Diego Ostuni
Fork of the GitHub
Diff: rfal_st25tb.h
- Revision:
- 0:75fc82583a41
diff -r 000000000000 -r 75fc82583a41 rfal_st25tb.h
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/rfal_st25tb.h Thu Nov 14 14:34:50 2019 +0000
@@ -0,0 +1,355 @@
+
+/******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT 2016 STMicroelectronics</center></h2>
+ *
+ * Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
+ * You may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at:
+ *
+ * http://www.st.com/myliberty
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
+ * AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+******************************************************************************/
+
+/*
+ * PROJECT: ST25R391x firmware
+ * $Revision: $
+ * LANGUAGE: ISO C99
+ */
+
+/*! \file rfal_st25tb.h
+ *
+ * \author Gustavo Patricio
+ *
+ * \brief Implementation of ST25TB interface
+ *
+ *
+ * @addtogroup RFAL
+ * @{
+ *
+ * @addtogroup RFAL-AL
+ * @brief RFAL Abstraction Layer
+ * @{
+ *
+ * @addtogroup ST25TB
+ * @brief RFAL ST25TB Module
+ * @{
+ *
+ */
+
+
+#ifndef RFAL_ST25TB_H
+#define RFAL_ST25TB_H
+
+/*
+ ******************************************************************************
+ * INCLUDES
+ ******************************************************************************
+ */
+#include "platform1.h"
+#include "st_errno.h"
+#include "rfal_rf.h"
+#include "rfal_nfcb.h"
+
+/*
+ ******************************************************************************
+ * GLOBAL DEFINES
+ ******************************************************************************
+ */
+
+#define RFAL_ST25TB_CHIP_ID_LEN 1 /*!< ST25TB chip ID length */
+#define RFAL_ST25TB_CRC_LEN 2 /*!< ST25TB CRC length */
+#define RFAL_ST25TB_UID_LEN 8 /*!< ST25TB Unique ID length */
+#define RFAL_ST25TB_BLOCK_LEN 4 /*!< ST25TB Data Block length */
+
+/*
+******************************************************************************
+* GLOBAL MACROS
+******************************************************************************
+*/
+
+
+
+/*
+******************************************************************************
+* GLOBAL TYPES
+******************************************************************************
+*/
+typedef uint8_t rfalSt25tbUID[RFAL_ST25TB_UID_LEN]; /*!< ST25TB UID type */
+typedef uint8_t rfalSt25tbBlock[RFAL_ST25TB_BLOCK_LEN]; /*!< ST25TB Block type */
+
+
+/*! ST25TB listener device (PICC) struct */
+typedef struct
+{
+ uint8_t chipID; /*!< Device's session Chip ID */
+ rfalSt25tbUID UID; /*!< Device's UID */
+ bool isDeselected; /*!< Device deselect flag */
+}rfalSt25tbListenDevice;
+
+
+/*
+******************************************************************************
+* GLOBAL FUNCTION PROTOTYPES
+******************************************************************************
+*/
+
+/*!
+ *****************************************************************************
+ * \brief Initialize ST25TB Poller mode
+ *
+ * This methods configures RFAL RF layer to perform as a
+ * ST25TB Poller/RW including all default timings
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or mode not set
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerInitialize( SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Check Presence
+ *
+ * This method checks if a ST25TB Listen device (PICC) is present on the field
+ * by sending an Initiate command
+ *
+ * \param[out] chipId : if successfully retrieved, the device's chip ID
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_RF_COLLISION : Collision detected one or more device in the field
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCheckPresence( uint8_t *chipId, SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Collision Resolution
+ *
+ * This method performs ST25TB Collision resolution, selects the each device,
+ * retrieves its UID and then deselects.
+ * In case only one device is identified the ST25TB device is left in select
+ * state.
+ *
+ * \param[in] devLimit : device limit value, and size st25tbDevList
+ * \param[out] st25tbDevList : ST35TB listener device info
+ * \param[out] devCnt : Devices found counter
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_RF_COLLISION : Collision detected one or more device in the field
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCollisionResolution( uint8_t devLimit, rfalSt25tbListenDevice *st25tbDevList, uint8_t *devCnt,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Initiate
+ *
+ * This method sends an Initiate command
+ *
+ * If a single device responds the chip ID will be retrieved
+ *
+ * \param[out] chipId : chip ID of the device
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerInitiate( uint8_t *chipId,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Pcall
+ *
+ * This method sends a Pcall command
+ * If successful the device's chip ID will be retrieved
+ *
+ * \param[out] chipId : Chip ID of the device
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerPcall( uint8_t *chipId );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Slot Marker
+ *
+ * This method sends a Slot Marker
+ *
+ * If a single device responds the chip ID will be retrieved
+ *
+ * \param[in] slotNum : Slot Number
+ * \param[out] chipIdRes : Chip ID of the device
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerSlotMarker( uint8_t slotNum, uint8_t *chipIdRes,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Select
+ *
+ * This method sends a ST25TB Select command with the given chip ID.
+ *
+ * If the device is already in Selected state and receives an incorrect chip
+ * ID, it goes into Deselected state
+ *
+ * \param[in] chipId : chip ID of the device to be selected
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerSelect( uint8_t chipId,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Get UID
+ *
+ * This method sends a Get_UID command
+ *
+ * If a single device responds the chip UID will be retrieved
+ *
+ * \param[out] UID : UID of the found device
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerGetUID( rfalSt25tbUID *UID,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Read Block
+ *
+ * This method reads a block of the ST25TB
+ *
+ * \param[in] blockAddress : address of the block to be read
+ * \param[out] blockData : location to place the data read from block
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerReadBlock( uint8_t blockAddress, rfalSt25tbBlock *blockData,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Write Block
+ *
+ * This method writes a block of the ST25TB
+ *
+ * \param[in] blockAddress : address of the block to be written
+ * \param[in] blockData : data to be written on the block
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerWriteBlock( uint8_t blockAddress, rfalSt25tbBlock *blockData,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Completion
+ *
+ * This method sends a completion command to the ST25TB. After the
+ * completion the card no longer will reply to any command.
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected, invalid SENSB_RES received
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCompletion( SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief ST25TB Poller Reset to Inventory
+ *
+ * This method sends a Reset to Inventory command to the ST25TB.
+ *
+ * \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM : Invalid parameters
+ * \return ERR_IO : Generic internal error
+ * \return ERR_TIMEOUT : Timeout error, no listener device detected
+ * \return ERR_PROTO : Protocol error detected, invalid SENSB_RES received
+ * \return ERR_NONE : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerResetToInventory( SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+#endif /* RFAL_ST25TB_H */
+
+/**
+ * @}
+ *
+ * @}
+ *
+ * @}
+ */
+