Diff: source/hic_hal/stm32/stm32f103xb/IO_Config.h

Revision:

0:01f31e923fe2

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/source/hic_hal/stm32/stm32f103xb/IO_Config.h	Tue Apr 07 12:55:42 2020 +0200
@@ -0,0 +1,86 @@
+/**
+ * @file    IO_Config.h
+ * @brief
+ *
+ * DAPLink Interface Firmware
+ * Copyright (c) 2009-2016, ARM Limited, All Rights Reserved
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __IO_CONFIG_H__
+#define __IO_CONFIG_H__
+
+#include "stm32f1xx.h"
+#include "compiler.h"
+#include "daplink.h"
+
+COMPILER_ASSERT(DAPLINK_HIC_ID == DAPLINK_HIC_ID_STM32F103XB);
+
+//USB control pin
+#define USB_CONNECT_PORT_ENABLE()    __HAL_RCC_GPIOA_CLK_ENABLE()
+#define USB_CONNECT_PORT_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
+#define USB_CONNECT_PORT             GPIOA
+#define USB_CONNECT_PIN              GPIO_PIN_15
+#define USB_CONNECT_ON()             (USB_CONNECT_PORT->BSRR = USB_CONNECT_PIN)
+#define USB_CONNECT_OFF()            (USB_CONNECT_PORT->BRR  = USB_CONNECT_PIN)
+
+//Connected LED
+#define CONNECTED_LED_PORT           GPIOB
+#define CONNECTED_LED_PIN            GPIO_PIN_6
+#define CONNECTED_LED_PIN_Bit        6
+
+//When bootloader, disable the target port(not used)
+#define POWER_EN_PIN_PORT            GPIOB
+#define POWER_EN_PIN                 GPIO_PIN_15
+#define POWER_EN_Bit                 15
+
+// nRESET OUT Pin
+#define nRESET_PIN_PORT              GPIOB
+#define nRESET_PIN                   GPIO_PIN_0
+#define nRESET_PIN_Bit               0
+
+//SWD
+#define SWCLK_TCK_PIN_PORT           GPIOB
+#define SWCLK_TCK_PIN                GPIO_PIN_13
+#define SWCLK_TCK_PIN_Bit            13
+
+#define SWDIO_OUT_PIN_PORT           GPIOB
+#define SWDIO_OUT_PIN                GPIO_PIN_14
+#define SWDIO_OUT_PIN_Bit            14
+
+#define SWDIO_IN_PIN_PORT            GPIOB
+#define SWDIO_IN_PIN                 GPIO_PIN_12
+#define SWDIO_IN_PIN_Bit             12
+
+//LEDs
+//USB status LED
+#define RUNNING_LED_PORT             GPIOA
+#define RUNNING_LED_PIN              GPIO_PIN_9
+#define RUNNING_LED_Bit              9
+
+#define PIN_HID_LED_PORT             GPIOA
+#define PIN_HID_LED                  GPIO_PIN_9
+#define PIN_HID_LED_Bit              9
+
+#define PIN_CDC_LED_PORT             GPIOA
+#define PIN_CDC_LED                  GPIO_PIN_9
+#define PIN_CDC_LED_Bit              9
+
+#define PIN_MSC_LED_PORT             GPIOA
+#define PIN_MSC_LED                  GPIO_PIN_9
+#define PIN_MSC_LED_Bit              9
+
+
+#endif