File content as of revision 0:c23e915f255b:

#include "mbed.h"
#include "encoder.h"
#include "Mx28.h"
#include "PID.h"

//********************* Dynamxiel ******************************
#define SERVO_ID 0x01               // ID of which we will set Dynamixel too 
#define SERVO_ControlPin A2       // Control pin of buffer chip, NOTE: this does not matter becasue we are not using a half to full contorl buffer.
#define SERVO_SET_Baudrate 1000000  // Baud rate speed which the Dynamixel will be set too (1Mbps)
#define TxPin A0
#define RxPin A1
#define CW_LIMIT_ANGLE 1        // lowest clockwise angle is 1, as when set to 0 it set servo to wheel mode
#define CCW_LIMIT_ANGLE 4095       // Highest anit-clockwise angle is 0XFFF, as when set to 0 it set servo to wheel mode
#define PI 3.14159265f
//***************************************************************

Serial uart(USBTX, USBRX);
//Serial uart(D10,D2);            // TX : D10     RX : D2           // blueteeth
DigitalOut LED(A4);            // check if the code is running
DigitalOut led2(A5);            // check if the code is running interrupt
uint8_t led2f;

// Timer
Ticker timer1;
float ITR_time1 = 10000.0;  // unit：us
float Ts = ITR_time1/1000000;
uint8_t flag;

// uart_tx
union splitter {
    short j;
    char C[2];
    // C[0] is lowbyte of j, C[1] is highbyte of j
};
char T[16] = {255,255,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
int i = 0;

// PID
PID motor_pid(7.2, 0, 0.13, Ts);// 6.4 0.13   7.2 0.13
float PIDout = 0.0f;

// Dynamixel
DynamixelClass dynamixelClass(SERVO_SET_Baudrate,SERVO_ControlPin,TxPin,RxPin);
int servo_cmd;
int D_angle = 0;
int D_angle_dif = 0;
int D_Angle;
int D_angle_old;
unsigned short d = 0;
// Find Torque
double angle_difference = 0.0;
float torque_measured = 0.0;
float ks = 2.6393*2;  //spring constant
//int angle_dif = 0;
float torque_ref = 0.0;
float friction = 0.18f;
float rate = 0.8;
//float friction = 0.0f;
//float check = 0.0f;

// function
void init_UART();
void init_TIMER();
void timer1_ITR();
void uart_tx();

void init_DYNAMIXEL();
void D_angle_measure();
void find_torque();

int main()
{
    LED = 1; // darken
    wait_ms(500);
    // initial sensor
    init_SPI_encoder();
    init_encoder();
    init_DYNAMIXEL();
    // initial uart
    init_UART();

    wait_ms(500);

    led2 = 1;
    led2f = 0;
    LED = 0; // lighten

    init_TIMER();

    while(1) {
        if (flag==1) {
            led2 = !led2;
            angle_measure();
            D_angle_measure();
            find_torque();
            motor_pid.Compute(torque_ref, torque_measured);
            PIDout = motor_pid.output;
            servo_cmd = PIDout*121.8f;   // 1023/8.4Nm = 121.7857

            if (servo_cmd > 0) {
                servo_cmd = servo_cmd + ((-torque_ref)*rate+friction)*121.8f;
                if (servo_cmd >= 1023)
                    servo_cmd = 1023;
            } else {
                servo_cmd = -servo_cmd + 1024 + ((torque_ref)*rate+friction)*121.8f;
                if (servo_cmd >= 2047)
                    servo_cmd = 2047;
            }
//    dynamixelClass.torque(SERVO_ID, servo_cmd);
            uart_tx();
            flag = 0;
        }
    }
}

void init_DYNAMIXEL()
{
    dynamixelClass.torqueMode(SERVO_ID, 1);
    wait_ms(1);
}

void init_UART()
{
    uart.baud(115200);
}

void init_TIMER()
{
    timer1.attach_us(&timer1_ITR, ITR_time1);
}

void timer1_ITR()
{
    flag = 1;
    if (led2f == 5) {

        led2f = 0;
    } else {
        led2f++;
    }
}

void uart_tx()
{
    splitter s1;
    splitter s2;
    splitter s3;
    splitter s4;
    splitter s5;
    splitter s6;
    splitter s7;

    s1.j = angle;
    s2.j = Angle;
    s3.j = 2;
//    s4.j = 1;
//    s5.j = 3;
    s4.j = D_angle;
    s5.j = D_Angle;
    s6.j = torque_measured*1000;
    s7.j = 3;

    T[2] = s1.C[0];
    T[3] = s1.C[1];
    T[4] = s2.C[0];
    T[5] = s2.C[1];
    T[6] = s3.C[0];
    T[7] = s3.C[1];
    T[8] = s4.C[0];
    T[9] = s4.C[1];
    T[10] = s5.C[0];
    T[11] = s5.C[1];
    T[12] = s6.C[0];
    T[13] = s6.C[1];
    T[14] = s7.C[0];
    T[15] = s7.C[1];

    while(1) {
        if (uart.writeable() == 1) {
            uart.putc(T[i]);
            i++;
        }
        if (i >= (sizeof(T)-1)) {
            i = 0;
            break;
        }
    }
}

void D_angle_measure()
{
    D_angle = dynamixelClass.readPosition(SERVO_ID);

    if (d == 0) {
        D_Angle = 0;
        D_angle_old = D_angle;
        d++;
    } else {
        D_angle_dif = D_angle - D_angle_old;
        D_Angle = D_Angle + D_angle_dif;
        D_angle_old = D_angle;
    }
}

void find_torque()
{
    angle_difference = (Angle*3-D_Angle)/4096.0f*2*PI;
    torque_measured = angle_difference*ks;
}