Some improvement on mrcrsch's RF24 library
Fork of RF24_fork by
RF24.cpp
- Committer:
- gume
- Date:
- 2018-09-19
- Revision:
- 13:d295c8b3f742
- Parent:
- 10:0a3f44454ee7
File content as of revision 13:d295c8b3f742:
/* Copyright (C) 2011 J. Coliz <maniacbug@ymail.com> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation. */ /* * Mbed support added by Akash Vibhute <akash.roboticist@gmail.com> * Porting completed on Nov/05/2015 * * Updated 1: Synced with TMRh20's RF24 library on Nov/04/2015 from https://github.com/TMRh20 * Updated 2: Synced with TMRh20's RF24 library on Apr/18/2015 from https://github.com/TMRh20 * */ #include "nRF24L01.h" #include "RF24_config.h" #include "RF24.h" /****************************************************************************/ void RF24::csn(bool mode) { csn_pin = mode; } /****************************************************************************/ void RF24::ce(bool level) { ce_pin = level; } /****************************************************************************/ inline void RF24::beginTransaction() { csn(LOW); } /****************************************************************************/ inline void RF24::endTransaction() { csn(HIGH); } /****************************************************************************/ uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len) { uint8_t status; beginTransaction(); status = spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); while ( len-- ){ *buf++ = spi.write(0xff); } endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::read_register(uint8_t reg) { uint8_t result; beginTransaction(); spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); result = spi.write(0xff); endTransaction(); return result; } /****************************************************************************/ uint8_t RF24::write_register(uint8_t reg, const uint8_t* buf, uint8_t len) { uint8_t status; beginTransaction(); status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); while ( len-- ) spi.write(*buf++); endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::write_register(uint8_t reg, uint8_t value) { uint8_t status; IF_SERIAL_DEBUG(printf_P(PSTR("write_register(%02x,%02x)\r\n"),reg,value)); beginTransaction(); status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); spi.write(value); endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::write_payload(const void* buf, uint8_t data_len, const uint8_t writeType) { uint8_t status; const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); data_len = rf24_min(data_len, payload_size); uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; //printf("[Writing %u bytes %u blanks]",data_len,blank_len); IF_SERIAL_DEBUG( printf("[Writing %u bytes %u blanks]\n",data_len,blank_len); ); beginTransaction(); status = spi.write( writeType ); while ( data_len-- ) { spi.write(*current++); } while ( blank_len-- ) { spi.write(0); } endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::read_payload(void* buf, uint8_t data_len) { uint8_t status; uint8_t* current = reinterpret_cast<uint8_t*>(buf); if(data_len > payload_size) data_len = payload_size; uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; //printf("[Reading %u bytes %u blanks]",data_len,blank_len); IF_SERIAL_DEBUG( printf("[Reading %u bytes %u blanks]\n",data_len,blank_len); ); beginTransaction(); status = spi.write( R_RX_PAYLOAD ); while ( data_len-- ) { *current++ = spi.write(0xFF); } while ( blank_len-- ) { spi.write(0xff); } endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::flush_rx(void) { return spiTrans( FLUSH_RX ); } /****************************************************************************/ uint8_t RF24::flush_tx(void) { return spiTrans( FLUSH_TX ); } /****************************************************************************/ uint8_t RF24::spiTrans(uint8_t cmd){ uint8_t status; beginTransaction(); status = spi.write( cmd ); endTransaction(); return status; } /****************************************************************************/ uint8_t RF24::get_status(void) { return spiTrans(NOP); } /****************************************************************************/ #if !defined (MINIMAL) void RF24::print_status(uint8_t status) { printf_P(PSTR("STATUS\t\t = 0x%02x RX_DR=%x TX_DS=%x MAX_RT=%x RX_P_NO=%x TX_FULL=%x\r\n"), status, (status & _BV(RX_DR))?1:0, (status & _BV(TX_DS))?1:0, (status & _BV(MAX_RT))?1:0, ((status >> RX_P_NO) & 0b111), (status & _BV(TX_FULL))?1:0 ); } /****************************************************************************/ void RF24::print_observe_tx(uint8_t value) { printf_P(PSTR("OBSERVE_TX=%02x: POLS_CNT=%x ARC_CNT=%x\r\n"), value, (value >> PLOS_CNT) & 0b1111, (value >> ARC_CNT) & 0b1111 ); } /****************************************************************************/ void RF24::print_byte_register(const char* name, uint8_t reg, uint8_t qty) { //char extra_tab = strlen_P(name) < 8 ? '\t' : 0; //printf_P(PSTR(PRIPSTR"\t%c ="),name,extra_tab); printf_P(PSTR(PRIPSTR"\t ="),name); while (qty--) printf_P(PSTR(" 0x%02x"),read_register(reg++)); printf_P(PSTR("\r\n")); } /****************************************************************************/ void RF24::print_address_register(const char* name, uint8_t reg, uint8_t qty) { printf_P(PSTR(PRIPSTR"\t ="),name); while (qty--) { uint8_t buffer[addr_width]; read_register(reg++,buffer,sizeof buffer); printf_P(PSTR(" 0x")); uint8_t* bufptr = buffer + sizeof buffer; while( --bufptr >= buffer ) printf_P(PSTR("%02x"),*bufptr); } printf_P(PSTR("\r\n")); } #endif /****************************************************************************/ RF24::RF24(PinName mosi, PinName miso, PinName sck, PinName _cepin, PinName _csnpin): spi(mosi, miso, sck), ce_pin(_cepin), csn_pin(_csnpin), p_variant(true), payload_size(32), dynamic_payloads_enabled(false), addr_width(5) { pipe0_reading_address[0]=0; //spi.frequency(10000000/5); // 2Mbit, 1/5th the maximum transfer rate for the spi bus spi.frequency(10000000); //spi.format(8,0); // 8-bit, ClockPhase = 0, ClockPolarity = 0 spi.format(8,0); wait_ms(10); } /****************************************************************************/ void RF24::setChannel(uint8_t channel) { const uint8_t max_channel = 125; write_register(RF_CH,rf24_min(channel,max_channel)); } uint8_t RF24::getChannel() { return read_register(RF_CH); } /****************************************************************************/ void RF24::setPayloadSize(uint8_t size) { payload_size = rf24_min(size,32); } /****************************************************************************/ uint8_t RF24::getPayloadSize(void) { return payload_size; } /****************************************************************************/ #if !defined (MINIMAL) static const char rf24_datarate_e_str_0[] PROGMEM = "1MBPS"; static const char rf24_datarate_e_str_1[] PROGMEM = "2MBPS"; static const char rf24_datarate_e_str_2[] PROGMEM = "250KBPS"; static const char * const rf24_datarate_e_str_P[] PROGMEM = { rf24_datarate_e_str_0, rf24_datarate_e_str_1, rf24_datarate_e_str_2, }; static const char rf24_model_e_str_0[] PROGMEM = "nRF24L01"; static const char rf24_model_e_str_1[] PROGMEM = "nRF24L01+"; static const char * const rf24_model_e_str_P[] PROGMEM = { rf24_model_e_str_0, rf24_model_e_str_1, }; static const char rf24_crclength_e_str_0[] PROGMEM = "Disabled"; static const char rf24_crclength_e_str_1[] PROGMEM = "8 bits"; static const char rf24_crclength_e_str_2[] PROGMEM = "16 bits" ; static const char * const rf24_crclength_e_str_P[] PROGMEM = { rf24_crclength_e_str_0, rf24_crclength_e_str_1, rf24_crclength_e_str_2, }; static const char rf24_pa_dbm_e_str_0[] PROGMEM = "PA_MIN"; static const char rf24_pa_dbm_e_str_1[] PROGMEM = "PA_LOW"; static const char rf24_pa_dbm_e_str_2[] PROGMEM = "PA_HIGH"; static const char rf24_pa_dbm_e_str_3[] PROGMEM = "PA_MAX"; static const char * const rf24_pa_dbm_e_str_P[] PROGMEM = { rf24_pa_dbm_e_str_0, rf24_pa_dbm_e_str_1, rf24_pa_dbm_e_str_2, rf24_pa_dbm_e_str_3, }; void RF24::printDetails(void) { print_status(get_status()); print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2); print_byte_register(PSTR("RX_ADDR_P2-5"),RX_ADDR_P2,4); print_address_register(PSTR("TX_ADDR\t"),TX_ADDR); print_byte_register(PSTR("RX_PW_P0-6"),RX_PW_P0,6); print_byte_register(PSTR("EN_AA\t"),EN_AA); print_byte_register(PSTR("EN_RXADDR"),EN_RXADDR); print_byte_register(PSTR("RF_CH\t"),RF_CH); print_byte_register(PSTR("RF_SETUP"),RF_SETUP); print_byte_register(PSTR("CONFIG\t"),NRF_CONFIG); print_byte_register(PSTR("DYNPD/FEATURE"),DYNPD,2); printf_P(PSTR("Data Rate\t = " PRIPSTR "\r\n"),pgm_read_word(&rf24_datarate_e_str_P[getDataRate()])); printf_P(PSTR("Model\t\t = " PRIPSTR "\r\n"),pgm_read_word(&rf24_model_e_str_P[isPVariant()])); printf_P(PSTR("CRC Length\t = " PRIPSTR "\r\n"),pgm_read_word(&rf24_crclength_e_str_P[getCRCLength()])); printf_P(PSTR("PA Power\t = " PRIPSTR "\r\n"), pgm_read_word(&rf24_pa_dbm_e_str_P[getPALevel()])); } #endif /****************************************************************************/ bool RF24::begin(void) { uint8_t setup=0; mainTimer.start(); ce(LOW); csn(HIGH); wait_ms(100); // Must allow the radio time to settle else configuration bits will not necessarily stick. // This is actually only required following power up but some settling time also appears to // be required after resets too. For full coverage, we'll always assume the worst. // Enabling 16b CRC is by far the most obvious case if the wrong timing is used - or skipped. // Technically we require 4.5ms + 14us as a worst case. We'll just call it 5ms for good measure. // WARNING: Delay is based on P-variant whereby non-P *may* require different timing. wait_ms( 5 ) ; // Reset NRF_CONFIG and enable 16-bit CRC. write_register( NRF_CONFIG, 0b00001100 ) ; // Set 1500uS (minimum for 32B payload in ESB@250KBPS) timeouts, to make testing a little easier // WARNING: If this is ever lowered, either 250KBS mode with AA is broken or maximum packet // sizes must never be used. See documentation for a more complete explanation. setRetries(5,15); // Reset value is MAX //setPALevel( RF24_PA_MAX ) ; // check for connected module and if this is a p nRF24l01 variant // if( setDataRate( RF24_250KBPS ) ) { p_variant = true ; } setup = read_register(RF_SETUP); /*if( setup == 0b00001110 ) // register default for nRF24L01P { p_variant = true ; }*/ // Then set the data rate to the slowest (and most reliable) speed supported by all // hardware. //setDataRate( RF24_1MBPS ) ; setDataRate( RF24_2MBPS ) ; // Initialize CRC and request 2-byte (16bit) CRC //setCRCLength( RF24_CRC_16 ) ; // Disable dynamic payloads, to match dynamic_payloads_enabled setting - Reset value is 0 toggle_features(); write_register(FEATURE,0 ); write_register(DYNPD,0); // Reset current status // Notice reset and flush is the last thing we do write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); // Set up default configuration. Callers can always change it later. // This channel should be universally safe and not bleed over into adjacent // spectrum. setChannel(76); // Flush buffers flush_rx(); flush_tx(); powerUp(); //Power up by default when begin() is called // Enable PTX, do not write CE high so radio will remain in standby I mode ( 130us max to transition to RX or TX instead of 1500us from powerUp ) // PTX should use only 22uA of power write_register(NRF_CONFIG, ( read_register(NRF_CONFIG) ) & ~_BV(PRIM_RX) ); //printDetails(); // if setup is 0 or ff then there was no response from module return ( setup != 0 && setup != 0xff ); } /****************************************************************************/ void RF24::startListening(void) { write_register(NRF_CONFIG, read_register(NRF_CONFIG) | _BV(PRIM_RX)); write_register(NRF_STATUS, _BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); ce(HIGH); // Restore the pipe0 adddress, if exists if (pipe0_reading_address[0] > 0){ write_register(RX_ADDR_P0, pipe0_reading_address, addr_width); }else{ closeReadingPipe(0); } // Flush buffers //flush_rx(); if(read_register(FEATURE) & _BV(EN_ACK_PAY)){ flush_tx(); } // Go! //delayMicroseconds(100); } /****************************************************************************/ static const uint8_t child_pipe_enable[] PROGMEM = { ERX_P0, ERX_P1, ERX_P2, ERX_P3, ERX_P4, ERX_P5 }; void RF24::stopListening(void) { ce(LOW); wait_us(txRxDelay); if(read_register(FEATURE) & _BV(EN_ACK_PAY)){ wait_us(txRxDelay); //200 flush_tx(); } //flush_rx(); write_register(NRF_CONFIG, ( read_register(NRF_CONFIG) ) & ~_BV(PRIM_RX) ); write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[0]))); // Enable RX on pipe0 //delayMicroseconds(100); } /****************************************************************************/ void RF24::powerDown(void) { ce(LOW); // Guarantee CE is low on powerDown write_register(NRF_CONFIG,read_register(NRF_CONFIG) & ~_BV(PWR_UP)); } /****************************************************************************/ //Power up now. Radio will not power down unless instructed by MCU for config changes etc. void RF24::powerUp(void) { uint8_t cfg = read_register(NRF_CONFIG); // if not powered up then power up and wait for the radio to initialize if (!(cfg & _BV(PWR_UP))){ write_register(NRF_CONFIG, cfg | _BV(PWR_UP)); // For nRF24L01+ to go from power down mode to TX or RX mode it must first pass through stand-by mode. // There must be a delay of Tpd2stby (see Table 16.) after the nRF24L01+ leaves power down mode before // the CEis set high. - Tpd2stby can be up to 5ms per the 1.0 datasheet wait_ms(5); } } /******************************************************************/ #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) void RF24::errNotify(){ #if defined (SERIAL_DEBUG) || defined (RF24_LINUX) printf_P(PSTR("RF24 HARDWARE FAIL: Radio not responding, verify pin connections, wiring, etc.\r\n")); #endif #if defined (FAILURE_HANDLING) failureDetected = 1; #else wait_ms(5000); #endif } #endif /******************************************************************/ //Similar to the previous write, clears the interrupt flags bool RF24::write( const void* buf, uint8_t len, const bool multicast ) { //Start Writing startFastWrite(buf,len,multicast); //Wait until complete or failed #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) uint32_t timer = mainTimer.read_ms(); #endif while( ! ( get_status() & ( _BV(TX_DS) | _BV(MAX_RT) ))) { #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) if(mainTimer.read_ms() - timer > 95){ errNotify(); #if defined (FAILURE_HANDLING) return 0; #else wait_ms(100); #endif } #endif } ce(LOW); uint8_t status = write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); //Max retries exceeded if( status & _BV(MAX_RT)){ flush_tx(); //Only going to be 1 packet int the FIFO at a time using this method, so just flush return 0; } //TX OK 1 or 0 return 1; } bool RF24::write( const void* buf, uint8_t len ){ return write(buf,len,0); } /****************************************************************************/ //For general use, the interrupt flags are not important to clear bool RF24::writeBlocking( const void* buf, uint8_t len, uint32_t timeout ) { //Block until the FIFO is NOT full. //Keep track of the MAX retries and set auto-retry if seeing failures //This way the FIFO will fill up and allow blocking until packets go through //The radio will auto-clear everything in the FIFO as long as CE remains high uint32_t timer = mainTimer.read_ms(); //Get the time that the payload transmission started while( ( get_status() & ( _BV(TX_FULL) ))) { //Blocking only if FIFO is full. This will loop and block until TX is successful or timeout if( get_status() & _BV(MAX_RT)){ //If MAX Retries have been reached reUseTX(); //Set re-transmit and clear the MAX_RT interrupt flag if(mainTimer.read_ms() - timer > timeout){ return 0; } //If this payload has exceeded the user-defined timeout, exit and return 0 } #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) if(mainTimer.read_ms() - timer > (timeout+95) ){ errNotify(); #if defined (FAILURE_HANDLING) return 0; #endif } #endif } //Start Writing startFastWrite(buf,len,0); //Write the payload if a buffer is clear return 1; //Return 1 to indicate successful transmission } /****************************************************************************/ void RF24::reUseTX(){ write_register(NRF_STATUS,_BV(MAX_RT) ); //Clear max retry flag spiTrans( REUSE_TX_PL ); ce(LOW); //Re-Transfer packet ce(HIGH); } /****************************************************************************/ bool RF24::writeFast( const void* buf, uint8_t len, const bool multicast ) { //Block until the FIFO is NOT full. //Keep track of the MAX retries and set auto-retry if seeing failures //Return 0 so the user can control the retrys and set a timer or failure counter if required //The radio will auto-clear everything in the FIFO as long as CE remains high #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) uint32_t timer = mainTimer.read_ms(); #endif while( ( get_status() & ( _BV(TX_FULL) ))) { //Blocking only if FIFO is full. This will loop and block until TX is successful or fail if( get_status() & _BV(MAX_RT)){ //reUseTX(); //Set re-transmit write_register(NRF_STATUS,_BV(MAX_RT) ); //Clear max retry flag return 0; //Return 0. The previous payload has been retransmitted //From the user perspective, if you get a 0, just keep trying to send the same payload } #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) if(mainTimer.read_ms() - timer > 95 ){ errNotify(); #if defined (FAILURE_HANDLING) return 0; #endif } #endif } //Start Writing startFastWrite(buf,len,multicast); return 1; } bool RF24::writeFast( const void* buf, uint8_t len ){ return writeFast(buf,len,0); } /****************************************************************************/ //Per the documentation, we want to set PTX Mode when not listening. Then all we do is write data and set CE high //In this mode, if we can keep the FIFO buffers loaded, packets will transmit immediately (no 130us delay) //Otherwise we enter Standby-II mode, which is still faster than standby mode //Also, we remove the need to keep writing the config register over and over and delaying for 150 us each time if sending a stream of data void RF24::startFastWrite( const void* buf, uint8_t len, const bool multicast, bool startTx){ //TMRh20 //write_payload( buf,len); write_payload( buf, len,multicast ? W_TX_PAYLOAD_NO_ACK : W_TX_PAYLOAD ) ; if(startTx){ ce(HIGH); } } /****************************************************************************/ //Added the original startWrite back in so users can still use interrupts, ack payloads, etc //Allows the library to pass all tests void RF24::startWrite( const void* buf, uint8_t len, const bool multicast ){ // Send the payload //write_payload( buf, len ); write_payload( buf, len,multicast? W_TX_PAYLOAD_NO_ACK : W_TX_PAYLOAD ) ; ce(HIGH); wait_us(10); ce(LOW); } /****************************************************************************/ bool RF24::rxFifoFull(){ return read_register(FIFO_STATUS) & _BV(RX_FULL); } /****************************************************************************/ bool RF24::txStandBy(){ #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) uint32_t timeout = mainTimer.read_ms(); #endif while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ){ if( get_status() & _BV(MAX_RT)){ write_register(NRF_STATUS,_BV(MAX_RT) ); ce(LOW); flush_tx(); //Non blocking, flush the data return 0; } #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) if( mainTimer.read_ms() - timeout > 95){ errNotify(); #if defined (FAILURE_HANDLING) return 0; #endif } #endif } ce(LOW); //Set STANDBY-I mode return 1; } /****************************************************************************/ bool RF24::txStandBy(uint32_t timeout, bool startTx){ if(startTx){ stopListening(); ce(HIGH); } uint32_t start = mainTimer.read_ms(); while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ){ if( get_status() & _BV(MAX_RT)){ write_register(NRF_STATUS,_BV(MAX_RT) ); ce(LOW); //Set re-transmit ce(HIGH); if(mainTimer.read_ms() - start >= timeout){ ce(LOW); flush_tx(); return 0; } } #if defined (FAILURE_HANDLING) || defined (RF24_LINUX) if( mainTimer.read_ms() - start > (timeout+95)){ errNotify(); #if defined (FAILURE_HANDLING) return 0; #endif } #endif } ce(LOW); //Set STANDBY-I mode return 1; } /****************************************************************************/ void RF24::maskIRQ(bool tx, bool fail, bool rx){ uint8_t config = read_register(NRF_CONFIG); /* clear the interrupt flags */ config &= ~(1 << MASK_MAX_RT | 1 << MASK_TX_DS | 1 << MASK_RX_DR); /* set the specified interrupt flags */ config |= fail << MASK_MAX_RT | tx << MASK_TX_DS | rx << MASK_RX_DR; write_register(NRF_CONFIG, config); } /****************************************************************************/ uint8_t RF24::getDynamicPayloadSize(void) { uint8_t result = 0; beginTransaction(); spi.write( R_RX_PL_WID ); result = spi.write(0xff); endTransaction(); if(result > 32) { flush_rx(); wait_ms(2); return 0; } return result; } /****************************************************************************/ bool RF24::available(void) { return available(NULL); } /****************************************************************************/ bool RF24::available(uint8_t* pipe_num) { if (!( read_register(FIFO_STATUS) & _BV(RX_EMPTY) )){ // If the caller wants the pipe number, include that if ( pipe_num ){ uint8_t status = get_status(); *pipe_num = ( status >> RX_P_NO ) & 0b111; } return 1; } return 0; } /****************************************************************************/ void RF24::read( void* buf, uint8_t len ){ // Fetch the payload read_payload( buf, len ); //Clear the two possible interrupt flags with one command write_register(NRF_STATUS,_BV(RX_DR) | _BV(MAX_RT) | _BV(TX_DS) ); } /****************************************************************************/ void RF24::whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready) { // Read the status & reset the status in one easy call // Or is that such a good idea? uint8_t status = write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); // Report to the user what happened tx_ok = status & _BV(TX_DS); tx_fail = status & _BV(MAX_RT); rx_ready = status & _BV(RX_DR); } /****************************************************************************/ void RF24::openWritingPipe(uint64_t value) { // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) // expects it LSB first too, so we're good. write_register(RX_ADDR_P0, reinterpret_cast<uint8_t*>(&value), addr_width); write_register(TX_ADDR, reinterpret_cast<uint8_t*>(&value), addr_width); //const uint8_t max_payload_size = 32; //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); write_register(RX_PW_P0,payload_size); } /****************************************************************************/ void RF24::openWritingPipe(const uint8_t *address) { // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) // expects it LSB first too, so we're good. write_register(RX_ADDR_P0,address, addr_width); write_register(TX_ADDR, address, addr_width); //const uint8_t max_payload_size = 32; //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); write_register(RX_PW_P0,payload_size); } /****************************************************************************/ static const uint8_t child_pipe[] PROGMEM = { RX_ADDR_P0, RX_ADDR_P1, RX_ADDR_P2, RX_ADDR_P3, RX_ADDR_P4, RX_ADDR_P5 }; static const uint8_t child_payload_size[] PROGMEM = { RX_PW_P0, RX_PW_P1, RX_PW_P2, RX_PW_P3, RX_PW_P4, RX_PW_P5 }; void RF24::openReadingPipe(uint8_t child, uint64_t address) { // If this is pipe 0, cache the address. This is needed because // openWritingPipe() will overwrite the pipe 0 address, so // startListening() will have to restore it. if (child == 0){ memcpy(pipe0_reading_address,&address,addr_width); } if (child <= 6) { // For pipes 2-5, only write the LSB if ( child < 2 ) write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), addr_width); else write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), 1); write_register(pgm_read_byte(&child_payload_size[child]),payload_size); // Note it would be more efficient to set all of the bits for all open // pipes at once. However, I thought it would make the calling code // more simple to do it this way. write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); } } /****************************************************************************/ void RF24::setAddressWidth(uint8_t a_width){ if(a_width -= 2){ write_register(SETUP_AW,a_width%4); addr_width = (a_width%4) + 2; } } /****************************************************************************/ void RF24::openReadingPipe(uint8_t child, const uint8_t *address) { // If this is pipe 0, cache the address. This is needed because // openWritingPipe() will overwrite the pipe 0 address, so // startListening() will have to restore it. if (child == 0){ memcpy(pipe0_reading_address,address,addr_width); } if (child <= 6) { // For pipes 2-5, only write the LSB if ( child < 2 ){ write_register(pgm_read_byte(&child_pipe[child]), address, addr_width); }else{ write_register(pgm_read_byte(&child_pipe[child]), address, 1); } write_register(pgm_read_byte(&child_payload_size[child]),payload_size); // Note it would be more efficient to set all of the bits for all open // pipes at once. However, I thought it would make the calling code // more simple to do it this way. write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); } } /****************************************************************************/ void RF24::closeReadingPipe( uint8_t pipe ) { write_register(EN_RXADDR,read_register(EN_RXADDR) & ~_BV(pgm_read_byte(&child_pipe_enable[pipe]))); } /****************************************************************************/ void RF24::toggle_features(void) { beginTransaction(); spi.write( ACTIVATE ); spi.write( 0x73 ); endTransaction(); } /****************************************************************************/ void RF24::enableDynamicPayloads(void) { // Enable dynamic payload throughout the system //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) ); IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); // Enable dynamic payload on all pipes // // Not sure the use case of only having dynamic payload on certain // pipes, so the library does not support it. write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P5) | _BV(DPL_P4) | _BV(DPL_P3) | _BV(DPL_P2) | _BV(DPL_P1) | _BV(DPL_P0)); dynamic_payloads_enabled = true; } /****************************************************************************/ void RF24::enableAckPayload(void) { // // enable ack payload and dynamic payload features // //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) ); IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); // // Enable dynamic payload on pipes 0 & 1 // write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0)); dynamic_payloads_enabled = true; } /****************************************************************************/ void RF24::enableDynamicAck(void){ // // enable dynamic ack features // //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_DYN_ACK) ); IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); } /****************************************************************************/ void RF24::writeAckPayload(uint8_t pipe, const void* buf, uint8_t len) { const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); uint8_t data_len = rf24_min(len,32); beginTransaction(); spi.write(W_ACK_PAYLOAD | ( pipe & 0b111 ) ); while ( data_len-- ) spi.write(*current++); endTransaction(); } /****************************************************************************/ bool RF24::isAckPayloadAvailable(void) { return ! (read_register(FIFO_STATUS) & _BV(RX_EMPTY)); } /****************************************************************************/ bool RF24::isPVariant(void) { return p_variant ; } /****************************************************************************/ void RF24::setAutoAck(bool enable) { if ( enable ) write_register(EN_AA, 0b111111); else write_register(EN_AA, 0); } /****************************************************************************/ void RF24::setAutoAck( uint8_t pipe, bool enable ) { if ( pipe <= 6 ) { uint8_t en_aa = read_register( EN_AA ) ; if( enable ) { en_aa |= _BV(pipe) ; } else { en_aa &= ~_BV(pipe) ; } write_register( EN_AA, en_aa ) ; } } /****************************************************************************/ bool RF24::testCarrier(void) { return ( read_register(CD) & 1 ); } /****************************************************************************/ bool RF24::testRPD(void) { return ( read_register(RPD) & 1 ) ; } /****************************************************************************/ void RF24::setPALevel(uint8_t level) { uint8_t setup = read_register(RF_SETUP) & 0b11111000; if(level > 3){ // If invalid level, go to max PA level = (RF24_PA_MAX << 1) + 1; // +1 to support the SI24R1 chip extra bit }else{ level = (level << 1) + 1; // Else set level as requested } write_register( RF_SETUP, setup |= level ) ; // Write it to the chip } /****************************************************************************/ uint8_t RF24::getPALevel(void) { return (read_register(RF_SETUP) & (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH))) >> 1 ; } /****************************************************************************/ bool RF24::setDataRate(rf24_datarate_e speed) { bool result = false; uint8_t setup = read_register(RF_SETUP) ; // HIGH and LOW '00' is 1Mbs - our default setup &= ~(_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) ; txRxDelay=85; if( speed == RF24_250KBPS ) { // Must set the RF_DR_LOW to 1; RF_DR_HIGH (used to be RF_DR) is already 0 // Making it '10'. setup |= _BV( RF_DR_LOW ) ; txRxDelay=155; } else { // Set 2Mbs, RF_DR (RF_DR_HIGH) is set 1 // Making it '01' if ( speed == RF24_2MBPS ) { setup |= _BV(RF_DR_HIGH); //txRxDelay=65; txRxDelay=15; //mbed works fine with this latency } } write_register(RF_SETUP,setup); // Verify our result if ( read_register(RF_SETUP) == setup ) { result = true; } return result; } /****************************************************************************/ rf24_datarate_e RF24::getDataRate( void ) { rf24_datarate_e result ; uint8_t dr = read_register(RF_SETUP) & (_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)); // switch uses RAM (evil!) // Order matters in our case below if ( dr == _BV(RF_DR_LOW) ) { // '10' = 250KBPS result = RF24_250KBPS ; } else if ( dr == _BV(RF_DR_HIGH) ) { // '01' = 2MBPS result = RF24_2MBPS ; } else { // '00' = 1MBPS result = RF24_1MBPS ; } return result ; } /****************************************************************************/ void RF24::setCRCLength(rf24_crclength_e length) { uint8_t config = read_register(NRF_CONFIG) & ~( _BV(CRCO) | _BV(EN_CRC)) ; // switch uses RAM (evil!) if ( length == RF24_CRC_DISABLED ) { // Do nothing, we turned it off above. } else if ( length == RF24_CRC_8 ) { config |= _BV(EN_CRC); } else { config |= _BV(EN_CRC); config |= _BV( CRCO ); } write_register( NRF_CONFIG, config ) ; } /****************************************************************************/ rf24_crclength_e RF24::getCRCLength(void) { rf24_crclength_e result = RF24_CRC_DISABLED; uint8_t config = read_register(NRF_CONFIG) & ( _BV(CRCO) | _BV(EN_CRC)) ; uint8_t AA = read_register(EN_AA); if ( config & _BV(EN_CRC ) || AA) { if ( config & _BV(CRCO) ) result = RF24_CRC_16; else result = RF24_CRC_8; } return result; } /****************************************************************************/ void RF24::disableCRC( void ) { uint8_t disable = read_register(NRF_CONFIG) & ~_BV(EN_CRC) ; write_register( NRF_CONFIG, disable ) ; } /****************************************************************************/ void RF24::setRetries(uint8_t delay, uint8_t count) { write_register(SETUP_RETR,(delay&0xf)<<ARD | (count&0xf)<<ARC); } /****************************************************************************/ bool RF24::isChipConnected() { uint8_t setup = read_register(SETUP_AW); if(setup >= 1 && setup <= 3) return true; return false; }