display funciona!
Dependents: 2018_I2C_LCD_03 TBI_FIAT_FEEDFORWARD Ignition Can_between_NUCLEOS_LCD ... more
Fork of TextLCD by
Diff: TextLCD.cpp
- Revision:
- 24:fb3399713710
- Parent:
- 23:d47f226efb24
- Child:
- 25:6162b31128c9
--- a/TextLCD.cpp Wed Apr 02 18:16:37 2014 +0000 +++ b/TextLCD.cpp Sat May 10 13:50:25 2014 +0000 @@ -111,7 +111,18 @@ wait_ms(50); break; - + case ST7032: + _writeByte( 0x1c ); //Internal OSC frequency adjustment 183HZ bias will be 1/4 + wait_us(30); + _writeByte( 0x73 ); //Contrast control low byte + wait_us(30); + _writeByte( 0x57 ); //booster circuit is turn on. /ICON display off. /Contrast control high byte + wait_us(30); + _writeByte( 0x6c ); //Follower control + wait_us(50); + _writeByte( 0x0c ); //DISPLAY ON + wait_us(30); + break; case WS0010: // WS0010 OLED controller: Initialise DC/DC Voltage converter for LEDs // Note: supports 1 or 2 lines (and 16x100 graphics) @@ -1107,6 +1118,77 @@ //---------- End TextLCD_SPI ------------ +//--------- Start TextLCD_NativeSPI ----------- + + /** Create a TextLCD interface using an SPI 74595 portexpander + * + * @param spi SPI Bus + * @param cs chip select pin (active low) + * @param type Sets the panel size/addressing mode (default = LCD16x2) + * @param ctrl LCD controller (default = HD44780) + */ +TextLCD_NativeSPI::TextLCD_NativeSPI(SPI *spi, PinName cs, PinName rs, LCDType type, PinName bl, LCDCtrl ctrl) : + TextLCD_Base(type, ctrl), + _spi(spi), + _cs(cs), + _rs(rs) { + + // Setup the spi for 8 bit data, low steady state clock, + // rising edge capture, with a 500KHz or 1MHz clock rate + _spi->format(8,0); + _spi->frequency(1000000); + + // The hardware Backlight pin is optional. Test and make sure whether it exists or not to prevent illegal access. + if (bl != NC) { + _bl = new DigitalOut(bl); //Construct new pin + _bl->write(0); //Deactivate + } + else { + // No Hardware Backlight pin + _bl = NULL; //Construct dummy pin + } + + _writeByte( 0x39 ); //FUNCTION SET 8 bit,N=1 2-line display mode,5*7dot IS=1 + wait_us(30); + _init(); +} + +TextLCD_NativeSPI::~TextLCD_NativeSPI() { + if (_bl != NULL) {delete _bl;} // BL pin +} + +// Not used in this mode +void TextLCD_NativeSPI::_setEnable(bool value) { +} + +// Set RS pin +// Used for mbed pins, I2C bus expander or SPI shiftregister +void TextLCD_NativeSPI::_setRS(bool value) { + _rs = value; +} + +// Set BL pin +void TextLCD_NativeSPI::_setBL(bool value) { + if (_bl) + _bl->write(value); +} + +// Write a byte using SPI +void TextLCD_NativeSPI::_writeByte(int value) { + _cs = 0; + wait_us(1); + _spi->write(value); + wait_us(1); + _cs = 1; +} + + +// Not used in this mode +void TextLCD_NativeSPI::_setData(int value) { +} + + +//---------- End TextLCD_NativeSPI ------------