Diff: source/hic_hal/freescale/k26f/fsl_uart.h

Revision:

0:01f31e923fe2

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/source/hic_hal/freescale/k26f/fsl_uart.h	Tue Apr 07 12:55:42 2020 +0200
@@ -0,0 +1,782 @@
+/*
+ * Copyright (c) 2015-2016, Freescale Semiconductor, Inc.
+ * Copyright 2016-2017 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+#ifndef _FSL_UART_H_
+#define _FSL_UART_H_
+
+#include "fsl_common.h"
+
+/*!
+ * @addtogroup uart_driver
+ * @{
+ */
+
+/*******************************************************************************
+ * Definitions
+ ******************************************************************************/
+
+/*! @name Driver version */
+/*@{*/
+/*! @brief UART driver version 2.1.6. */
+#define FSL_UART_DRIVER_VERSION (MAKE_VERSION(2, 1, 6))
+/*@}*/
+
+/*! @brief Error codes for the UART driver. */
+enum _uart_status
+{
+    kStatus_UART_TxBusy = MAKE_STATUS(kStatusGroup_UART, 0),              /*!< Transmitter is busy. */
+    kStatus_UART_RxBusy = MAKE_STATUS(kStatusGroup_UART, 1),              /*!< Receiver is busy. */
+    kStatus_UART_TxIdle = MAKE_STATUS(kStatusGroup_UART, 2),              /*!< UART transmitter is idle. */
+    kStatus_UART_RxIdle = MAKE_STATUS(kStatusGroup_UART, 3),              /*!< UART receiver is idle. */
+    kStatus_UART_TxWatermarkTooLarge = MAKE_STATUS(kStatusGroup_UART, 4), /*!< TX FIFO watermark too large  */
+    kStatus_UART_RxWatermarkTooLarge = MAKE_STATUS(kStatusGroup_UART, 5), /*!< RX FIFO watermark too large  */
+    kStatus_UART_FlagCannotClearManually =
+        MAKE_STATUS(kStatusGroup_UART, 6),                                /*!< UART flag can't be manually cleared. */
+    kStatus_UART_Error = MAKE_STATUS(kStatusGroup_UART, 7),               /*!< Error happens on UART. */
+    kStatus_UART_RxRingBufferOverrun = MAKE_STATUS(kStatusGroup_UART, 8), /*!< UART RX software ring buffer overrun. */
+    kStatus_UART_RxHardwareOverrun = MAKE_STATUS(kStatusGroup_UART, 9),   /*!< UART RX receiver overrun. */
+    kStatus_UART_NoiseError = MAKE_STATUS(kStatusGroup_UART, 10),         /*!< UART noise error. */
+    kStatus_UART_FramingError = MAKE_STATUS(kStatusGroup_UART, 11),       /*!< UART framing error. */
+    kStatus_UART_ParityError = MAKE_STATUS(kStatusGroup_UART, 12),        /*!< UART parity error. */
+    kStatus_UART_BaudrateNotSupport =
+        MAKE_STATUS(kStatusGroup_UART, 13), /*!< Baudrate is not support in current clock source */
+    kStatus_UART_IdleLineDetected = MAKE_STATUS(kStatusGroup_UART, 14), /*!< UART IDLE line detected. */
+};
+
+/*! @brief UART parity mode. */
+typedef enum _uart_parity_mode
+{
+    kUART_ParityDisabled = 0x0U, /*!< Parity disabled */
+    kUART_ParityEven = 0x2U,     /*!< Parity enabled, type even, bit setting: PE|PT = 10 */
+    kUART_ParityOdd = 0x3U,      /*!< Parity enabled, type odd,  bit setting: PE|PT = 11 */
+} uart_parity_mode_t;
+
+/*! @brief UART stop bit count. */
+typedef enum _uart_stop_bit_count
+{
+    kUART_OneStopBit = 0U, /*!< One stop bit */
+    kUART_TwoStopBit = 1U, /*!< Two stop bits */
+} uart_stop_bit_count_t;
+
+/*! @brief UART idle type select. */
+typedef enum _uart_idle_type_select
+{
+    kUART_IdleTypeStartBit = 0U, /*!< Start counting after a valid start bit. */
+    kUART_IdleTypeStopBit = 1U,  /*!< Start counting after a stop bit. */
+} uart_idle_type_select_t;
+
+/*!
+ * @brief UART interrupt configuration structure, default settings all disabled.
+ *
+ * This structure contains the settings for all of the UART interrupt configurations.
+ */
+enum _uart_interrupt_enable
+{
+#if defined(FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT) && FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT
+    kUART_LinBreakInterruptEnable = (UART_BDH_LBKDIE_MASK), /*!< LIN break detect interrupt. */
+#endif
+    kUART_RxActiveEdgeInterruptEnable = (UART_BDH_RXEDGIE_MASK),   /*!< RX active edge interrupt. */
+    kUART_TxDataRegEmptyInterruptEnable = (UART_C2_TIE_MASK << 8), /*!< Transmit data register empty interrupt. */
+    kUART_TransmissionCompleteInterruptEnable = (UART_C2_TCIE_MASK << 8), /*!< Transmission complete interrupt. */
+    kUART_RxDataRegFullInterruptEnable = (UART_C2_RIE_MASK << 8),         /*!< Receiver data register full interrupt. */
+    kUART_IdleLineInterruptEnable = (UART_C2_ILIE_MASK << 8),             /*!< Idle line interrupt. */
+    kUART_RxOverrunInterruptEnable = (UART_C3_ORIE_MASK << 16),           /*!< Receiver overrun interrupt. */
+    kUART_NoiseErrorInterruptEnable = (UART_C3_NEIE_MASK << 16),          /*!< Noise error flag interrupt. */
+    kUART_FramingErrorInterruptEnable = (UART_C3_FEIE_MASK << 16),        /*!< Framing error flag interrupt. */
+    kUART_ParityErrorInterruptEnable = (UART_C3_PEIE_MASK << 16),         /*!< Parity error flag interrupt. */
+#if defined(FSL_FEATURE_UART_HAS_FIFO) && FSL_FEATURE_UART_HAS_FIFO
+    kUART_RxFifoOverflowInterruptEnable = (UART_CFIFO_RXOFE_MASK << 24),  /*!< RX FIFO overflow interrupt. */
+    kUART_TxFifoOverflowInterruptEnable = (UART_CFIFO_TXOFE_MASK << 24),  /*!< TX FIFO overflow interrupt. */
+    kUART_RxFifoUnderflowInterruptEnable = (UART_CFIFO_RXUFE_MASK << 24), /*!< RX FIFO underflow interrupt. */
+#endif
+    kUART_AllInterruptsEnable =
+#if defined(FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT) && FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT
+        kUART_LinBreakInterruptEnable |
+#endif
+        kUART_RxActiveEdgeInterruptEnable | kUART_TxDataRegEmptyInterruptEnable |
+        kUART_TransmissionCompleteInterruptEnable | kUART_RxDataRegFullInterruptEnable | kUART_IdleLineInterruptEnable |
+        kUART_RxOverrunInterruptEnable | kUART_NoiseErrorInterruptEnable | kUART_FramingErrorInterruptEnable |
+        kUART_ParityErrorInterruptEnable
+#if defined(FSL_FEATURE_UART_HAS_FIFO) && FSL_FEATURE_UART_HAS_FIFO
+        |
+        kUART_RxFifoOverflowInterruptEnable | kUART_TxFifoOverflowInterruptEnable | kUART_RxFifoUnderflowInterruptEnable
+#endif
+    ,
+};
+
+/*!
+ * @brief UART status flags.
+ *
+ * This provides constants for the UART status flags for use in the UART functions.
+ */
+enum _uart_flags
+{
+    kUART_TxDataRegEmptyFlag = (UART_S1_TDRE_MASK),     /*!< TX data register empty flag. */
+    kUART_TransmissionCompleteFlag = (UART_S1_TC_MASK), /*!< Transmission complete flag. */
+    kUART_RxDataRegFullFlag = (UART_S1_RDRF_MASK),      /*!< RX data register full flag. */
+    kUART_IdleLineFlag = (UART_S1_IDLE_MASK),           /*!< Idle line detect flag. */
+    kUART_RxOverrunFlag = (UART_S1_OR_MASK),            /*!< RX overrun flag. */
+    kUART_NoiseErrorFlag = (UART_S1_NF_MASK),           /*!< RX takes 3 samples of each received bit.
+                                                             If any of these samples differ, noise flag sets */
+    kUART_FramingErrorFlag = (UART_S1_FE_MASK),         /*!< Frame error flag, sets if logic 0 was detected
+                                                             where stop bit expected */
+    kUART_ParityErrorFlag = (UART_S1_PF_MASK),          /*!< If parity enabled, sets upon parity error detection */
+#if defined(FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT) && FSL_FEATURE_UART_HAS_LIN_BREAK_DETECT
+    kUART_LinBreakFlag =
+        (UART_S2_LBKDIF_MASK
+         << 8), /*!< LIN break detect interrupt flag, sets when LIN break char detected and LIN circuit enabled */
+#endif
+    kUART_RxActiveEdgeFlag =
+        (UART_S2_RXEDGIF_MASK << 8), /*!< RX pin active edge interrupt flag,sets when active edge detected */
+    kUART_RxActiveFlag =
+        (UART_S2_RAF_MASK << 8), /*!< Receiver Active Flag (RAF), sets at beginning of valid start bit */
+#if defined(FSL_FEATURE_UART_HAS_EXTENDED_DATA_REGISTER_FLAGS) && FSL_FEATURE_UART_HAS_EXTENDED_DATA_REGISTER_FLAGS
+    kUART_NoiseErrorInRxDataRegFlag = (UART_ED_NOISY_MASK << 16),    /*!< Noisy bit, sets if noise detected. */
+    kUART_ParityErrorInRxDataRegFlag = (UART_ED_PARITYE_MASK << 16), /*!< Parity bit, sets if parity error detected. */
+#endif
+#if defined(FSL_FEATURE_UART_HAS_FIFO) && FSL_FEATURE_UART_HAS_FIFO
+    kUART_TxFifoEmptyFlag = (int)(UART_SFIFO_TXEMPT_MASK << 24), /*!< TXEMPT bit, sets if TX buffer is empty */
+    kUART_RxFifoEmptyFlag = (UART_SFIFO_RXEMPT_MASK << 24),      /*!< RXEMPT bit, sets if RX buffer is empty */
+    kUART_TxFifoOverflowFlag = (UART_SFIFO_TXOF_MASK << 24),     /*!< TXOF bit, sets if TX buffer overflow occurred */
+    kUART_RxFifoOverflowFlag = (UART_SFIFO_RXOF_MASK << 24),     /*!< RXOF bit, sets if receive buffer overflow */
+    kUART_RxFifoUnderflowFlag = (UART_SFIFO_RXUF_MASK << 24),    /*!< RXUF bit, sets if receive buffer underflow */
+#endif
+};
+
+/*! @brief UART configuration structure. */
+typedef struct _uart_config
+{
+    uint32_t baudRate_Bps;         /*!< UART baud rate  */
+    uart_parity_mode_t parityMode; /*!< Parity mode, disabled (default), even, odd */
+#if defined(FSL_FEATURE_UART_HAS_STOP_BIT_CONFIG_SUPPORT) && FSL_FEATURE_UART_HAS_STOP_BIT_CONFIG_SUPPORT
+    uart_stop_bit_count_t stopBitCount; /*!< Number of stop bits, 1 stop bit (default) or 2 stop bits  */
+#endif
+#if defined(FSL_FEATURE_UART_HAS_FIFO) && FSL_FEATURE_UART_HAS_FIFO
+    uint8_t txFifoWatermark; /*!< TX FIFO watermark */
+    uint8_t rxFifoWatermark; /*!< RX FIFO watermark */
+#endif
+#if defined(FSL_FEATURE_UART_HAS_MODEM_SUPPORT) && FSL_FEATURE_UART_HAS_MODEM_SUPPORT
+    bool enableRxRTS; /*!< RX RTS enable */
+    bool enableTxCTS; /*!< TX CTS enable */
+#endif
+    uart_idle_type_select_t idleType; /*!< IDLE type select. */
+    bool enableTx;                    /*!< Enable TX */
+    bool enableRx;                    /*!< Enable RX */
+} uart_config_t;
+
+/*! @brief UART transfer structure. */
+typedef struct _uart_transfer
+{
+    uint8_t *data;   /*!< The buffer of data to be transfer.*/
+    size_t dataSize; /*!< The byte count to be transfer. */
+} uart_transfer_t;
+
+/* Forward declaration of the handle typedef. */
+typedef struct _uart_handle uart_handle_t;
+
+/*! @brief UART transfer callback function. */
+typedef void (*uart_transfer_callback_t)(UART_Type *base, uart_handle_t *handle, status_t status, void *userData);
+
+/*! @brief UART handle structure. */
+struct _uart_handle
+{
+    uint8_t *volatile txData;   /*!< Address of remaining data to send. */
+    volatile size_t txDataSize; /*!< Size of the remaining data to send. */
+    size_t txDataSizeAll;       /*!< Size of the data to send out. */
+    uint8_t *volatile rxData;   /*!< Address of remaining data to receive. */
+    volatile size_t rxDataSize; /*!< Size of the remaining data to receive. */
+    size_t rxDataSizeAll;       /*!< Size of the data to receive. */
+
+    uint8_t *rxRingBuffer;              /*!< Start address of the receiver ring buffer. */
+    size_t rxRingBufferSize;            /*!< Size of the ring buffer. */
+    volatile uint16_t rxRingBufferHead; /*!< Index for the driver to store received data into ring buffer. */
+    volatile uint16_t rxRingBufferTail; /*!< Index for the user to get data from the ring buffer. */
+
+    uart_transfer_callback_t callback; /*!< Callback function. */
+    void *userData;                    /*!< UART callback function parameter.*/
+
+    volatile uint8_t txState; /*!< TX transfer state. */
+    volatile uint8_t rxState; /*!< RX transfer state */
+};
+
+/*******************************************************************************
+ * API
+ ******************************************************************************/
+
+#if defined(__cplusplus)
+extern "C" {
+#endif /* _cplusplus */
+
+/*!
+ * @brief Get the UART instance from peripheral base address.
+ *
+ * @param base UART peripheral base address.
+ * @return UART instance.
+ */
+uint32_t UART_GetInstance(UART_Type *base);
+
+/*!
+ * @name Initialization and deinitialization
+ * @{
+ */
+
+/*!
+ * @brief Initializes a UART instance with a user configuration structure and peripheral clock.
+ *
+ * This function configures the UART module with the user-defined settings. The user can configure the configuration
+ * structure and also get the default configuration by using the UART_GetDefaultConfig() function.
+ * The example below shows how to use this API to configure UART.
+ * @code
+ *  uart_config_t uartConfig;
+ *  uartConfig.baudRate_Bps = 115200U;
+ *  uartConfig.parityMode = kUART_ParityDisabled;
+ *  uartConfig.stopBitCount = kUART_OneStopBit;
+ *  uartConfig.txFifoWatermark = 0;
+ *  uartConfig.rxFifoWatermark = 1;
+ *  UART_Init(UART1, &uartConfig, 20000000U);
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @param config Pointer to the user-defined configuration structure.
+ * @param srcClock_Hz UART clock source frequency in HZ.
+ * @retval kStatus_UART_BaudrateNotSupport Baudrate is not support in current clock source.
+ * @retval kStatus_Success Status UART initialize succeed
+ */
+status_t UART_Init(UART_Type *base, const uart_config_t *config, uint32_t srcClock_Hz);
+
+/*!
+ * @brief Deinitializes a UART instance.
+ *
+ * This function waits for TX complete, disables TX and RX, and disables the UART clock.
+ *
+ * @param base UART peripheral base address.
+ */
+void UART_Deinit(UART_Type *base);
+
+/*!
+ * @brief Gets the default configuration structure.
+ *
+ * This function initializes the UART configuration structure to a default value. The default
+ * values are as follows.
+ *   uartConfig->baudRate_Bps = 115200U;
+ *   uartConfig->bitCountPerChar = kUART_8BitsPerChar;
+ *   uartConfig->parityMode = kUART_ParityDisabled;
+ *   uartConfig->stopBitCount = kUART_OneStopBit;
+ *   uartConfig->txFifoWatermark = 0;
+ *   uartConfig->rxFifoWatermark = 1;
+ *   uartConfig->idleType = kUART_IdleTypeStartBit;
+ *   uartConfig->enableTx = false;
+ *   uartConfig->enableRx = false;
+ *
+ * @param config Pointer to configuration structure.
+ */
+void UART_GetDefaultConfig(uart_config_t *config);
+
+/*!
+ * @brief Sets the UART instance baud rate.
+ *
+ * This function configures the UART module baud rate. This function is used to update
+ * the UART module baud rate after the UART module is initialized by the UART_Init.
+ * @code
+ *  UART_SetBaudRate(UART1, 115200U, 20000000U);
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @param baudRate_Bps UART baudrate to be set.
+ * @param srcClock_Hz UART clock source freqency in Hz.
+ * @retval kStatus_UART_BaudrateNotSupport Baudrate is not support in the current clock source.
+ * @retval kStatus_Success Set baudrate succeeded.
+ */
+status_t UART_SetBaudRate(UART_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz);
+
+/* @} */
+
+/*!
+ * @name Status
+ * @{
+ */
+
+/*!
+ * @brief Gets UART status flags.
+ *
+ * This function gets all UART status flags. The flags are returned as the logical
+ * OR value of the enumerators @ref _uart_flags. To check a specific status,
+ * compare the return value with enumerators in @ref _uart_flags.
+ * For example, to check whether the TX is empty, do the following.
+ * @code
+ *     if (kUART_TxDataRegEmptyFlag & UART_GetStatusFlags(UART1))
+ *     {
+ *         ...
+ *     }
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @return UART status flags which are ORed by the enumerators in the _uart_flags.
+ */
+uint32_t UART_GetStatusFlags(UART_Type *base);
+
+/*!
+ * @brief Clears status flags with the provided mask.
+ *
+ * This function clears UART status flags with a provided mask. An automatically cleared flag
+ * can't be cleared by this function.
+ * These flags can only be cleared or set by hardware.
+ *    kUART_TxDataRegEmptyFlag, kUART_TransmissionCompleteFlag, kUART_RxDataRegFullFlag,
+ *    kUART_RxActiveFlag, kUART_NoiseErrorInRxDataRegFlag, kUART_ParityErrorInRxDataRegFlag,
+ *    kUART_TxFifoEmptyFlag,kUART_RxFifoEmptyFlag
+ * Note that this API should be called when the Tx/Rx is idle. Otherwise it has no effect.
+ *
+ * @param base UART peripheral base address.
+ * @param mask The status flags to be cleared; it is logical OR value of @ref _uart_flags.
+ * @retval kStatus_UART_FlagCannotClearManually The flag can't be cleared by this function but
+ *         it is cleared automatically by hardware.
+ * @retval kStatus_Success Status in the mask is cleared.
+ */
+status_t UART_ClearStatusFlags(UART_Type *base, uint32_t mask);
+
+/* @} */
+
+/*!
+ * @name Interrupts
+ * @{
+ */
+
+/*!
+ * @brief Enables UART interrupts according to the provided mask.
+ *
+ * This function enables the UART interrupts according to the provided mask. The mask
+ * is a logical OR of enumeration members. See @ref _uart_interrupt_enable.
+ * For example, to enable TX empty interrupt and RX full interrupt, do the following.
+ * @code
+ *     UART_EnableInterrupts(UART1,kUART_TxDataRegEmptyInterruptEnable | kUART_RxDataRegFullInterruptEnable);
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @param mask The interrupts to enable. Logical OR of @ref _uart_interrupt_enable.
+ */
+void UART_EnableInterrupts(UART_Type *base, uint32_t mask);
+
+/*!
+ * @brief Disables the UART interrupts according to the provided mask.
+ *
+ * This function disables the UART interrupts according to the provided mask. The mask
+ * is a logical OR of enumeration members. See @ref _uart_interrupt_enable.
+ * For example, to disable TX empty interrupt and RX full interrupt do the following.
+ * @code
+ *     UART_DisableInterrupts(UART1,kUART_TxDataRegEmptyInterruptEnable | kUART_RxDataRegFullInterruptEnable);
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @param mask The interrupts to disable. Logical OR of @ref _uart_interrupt_enable.
+ */
+void UART_DisableInterrupts(UART_Type *base, uint32_t mask);
+
+/*!
+ * @brief Gets the enabled UART interrupts.
+ *
+ * This function gets the enabled UART interrupts. The enabled interrupts are returned
+ * as the logical OR value of the enumerators @ref _uart_interrupt_enable. To check
+ * a specific interrupts enable status, compare the return value with enumerators
+ * in @ref _uart_interrupt_enable.
+ * For example, to check whether TX empty interrupt is enabled, do the following.
+ * @code
+ *     uint32_t enabledInterrupts = UART_GetEnabledInterrupts(UART1);
+ *
+ *     if (kUART_TxDataRegEmptyInterruptEnable & enabledInterrupts)
+ *     {
+ *         ...
+ *     }
+ * @endcode
+ *
+ * @param base UART peripheral base address.
+ * @return UART interrupt flags which are logical OR of the enumerators in @ref _uart_interrupt_enable.
+ */
+uint32_t UART_GetEnabledInterrupts(UART_Type *base);
+
+/* @} */
+
+#if defined(FSL_FEATURE_UART_HAS_DMA_SELECT) && FSL_FEATURE_UART_HAS_DMA_SELECT
+/*!
+ * @name DMA Control
+ * @{
+ */
+
+/*!
+ * @brief Gets the UART data register address.
+ *
+ * This function returns the UART data register address, which is mainly used by DMA/eDMA.
+ *
+ * @param base UART peripheral base address.
+ * @return UART data register addresses which are used both by the transmitter and the receiver.
+ */
+static inline uint32_t UART_GetDataRegisterAddress(UART_Type *base)
+{
+    return (uint32_t) & (base->D);
+}
+
+/*!
+ * @brief Enables or disables the UART transmitter DMA request.
+ *
+ * This function enables or disables the transmit data register empty flag, S1[TDRE], to generate the DMA requests.
+ *
+ * @param base UART peripheral base address.
+ * @param enable True to enable, false to disable.
+ */
+static inline void UART_EnableTxDMA(UART_Type *base, bool enable)
+{
+    if (enable)
+    {
+#if (defined(FSL_FEATURE_UART_IS_SCI) && FSL_FEATURE_UART_IS_SCI)
+        base->C4 |= UART_C4_TDMAS_MASK;
+#else
+        base->C5 |= UART_C5_TDMAS_MASK;
+#endif
+        base->C2 |= UART_C2_TIE_MASK;
+    }
+    else
+    {
+#if (defined(FSL_FEATURE_UART_IS_SCI) && FSL_FEATURE_UART_IS_SCI)
+        base->C4 &= ~UART_C4_TDMAS_MASK;
+#else
+        base->C5 &= ~UART_C5_TDMAS_MASK;
+#endif
+        base->C2 &= ~UART_C2_TIE_MASK;
+    }
+}
+
+/*!
+ * @brief Enables or disables the UART receiver DMA.
+ *
+ * This function enables or disables the receiver data register full flag, S1[RDRF], to generate DMA requests.
+ *
+ * @param base UART peripheral base address.
+ * @param enable True to enable, false to disable.
+ */
+static inline void UART_EnableRxDMA(UART_Type *base, bool enable)
+{
+    if (enable)
+    {
+#if (defined(FSL_FEATURE_UART_IS_SCI) && FSL_FEATURE_UART_IS_SCI)
+        base->C4 |= UART_C4_RDMAS_MASK;
+#else
+        base->C5 |= UART_C5_RDMAS_MASK;
+#endif
+        base->C2 |= UART_C2_RIE_MASK;
+    }
+    else
+    {
+#if (defined(FSL_FEATURE_UART_IS_SCI) && FSL_FEATURE_UART_IS_SCI)
+        base->C4 &= ~UART_C4_RDMAS_MASK;
+#else
+        base->C5 &= ~UART_C5_RDMAS_MASK;
+#endif
+        base->C2 &= ~UART_C2_RIE_MASK;
+    }
+}
+
+/* @} */
+#endif /* FSL_FEATURE_UART_HAS_DMA_SELECT */
+
+/*!
+ * @name Bus Operations
+ * @{
+ */
+
+/*!
+ * @brief Enables or disables the UART transmitter.
+ *
+ * This function enables or disables the UART transmitter.
+ *
+ * @param base UART peripheral base address.
+ * @param enable True to enable, false to disable.
+ */
+static inline void UART_EnableTx(UART_Type *base, bool enable)
+{
+    if (enable)
+    {
+        base->C2 |= UART_C2_TE_MASK;
+    }
+    else
+    {
+        base->C2 &= ~UART_C2_TE_MASK;
+    }
+}
+
+/*!
+ * @brief Enables or disables the UART receiver.
+ *
+ * This function enables or disables the UART receiver.
+ *
+ * @param base UART peripheral base address.
+ * @param enable True to enable, false to disable.
+ */
+static inline void UART_EnableRx(UART_Type *base, bool enable)
+{
+    if (enable)
+    {
+        base->C2 |= UART_C2_RE_MASK;
+    }
+    else
+    {
+        base->C2 &= ~UART_C2_RE_MASK;
+    }
+}
+
+/*!
+ * @brief Writes to the TX register.
+ *
+ * This function writes data to the TX register directly. The upper layer must ensure
+ * that the TX register is empty or TX FIFO has empty room before calling this function.
+ *
+ * @param base UART peripheral base address.
+ * @param data The byte to write.
+ */
+static inline void UART_WriteByte(UART_Type *base, uint8_t data)
+{
+    base->D = data;
+}
+
+/*!
+ * @brief Reads the RX register directly.
+ *
+ * This function reads data from the RX register directly. The upper layer must
+ * ensure that the RX register is full or that the TX FIFO has data before calling this function.
+ *
+ * @param base UART peripheral base address.
+ * @return The byte read from UART data register.
+ */
+static inline uint8_t UART_ReadByte(UART_Type *base)
+{
+    return base->D;
+}
+
+/*!
+ * @brief Writes to the TX register using a blocking method.
+ *
+ * This function polls the TX register, waits for the TX register to be empty or for the TX FIFO
+ * to have room and writes data to the TX buffer.
+ *
+ * @note This function does not check whether all data is sent out to the bus.
+ * Before disabling the TX, check kUART_TransmissionCompleteFlag to ensure that the TX is
+ * finished.
+ *
+ * @param base UART peripheral base address.
+ * @param data Start address of the data to write.
+ * @param length Size of the data to write.
+ */
+void UART_WriteBlocking(UART_Type *base, const uint8_t *data, size_t length);
+
+/*!
+ * @brief Read RX data register using a blocking method.
+ *
+ * This function polls the RX register, waits for the RX register to be full or for RX FIFO to
+ * have data, and reads data from the TX register.
+ *
+ * @param base UART peripheral base address.
+ * @param data Start address of the buffer to store the received data.
+ * @param length Size of the buffer.
+ * @retval kStatus_UART_RxHardwareOverrun Receiver overrun occurred while receiving data.
+ * @retval kStatus_UART_NoiseError A noise error occurred while receiving data.
+ * @retval kStatus_UART_FramingError A framing error occurred while receiving data.
+ * @retval kStatus_UART_ParityError A parity error occurred while receiving data.
+ * @retval kStatus_Success Successfully received all data.
+ */
+status_t UART_ReadBlocking(UART_Type *base, uint8_t *data, size_t length);
+
+/* @} */
+
+/*!
+ * @name Transactional
+ * @{
+ */
+
+/*!
+ * @brief Initializes the UART handle.
+ *
+ * This function initializes the UART handle which can be used for other UART
+ * transactional APIs. Usually, for a specified UART instance,
+ * call this API once to get the initialized handle.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param callback The callback function.
+ * @param userData The parameter of the callback function.
+ */
+void UART_TransferCreateHandle(UART_Type *base,
+                               uart_handle_t *handle,
+                               uart_transfer_callback_t callback,
+                               void *userData);
+
+/*!
+ * @brief Sets up the RX ring buffer.
+ *
+ * This function sets up the RX ring buffer to a specific UART handle.
+ *
+ * When the RX ring buffer is used, data received are stored into the ring buffer even when the
+ * user doesn't call the UART_TransferReceiveNonBlocking() API. If data is already received
+ * in the ring buffer, the user can get the received data from the ring buffer directly.
+ *
+ * @note When using the RX ring buffer, one byte is reserved for internal use. In other
+ * words, if @p ringBufferSize is 32, only 31 bytes are used for saving data.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param ringBuffer Start address of the ring buffer for background receiving. Pass NULL to disable the ring buffer.
+ * @param ringBufferSize Size of the ring buffer.
+ */
+void UART_TransferStartRingBuffer(UART_Type *base, uart_handle_t *handle, uint8_t *ringBuffer, size_t ringBufferSize);
+
+/*!
+ * @brief Aborts the background transfer and uninstalls the ring buffer.
+ *
+ * This function aborts the background transfer and uninstalls the ring buffer.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ */
+void UART_TransferStopRingBuffer(UART_Type *base, uart_handle_t *handle);
+
+/*!
+ * @brief Get the length of received data in RX ring buffer.
+ *
+ * @param handle UART handle pointer.
+ * @return Length of received data in RX ring buffer.
+ */
+size_t UART_TransferGetRxRingBufferLength(uart_handle_t *handle);
+
+/*!
+ * @brief Transmits a buffer of data using the interrupt method.
+ *
+ * This function sends data using an interrupt method. This is a non-blocking function, which
+ * returns directly without waiting for all data to be written to the TX register. When
+ * all data is written to the TX register in the ISR, the UART driver calls the callback
+ * function and passes the @ref kStatus_UART_TxIdle as status parameter.
+ *
+ * @note The kStatus_UART_TxIdle is passed to the upper layer when all data is written
+ * to the TX register. However, it does not ensure that all data is sent out. Before disabling the TX,
+ * check the kUART_TransmissionCompleteFlag to ensure that the TX is finished.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param xfer UART transfer structure. See  #uart_transfer_t.
+ * @retval kStatus_Success Successfully start the data transmission.
+ * @retval kStatus_UART_TxBusy Previous transmission still not finished; data not all written to TX register yet.
+ * @retval kStatus_InvalidArgument Invalid argument.
+ */
+status_t UART_TransferSendNonBlocking(UART_Type *base, uart_handle_t *handle, uart_transfer_t *xfer);
+
+/*!
+ * @brief Aborts the interrupt-driven data transmit.
+ *
+ * This function aborts the interrupt-driven data sending. The user can get the remainBytes to find out
+ * how many bytes are not sent out.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ */
+void UART_TransferAbortSend(UART_Type *base, uart_handle_t *handle);
+
+/*!
+ * @brief Gets the number of bytes written to the UART TX register.
+ *
+ * This function gets the number of bytes written to the UART TX
+ * register by using the interrupt method.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param count Send bytes count.
+ * @retval kStatus_NoTransferInProgress No send in progress.
+ * @retval kStatus_InvalidArgument The parameter is invalid.
+ * @retval kStatus_Success Get successfully through the parameter \p count;
+ */
+status_t UART_TransferGetSendCount(UART_Type *base, uart_handle_t *handle, uint32_t *count);
+
+/*!
+ * @brief Receives a buffer of data using an interrupt method.
+ *
+ * This function receives data using an interrupt method. This is a non-blocking function, which
+ *  returns without waiting for all data to be received.
+ * If the RX ring buffer is used and not empty, the data in the ring buffer is copied and
+ * the parameter @p receivedBytes shows how many bytes are copied from the ring buffer.
+ * After copying, if the data in the ring buffer is not enough to read, the receive
+ * request is saved by the UART driver. When the new data arrives, the receive request
+ * is serviced first. When all data is received, the UART driver notifies the upper layer
+ * through a callback function and passes the status parameter @ref kStatus_UART_RxIdle.
+ * For example, the upper layer needs 10 bytes but there are only 5 bytes in the ring buffer.
+ * The 5 bytes are copied to the xfer->data and this function returns with the
+ * parameter @p receivedBytes set to 5. For the left 5 bytes, newly arrived data is
+ * saved from the xfer->data[5]. When 5 bytes are received, the UART driver notifies the upper layer.
+ * If the RX ring buffer is not enabled, this function enables the RX and RX interrupt
+ * to receive data to the xfer->data. When all data is received, the upper layer is notified.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param xfer UART transfer structure, see #uart_transfer_t.
+ * @param receivedBytes Bytes received from the ring buffer directly.
+ * @retval kStatus_Success Successfully queue the transfer into transmit queue.
+ * @retval kStatus_UART_RxBusy Previous receive request is not finished.
+ * @retval kStatus_InvalidArgument Invalid argument.
+ */
+status_t UART_TransferReceiveNonBlocking(UART_Type *base,
+                                         uart_handle_t *handle,
+                                         uart_transfer_t *xfer,
+                                         size_t *receivedBytes);
+
+/*!
+ * @brief Aborts the interrupt-driven data receiving.
+ *
+ * This function aborts the interrupt-driven data receiving. The user can get the remainBytes to know
+ * how many bytes are not received yet.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ */
+void UART_TransferAbortReceive(UART_Type *base, uart_handle_t *handle);
+
+/*!
+ * @brief Gets the number of bytes that have been received.
+ *
+ * This function gets the number of bytes that have been received.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ * @param count Receive bytes count.
+ * @retval kStatus_NoTransferInProgress No receive in progress.
+ * @retval kStatus_InvalidArgument Parameter is invalid.
+ * @retval kStatus_Success Get successfully through the parameter \p count;
+ */
+status_t UART_TransferGetReceiveCount(UART_Type *base, uart_handle_t *handle, uint32_t *count);
+
+/*!
+ * @brief UART IRQ handle function.
+ *
+ * This function handles the UART transmit and receive IRQ request.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ */
+void UART_TransferHandleIRQ(UART_Type *base, uart_handle_t *handle);
+
+/*!
+ * @brief UART Error IRQ handle function.
+ *
+ * This function handles the UART error IRQ request.
+ *
+ * @param base UART peripheral base address.
+ * @param handle UART handle pointer.
+ */
+void UART_TransferHandleErrorIRQ(UART_Type *base, uart_handle_t *handle);
+
+/* @} */
+
+#if defined(__cplusplus)
+}
+#endif
+
+/*! @}*/
+
+#endif /* _FSL_UART_H_ */