Mouse code for the MacroRat
mbed-dev/targets/TARGET_Atmel/TARGET_SAM_CortexM4/drivers/usart/usart.c
- Committer:
- sahilmgandhi
- Date:
- 2017-06-03
- Revision:
- 46:b156ef445742
- Parent:
- 18:6a4db94011d3
File content as of revision 46:b156ef445742:
/** * \file * * \brief Universal Synchronous Asynchronous Receiver Transmitter (USART) driver * for SAM. * * Copyright (c) 2011-2015 Atmel Corporation. All rights reserved. * * \asf_license_start * * \page License * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * * 3. The name of Atmel may not be used to endorse or promote products derived * from this software without specific prior written permission. * * 4. This software may only be redistributed and used in connection with an * Atmel microcontroller product. * * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * \asf_license_stop * */ /* * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a> */ #include "usart.h" /// @cond 0 /**INDENT-OFF**/ #ifdef __cplusplus extern "C" { #endif /**INDENT-ON**/ /// @endcond /** * \defgroup sam_drivers_usart_group Universal Synchronous Asynchronous * Receiver Transmitter (USART) * * The Universal Synchronous Asynchronous Receiver Transceiver (USART) * provides one full duplex universal synchronous asynchronous serial link. * Data frame format is widely programmable (data length, parity, number of * stop bits) to support a maximum of standards. The receiver implements * parity error, framing error and overrun error detection. The receiver * time-out enables handling variable-length frames and the transmitter * timeguard facilitates communications with slow remote devices. Multidrop * communications are also supported through address bit handling in reception * and transmission. The driver supports the following modes: * RS232, RS485, SPI, IrDA, ISO7816, MODEM, Hardware handshaking and LIN. * * @{ */ /* The write protect key value. */ #ifndef US_WPMR_WPKEY_PASSWD #define US_WPMR_WPKEY_PASSWD US_WPMR_WPKEY(0x555341U) #endif #ifndef US_WPMR_WPKEY_PASSWD # define US_WPMR_WPKEY_PASSWD US_WPMR_WPKEY(US_WPKEY_VALUE) #endif /* The CD value scope programmed in MR register. */ #define MIN_CD_VALUE 0x01 #define MIN_CD_VALUE_SPI 0x04 #define MAX_CD_VALUE US_BRGR_CD_Msk /* The receiver sampling divide of baudrate clock. */ #define HIGH_FRQ_SAMPLE_DIV 16 #define LOW_FRQ_SAMPLE_DIV 8 /* Max transmitter timeguard. */ #define MAX_TRAN_GUARD_TIME US_TTGR_TG_Msk /* The non-existent parity error number. */ #define USART_PARITY_ERROR 5 /* ISO7816 protocol type. */ #define ISO7816_T_0 0 #define ISO7816_T_1 1 /** * \brief Calculate a clock divider(CD) and a fractional part (FP) for the * USART asynchronous modes to generate a baudrate as close as possible to * the baudrate set point. * * \note Baud rate calculation: Baudrate = ul_mck/(Over * (CD + FP/8)) * (Over being 16 or 8). The maximal oversampling is selected if it allows to * generate a baudrate close to the set point. * * \param p_usart Pointer to a USART instance. * \param baudrate Baud rate set point. * \param ul_mck USART module input clock frequency. * * \retval 0 Baud rate is successfully initialized. * \retval 1 Baud rate set point is out of range for the given input clock * frequency. */ uint32_t usart_set_async_baudrate(Usart *p_usart, uint32_t baudrate, uint32_t ul_mck) { uint32_t over; uint32_t cd_fp; uint32_t cd; uint32_t fp; /* Calculate the receiver sampling divide of baudrate clock. */ if (ul_mck >= HIGH_FRQ_SAMPLE_DIV * baudrate) { over = HIGH_FRQ_SAMPLE_DIV; } else { over = LOW_FRQ_SAMPLE_DIV; } /* Calculate clock divider according to the fraction calculated formula. */ cd_fp = (8 * ul_mck + (over * baudrate) / 2) / (over * baudrate); cd = cd_fp >> 3; fp = cd_fp & 0x07; if (cd < MIN_CD_VALUE || cd > MAX_CD_VALUE) { return 1; } /* Configure the OVER bit in MR register. */ if (over == 8) { p_usart->US_MR |= US_MR_OVER; } /* Configure the baudrate generate register. */ p_usart->US_BRGR = (cd << US_BRGR_CD_Pos) | (fp << US_BRGR_FP_Pos); return 0; } /** * \brief Calculate a clock divider for the USART synchronous master modes * to generate a baudrate as close as possible to the baudrate set point. * * \note Synchronous baudrate calculation: baudrate = ul_mck / cd * * \param p_usart Pointer to a USART instance. * \param baudrate Baud rate set point. * \param ul_mck USART module input clock frequency. * * \retval 0 Baud rate is successfully initialized. * \retval 1 Baud rate set point is out of range for the given input clock * frequency. */ static uint32_t usart_set_sync_master_baudrate(Usart *p_usart, uint32_t baudrate, uint32_t ul_mck) { uint32_t cd; /* Calculate clock divider according to the formula in synchronous mode. */ cd = (ul_mck + baudrate / 2) / baudrate; if (cd < MIN_CD_VALUE || cd > MAX_CD_VALUE) { return 1; } /* Configure the baudrate generate register. */ p_usart->US_BRGR = cd << US_BRGR_CD_Pos; p_usart->US_MR = (p_usart->US_MR & ~US_MR_USCLKS_Msk) | US_MR_USCLKS_MCK | US_MR_SYNC; return 0; } /** * \brief Select the SCK pin as the source of baud rate for the USART * synchronous slave modes. * * \param p_usart Pointer to a USART instance. */ static void usart_set_sync_slave_baudrate(Usart *p_usart) { p_usart->US_MR = (p_usart->US_MR & ~US_MR_USCLKS_Msk) | US_MR_USCLKS_SCK | US_MR_SYNC; } /** * \brief Calculate a clock divider (\e CD) for the USART SPI master mode to * generate a baud rate as close as possible to the baud rate set point. * * \note Baud rate calculation: * \f$ Baudrate = \frac{SelectedClock}{CD} \f$. * * \param p_usart Pointer to a USART instance. * \param baudrate Baud rate set point. * \param ul_mck USART module input clock frequency. * * \retval 0 Baud rate is successfully initialized. * \retval 1 Baud rate set point is out of range for the given input clock * frequency. */ static uint32_t usart_set_spi_master_baudrate(Usart *p_usart, uint32_t baudrate, uint32_t ul_mck) { uint32_t cd; /* Calculate the clock divider according to the formula in SPI mode. */ cd = (ul_mck + baudrate / 2) / baudrate; if (cd < MIN_CD_VALUE_SPI || cd > MAX_CD_VALUE) { return 1; } p_usart->US_BRGR = cd << US_BRGR_CD_Pos; return 0; } /** * \brief Select the SCK pin as the source of baudrate for the USART SPI slave * mode. * * \param p_usart Pointer to a USART instance. */ static void usart_set_spi_slave_baudrate(Usart *p_usart) { p_usart->US_MR &= ~US_MR_USCLKS_Msk; p_usart->US_MR |= US_MR_USCLKS_SCK; } /** * \brief Reset the USART and disable TX and RX. * * \param p_usart Pointer to a USART instance. */ void usart_reset(Usart *p_usart) { /* Disable the Write Protect. */ usart_disable_writeprotect(p_usart); /* Reset registers that could cause unpredictable behavior after reset. */ p_usart->US_MR = 0; p_usart->US_RTOR = 0; p_usart->US_TTGR = 0; /* Disable TX and RX. */ usart_reset_tx(p_usart); usart_reset_rx(p_usart); /* Reset status bits. */ usart_reset_status(p_usart); /* Turn off RTS and DTR if exist. */ usart_drive_RTS_pin_high(p_usart); #if (SAM3S || SAM4S || SAM3U || SAM4L || SAM4E) usart_drive_DTR_pin_high(p_usart); #endif } /** * \brief Configure USART to work in RS232 mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_rs232(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; /* Check whether the input values are legal. */ if (!p_usart_opt || usart_set_async_baudrate(p_usart, p_usart_opt->baudrate, ul_mck)) { return 1; } /* Configure the USART option. */ ul_reg_val |= p_usart_opt->char_length | p_usart_opt->parity_type | p_usart_opt->channel_mode | p_usart_opt->stop_bits; /* Configure the USART mode as normal mode. */ ul_reg_val |= US_MR_USART_MODE_NORMAL; p_usart->US_MR |= ul_reg_val; return 0; } /** * \brief Configure USART to work in hardware handshaking mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_hw_handshaking(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { /* Initialize the USART as standard RS232. */ if (usart_init_rs232(p_usart, p_usart_opt, ul_mck)) { return 1; } /* Set hardware handshaking mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_HW_HANDSHAKING; return 0; } #if (SAM3S || SAM4S || SAM3U || SAM4L || SAM4E) /** * \brief Configure USART to work in modem mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_modem(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { /* * SAM3S, SAM4S and SAM4E series support MODEM mode only on USART1, * SAM3U and SAM4L series support MODEM mode only on USART0. */ #if (SAM3S || SAM4S || SAM4E) #ifdef USART1 if (p_usart != USART1) { return 1; } #endif #elif (SAM3U || SAM4L) if (p_usart != USART0) { return 1; } #endif /* Initialize the USART as standard RS232. */ if (usart_init_rs232(p_usart, p_usart_opt, ul_mck)) { return 1; } /* Set MODEM mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_MODEM; return 0; } #endif /** * \brief Configure USART to work in SYNC mode and act as a master. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_sync_master(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; /* Check whether the input values are legal. */ if (!p_usart_opt || usart_set_sync_master_baudrate(p_usart, p_usart_opt->baudrate, ul_mck)) { return 1; } /* Configure the USART option. */ ul_reg_val |= p_usart_opt->char_length | p_usart_opt->parity_type | p_usart_opt->channel_mode | p_usart_opt->stop_bits; /* Set normal mode and output clock as synchronous master. */ ul_reg_val |= US_MR_USART_MODE_NORMAL | US_MR_CLKO; p_usart->US_MR |= ul_reg_val; return 0; } /** * \brief Configure USART to work in SYNC mode and act as a slave. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_sync_slave(Usart *p_usart, const sam_usart_opt_t *p_usart_opt) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; usart_set_sync_slave_baudrate(p_usart); /* Check whether the input values are legal. */ if (!p_usart_opt) { return 1; } /* Configure the USART option. */ ul_reg_val |= p_usart_opt->char_length | p_usart_opt->parity_type | p_usart_opt->channel_mode | p_usart_opt->stop_bits; /* Set normal mode. */ ul_reg_val |= US_MR_USART_MODE_NORMAL; p_usart->US_MR |= ul_reg_val; return 0; } /** * \brief Configure USART to work in RS485 mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_rs485(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { /* Initialize the USART as standard RS232. */ if (usart_init_rs232(p_usart, p_usart_opt, ul_mck)) { return 1; } /* Set RS485 mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_RS485; return 0; } #if (!SAMG55 && !SAMV71 && !SAMV70 && !SAME70 && !SAMS70) /** * \brief Configure USART to work in IrDA mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_irda(Usart *p_usart, const sam_usart_opt_t *p_usart_opt, uint32_t ul_mck) { /* Initialize the USART as standard RS232. */ if (usart_init_rs232(p_usart, p_usart_opt, ul_mck)) { return 1; } /* Set IrDA filter. */ p_usart->US_IF = p_usart_opt->irda_filter; /* Set IrDA mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_IRDA; return 0; } #endif #if (!SAMV71 && !SAMV70 && !SAME70 && !SAMS70) /** * \brief Calculate a clock divider (\e CD) for the USART ISO7816 mode to * generate an ISO7816 clock as close as possible to the clock set point. * * \note ISO7816 clock calculation: Clock = ul_mck / cd * * \param p_usart Pointer to a USART instance. * \param clock ISO7816 clock set point. * \param ul_mck USART module input clock frequency. * * \retval 0 ISO7816 clock is successfully initialized. * \retval 1 ISO7816 clock set point is out of range for the given input clock * frequency. */ static uint32_t usart_set_iso7816_clock(Usart *p_usart, uint32_t clock, uint32_t ul_mck) { uint32_t cd; /* Calculate clock divider according to the formula in ISO7816 mode. */ cd = (ul_mck + clock / 2) / clock; if (cd < MIN_CD_VALUE || cd > MAX_CD_VALUE) { return 1; } p_usart->US_MR = (p_usart->US_MR & ~(US_MR_USCLKS_Msk | US_MR_SYNC | US_MR_OVER)) | US_MR_USCLKS_MCK | US_MR_CLKO; /* Configure the baudrate generate register. */ p_usart->US_BRGR = cd << US_BRGR_CD_Pos; return 0; } /** * \brief Configure USART to work in ISO7816 mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_iso7816(Usart *p_usart, const usart_iso7816_opt_t *p_usart_opt, uint32_t ul_mck) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; /* Check whether the input values are legal. */ if (!p_usart_opt || ((p_usart_opt->parity_type != US_MR_PAR_EVEN) && (p_usart_opt->parity_type != US_MR_PAR_ODD))) { return 1; } if (p_usart_opt->protocol_type == ISO7816_T_0) { ul_reg_val |= US_MR_USART_MODE_IS07816_T_0 | US_MR_NBSTOP_2_BIT | (p_usart_opt->max_iterations << US_MR_MAX_ITERATION_Pos); if (p_usart_opt->bit_order) { ul_reg_val |= US_MR_MSBF; } } else if (p_usart_opt->protocol_type == ISO7816_T_1) { /* * Only LSBF is used in the T=1 protocol, and max_iterations field * is only used in T=0 mode. */ if (p_usart_opt->bit_order || p_usart_opt->max_iterations) { return 1; } /* Set USART mode to ISO7816, T=1, and always uses 1 stop bit. */ ul_reg_val |= US_MR_USART_MODE_IS07816_T_1 | US_MR_NBSTOP_1_BIT; } else { return 1; } /* Set up the baudrate. */ if (usart_set_iso7816_clock(p_usart, p_usart_opt->iso7816_hz, ul_mck)) { return 1; } /* Set FIDI register: bit rate = iso7816_hz / fidi_ratio. */ p_usart->US_FIDI = p_usart_opt->fidi_ratio; /* Set ISO7816 parity type in the MODE register. */ ul_reg_val |= p_usart_opt->parity_type; if (p_usart_opt->inhibit_nack) { ul_reg_val |= US_MR_INACK; } if (p_usart_opt->dis_suc_nack) { ul_reg_val |= US_MR_DSNACK; } p_usart->US_MR |= ul_reg_val; return 0; } /** * \brief Reset the ITERATION in US_CSR when the ISO7816 mode is enabled. * * \param p_usart Pointer to a USART instance. */ void usart_reset_iterations(Usart *p_usart) { p_usart->US_CR = US_CR_RSTIT; } /** * \brief Reset NACK in US_CSR. * * \param p_usart Pointer to a USART instance. */ void usart_reset_nack(Usart *p_usart) { p_usart->US_CR = US_CR_RSTNACK; } /** * \brief Check if one receive buffer is filled. * * \param p_usart Pointer to a USART instance. * * \retval 1 Receive is complete. * \retval 0 Receive is still pending. */ uint32_t usart_is_rx_buf_end(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_ENDRX) > 0; } /** * \brief Check if one transmit buffer is empty. * * \param p_usart Pointer to a USART instance. * * \retval 1 Transmit is complete. * \retval 0 Transmit is still pending. */ uint32_t usart_is_tx_buf_end(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_ENDTX) > 0; } /** * \brief Check if both receive buffers are full. * * \param p_usart Pointer to a USART instance. * * \retval 1 Receive buffers are full. * \retval 0 Receive buffers are not full. */ uint32_t usart_is_rx_buf_full(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_RXBUFF) > 0; } /** * \brief Check if both transmit buffers are empty. * * \param p_usart Pointer to a USART instance. * * \retval 1 Transmit buffers are empty. * \retval 0 Transmit buffers are not empty. */ uint32_t usart_is_tx_buf_empty(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_TXBUFE) > 0; } /** * \brief Get the total number of errors that occur during an ISO7816 transfer. * * \param p_usart Pointer to a USART instance. * * \return The number of errors that occurred. */ uint8_t usart_get_error_number(Usart *p_usart) { return (p_usart->US_NER & US_NER_NB_ERRORS_Msk); } #endif /** * \brief Configure USART to work in SPI mode and act as a master. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_spi_master(Usart *p_usart, const usart_spi_opt_t *p_usart_opt, uint32_t ul_mck) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; /* Check whether the input values are legal. */ if (!p_usart_opt || (p_usart_opt->spi_mode > SPI_MODE_3) || usart_set_spi_master_baudrate(p_usart, p_usart_opt->baudrate, ul_mck)) { return 1; } /* Configure the character length bit in MR register. */ ul_reg_val |= p_usart_opt->char_length; /* Set SPI master mode and channel mode. */ ul_reg_val |= US_MR_USART_MODE_SPI_MASTER | US_MR_CLKO | p_usart_opt->channel_mode; switch (p_usart_opt->spi_mode) { case SPI_MODE_0: ul_reg_val |= US_MR_CPHA; ul_reg_val &= ~US_MR_CPOL; break; case SPI_MODE_1: ul_reg_val &= ~US_MR_CPHA; ul_reg_val &= ~US_MR_CPOL; break; case SPI_MODE_2: ul_reg_val |= US_MR_CPHA; ul_reg_val |= US_MR_CPOL; break; case SPI_MODE_3: ul_reg_val &= ~US_MR_CPHA; ul_reg_val |= US_MR_CPOL; break; default: break; } p_usart->US_MR |= ul_reg_val; return 0; } /** * \brief Configure USART to work in SPI mode and act as a slave. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param p_usart_opt Pointer to sam_usart_opt_t instance. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_spi_slave(Usart *p_usart, const usart_spi_opt_t *p_usart_opt) { static uint32_t ul_reg_val; /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); ul_reg_val = 0; usart_set_spi_slave_baudrate(p_usart); /* Check whether the input values are legal. */ if (!p_usart_opt || p_usart_opt->spi_mode > SPI_MODE_3) { return 1; } /* Configure the character length bit in MR register. */ ul_reg_val |= p_usart_opt->char_length; /* Set SPI slave mode and channel mode. */ ul_reg_val |= US_MR_USART_MODE_SPI_SLAVE | p_usart_opt->channel_mode; switch (p_usart_opt->spi_mode) { case SPI_MODE_0: ul_reg_val |= US_MR_CPHA; ul_reg_val &= ~US_MR_CPOL; break; case SPI_MODE_1: ul_reg_val &= ~US_MR_CPHA; ul_reg_val &= ~US_MR_CPOL; break; case SPI_MODE_2: ul_reg_val |= US_MR_CPHA; ul_reg_val |= US_MR_CPOL; break; case SPI_MODE_3: ul_reg_val |= US_MR_CPOL; ul_reg_val &= ~US_MR_CPHA; break; default: break; } p_usart->US_MR |= ul_reg_val; return 0; } #if (SAM3XA || SAM4L || SAMG55 || SAMV71 || SAMV70 || SAME70 || SAMS70) /** * \brief Configure USART to work in LIN mode and act as a LIN master. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param ul_baudrate Baudrate to be used. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_lin_master(Usart *p_usart,uint32_t ul_baudrate, uint32_t ul_mck) { /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); /* Set up the baudrate. */ if (usart_set_async_baudrate(p_usart, ul_baudrate, ul_mck)) { return 1; } /* Set LIN master mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_LIN_MASTER; usart_enable_rx(p_usart); usart_enable_tx(p_usart); return 0; } /** * \brief Configure USART to work in LIN mode and act as a LIN slave. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param ul_baudrate Baudrate to be used. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_lin_slave(Usart *p_usart, uint32_t ul_baudrate, uint32_t ul_mck) { /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); usart_enable_rx(p_usart); usart_enable_tx(p_usart); /* Set LIN slave mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_LIN_SLAVE; /* Set up the baudrate. */ if (usart_set_async_baudrate(p_usart, ul_baudrate, ul_mck)) { return 1; } return 0; } /** * \brief Abort the current LIN transmission. * * \param p_usart Pointer to a USART instance. */ void usart_lin_abort_tx(Usart *p_usart) { p_usart->US_CR = US_CR_LINABT; } /** * \brief Send a wakeup signal on the LIN bus. * * \param p_usart Pointer to a USART instance. */ void usart_lin_send_wakeup_signal(Usart *p_usart) { p_usart->US_CR = US_CR_LINWKUP; } /** * \brief Configure the LIN node action, which should be one of PUBLISH, * SUBSCRIBE or IGNORE. * * \param p_usart Pointer to a USART instance. * \param uc_action 0 for PUBLISH, 1 for SUBSCRIBE, 2 for IGNORE. */ void usart_lin_set_node_action(Usart *p_usart, uint8_t uc_action) { p_usart->US_LINMR = (p_usart->US_LINMR & ~US_LINMR_NACT_Msk) | (uc_action << US_LINMR_NACT_Pos); } /** * \brief Disable the parity check during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_disable_parity(Usart *p_usart) { p_usart->US_LINMR |= US_LINMR_PARDIS; } /** * \brief Enable the parity check during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_enable_parity(Usart *p_usart) { p_usart->US_LINMR &= ~US_LINMR_PARDIS; } /** * \brief Disable the checksum during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_disable_checksum(Usart *p_usart) { p_usart->US_LINMR |= US_LINMR_CHKDIS; } /** * \brief Enable the checksum during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_enable_checksum(Usart *p_usart) { p_usart->US_LINMR &= ~US_LINMR_CHKDIS; } /** * \brief Configure the checksum type during the LIN communication. * * \param p_usart Pointer to a USART instance. * \param uc_type 0 for LIN 2.0 Enhanced checksum or 1 for LIN 1.3 Classic * checksum. */ void usart_lin_set_checksum_type(Usart *p_usart, uint8_t uc_type) { p_usart->US_LINMR = (p_usart->US_LINMR & ~US_LINMR_CHKTYP) | (uc_type << 4); } /** * \brief Configure the data length mode during the LIN communication. * * \param p_usart Pointer to a USART instance. * \param uc_mode Indicate the data length type: 0 if the data length is * defined by the DLC of LIN mode register or 1 if the data length is defined * by the bit 5 and 6 of the identifier. */ void usart_lin_set_data_len_mode(Usart *p_usart, uint8_t uc_mode) { p_usart->US_LINMR = (p_usart->US_LINMR & ~US_LINMR_DLM) | (uc_mode << 5); } /** * \brief Disable the frame slot mode during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_disable_frame_slot(Usart *p_usart) { p_usart->US_LINMR |= US_LINMR_FSDIS; } /** * \brief Enable the frame slot mode during the LIN communication. * * \param p_usart Pointer to a USART instance. */ void usart_lin_enable_frame_slot(Usart *p_usart) { p_usart->US_LINMR &= ~US_LINMR_FSDIS; } /** * \brief Configure the wakeup signal type during the LIN communication. * * \param p_usart Pointer to a USART instance. * \param uc_type Indicate the checksum type: 0 if the wakeup signal is a * LIN 2.0 wakeup signal; 1 if the wakeup signal is a LIN 1.3 wakeup signal. */ void usart_lin_set_wakeup_signal_type(Usart *p_usart, uint8_t uc_type) { p_usart->US_LINMR = (p_usart->US_LINMR & ~US_LINMR_WKUPTYP) | (uc_type << 7); } /** * \brief Configure the response data length if the data length is defined by * the DLC field during the LIN communication. * * \param p_usart Pointer to a USART instance. * \param uc_len Indicate the response data length. */ void usart_lin_set_response_data_len(Usart *p_usart, uint8_t uc_len) { p_usart->US_LINMR = (p_usart->US_LINMR & ~US_LINMR_DLC_Msk) | ((uc_len - 1) << US_LINMR_DLC_Pos); } /** * \brief The LIN mode register is not written by the PDC. * * \param p_usart Pointer to a USART instance. */ void usart_lin_disable_pdc_mode(Usart *p_usart) { p_usart->US_LINMR &= ~US_LINMR_PDCM; } /** * \brief The LIN mode register (except this flag) is written by the PDC. * * \param p_usart Pointer to a USART instance. */ void usart_lin_enable_pdc_mode(Usart *p_usart) { p_usart->US_LINMR |= US_LINMR_PDCM; } /** * \brief Configure the LIN identifier when USART works in LIN master mode. * * \param p_usart Pointer to a USART instance. * \param uc_id The identifier to be transmitted. */ void usart_lin_set_tx_identifier(Usart *p_usart, uint8_t uc_id) { p_usart->US_LINIR = (p_usart->US_LINIR & ~US_LINIR_IDCHR_Msk) | US_LINIR_IDCHR(uc_id); } /** * \brief Read the identifier when USART works in LIN mode. * * \param p_usart Pointer to a USART instance. * * \return The last identifier received in LIN slave mode or the last * identifier transmitted in LIN master mode. */ uint8_t usart_lin_read_identifier(Usart *p_usart) { return (p_usart->US_LINIR & US_LINIR_IDCHR_Msk); } /** * \brief Get data length. * * \param p_usart Pointer to a USART instance. * * \return Data length. */ uint8_t usart_lin_get_data_length(Usart *usart) { if (usart->US_LINMR & US_LINMR_DLM) { uint8_t data_length = 1 << ((usart->US_LINIR >> (US_LINIR_IDCHR_Pos + 4)) & 0x03); return data_length; } else { return ((usart->US_LINMR & US_LINMR_DLC_Msk) >> US_LINMR_DLC_Pos) + 1; } } #endif #if (SAMV71 || SAMV70 || SAME70 || SAMS70) /** * \brief Get identifier send status. * * \param p_usart Pointer to a USART instance. * * \return * 0: No LIN identifier has been sent since the last RSTSTA. * 1: :At least one LIN identifier has been sent since the last RSTSTA. */ uint8_t usart_lin_identifier_send_complete(Usart *usart) { return (usart->US_CSR & US_CSR_LINID) > 0; } /** * \brief Get identifier received status. * * \param p_usart Pointer to a USART instance. * * \return * 0: No LIN identifier has been reveived since the last RSTSTA. * 1: At least one LIN identifier has been received since the last RSTSTA. */ uint8_t usart_lin_identifier_reception_complete(Usart *usart) { return (usart->US_CSR & US_CSR_LINID) > 0; } /** * \brief Get transmission status. * * \param p_usart Pointer to a USART instance. * * \return * 0: The USART is idle or a LIN transfer is ongoing. * 1: A LIN transfer has been completed since the last RSTSTA. */ uint8_t usart_lin_tx_complete(Usart *usart) { return (usart->US_CSR & US_CSR_LINTC) > 0; } /** * \brief Configure USART to work in LON mode. * * \note By default, the transmitter and receiver aren't enabled. * * \param p_usart Pointer to a USART instance. * \param ul_baudrate Baudrate to be used. * \param ul_mck USART module input clock frequency. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_init_lon(Usart *p_usart,uint32_t ul_baudrate, uint32_t ul_mck) { /* Reset the USART and shut down TX and RX. */ usart_reset(p_usart); /* Set up the baudrate. */ if (usart_set_async_baudrate(p_usart, ul_baudrate, ul_mck)) { return 1; } /* Set LIN master mode. */ p_usart->US_MR = (p_usart->US_MR & ~US_MR_USART_MODE_Msk) | US_MR_USART_MODE_LON; usart_enable_rx(p_usart); usart_enable_tx(p_usart); return 0; } /** * \brief set LON parameter value. * * \param p_usart Pointer to a USART instance. * \param uc_type 0: LON comm_type = 1 mode, * 1: LON comm_type = 2 mode */ void usart_lon_set_comm_type(Usart *p_usart, uint8_t uc_type) { p_usart->US_LONMR = (p_usart->US_LONMR & ~US_LONMR_COMMT) | (uc_type << 0); } /** * \brief Disable LON Collision Detection Feature. * * \param p_usart Pointer to a USART instance. */ void usart_lon_disable_coll_detection(Usart *p_usart) { p_usart->US_LONMR |= US_LONMR_COLDET; } /** * \brief Enable LON Collision Detection Feature. * * \param p_usart Pointer to a USART instance. */ void usart_lon_enable_coll_detection(Usart *p_usart) { p_usart->US_LONMR &= ~US_LONMR_COLDET; } /** * \brief set Terminate Frame upon Collision Notification. * * \param p_usart Pointer to a USART instance. * \param uc_type 0: Do not terminate the frame in LON comm_type = 1 mode upon collision detection. * 1:Terminate the frame in LON comm_type = 1 mode upon collision detection if possible. */ void usart_lon_set_tcol(Usart *p_usart, uint8_t uc_type) { p_usart->US_LONMR = (p_usart->US_LONMR & ~US_LONMR_TCOL) | (uc_type << 2); } /** * \brief set LON Collision Detection on Frame Tail. * * \param p_usart Pointer to a USART instance. * \param uc_type 0: Detect collisions after CRC has been sent but prior end of transmission in LON comm_type = 1 mode. * 1: Ignore collisions after CRC has been sent but prior end of transmission in LON comm_type = 1 mode. */ void usart_lon_set_cdtail(Usart *p_usart, uint8_t uc_type) { p_usart->US_LONMR = (p_usart->US_LONMR & ~US_LONMR_CDTAIL) | (uc_type << 3); } /** * \brief set LON DMA Mode. * * \param p_usart Pointer to a USART instance. * \param uc_type 0: The LON data length register US_LONDL is not written by the DMA. * 1: The LON data length register US_LONDL is written by the DMA. */ void usart_lon_set_dmam(Usart *p_usart, uint8_t uc_type) { p_usart->US_LONMR = (p_usart->US_LONMR & ~US_LONMR_DMAM) | (uc_type << 4); } /** * \brief set LON Beta1 Length after Transmission. * * \param p_usart Pointer to a USART instance. * \param ul_len 1-16777215: LON beta1 length after transmission in tbit */ void usart_lon_set_beta1_tx_len(Usart *p_usart, uint32_t ul_len) { p_usart->US_LONB1TX = US_LONB1TX_BETA1TX(ul_len); } /** * \brief set LON Beta1 Length after Reception. * * \param p_usart Pointer to a USART instance. * \param ul_len 1-16777215: LON beta1 length after reception in tbit. */ void usart_lon_set_beta1_rx_len(Usart *p_usart, uint32_t ul_len) { p_usart->US_LONB1RX = US_LONB1RX_BETA1RX(ul_len); } /** * \brief set LON Priority. * * \param p_usart Pointer to a USART instance. * \param uc_psnb 0 -127: LON Priority Slot Number. * \param uc_nps 0 -127: LON Node Priority Slot. */ void usart_lon_set_priority(Usart *p_usart, uint8_t uc_psnb, uint8_t uc_nps) { p_usart->US_LONPRIO = US_LONPRIO_PSNB(uc_psnb) | US_LONPRIO_NPS(uc_nps); } /** * \brief set LON Indeterminate Time after Transmission. * * \param p_usart Pointer to a USART instance. * \param ul_time 1-16777215: LON Indeterminate Time after Transmission (comm_type = 1 mode only). */ void usart_lon_set_tx_idt(Usart *p_usart, uint32_t ul_time) { p_usart->US_IDTTX = US_IDTTX_IDTTX(ul_time); } /** * \brief set LON Indeterminate Time after Reception. * * \param p_usart Pointer to a USART instance. * \param ul_time 1-16777215: LON Indeterminate Time after Reception (comm_type = 1 mode only). */ void usart_lon_set_rx_idt(Usart *p_usart, uint32_t ul_time) { p_usart->US_IDTRX = US_IDTRX_IDTRX(ul_time); } /** * \brief set LON Preamble Length. * * \param p_usart Pointer to a USART instance. * \param ul_len 1-16383: LON preamble length in tbit(without byte-sync). */ void usart_lon_set_pre_len(Usart *p_usart, uint32_t ul_len) { p_usart->US_LONPR = US_LONPR_LONPL(ul_len); } /** * \brief set LON Data Length. * * \param p_usart Pointer to a USART instance. * \param uc_len 0-255: LON data length is LONDL+1 bytes. */ void usart_lon_set_data_len(Usart *p_usart, uint8_t uc_len) { p_usart->US_LONDL = US_LONDL_LONDL(uc_len); } /** * \brief set LON Priority. * * \param p_usart Pointer to a USART instance. * \param uc_bli LON Backlog Increment. * \param uc_altp LON Alternate Path Bit. * \param uc_pb LON Priority Bit. */ void usart_lon_set_l2hdr(Usart *p_usart, uint8_t uc_bli, uint8_t uc_altp, uint8_t uc_pb) { p_usart->US_LONL2HDR = US_LONL2HDR_BLI(uc_bli) | (uc_altp << 6) | (uc_pb << 7); } /** * \brief Check if LON Transmission End. * * \param p_usart Pointer to a USART instance. * * \retval 1 At least one transmission has been performed since the last RSTSTA. * \retval 0 Transmission on going or no transmission occurred since the last RSTSTA. */ uint32_t usart_lon_is_tx_end(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_LTXD) > 0; } /** * \brief Check if LON Reception End. * * \param p_usart Pointer to a USART instance. * * \retval 1 At least one Reception has been performed since the last RSTSTA. * \retval 0 Reception on going or no Reception occurred since the last RSTSTA. */ uint32_t usart_lon_is_rx_end(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_LRXD) > 0; } #endif /** * \brief Enable USART transmitter. * * \param p_usart Pointer to a USART instance. */ void usart_enable_tx(Usart *p_usart) { p_usart->US_CR = US_CR_TXEN; } /** * \brief Disable USART transmitter. * * \param p_usart Pointer to a USART instance. */ void usart_disable_tx(Usart *p_usart) { p_usart->US_CR = US_CR_TXDIS; } /** * \brief Immediately stop and disable USART transmitter. * * \param p_usart Pointer to a USART instance. */ void usart_reset_tx(Usart *p_usart) { /* Reset transmitter */ p_usart->US_CR = US_CR_RSTTX | US_CR_TXDIS; } /** * \brief Configure the transmit timeguard register. * * \param p_usart Pointer to a USART instance. * \param timeguard The value of transmit timeguard. */ void usart_set_tx_timeguard(Usart *p_usart, uint32_t timeguard) { p_usart->US_TTGR = timeguard; } /** * \brief Enable USART receiver. * * \param p_usart Pointer to a USART instance. */ void usart_enable_rx(Usart *p_usart) { p_usart->US_CR = US_CR_RXEN; } /** * \brief Disable USART receiver. * * \param p_usart Pointer to a USART instance. */ void usart_disable_rx(Usart *p_usart) { p_usart->US_CR = US_CR_RXDIS; } /** * \brief Immediately stop and disable USART receiver. * * \param p_usart Pointer to a USART instance. */ void usart_reset_rx(Usart *p_usart) { /* Reset Receiver */ p_usart->US_CR = US_CR_RSTRX | US_CR_RXDIS; } /** * \brief Configure the receive timeout register. * * \param p_usart Pointer to a USART instance. * \param timeout The value of receive timeout. */ void usart_set_rx_timeout(Usart *p_usart, uint32_t timeout) { p_usart->US_RTOR = timeout; } /** * \brief Enable USART interrupts. * * \param p_usart Pointer to a USART peripheral. * \param ul_sources Interrupt sources bit map. */ void usart_enable_interrupt(Usart *p_usart, uint32_t ul_sources) { p_usart->US_IER = ul_sources; } /** * \brief Disable USART interrupts. * * \param p_usart Pointer to a USART peripheral. * \param ul_sources Interrupt sources bit map. */ void usart_disable_interrupt(Usart *p_usart, uint32_t ul_sources) { p_usart->US_IDR = ul_sources; } /** * \brief Read USART interrupt mask. * * \param p_usart Pointer to a USART peripheral. * * \return The interrupt mask value. */ uint32_t usart_get_interrupt_mask(Usart *p_usart) { return p_usart->US_IMR; } /** * \brief Get current status. * * \param p_usart Pointer to a USART instance. * * \return The current USART status. */ uint32_t usart_get_status(Usart *p_usart) { return p_usart->US_CSR; } /** * \brief Reset status bits (PARE, OVER, MANERR, UNRE and PXBRK in US_CSR). * * \param p_usart Pointer to a USART instance. */ void usart_reset_status(Usart *p_usart) { p_usart->US_CR = US_CR_RSTSTA; } /** * \brief Start transmission of a break. * * \param p_usart Pointer to a USART instance. */ void usart_start_tx_break(Usart *p_usart) { p_usart->US_CR = US_CR_STTBRK; } /** * \brief Stop transmission of a break. * * \param p_usart Pointer to a USART instance. */ void usart_stop_tx_break(Usart *p_usart) { p_usart->US_CR = US_CR_STPBRK; } /** * \brief Start waiting for a character before clocking the timeout count. * Reset the status bit TIMEOUT in US_CSR. * * \param p_usart Pointer to a USART instance. */ void usart_start_rx_timeout(Usart *p_usart) { p_usart->US_CR = US_CR_STTTO; } /** * \brief In Multidrop mode only, the next character written to the US_THR * is sent with the address bit set. * * \param p_usart Pointer to a USART instance. * \param ul_addr The address to be sent out. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_send_address(Usart *p_usart, uint32_t ul_addr) { if ((p_usart->US_MR & US_MR_PAR_MULTIDROP) != US_MR_PAR_MULTIDROP) { return 1; } p_usart->US_CR = US_CR_SENDA; if (usart_write(p_usart, ul_addr)) { return 1; } else { return 0; } } /** * \brief Restart the receive timeout. * * \param p_usart Pointer to a USART instance. */ void usart_restart_rx_timeout(Usart *p_usart) { p_usart->US_CR = US_CR_RETTO; } #if (SAM3S || SAM4S || SAM3U || SAM4L || SAM4E) /** * \brief Drive the pin DTR to 0. * * \param p_usart Pointer to a USART instance. */ void usart_drive_DTR_pin_low(Usart *p_usart) { p_usart->US_CR = US_CR_DTREN; } /** * \brief Drive the pin DTR to 1. * * \param p_usart Pointer to a USART instance. */ void usart_drive_DTR_pin_high(Usart *p_usart) { p_usart->US_CR = US_CR_DTRDIS; } #endif /** * \brief Drive the pin RTS to 0. * * \param p_usart Pointer to a USART instance. */ void usart_drive_RTS_pin_low(Usart *p_usart) { p_usart->US_CR = US_CR_RTSEN; } /** * \brief Drive the pin RTS to 1. * * \param p_usart Pointer to a USART instance. */ void usart_drive_RTS_pin_high(Usart *p_usart) { p_usart->US_CR = US_CR_RTSDIS; } /** * \brief Drive the slave select line NSS (RTS pin) to 0 in SPI master mode. * * \param p_usart Pointer to a USART instance. */ void usart_spi_force_chip_select(Usart *p_usart) { p_usart->US_CR = US_CR_FCS; } /** * \brief Drive the slave select line NSS (RTS pin) to 1 in SPI master mode. * * \param p_usart Pointer to a USART instance. */ void usart_spi_release_chip_select(Usart *p_usart) { p_usart->US_CR = US_CR_RCS; } /** * \brief Check if Transmit is Ready. * Check if data have been loaded in USART_THR and are waiting to be loaded * into the Transmit Shift Register (TSR). * * \param p_usart Pointer to a USART instance. * * \retval 1 No data is in the Transmit Holding Register. * \retval 0 There is data in the Transmit Holding Register. */ uint32_t usart_is_tx_ready(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_TXRDY) > 0; } /** * \brief Check if Transmit Holding Register is empty. * Check if the last data written in USART_THR have been loaded in TSR and the * last data loaded in TSR have been transmitted. * * \param p_usart Pointer to a USART instance. * * \retval 1 Transmitter is empty. * \retval 0 Transmitter is not empty. */ uint32_t usart_is_tx_empty(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_TXEMPTY) > 0; } /** * \brief Check if the received data are ready. * Check if Data have been received and loaded into USART_RHR. * * \param p_usart Pointer to a USART instance. * * \retval 1 Some data has been received. * \retval 0 No data has been received. */ uint32_t usart_is_rx_ready(Usart *p_usart) { return (p_usart->US_CSR & US_CSR_RXRDY) > 0; } /** * \brief Write to USART Transmit Holding Register. * * \note Before writing user should check if tx is ready (or empty). * * \param p_usart Pointer to a USART instance. * \param c Data to be sent. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_write(Usart *p_usart, uint32_t c) { if (!(p_usart->US_CSR & US_CSR_TXRDY)) { return 1; } p_usart->US_THR = US_THR_TXCHR(c); return 0; } /** * \brief Write to USART Transmit Holding Register. * * \note Before writing user should check if tx is ready (or empty). * * \param p_usart Pointer to a USART instance. * \param c Data to be sent. * * \retval 0 on success. * \retval 1 on failure. */ uint32_t usart_putchar(Usart *p_usart, uint32_t c) { while (!(p_usart->US_CSR & US_CSR_TXRDY)) { } p_usart->US_THR = US_THR_TXCHR(c); return 0; } /** * \brief Write one-line string through USART. * * \param p_usart Pointer to a USART instance. * \param string Pointer to one-line string to be sent. */ void usart_write_line(Usart *p_usart, const char *string) { while (*string != '\0') { usart_putchar(p_usart, *string++); } } /** * \brief Read from USART Receive Holding Register. * * \note Before reading user should check if rx is ready. * * \param p_usart Pointer to a USART instance. * \param c Pointer where the one-byte received data will be stored. * * \retval 0 on success. * \retval 1 if no data is available or errors. */ uint32_t usart_read(Usart *p_usart, uint32_t *c) { if (!(p_usart->US_CSR & US_CSR_RXRDY)) { return 1; } /* Read character */ *c = p_usart->US_RHR & US_RHR_RXCHR_Msk; return 0; } /** * \brief Read from USART Receive Holding Register. * Before reading user should check if rx is ready. * * \param p_usart Pointer to a USART instance. * \param c Pointer where the one-byte received data will be stored. * * \retval 0 Data has been received. * \retval 1 on failure. */ uint32_t usart_getchar(Usart *p_usart, uint32_t *c) { /* Wait until it's not empty or timeout has reached. */ while (!(p_usart->US_CSR & US_CSR_RXRDY)) { } /* Read character */ *c = p_usart->US_RHR & US_RHR_RXCHR_Msk; return 0; } #if (SAM3XA || SAM3U) /** * \brief Get Transmit address for DMA operation. * * \param p_usart Pointer to a USART instance. * * \return Transmit address for DMA access. */ uint32_t *usart_get_tx_access(Usart *p_usart) { return (uint32_t *)&(p_usart->US_THR); } /** * \brief Get Receive address for DMA operation. * * \param p_usart Pointer to a USART instance. * * \return Receive address for DMA access. */ uint32_t *usart_get_rx_access(Usart *p_usart) { return (uint32_t *)&(p_usart->US_RHR); } #endif #if (!SAM4L && !SAMV71 && !SAMV70 && !SAME70 && !SAMS70) /** * \brief Get USART PDC base address. * * \param p_usart Pointer to a UART instance. * * \return USART PDC registers base for PDC driver to access. */ Pdc *usart_get_pdc_base(Usart *p_usart) { Pdc *p_pdc_base; p_pdc_base = (Pdc *)NULL; #ifdef PDC_USART if (p_usart == USART) { p_pdc_base = PDC_USART; return p_pdc_base; } #endif #ifdef PDC_USART0 if (p_usart == USART0) { p_pdc_base = PDC_USART0; return p_pdc_base; } #endif #ifdef PDC_USART1 else if (p_usart == USART1) { p_pdc_base = PDC_USART1; return p_pdc_base; } #endif #ifdef PDC_USART2 else if (p_usart == USART2) { p_pdc_base = PDC_USART2; return p_pdc_base; } #endif #ifdef PDC_USART3 else if (p_usart == USART3) { p_pdc_base = PDC_USART3; return p_pdc_base; } #endif #ifdef PDC_USART4 else if (p_usart == USART4) { p_pdc_base = PDC_USART4; return p_pdc_base; } #endif #ifdef PDC_USART5 else if (p_usart == USART5) { p_pdc_base = PDC_USART5; return p_pdc_base; } #endif #ifdef PDC_USART6 else if (p_usart == USART6) { p_pdc_base = PDC_USART6; return p_pdc_base; } #endif #ifdef PDC_USART7 else if (p_usart == USART7) { p_pdc_base = PDC_USART7; return p_pdc_base; } #endif return p_pdc_base; } #endif /** * \brief Enable write protect of USART registers. * * \param p_usart Pointer to a USART instance. */ void usart_enable_writeprotect(Usart *p_usart) { p_usart->US_WPMR = US_WPMR_WPEN | US_WPMR_WPKEY_PASSWD; } /** * \brief Disable write protect of USART registers. * * \param p_usart Pointer to a USART instance. */ void usart_disable_writeprotect(Usart *p_usart) { p_usart->US_WPMR = US_WPMR_WPKEY_PASSWD; } /** * \brief Get write protect status. * * \param p_usart Pointer to a USART instance. * * \return 0 if no write protect violation occurred, or 16-bit write protect * violation source. */ uint32_t usart_get_writeprotect_status(Usart *p_usart) { uint32_t reg_value; reg_value = p_usart->US_WPSR; if (reg_value & US_WPSR_WPVS) { return (reg_value & US_WPSR_WPVSRC_Msk) >> US_WPSR_WPVSRC_Pos; } else { return 0; } } #if (SAM3S || SAM4S || SAM3U || SAM3XA || SAM4L || SAM4E || SAM4C || SAM4CP || SAM4CM) /** * \brief Configure the transmitter preamble length when the Manchester * encode/decode is enabled. * * \param p_usart Pointer to a USART instance. * \param uc_len The transmitter preamble length, which should be 0 ~ 15. */ void usart_man_set_tx_pre_len(Usart *p_usart, uint8_t uc_len) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_TX_PL_Msk) | US_MAN_TX_PL(uc_len); } /** * \brief Configure the transmitter preamble pattern when the Manchester * encode/decode is enabled, which should be 0 ~ 3. * * \param p_usart Pointer to a USART instance. * \param uc_pattern 0 if the preamble is composed of '1's; * 1 if the preamble is composed of '0's; * 2 if the preamble is composed of '01's; * 3 if the preamble is composed of '10's. */ void usart_man_set_tx_pre_pattern(Usart *p_usart, uint8_t uc_pattern) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_TX_PP_Msk) | (uc_pattern << US_MAN_TX_PP_Pos); } /** * \brief Configure the transmitter Manchester polarity when the Manchester * encode/decode is enabled. * * \param p_usart Pointer to a USART instance. * \param uc_polarity Indicate the transmitter Manchester polarity, which * should be 0 or 1. */ void usart_man_set_tx_polarity(Usart *p_usart, uint8_t uc_polarity) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_TX_MPOL) | (uc_polarity << 12); } /** * \brief Configure the detected receiver preamble length when the Manchester * encode/decode is enabled. * * \param p_usart Pointer to a USART instance. * \param uc_len The detected receiver preamble length, which should be 0 ~ 15. */ void usart_man_set_rx_pre_len(Usart *p_usart, uint8_t uc_len) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_RX_PL_Msk) | US_MAN_RX_PL(uc_len); } /** * \brief Configure the detected receiver preamble pattern when the Manchester * encode/decode is enabled, which should be 0 ~ 3. * * \param p_usart Pointer to a USART instance. * \param uc_pattern 0 if the preamble is composed of '1's; * 1 if the preamble is composed of '0's; * 2 if the preamble is composed of '01's; * 3 if the preamble is composed of '10's. */ void usart_man_set_rx_pre_pattern(Usart *p_usart, uint8_t uc_pattern) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_RX_PP_Msk) | (uc_pattern << US_MAN_RX_PP_Pos); } /** * \brief Configure the receiver Manchester polarity when the Manchester * encode/decode is enabled. * * \param p_usart Pointer to a USART instance. * \param uc_polarity Indicate the receiver Manchester polarity, which should * be 0 or 1. */ void usart_man_set_rx_polarity(Usart *p_usart, uint8_t uc_polarity) { p_usart->US_MAN = (p_usart->US_MAN & ~US_MAN_RX_MPOL) | (uc_polarity << 28); } /** * \brief Enable drift compensation. * * \note The 16X clock mode must be enabled. * * \param p_usart Pointer to a USART instance. */ void usart_man_enable_drift_compensation(Usart *p_usart) { p_usart->US_MAN |= US_MAN_DRIFT; } /** * \brief Disable drift compensation. * * \param p_usart Pointer to a USART instance. */ void usart_man_disable_drift_compensation(Usart *p_usart) { p_usart->US_MAN &= ~US_MAN_DRIFT; } #endif #if SAM4L uint32_t usart_get_version(Usart *p_usart) { return p_usart->US_VERSION; } #endif #if SAMG55 /** * \brief Set sleepwalking match mode. * * \param p_uart Pointer to a USART instance. * \param ul_low_value First comparison value for received character. * \param ul_high_value Second comparison value for received character. * \param cmpmode ture for start condition, false for flag only. * \param cmppar ture for parity check, false for no. */ void usart_set_sleepwalking(Usart *p_uart, uint8_t ul_low_value, bool cmpmode, bool cmppar, uint8_t ul_high_value) { Assert(ul_low_value <= ul_high_value); uint32_t temp = 0; if (cmpmode) { temp |= US_CMPR_CMPMODE_START_CONDITION; } if (cmppar) { temp |= US_CMPR_CMPPAR; } temp |= US_CMPR_VAL1(ul_low_value); temp |= US_CMPR_VAL2(ul_high_value); p_uart->US_CMPR= temp; } #endif //@} /// @cond 0 /**INDENT-OFF**/ #ifdef __cplusplus } #endif /**INDENT-ON**/ /// @endcond