z), w(i.w) {}
+
+ operator const T* () const { return &(v[0]); }
+ operator T* () { return &(v[0]); }
+
+ quat& operator += (const quat& q) { v += q.v; w += q.w; return *this; }
+ quat& operator -= (const quat& q) { v -= q.v; w -= q.w; return *this; }
+
+ quat& operator *= (const T& s) { v *= s; w *= s; return *this; }
+ quat& operator /= (const T& s) { v /= s; w /= s; return *this; }
+
+ quat& operator *= (const quat& r)
+ {
+ //q1 x q2 = [s1,v1] x [s2,v2] = [(s1*s2 - v1*v2),(s1*v2 + s2*v1 + v1xv2)].
+ quat q;
+ q.v = cross(v, r.v) + r.w * v + w * r.v;
+ q.w = w * r.w - dot(v, r.v);
+ return *this = q;
+ }
+
+ quat& operator /= (const quat& q) { return (*this) *= inverse(q); }
+};
+
+// Quaternion functions
+
+template <typename T>
+inline quat<T> identityq()
+{
+ return quat<T>(T(0), T(0), T(0), T(1));
+}
+
+template <typename T>
+inline quat<T> conjugate(const quat<T>& q)
+{
+ return quat<T>(-q.v, q.w);
+}
+
+template <typename T>
+inline quat<T> inverse(const quat<T>& q)
+{
+ const T l = dot(q, q);
+ if ( l > T(0) ) return conjugate(q) * inv(l);
+ else return identityq<T>();
+}
+
+// quaternion utility functions
+
+// the input quaternion is assumed to be normalized
+template <typename T>
+inline mat3<T> quat_to_mat3(const quat<T>& q)
+{
+ // const quat<T> q = normalize(qq);
+
+ const T xx = q[0] * q[0];
+ const T xy = q[0] * q[1];
+ const T xz = q[0] * q[2];
+ const T xw = q[0] * q[3];
+
+ const T yy = q[1] * q[1];
+ const T yz = q[1] * q[2];
+ const T yw = q[1] * q[3];
+
+ const T zz = q[2] * q[2];
+ const T zw = q[2] * q[3];
+
+ return mat3<T>(
+ 1 - 2*(yy + zz), 2*(xy - zw), 2*(xz + yw),
+ 2*(xy + zw), 1 - 2*(xx + zz), 2*(yz - xw),
+ 2*(xz - yw), 2*(yz + xw), 1 - 2*(xx + yy)
+ );
+}
+
+// the input quat<T>ernion is assumed to be normalized
+template <typename T>
+inline mat4<T> quat_to_mat4(const quat<T>& q)
+{
+ // const quat<T> q = normalize(qq);
+
+ return mat4<T>(quat_to_mat3(q));
+}
+
+template <typename T>
+inline quat<T> mat_to_quat(const mat4<T>& m)
+{
+ const T t = m.elem[0][0] + m.elem[1][1] + m.elem[2][2] + T(1);
+ quat<T> q;
+
+ if ( t > 0 ) {
+ const T s = T(0.5) / sqrt(t);
+ q[3] = T(0.25) * inv(s);
+ q[0] = (m.elem[2][1] - m.elem[1][2]) * s;
+ q[1] = (m.elem[0][2] - m.elem[2][0]) * s;
+ q[2] = (m.elem[1][0] - m.elem[0][1]) * s;
+ } else {
+ if ( m.elem[0][0] > m.elem[1][1] && m.elem[0][0] > m.elem[2][2] ) {
+ const T s = T(2) * sqrt( T(1) + m.elem[0][0] - m.elem[1][1] - m.elem[2][2]);
+ const T invs = inv(s);
+ q[0] = T(0.25) * s;
+ q[1] = (m.elem[0][1] + m.elem[1][0] ) * invs;
+ q[2] = (m.elem[0][2] + m.elem[2][0] ) * invs;
+ q[3] = (m.elem[1][2] - m.elem[2][1] ) * invs;
+ } else if (m.elem[1][1] > m.elem[2][2]) {
+ const T s = T(2) * sqrt( T(1) + m.elem[1][1] - m.elem[0][0] - m.elem[2][2]);
+ const T invs = inv(s);
+ q[0] = (m.elem[0][1] + m.elem[1][0] ) * invs;
+ q[1] = T(0.25) * s;
+ q[2] = (m.elem[1][2] + m.elem[2][1] ) * invs;
+ q[3] = (m.elem[0][2] - m.elem[2][0] ) * invs;
+ } else {
+ const T s = T(2) * sqrt( T(1) + m.elem[2][2] - m.elem[0][0] - m.elem[1][1] );
+ const T invs = inv(s);
+ q[0] = (m.elem[0][2] + m.elem[2][0] ) * invs;
+ q[1] = (m.elem[1][2] + m.elem[2][1] ) * invs;
+ q[2] = T(0.25) * s;
+ q[3] = (m.elem[0][1] - m.elem[1][0] ) * invs;
+ }
+ }
+
+ return q;
+}
+
+template <typename T>
+inline quat<T> mat_to_quat(const mat3<T>& m)
+{
+ return mat_to_quat(mat4<T>(m));
+}
+
+// the angle is in radians
+template <typename T>
+inline quat<T> quat_from_axis_angle(const vec3<T>& axis, const T a)
+{
+ quat<T> r;
+ const T inv2 = inv(T(2));
+ r.v = sin(a * inv2) * normalize(axis);
+ r.w = cos(a * inv2);
+
+ return r;
+}
+
+// the angle is in radians
+template <typename T>
+inline quat<T> quat_from_axis_angle(const T x, const T y, const T z, const T angle)
+{
+ return quat_from_axis_angle<T>(vec3<T>(x, y, z), angle);
+}
+
+// the angle is stored in radians
+template <typename T>
+inline void quat_to_axis_angle(const quat<T>& qq, vec3<T>* axis, T *angle)
+{
+ quat<T> q = normalize(qq);
+
+ *angle = 2 * acos(q.w);
+
+ const T s = sin((*angle) * inv(T(2)));
+ if ( s != T(0) )
+ *axis = q.v * inv(s);
+ else
+ * axis = vec3<T>(T(0), T(0), T(0));
+}
+
+// Spherical linear interpolation
+template <typename T>
+inline quat<T> slerp(const quat<T>& qq1, const quat<T>& qq2, const T t)
+{
+ // slerp(q1,q2) = sin((1-t)*a)/sin(a) * q1 + sin(t*a)/sin(a) * q2
+ const quat<T> q1 = normalize(qq1);
+ const quat<T> q2 = normalize(qq2);
+
+ const T a = acos(dot(q1, q2));
+ const T s = sin(a);
+
+ #define EPS T(1e-5)
+
+ if ( !(-EPS <= s && s <= EPS) ) {
+ return sin((T(1)-t)*a)/s * q1 + sin(t*a)/s * q2;
+ } else {
+ // if the angle is to small use a linear interpolation
+ return lerp(q1, q2, t);
+ }
+
+ #undef EPS
+}
+
+// Sperical quadtratic interpolation using a smooth cubic spline
+// The parameters a and b are the control points.
+template <typename T>
+inline quat<T> squad(
+ const quat<T>& q0,
+ const quat<T>& a,
+ const quat<T>& b,
+ const quat<T>& q1,
+ const T t)
+{
+ return slerp(slerp(q0, q1, t),slerp(a, b, t), 2 * t * (1 - t));
+}
+
+#undef MOP_M_CLASS_TEMPLATE
+#undef MOP_M_TYPE_TEMPLATE
+#undef MOP_COMP_TEMPLATE
+#undef MOP_G_UMINUS_TEMPLATE
+#undef COMMON_OPERATORS
+#undef VECTOR_COMMON
+#undef FOP_G_SOURCE_TEMPLATE
+#undef FOP_G_CLASS_TEMPLATE
+#undef FOP_G_TYPE_TEMPLATE
+#undef VEC_QUAT_FUNC_TEMPLATE
+#undef VEC_FUNC_TEMPLATE
+#undef MATRIX_COL4
+#undef MATRIX_ROW4
+#undef MATRIX_COL3
+#undef MATRIX_ROW3
+#undef MATRIX_COL2
+#undef MATRIX_ROW2
+#undef MOP_M_MATRIX_MULTIPLY
+#undef MATRIX_CONSTRUCTOR_FROM_T
+#undef MATRIX_CONSTRUCTOR_FROM_LOWER
+#undef MATRIX_COMMON
+#undef MATRIX_CONSTRUCTOR_FROM_HIGHER
+#undef MAT_FUNC_TEMPLATE
+#undef MAT_FUNC_MINOR_TEMPLATE
+#undef MAT_ADJOINT_TEMPLATE
+#undef MAT_INVERSE_TEMPLATE
+#undef MAT_VEC_FUNCS_TEMPLATE
+#undef MAT_TRANFORMS_TEMPLATE
+#undef MAT_OUTERPRODUCT_TEMPLATE
+#undef FREE_MODIFYING_OPERATORS
+#undef FREE_OPERATORS
+
+} // end namespace vmath
+
+#endif
+
+
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/PwmIn/PwmIn.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,57 @@
+/* mbed PwmIn Library
+ * Copyright (c) 2008-2010, sford
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#include "PwmIn.h"
+
+PwmIn::PwmIn(PinName p) : _p(p) {
+ _p.mode(PullNone);
+ _p.rise(this, &PwmIn::rise);
+ _p.fall(this, &PwmIn::fall);
+ _period = 0.0;
+ _pulsewidth = 0.0;
+ _temp_pulsewidth = 0.0;
+ _t.start();
+}
+
+float PwmIn::period() {
+ return _period;
+}
+
+float PwmIn::pulsewidth() {
+ return _pulsewidth;
+}
+
+float PwmIn::dutycycle() {
+ if(_t.read_ms()<100){
+ return (_pulsewidth%_period) /((float) _period);}
+ else return 0;
+}
+
+void PwmIn::rise() {
+ _period = _t.read_us();
+ _t.reset();
+}
+
+void PwmIn::fall() {
+ _temp_pulsewidth = _t.read_us();
+ if(_temp_pulsewidth != 0) _pulsewidth = _temp_pulsewidth;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/PwmIn/PwmIn.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,70 @@
+/* mbed PwmIn Library
+ * Copyright (c) 2008-2010, sford
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#ifndef MBED_PWMIN_H
+#define MBED_PWMIN_H
+
+#include "mbed.h"
+
+/** PwmIn class to read PWM inputs
+ *
+ * Uses InterruptIn to measure the changes on the input
+ * and record the time they occur
+ *
+ * @note uses InterruptIn, so not available on p19/p20
+ */
+class PwmIn {
+public:
+ /** Create a PwmIn
+ *
+ * @param p The pwm input pin (must support InterruptIn)
+ */
+ PwmIn(PinName p);
+
+ /** Read the current period
+ *
+ * @returns the period in seconds
+ */
+ float period();
+
+ /** Read the current pulsewidth
+ *
+ * @returns the pulsewidth in seconds
+ */
+ float pulsewidth();
+
+ /** Read the current dutycycle
+ *
+ * @returns the dutycycle as a percentage, represented between 0.0-1.0
+ */
+ float dutycycle();
+
+protected:
+ void rise();
+ void fall();
+
+ InterruptIn _p;
+ Timer _t;
+ int _pulsewidth, _period, _temp_pulsewidth;
+};
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/Utils/Utils.h Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,24 @@
+#ifndef _UTILS_H_
+#define _UTILS_H_
+
+#include "mbed.h"
+
+float max(float a, float b){
+ if(a>b) return a;
+ else return b;
+}
+
+float min(float a, float b){
+ if(a<b) return a;
+ else return b;
+}
+
+float clip(float m, float M, float a){
+ return max(min(M,a),m);
+}
+
+/*float abs(float a){
+ return max(a,-a);
+}*/
+
+#endif
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp Wed Jul 17 15:58:25 2013 +0000
@@ -0,0 +1,166 @@
+#include "mbed.h"
+#include "PwmIn.h"
+#include "Utils.h"
+#include "GurvIMU.h"
+#include "DaclePID.h"
+
+//#define DEBUG
+
+//Vue d'artiste
+/* AXE X
+ 3
+ ^
+ |
+4 -------> 2 // AXE Y
+ |
+ 1
+*/
+
+
+//------------- DEFINITION DES PINs -----------------
+DigitalOut ledG(LED_GREEN);
+
+
+//-- TELECOMMANDE --
+PwmIn telecommande_throttle(PTD5); // throttle, channel 3
+
+//------ ESCs ------
+PwmOut esc1(PTD4); //rouge
+PwmOut esc2(PTA12); //verte
+PwmOut esc3(PTA4); //rouge
+PwmOut esc4(PTA5); //verte
+
+//---- CAPTEURS ----
+GurvIMU imu;
+
+//------ PIDs ------
+Timer pidTimer;
+float dt_pid = 0.01;
+DaclePID pidX(0.5,0.0,0.01,dt_pid);
+DaclePID pidY(0.5,0.0,0.01,dt_pid);
+
+
+//---------- DEFINITION DES VARIABLES ---------------
+
+float yaw;
+float pitch; //rotation autour de l'axe X/rouge
+float roll; //rotation autour de l'axe Y/vert
+float ypr[3];// = {yaw,pitch,roll};
+
+float commande_pidX;
+float commande_pidY;
+
+int _period_us=18502; // periode de la PWM en microseconde
+
+float consigne_throttle = 0.0635; //PWM minimale
+
+
+//----------------- SERIAL DEGBUG -------------------
+#ifdef DEBUG
+ Serial debugSerial(USBTX, USBRX);
+#endif
+
+
+//--------------- DEBUT PROGRAMME -------------------
+int main() {
+ #ifdef DEBUG
+ debugSerial.baud(921600);
+ debugSerial.printf("Initialisation du programme\r\n");
+ #endif
+
+ //-- CAPTEURS --
+ #ifdef DEBUG
+ debugSerial.printf("Initialisation capteurs\r\n");
+ #endif
+ imu.init();
+ while((abs(ypr[2])<0.001) || (abs(ypr[1])<0.001) ){
+ imu.getYawPitchRollRad(ypr);
+ ledG=!ledG;
+ wait_ms(50);
+ }
+ #ifdef DEBUG
+ debugSerial.printf("Fin initialisation capteurs\r\n");
+ #endif
+
+ //--- ESCs ---
+ #ifdef DEBUG
+ debugSerial.printf("Initialisation des ESCs\r\n");
+ #endif
+ esc1.period_us(_period_us);
+ esc2.period_us(_period_us);
+ esc3.period_us(_period_us);
+ esc4.period_us(_period_us);
+
+ esc1.write(0.0635);
+ esc2.write(0.0635);
+ esc3.write(0.0635);
+ esc4.write(0.0635);
+
+ wait(1);
+ #ifdef DEBUG
+ debugSerial.printf("Fin initialisation des ESCs\r\n");
+ #endif
+
+ //---- PIDs ----
+ #ifdef DEBUG
+ debugSerial.printf("Initialisation des PIDs\r\n");
+ #endif
+ pidTimer.start();
+ //pidX.setInputLimits(-1.57,1.57);
+ //pidY.setInputLimits(-1.57,1.57);
+ pidX.setInputLimits(-0.60,0.60);
+ pidY.setInputLimits(-0.60,0.60);
+ //pidX.setOutputLimits(-1.0,1.0);
+ //pidY.setOutputLimits(-1.0,1.0);
+
+ pidX.setOutputLimits(-0.30*0.0385,0.30*0.0385);
+ pidY.setOutputLimits(-0.30*0.0385,0.30*0.0385);
+
+ #ifdef DEBUG
+ debugSerial.printf("Fin initialisation des PIDs\r\n");
+ #endif
+
+
+ #ifdef DEBUG
+ debugSerial.printf("Fin initialisation du programme\r\n");
+ debugSerial.printf("Entrée dans la boucle principale\r\n");
+ #endif
+ while(1) {
+ //------ RECUPERATION DONNEES TELECOMMANDE ----------
+ #ifdef DEBUG
+ debugSerial.printf("Recuperation des donnees telecommande\r\n");
+ #endif
+ consigne_throttle =min( telecommande_throttle.dutycycle(),0.090);
+ #ifdef DEBUG
+ debugSerial.printf("Throttle: %f\r\n",consigne_throttle);
+ wait_ms(100);
+ #endif
+
+ //------ RECUPERATION DONNEES CAPTEURS ----------
+ #ifdef DEBUG
+ debugSerial.printf("Recuperation des donnees capteurs\r\n");
+ #endif
+ imu.getYawPitchRollRad(ypr);
+ #ifdef DEBUG
+ debugSerial.printf("Yaw: %f;, Pitch: %f, Roll: %f\r\n",ypr[0],ypr[1],ypr[2]);
+ wait_ms(5);
+ #endif
+ //--------------- CALCUL PIDs -------------------
+ while(pidTimer.read() < dt_pid);
+ pidTimer.reset();
+ commande_pidX=clip(-0.50*0.0385,0.50*0.0385,pidX.dacalcul(ypr[2])); //roll
+ commande_pidY=clip(-0.50*0.0385,0.50*0.0385,pidY.dacalcul(ypr[1])); //pitch
+ #ifdef DEBUG
+ debugSerial.printf("Commande PID: %f\r\n",commande_pidX);
+ wait_ms(5);
+ #endif
+
+ //--------------- COMMANDE ESCs -----------------
+
+ esc1.write(clip(0.0635,0.102,consigne_throttle - commande_pidY));
+ esc2.write(clip(0.0635,0.102,consigne_throttle - commande_pidX));
+ esc3.write(clip(0.0635,0.102,consigne_throttle + commande_pidY));
+ esc4.write(clip(0.0635,0.102,consigne_throttle + commande_pidX));
+
+ }
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed.bld Wed Jul 17 15:58:25 2013 +0000 @@ -0,0 +1,1 @@ +http://mbed.org/users/mbed_official/code/mbed/builds/b3110cd2dd17 \ No newline at end of file