Diff: rfal_st25tb.h

Revision:

0:75fc82583a41

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/rfal_st25tb.h	Thu Nov 14 14:34:50 2019 +0000
@@ -0,0 +1,355 @@
+
+/******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2016 STMicroelectronics</center></h2>
+  *
+  * Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
+  * You may not use this file except in compliance with the License.
+  * You may obtain a copy of the License at:
+  *
+  *        http://www.st.com/myliberty
+  *
+  * Unless required by applicable law or agreed to in writing, software
+  * distributed under the License is distributed on an "AS IS" BASIS,
+  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
+  * AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
+  * FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
+  * See the License for the specific language governing permissions and
+  * limitations under the License.
+  *
+******************************************************************************/
+
+/*
+ *      PROJECT:   ST25R391x firmware
+ *      $Revision: $
+ *      LANGUAGE:  ISO C99
+ */
+
+/*! \file rfal_st25tb.h
+ *
+ *  \author Gustavo Patricio
+ *
+ *  \brief Implementation of ST25TB interface
+ *
+ *
+ * @addtogroup RFAL
+ * @{
+ *
+ * @addtogroup RFAL-AL
+ * @brief RFAL Abstraction Layer
+ * @{
+ *
+ * @addtogroup ST25TB
+ * @brief RFAL ST25TB Module
+ * @{
+ *
+ */
+
+
+#ifndef RFAL_ST25TB_H
+#define RFAL_ST25TB_H
+
+/*
+ ******************************************************************************
+ * INCLUDES
+ ******************************************************************************
+ */
+#include "platform1.h"
+#include "st_errno.h"
+#include "rfal_rf.h"
+#include "rfal_nfcb.h"
+
+/*
+ ******************************************************************************
+ * GLOBAL DEFINES
+ ******************************************************************************
+ */
+
+#define RFAL_ST25TB_CHIP_ID_LEN      1       /*!< ST25TB chip ID length       */
+#define RFAL_ST25TB_CRC_LEN          2       /*!< ST25TB CRC length           */
+#define RFAL_ST25TB_UID_LEN          8       /*!< ST25TB Unique ID length     */
+#define RFAL_ST25TB_BLOCK_LEN        4       /*!< ST25TB Data Block length    */
+
+/*
+******************************************************************************
+* GLOBAL MACROS
+******************************************************************************
+*/
+
+
+
+/*
+******************************************************************************
+* GLOBAL TYPES
+******************************************************************************
+*/
+typedef uint8_t rfalSt25tbUID[RFAL_ST25TB_UID_LEN];        /*!< ST25TB UID type          */
+typedef uint8_t rfalSt25tbBlock[RFAL_ST25TB_BLOCK_LEN];    /*!< ST25TB Block type        */
+
+
+/*! ST25TB listener device (PICC) struct  */
+typedef struct
+{
+    uint8_t           chipID;                              /*!< Device's session Chip ID */
+    rfalSt25tbUID     UID;                                 /*!< Device's UID             */
+    bool              isDeselected;                        /*!< Device deselect flag     */
+}rfalSt25tbListenDevice;
+
+
+/*
+******************************************************************************
+* GLOBAL FUNCTION PROTOTYPES
+******************************************************************************
+*/
+
+/*!
+ *****************************************************************************
+ * \brief  Initialize ST25TB Poller mode
+ *
+ * This methods configures RFAL RF layer to perform as a
+ * ST25TB Poller/RW including all default timings
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or mode not set
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerInitialize( SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Check Presence
+ *
+ * This method checks if a ST25TB Listen device (PICC) is present on the field
+ * by sending an Initiate command
+ *
+ * \param[out] chipId : if successfully retrieved, the device's chip ID
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_RF_COLLISION : Collision detected one or more device in the field
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCheckPresence( uint8_t *chipId, SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Collision Resolution
+ *
+ * This method performs ST25TB Collision resolution, selects the each device,
+ * retrieves its UID and then deselects.
+ * In case only one device is identified the ST25TB device is left in select
+ * state.
+ *
+ * \param[in]  devLimit      : device limit value, and size st25tbDevList
+ * \param[out] st25tbDevList : ST35TB listener device info
+ * \param[out] devCnt        : Devices found counter
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_RF_COLLISION : Collision detected one or more device in the field
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCollisionResolution( uint8_t devLimit, rfalSt25tbListenDevice *st25tbDevList, uint8_t *devCnt,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Initiate
+ *
+ * This method sends an Initiate command
+ *
+ * If a single device responds the chip ID will be retrieved
+ *
+ * \param[out]  chipId      : chip ID of the device
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerInitiate( uint8_t *chipId,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Pcall
+ *
+ * This method sends a Pcall command
+ * If successful the device's chip ID will be retrieved
+ *
+ * \param[out]  chipId      : Chip ID of the device
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerPcall( uint8_t *chipId );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Slot Marker
+ *
+ * This method sends a Slot Marker
+ *
+ * If a single device responds the chip ID will be retrieved
+ *
+ * \param[in]  slotNum      : Slot Number
+ * \param[out]  chipIdRes   : Chip ID of the device
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerSlotMarker( uint8_t slotNum, uint8_t *chipIdRes,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Select
+ *
+ * This method sends a ST25TB Select command with the given chip ID.
+ *
+ * If the device is already in Selected state and receives an incorrect chip
+ * ID, it goes into Deselected state
+ *
+ * \param[in]  chipId       : chip ID of the device to be selected
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerSelect( uint8_t chipId,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Get UID
+ *
+ * This method sends a Get_UID command
+ *
+ * If a single device responds the chip UID will be retrieved
+ *
+ * \param[out]  UID      : UID of the found device
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerGetUID( rfalSt25tbUID *UID,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Read Block
+ *
+ * This method reads a block of the ST25TB
+ *
+ * \param[in]   blockAddress : address of the block to be read
+ * \param[out]  blockData    : location to place the data read from block
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerReadBlock( uint8_t blockAddress, rfalSt25tbBlock *blockData,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Write Block
+ *
+ * This method writes a block of the ST25TB
+ *
+ * \param[in]  blockAddress : address of the block to be written
+ * \param[in]  blockData    : data to be written on the block
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerWriteBlock( uint8_t blockAddress, rfalSt25tbBlock *blockData,SPI* mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Completion
+ *
+ * This method sends a completion command to the ST25TB. After the
+ * completion the card no longer will reply to any command.
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected, invalid SENSB_RES received
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerCompletion( SPI*  mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+/*!
+ *****************************************************************************
+ * \brief  ST25TB Poller Reset to Inventory
+ *
+ * This method sends a Reset to Inventory command to the ST25TB.
+ *
+ * \return ERR_WRONG_STATE  : RFAL not initialized or incorrect mode
+ * \return ERR_PARAM        : Invalid parameters
+ * \return ERR_IO           : Generic internal error
+ * \return ERR_TIMEOUT      : Timeout error, no listener device detected
+ * \return ERR_PROTO        : Protocol error detected, invalid SENSB_RES received
+ * \return ERR_NONE         : No error
+ *****************************************************************************
+ */
+ReturnCode rfalSt25tbPollerResetToInventory( SPI*  mspiChannel, ST25R3911* mST25, DigitalOut* gpio_cs, InterruptIn* IRQ, DigitalOut* fieldLED_01, DigitalOut* fieldLED_02, DigitalOut* fieldLED_03, DigitalOut* fieldLED_04, DigitalOut* fieldLED_05, DigitalOut* fieldLED_06 );
+
+
+#endif /* RFAL_ST25TB_H */
+
+/**
+  * @}
+  *
+  * @}
+  *
+  * @}
+  */
+