雄介 太田
mbed(SerialHalfDuplex入り)
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_L053R8/stm32l0xx_hal_comp.h
- Revision:
- 84:0b3ab51c8877
- Child:
- 92:4fc01daae5a5
diff -r 8a40adfe8776 -r 0b3ab51c8877 TARGET_NUCLEO_L053R8/stm32l0xx_hal_comp.h
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUCLEO_L053R8/stm32l0xx_hal_comp.h Mon May 19 18:14:09 2014 +0100
@@ -0,0 +1,411 @@
+/**
+ ******************************************************************************
+ * @file stm32l0xx_hal_comp.h
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 22-April-2014
+ * @brief Header file of COMP HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_COMP_H
+#define __STM32L0xx_HAL_COMP_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup COMP
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+ * @brief COMP Init structure definition
+ */
+
+typedef struct
+{
+
+ uint32_t InvertingInput; /*!< Selects the inverting input of the comparator.
+ This parameter can be a value of @ref COMP_InvertingInput */
+
+ uint32_t NonInvertingInput; /*!< Selects the non inverting input of the comparator.
+ This parameter can be a value of @ref COMP_NonInvertingInput */
+
+ uint32_t OutputPol; /*!< Selects the output polarity of the comparator.
+ This parameter can be a value of @ref COMP_OutputPolarity */
+
+ uint32_t Mode; /*!< Selects the operating comsumption mode of the comparator
+ to adjust the speed/consumption.
+ This parameter can be a value of @ref COMP_Mode */
+
+ uint32_t WindowMode; /*!< Selects the window mode of the comparator 2.
+ This parameter can be a value of @ref COMP_WindowMode */
+
+ uint32_t TriggerMode; /*!< Selects the trigger mode of the comparator (interrupt mode).
+ This parameter can be a value of @ref COMP_TriggerMode */
+
+}COMP_InitTypeDef;
+
+/**
+ * @brief HAL State structures definition
+ */
+typedef enum
+{
+ HAL_COMP_STATE_RESET = 0x00, /*!< COMP not yet initialized or disabled */
+ HAL_COMP_STATE_READY = 0x01, /*!< COMP initialized and ready for use */
+ HAL_COMP_STATE_READY_LOCKED = 0x11, /*!< COMP initialized but the configuration is locked */
+ HAL_COMP_STATE_BUSY = 0x02, /*!< COMP is running */
+ HAL_COMP_STATE_BUSY_LOCKED = 0x12 /*!< COMP is running and the configuration is locked */
+}HAL_COMP_StateTypeDef;
+
+/**
+ * @brief PPP Handle Structure definition
+ */
+typedef struct
+{
+ COMP_TypeDef *Instance; /*!< Register base address */
+ COMP_InitTypeDef Init; /*!< COMP required parameters */
+ HAL_LockTypeDef Lock; /*!< Locking object */
+ __IO HAL_COMP_StateTypeDef State; /*!< COMP communication state */
+} COMP_HandleTypeDef;
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup COMP_Exported_Constants
+ * @{
+ */
+
+/** @defgroup COMP_OutputPolarity
+ * @{
+ */
+#define COMP_OUTPUTPOL_NONINVERTED ((uint32_t)0x00000000) /*!< COMP output on GPIO isn't inverted */
+#define COMP_OUTPUTPOL_INVERTED COMP_CSR_COMPxPOLARITY /*!< COMP output on GPIO is inverted */
+#define IS_COMP_OUTPUTPOL(POL) (((POL) == COMP_OUTPUTPOL_NONINVERTED) || \
+ ((POL) == COMP_OUTPUTPOL_INVERTED))
+/**
+ * @}
+ */
+
+
+/** @defgroup COMP_InvertingInput
+ * @{
+ */
+
+/* Inverting Input specific to COMP1 */
+#define COMP_INVERTINGINPUT_VREFINT ((uint32_t)0x00000000) /*!< VREFINT connected to comparator1 inverting input */
+#define COMP_INVERTINGINPUT_IO1 ((uint32_t)0x00000010) /*!< I/O1 connected to comparator inverting input (PA0) for COMP1 and (PA2) for COMP2*/
+#define COMP_INVERTINGINPUT_DAC1 ((uint32_t)0x00000020) /*!< DAC1_OUT (PA4) connected to comparator inverting input */
+#define COMP_INVERTINGINPUT_IO2 ((uint32_t)0x00000030) /*!< I/O2 (PA5) connected to comparator inverting input */
+
+/* Inverting Input specific to COMP2 */
+#define COMP_INVERTINGINPUT_1_4VREFINT ((uint32_t)0x00000040) /*!< 1/4 VREFINT connected to comparator inverting input */
+#define COMP_INVERTINGINPUT_1_2VREFINT ((uint32_t)0x00000050) /*!< 1/2 VREFINT connected to comparator inverting input */
+#define COMP_INVERTINGINPUT_3_4VREFINT ((uint32_t)0x00000060) /*!< 3/4 VREFINT connected to comparator inverting input */
+#define COMP_INVERTINGINPUT_IO3 ((uint32_t)0x00000070) /*!< I/O3 (PB3) for COMP2 connected to comparator inverting input */
+
+
+#define IS_COMP_INVERTINGINPUT(INPUT) (((INPUT) == COMP_INVERTINGINPUT_VREFINT) || \
+ ((INPUT) == COMP_INVERTINGINPUT_IO1) || \
+ ((INPUT) == COMP_INVERTINGINPUT_DAC1) || \
+ ((INPUT) == COMP_INVERTINGINPUT_IO2) || \
+ ((INPUT) == COMP_INVERTINGINPUT_1_4VREFINT) || \
+ ((INPUT) == COMP_INVERTINGINPUT_1_2VREFINT) || \
+ ((INPUT) == COMP_INVERTINGINPUT_3_4VREFINT) || \
+ ((INPUT) == COMP_INVERTINGINPUT_IO3))
+
+/**
+ * @}
+ */
+
+
+/** @defgroup COMP_NonInvertingInput
+ * @{
+ */
+
+#define COMP_NONINVERTINGINPUT_IO1 ((uint32_t)0x00000000) /*!< I/O1 (PA3) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO2 ((uint32_t)0x00000100) /*!< I/O2 (PB4) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO3 ((uint32_t)0x00000200) /*!< I/O3 (PB5) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO4 ((uint32_t)0x00000300) /*!< I/O1 (PB6) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO5 ((uint32_t)0x00000400) /*!< I/O3 (PB7) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO6 ((uint32_t)0x00000500) /*!< I/O3 (PB7) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO7 ((uint32_t)0x00000600) /*!< I/O3 (PB7) connected to comparator non inverting input */
+#define COMP_NONINVERTINGINPUT_IO8 ((uint32_t)0x00000700) /*!< I/O3 (PB7) connected to comparator non inverting input */
+
+#define IS_COMP_NONINVERTINGINPUT(INPUT) (((INPUT) == COMP_NONINVERTINGINPUT_IO1) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO2) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO3) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO4) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO5) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO6) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO7) || \
+ ((INPUT) == COMP_NONINVERTINGINPUT_IO8))
+/**
+ * @}
+ */
+
+
+/** @defgroup COMP_Mode
+ * @{
+ */
+/* Please refer to the electrical characteristics in the device datasheet for
+ the power consumption values */
+#define COMP_MODE_HIGHSPEED COMP_CSR_COMP2SPEED /*!< High Speed */
+#define COMP_MODE_LOWSPEED ((uint32_t)0x00000000) /*!< Low Speed */
+
+#define IS_COMP_MODE(SPEED) (((SPEED) == COMP_MODE_HIGHSPEED) || \
+ ((SPEED) == COMP_MODE_LOWSPEED))
+/**
+ * @}
+ */
+
+/** @defgroup COMP_WindowMode
+ * @{
+ */
+#define COMP_WINDOWMODE_DISABLED ((uint32_t)0x00000000) /*!< Window mode disabled (Plus input of comparator 1 connected to PA1)*/
+#define COMP_WINDOWMODE_ENABLED COMP_CSR_COMP1WM /*!< Window mode enabled: Plus input of comparator 1 shorted with Plus input of comparator 2 */
+#define IS_COMP_WINDOWMODE(WINDOWMODE) (((WINDOWMODE) == COMP_WINDOWMODE_DISABLED) || \
+ ((WINDOWMODE) == COMP_WINDOWMODE_ENABLED))
+
+#define IS_COMP_WINDOWMODE_INSTANCE(INSTANCE) ((INSTANCE) == COMP1)
+/**
+ * @}
+ */
+
+
+/** @defgroup COMP_OutputLevel
+ * @{
+ */
+/* When output polarity is not inverted, comparator output is low when
+ the non-inverting input is at a lower voltage than the inverting input*/
+#define COMP_OUTPUTLEVEL_LOW ((uint32_t)0x00000000)
+/* When output polarity is not inverted, comparator output is high when
+ the non-inverting input is at a higher voltage than the inverting input */
+#define COMP_OUTPUTLEVEL_HIGH COMP_CSR_COMPxOUTVALUE
+/**
+ * @}
+ */
+
+/* CSR register Mask */
+#define COMP_CSR_UPDATE_PARAMETERS_MASK ((uint32_t)0xC0008779)
+
+#define COMP_LOCK_DISABLE ((uint32_t)0x00000000)
+#define COMP_LOCK_ENABLE COMP_CSR_COMPxLOCK
+
+#define COMP_STATE_BIT_LOCK ((uint32_t)0x10)
+
+/** @defgroup COMP_TriggerMode
+ * @{
+ */
+#define COMP_TRIGGERMODE_IT_RISING ((uint32_t)0x00000001) /*!< External Interrupt Mode with Rising edge trigger detection */
+#define COMP_TRIGGERMODE_IT_FALLING ((uint32_t)0x00000002) /*!< External Interrupt Mode with Falling edge trigger detection */
+#define COMP_TRIGGERMODE_IT_RISING_FALLING ((uint32_t)0x00000003) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define IS_COMP_TRIGGERMODE(MODE) (((MODE) == COMP_TRIGGERMODE_IT_RISING) || \
+ ((MODE) == COMP_TRIGGERMODE_IT_FALLING) || \
+ ((MODE) == COMP_TRIGGERMODE_IT_RISING_FALLING))
+/**
+ * @}
+ */
+
+/** @defgroup COMP_ExtiLineEvent
+ * @{
+ */
+
+#define COMP_EXTI_LINE_COMP2_EVENT ((uint32_t)0x00400000) /*!< External interrupt line 22 Connected to COMP2 */
+#define COMP_EXTI_LINE_COMP1_EVENT ((uint32_t)0x00200000) /*!< External interrupt line 21 Connected to COMP1 */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @brief Reset COMP handle state
+ * @param __HANDLE__: COMP handle.
+ * @retval None
+ */
+#define __HAL_COMP_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_COMP_STATE_RESET)
+
+/**
+ * @brief Enables the specified comparator
+ * @param __HANDLE__: COMP handle.
+ * @retval None.
+ */
+#define __HAL_COMP_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CSR |= (COMP_CSR_COMPxEN))
+
+/**
+ * @brief Disables the specified comparator
+ * @param __HANDLE__: COMP handle.
+ * @retval None.
+ */
+#define __HAL_COMP_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CSR &= ~(COMP_CSR_COMPxEN))
+
+/**
+ * @brief Lock the specified comparator configuration
+ * @param __HANDLE__: COMP handle.
+ * @retval None.
+ */
+#define __HAL_COMP_LOCK(__HANDLE__) ((__HANDLE__)->Instance->CSR |= COMP_CSR_COMPxLOCK)
+
+/** @brief Checks whether the specified COMP flag is set or not.
+ * @param __HANDLE__: specifies the COMP Handle.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg COMP_FLAG_LOCK: lock flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_COMP_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->CSR & (__FLAG__)) == (__FLAG__))
+
+
+/**
+ * @brief Enable the Exti Line rising edge trigger.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be enabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_RISING_IT_ENABLE(__EXTILINE__) (EXTI->RTSR |= (__EXTILINE__))
+
+/**
+ * @brief Disable the Exti Line rising edge trigger.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be disabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_RISING_IT_DISABLE(__EXTILINE__) (EXTI->RTSR &= ~(__EXTILINE__))
+
+/**
+ * @brief Enable the Exti Line falling edge trigger.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be enabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_FALLING_IT_ENABLE(__EXTILINE__) (EXTI->FTSR |= (__EXTILINE__))
+
+/**
+ * @brief Disable the Exti Line falling edge trigger.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be disabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_FALLING_IT_DISABLE(__EXTILINE__) (EXTI->FTSR &= ~(__EXTILINE__))
+
+/**
+ * @brief Get the specified EXTI line for a comparator instance
+ * @param __INSTANCE__: specifies the COMP instance.
+ * @retval value of @ref COMP_ExtiLineEvent
+ */
+#define __HAL_COMP_GET_EXTI_LINE(__INSTANCE__) (((__INSTANCE__) == COMP1) ? COMP_EXTI_LINE_COMP1_EVENT : \
+ COMP_EXTI_LINE_COMP2_EVENT)
+
+/**
+ * @brief Enable the COMP Exti Line.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be enabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_ENABLE_IT(__EXTILINE__) (EXTI->IMR |= (__EXTILINE__))
+
+/**
+ * @brief Disable the COMP Exti Line.
+ * @param __EXTILINE__: specifies the COMP Exti sources to be disabled.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_DISABLE_IT(__EXTILINE__) (EXTI->IMR &= ~(__EXTILINE__))
+
+/**
+ * @brief Checks whether the specified EXTI line flag is set or not.
+ * @param __FLAG__: specifies the COMP Exti sources to be checked.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval The state of __FLAG__ (SET or RESET).
+ */
+#define __HAL_COMP_EXTI_GET_FLAG(__FLAG__) (EXTI->PR & (__FLAG__))
+
+/**
+ * @brief Clear the COMP Exti flags.
+ * @param __FLAG__: specifies the COMP Exti sources to be cleared.
+ * This parameter can be a value of @ref COMP_ExtiLineEvent
+ * @retval None.
+ */
+#define __HAL_COMP_EXTI_CLEAR_FLAG(__FLAG__) (EXTI->PR |= (__FLAG__))
+
+
+/* Exported functions --------------------------------------------------------*/
+
+/* Initialization/de-initialization functions **********************************/
+HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp);
+HAL_StatusTypeDef HAL_COMP_DeInit (COMP_HandleTypeDef *hcomp);
+void HAL_COMP_MspInit(COMP_HandleTypeDef *hcomp);
+void HAL_COMP_MspDeInit(COMP_HandleTypeDef *hcomp);
+
+/* I/O operation functions *****************************************************/
+HAL_StatusTypeDef HAL_COMP_Start(COMP_HandleTypeDef *hcomp);
+HAL_StatusTypeDef HAL_COMP_Stop(COMP_HandleTypeDef *hcomp);
+HAL_StatusTypeDef HAL_COMP_Start_IT(COMP_HandleTypeDef *hcomp);
+HAL_StatusTypeDef HAL_COMP_Stop_IT(COMP_HandleTypeDef *hcomp);
+void HAL_COMP_IRQHandler(COMP_HandleTypeDef *hcomp);
+
+/* Peripheral Control functions ************************************************/
+HAL_StatusTypeDef HAL_COMP_Lock(COMP_HandleTypeDef *hcomp);
+uint32_t HAL_COMP_GetOutputLevel(COMP_HandleTypeDef *hcomp);
+
+/* Callback in Interrupt mode */
+void HAL_COMP_TriggerCallback(COMP_HandleTypeDef *hcomp);
+
+/* Peripheral State functions **************************************************/
+HAL_COMP_StateTypeDef HAL_COMP_GetState(COMP_HandleTypeDef *hcomp);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_COMP_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/