Digi International Inc. / Mbed 2 deprecated XBeeDM_dio_adc_pwm

DigiMEsh DIOs, ADCs and PWMs example for mbed XBeeLib By Digi

Dependencies:   XBeeLib mbed

Fork of XBeeZB_dio_adc by Digi International Inc.

This example shows how to handle remote XBee modules DigitalInputOutputs, ADCs and PWMs. The example configures the remote XBee module pins to the desired functionality and then operates on those pins.

See Handling remote modules DIOs ADCs and PWMs chapter for more information.

Common Setup

Make sure you have a valid Example Common Setup

Example Setup

Application

You have to configure the remote device 64-bit address by customizing the REMOTE_NODE_ADDR64_MSB and REMOTE_NODE_ADDR64_LSB defines with the remote XBee module 64-bit address.

Hardware

On the Remote XBee module, wire following peripherals to the pins specified on the table and schematics or change the application pins according to your hardware setup:

LinePinValue
DIO2/ADC218ADC (Analog Input)
DIO3/ADC317Digital Input
RSSI/DIO106PWM (Analog Output)
DIO411Digital Output

/media/uploads/hbujanda/dio_adc_schem.png

Running the example

Build and deploy the example to the mbed module.
Reset the mbed module so the example starts. You should see the example debug information through the debug interface configured in the 'Local Setup' chapter.
The application will do following operations:

  • Configure the remote XBee module pins according to the table above.
  • Do following loop every 5 seconds:
    • Read DIO3_AD3 digital value
    • Toggle LED associated to DIO4_AD4
    • Read DIO2_AD2 analog value
    • Set the led associated to PWM0 to different intensity levels

main.cpp

Committer:
hbujanda
Date:
2016-07-29
Revision:
11:5de2aa212c22
Parent:
10:6d9a4f4a3740

File content as of revision 11:5de2aa212c22:

/**
 * Copyright (c) 2015 Digi International Inc.,
 * All rights not expressly granted are reserved.
 *
 * This Source Code Form is subject to the terms of the Mozilla Public
 * License, v. 2.0. If a copy of the MPL was not distributed with this file,
 * You can obtain one at http://mozilla.org/MPL/2.0/.
 *
 * Digi International Inc. 11001 Bren Road East, Minnetonka, MN 55343
 * =======================================================================
 */

#include "mbed.h"
#include "XBeeLib.h"
#if defined(ENABLE_LOGGING)
#include "DigiLoggerMbedSerial.h"
using namespace DigiLog;
#endif

#define REMOTE_NODE_ADDR64_MSB  ((uint32_t)0x0013A200)

#error "Replace next define with the LSB of the remote module's 64-bit address (SL parameter)"
#define REMOTE_NODE_ADDR64_LSB  ((uint32_t)0x01234567)

#define REMOTE_NODE_ADDR64      UINT64(REMOTE_NODE_ADDR64_MSB, REMOTE_NODE_ADDR64_LSB)

using namespace XBeeLib;

Serial *log_serial;

int main()
{
    log_serial = new Serial(DEBUG_TX, DEBUG_RX);
    log_serial->baud(9600);
    log_serial->printf("Sample application to demo how to handle remote XBeeDM devices DIOs and ADCs\r\n\r\n");
    log_serial->printf(XB_LIB_BANNER);

#if defined(ENABLE_LOGGING)
    new DigiLoggerMbedSerial(log_serial, LogLevelInfo);
#endif

    XBeeDM xbee = XBeeDM(RADIO_TX, RADIO_RX, RADIO_RESET, NC, NC, 9600);

    RadioStatus radioStatus = xbee.init();
    MBED_ASSERT(radioStatus == Success);

    const RemoteXBeeDM remoteDevice = RemoteXBeeDM(REMOTE_NODE_ADDR64);

    radioStatus = xbee.set_pin_config(remoteDevice, XBeeDM::DIO3_AD3, DigitalInput);
    MBED_ASSERT(radioStatus == Success);

    radioStatus = xbee.set_pin_pull_up(remoteDevice, XBeeDM::DIO3_AD3, true);
    MBED_ASSERT(radioStatus == Success);

    radioStatus = xbee.set_pin_config(remoteDevice, XBeeDM::DIO4, DigitalOutHigh);
    MBED_ASSERT(radioStatus == Success);

    radioStatus = xbee.set_pin_config(remoteDevice, XBeeDM::DIO2_AD2, Adc);
    MBED_ASSERT(radioStatus == Success);

    radioStatus = xbee.set_pin_config(remoteDevice, XBeeDM::DIO10_PWM0, Pwm);
    MBED_ASSERT(radioStatus == Success);

    while(true) {
        IOSampleDM ioSample = xbee.get_iosample(remoteDevice);

        if (!ioSample.is_valid()) {
            log_serial->printf("get_iosample failed, ADC and Digital Input reads will be invalid\r\n");
        }
        /* Read DIO3_AD3 digital value */
        DioVal dio3_val;

        radioStatus = ioSample.get_dio(XBeeDM::DIO3_AD3, &dio3_val);
        MBED_ASSERT(radioStatus == Success);
        log_serial->printf("DIO3 value = %d\r\n", dio3_val);

        /* Toggle LED associated to DIO4 */
        static bool led_on = false;
        if (!led_on)
            radioStatus = xbee.set_dio(remoteDevice, XBeeDM::DIO4, Low);
        else
            radioStatus = xbee.set_dio(remoteDevice, XBeeDM::DIO4, High);
        MBED_ASSERT(radioStatus == Success);
        led_on = !led_on;

        /* Read DIO2_AD2 analog value */
        uint16_t adc2_val;
        radioStatus = ioSample.get_adc(XBeeDM::DIO2_AD2, &adc2_val);
        MBED_ASSERT(radioStatus == Success);
        log_serial->printf("ADC2 value = 0x%04x\r\n", adc2_val);

        /* Set the led associated to PWM0 to different intensity levels */
        static float pwm_val_list[] = { 0.0, 50.0, 70.0, 100.0 };
        static uint8_t pwm_val_idx = 0;
        log_serial->printf("Setting PWM0 to = %f\r\n", pwm_val_list[pwm_val_idx]);
        radioStatus = xbee.set_pwm(remoteDevice, XBeeDM::DIO10_PWM0, pwm_val_list[pwm_val_idx]);
        MBED_ASSERT(radioStatus == Success);
        pwm_val_idx++;
        if (pwm_val_idx == sizeof(pwm_val_list)/sizeof(pwm_val_list[0])) {
            pwm_val_idx = 0;
        }

        log_serial->printf("\r\n");

        wait(5);
    }

    delete(log_serial);
}