You are viewing an older revision! See the latest version
STM32 Nucleo ATT Hackathon
AT&T CTIA Connected Car and Connected Home Hackathon¶
ST is proud to be a part of Team mBed™ at the AT&T Hackathon at Super Mobility Week - Code for Car and Home. Join us at the event in Las Vegas by registering now for your free ticket! And if you are going to be a part of the Hackathon, read up on ST’s microcontrollers beforehand here to increase your chances at the $10k grand prize.
Tutorials¶
Tutorial #1: Preparing the STM32F411 Nucleo Board for Development with ARM mbed
Tutorial #2: Getting Started with mbed and the STM32F411 Nucleo Board
STM32F411 Nucleo Information¶
The STM32 Nucleo board is a low-cost and easy-to-use development platform used to quickly evaluate and start a development with an STM32 microcontroller in LQFP64 package.
- All mbed information for this board can be found here:
mbed ST Nucleo F411RE Platform Page - A complete description of the features of this board, including schematics is found here:
STM32F411 Nucleo User Manual - Additional information on the STM32F411 Nucleo board can be found here:
STM32F411 Nucleo Home page
STM32F411 Microcontroller Information¶
The STM32F411XC/XE family is based on the high-performance ARM Cortex-M4 32-bit RISC core operating at a frequency of up to 100 MHz. Its Cortex-M4 with FPU core features a Floating point unit (FPU) single precision which supports all ARM single-precision data-processing instructions and data types. It also implements a full set of DSP instructions and a memory protection unit (MPU) which enhances application security.
- Download the datasheet here:
STM32F411 Datasheet - Download the reference manual here:
STM32F411 Flash Programming Manual - Addition information, including application notes, programming manual, tools and software can be found here:
STM32F411 Home Page
ST-Link Utilities¶
ST-Link is the USB device interface that allows the STM32 Nucleo to be programmed by mbed.
It is recommended that you pre-install the ST-Link PC driver and update the ST-Link firmware before using your STM32 Nucleo with mbed.
ST-Link PC Firmware (V2.J22.M5)
ST-Link PC Driver
ST-Link/V2 is a software utilities that allows you to connect to the STM32 microcontroller on the Nucleo board. It allows you to read and write the embedded flash contents of the STM32.
STM32 ST-Link Software Utility
STM32 ST-Link Software Description
WiFi Connectivity Modules¶
- Multi-tech WiFly Module
mbed Multi-tech Wifly Sample Application
Sensors¶
Seeed Studio Sensor Information
Use the Grove Shield board to connect to the STM32 Nucleo Arduino connector. The provides the base for connected other Grove sensor modules
- Grove Arduino Shield Board
Grove Shield
- Grove Sensors
Grove Temp / Humidity
Grove HCHO
Grove Barometer
Grove Digital Light
Grove Analog Light
Grove Air Quality
Grove Digital Compass
Grove Collision Sensor
Grove Gyro
Grove Accelerometer
Grove Water Sensor
Grove Alcohol Sensor
Grove Electricity Sensor
Grove Moisture Sensor
Grove Motion Sensor
Grove UV Sensor
Grove Heart Rate sensor
Grove Chest Strap Heart Rate Sensor
- Grove Connectivity Modules
Grove Xbee / Wifi Adapter
Grove Simple RF Link 433Mhz
Grove Serial RF Pro
Grove Simple RF Link 333Mhz
Grove Serial Bluetooth
- Grove User Interface
Grove Button
Grove Vibration Motor
Grove LED Bar
Grove Relay
Grove Proto Board
Grove Joystick
Grove 4-Digit Display
Grove Slider
Grove Touch Sensor (Multiple)
Grove Buzzer
Grove Touch Sensor (Single)
- Grove Connector Cables
Grove Buckled 40cm Cable
Grove 4 pin Conversion Cable
Grove 20cm Unbuckled Cable
AT&T M2X¶
AT&T M2X is a fully managed data storage service for internet connected machine-to-machine devices that leverages the power and scale of AT&T's global network.
How-to Videos:¶
- Getting Starting With your Nucleo Board
- Getting started with mbed
- Run your first program "hello world"
- Getting started wit a WiFi module
- Getting started with sensors
- Getting started with AT&T M2X
- From device to cloud