雄介 太田
mbed(SerialHalfDuplex入り)
Fork of
mbed
by 
mbed official
TARGET_NUCLEO_F103RB/stm32f1xx_hal_rcc.h
- Committer:
- Kojto
- Date:
- 2015-03-17
- Revision:
- 96:487b796308b0
File content as of revision 96:487b796308b0:
/**
******************************************************************************
* @file stm32f1xx_hal_rcc.h
* @author MCD Application Team
* @version V1.0.0
* @date 15-December-2014
* @brief Header file of RCC HAL module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F1xx_HAL_RCC_H
#define __STM32F1xx_HAL_RCC_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal_def.h"
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
/** @addtogroup RCC
* @{
*/
/** @addtogroup RCC_Private_Constants
* @{
*/
#define RCC_DBP_TIMEOUT_VALUE ((uint32_t)100)
#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT
#define CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000) /* 5 s */
#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT
#define HSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
#define LSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
#define PLL_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
#define LSI_VALUE ((uint32_t)40000) /* 40kHz */
/** @defgroup RCC_BitAddress_AliasRegion BitAddress AliasRegion
* @brief RCC registers bit address in the alias region
* @{
*/
#define RCC_OFFSET (RCC_BASE - PERIPH_BASE)
#define RCC_CR_OFFSET 0x00
#define RCC_CFGR_OFFSET 0x04
#define RCC_CIR_OFFSET 0x08
#define RCC_BDCR_OFFSET 0x20
#define RCC_CSR_OFFSET 0x24
#define RCC_CR_OFFSET_BB (RCC_OFFSET + RCC_CR_OFFSET)
#define RCC_CFGR_OFFSET_BB (RCC_OFFSET + RCC_CFGR_OFFSET)
#define RCC_CIR_OFFSET_BB (RCC_OFFSET + RCC_CIR_OFFSET)
#define RCC_BDCR_OFFSET_BB (RCC_OFFSET + RCC_BDCR_OFFSET)
#define RCC_CSR_OFFSET_BB (RCC_OFFSET + RCC_CSR_OFFSET)
/* --- CR Register ---*/
/* Alias word address of HSION bit */
#define HSION_BITNUMBER POSITION_VAL(RCC_CR_HSION)
#define RCC_CR_HSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (HSION_BITNUMBER * 4)))
/* Alias word address of HSEON bit */
#define HSEON_BITNUMBER POSITION_VAL(RCC_CR_HSEON)
#define CR_HSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (HSEON_BITNUMBER * 4)))
/* Alias word address of CSSON bit */
#define CSSON_BITNUMBER POSITION_VAL(RCC_CR_CSSON)
#define RCC_CR_CSSON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (CSSON_BITNUMBER * 4)))
/* Alias word address of PLLON bit */
#define PLLON_BITNUMBER POSITION_VAL(RCC_CR_PLLON)
#define RCC_CR_PLLON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (PLLON_BITNUMBER * 4)))
/* --- CSR Register ---*/
/* Alias word address of LSION bit */
#define LSION_BITNUMBER POSITION_VAL(RCC_CSR_LSION)
#define RCC_CSR_LSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CSR_OFFSET_BB * 32) + (LSION_BITNUMBER * 4)))
/* --- BDCR Register ---*/
/* Alias word address of LSEON bit */
#define LSEON_BITNUMBER POSITION_VAL(RCC_BDCR_LSEON)
#define BDCR_LSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (LSEON_BITNUMBER * 4)))
/* Alias word address of LSEON bit */
#define LSEBYP_BITNUMBER POSITION_VAL(RCC_BDCR_LSEBYP)
#define BDCR_LSEBYP_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (LSEBYP_BITNUMBER * 4)))
/* Alias word address of RTCEN bit */
#define RTCEN_BITNUMBER POSITION_VAL(RCC_BDCR_RTCEN)
#define RCC_BDCR_RTCEN_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (RTCEN_BITNUMBER * 4)))
/* Alias word address of BDRST bit */
#define BDRST_BITNUMBER POSITION_VAL(RCC_BDCR_BDRST)
#define RCC_BDCR_BDRST_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (BDRST_BITNUMBER * 4)))
/* CR register byte 2 (Bits[23:16]) base address */
#define RCC_CR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CR_OFFSET + 0x02))
/* CIR register byte 1 (Bits[15:8]) base address */
#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x01))
/* CIR register byte 2 (Bits[23:16]) base address */
#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x02))
/* Defines used for Flags */
#define CR_REG_INDEX ((uint8_t)1)
#define BDCR_REG_INDEX ((uint8_t)2)
#define CSR_REG_INDEX ((uint8_t)3)
#define RCC_FLAG_MASK ((uint8_t)0x1F)
/**
* @}
*/
/** @addtogroup RCC_Private_Macros
* @{
*/
/** @defgroup RCC_Alias_For_Legacy Alias define maintained for legacy
* @{
*/
#define __HAL_RCC_SYSCFG_CLK_DISABLE __HAL_RCC_AFIO_CLK_DISABLE
#define __HAL_RCC_SYSCFG_CLK_ENABLE __HAL_RCC_AFIO_CLK_ENABLE
#define __HAL_RCC_SYSCFG_FORCE_RESET __HAL_RCC_AFIO_FORCE_RESET
#define __HAL_RCC_SYSCFG_RELEASE_RESET __HAL_RCC_AFIO_RELEASE_RESET
/**
* @}
*/
#define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON))
#define IS_RCC_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= 0x1F)
#define IS_RCC_CLOCKTYPE(__CLK__) ((1 <= (__CLK__)) && ((__CLK__) <= 15))
#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \
((__HSE__) == RCC_HSE_BYPASS))
#define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \
((__LSE__) == RCC_LSE_BYPASS))
#define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_HSI_DIV2) || \
((__SOURCE__) == RCC_PLLSOURCE_HSE))
#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \
(((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \
(((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \
(((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \
(((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE))
#define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON))
#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) || ((__PLL__) == RCC_PLL_OFF) || \
((__PLL__) == RCC_PLL_ON))
#define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \
((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \
((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK))
#define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \
((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \
((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \
((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \
((__HCLK__) == RCC_SYSCLK_DIV512))
#define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \
((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \
((__PCLK__) == RCC_HCLK_DIV16))
#define IS_RCC_MCO(__MCO__) (((__MCO__) == RCC_MCO))
#define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1))
/**
* @}
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup RCC_Exported_Types RCC Exported Types
* @{
*/
/**
* @brief RCC PLL configuration structure definition
*/
typedef struct
{
uint32_t PLLState; /*!< The new state of the PLL.
This parameter can be a value of @ref __HAL_RCC_PLL_CONFIG */
uint32_t PLLSource; /*!< PLLSource: PLL entry clock source.
This parameter must be a value of @ref RCC_PLL_Clock_Source */
uint32_t PLLMUL; /*!< PLLMUL: Multiplication factor for PLL VCO input clock
This parameter must be a value of @ref RCCEx_PLL_Multiplication_Factor */
} RCC_PLLInitTypeDef;
/**
* @brief RCC System, AHB and APB busses clock configuration structure definition
*/
typedef struct
{
uint32_t ClockType; /*!< The clock to be configured.
This parameter can be a value of @ref RCC_System_Clock_Type */
uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock.
This parameter can be a value of @ref RCC_System_Clock_Source */
uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK).
This parameter can be a value of @ref RCC_AHB_Clock_Source */
uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK).
This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */
uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK).
This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */
} RCC_ClkInitTypeDef;
/**
* @}
*/
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup RCC_Exported_Constants RCC Exported Constants
* @{
*/
/** @defgroup RCC_PLL_Clock_Source PLL Clock Source
* @{
*/
#define RCC_PLLSOURCE_HSI_DIV2 ((uint32_t)0x00000000) /*!< HSI clock divided by 2 selected as PLL entry clock source */
#define RCC_PLLSOURCE_HSE RCC_CFGR_PLLSRC /*!< HSE clock selected as PLL entry clock source */
/**
* @}
*/
/** @defgroup RCC_Oscillator_Type Oscillator Type
* @{
*/
#define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000)
#define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001)
#define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002)
#define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004)
#define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008)
/**
* @}
*/
/** @defgroup __HAL_RCC_HSE_CONFIG HSE Config
* @{
*/
#define RCC_HSE_OFF ((uint32_t)0x00000000) /*!< HSE clock deactivation */
#define RCC_HSE_ON ((uint32_t)0x00000001) /*!< HSE clock activation */
#define RCC_HSE_BYPASS ((uint32_t)0x00000005) /*!< External clock source for HSE clock */
/**
* @}
*/
/** @defgroup __HAL_RCC_LSE_CONFIG LSE Config
* @{
*/
#define RCC_LSE_OFF ((uint32_t)0x00000000) /*!< LSE clock deactivation */
#define RCC_LSE_ON ((uint32_t)0x00000001) /*!< LSE clock activation */
#define RCC_LSE_BYPASS ((uint32_t)0x00000005) /*!< External clock source for LSE clock */
/**
* @}
*/
/** @defgroup RCC_HSI_Config HSI Config
* @{
*/
#define RCC_HSI_OFF ((uint32_t)0x00000000) /*!< HSI clock deactivation */
#define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */
#define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x10) /* Default HSI calibration trimming value */
/**
* @}
*/
/** @defgroup RCC_LSI_Config LSI Config
* @{
*/
#define RCC_LSI_OFF ((uint32_t)0x00000000) /*!< LSI clock deactivation */
#define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */
/**
* @}
*/
/** @defgroup __HAL_RCC_PLL_CONFIG PLL Config
* @{
*/
#define RCC_PLL_NONE ((uint32_t)0x00000000) /*!< PLL is not configured */
#define RCC_PLL_OFF ((uint32_t)0x00000001) /*!< PLL deactivation */
#define RCC_PLL_ON ((uint32_t)0x00000002) /*!< PLL activation */
/**
* @}
*/
/** @defgroup RCC_System_Clock_Type System Clock Type
* @{
*/
#define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001) /*!< SYSCLK to configure */
#define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002) /*!< HCLK to configure */
#define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004) /*!< PCLK1 to configure */
#define RCC_CLOCKTYPE_PCLK2 ((uint32_t)0x00000008) /*!< PCLK2 to configure */
/**
* @}
*/
/** @defgroup RCC_System_Clock_Source System Clock Source
* @{
*/
#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selected as system clock */
#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selected as system clock */
#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selected as system clock */
/**
* @}
*/
/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status
* @{
*/
#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI
#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE
#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL
/**
* @}
*/
/** @defgroup RCC_AHB_Clock_Source AHB Clock Source
* @{
*/
#define RCC_SYSCLK_DIV1 (RCC_CFGR_HPRE_DIV1) /*!< SYSCLK not divided */
#define RCC_SYSCLK_DIV2 (RCC_CFGR_HPRE_DIV2) /*!< SYSCLK divided by 2 */
#define RCC_SYSCLK_DIV4 (RCC_CFGR_HPRE_DIV4) /*!< SYSCLK divided by 4 */
#define RCC_SYSCLK_DIV8 (RCC_CFGR_HPRE_DIV8) /*!< SYSCLK divided by 8 */
#define RCC_SYSCLK_DIV16 (RCC_CFGR_HPRE_DIV16) /*!< SYSCLK divided by 16 */
#define RCC_SYSCLK_DIV64 (RCC_CFGR_HPRE_DIV64) /*!< SYSCLK divided by 64 */
#define RCC_SYSCLK_DIV128 (RCC_CFGR_HPRE_DIV128) /*!< SYSCLK divided by 128 */
#define RCC_SYSCLK_DIV256 (RCC_CFGR_HPRE_DIV256) /*!< SYSCLK divided by 256 */
#define RCC_SYSCLK_DIV512 (RCC_CFGR_HPRE_DIV512) /*!< SYSCLK divided by 512 */
/**
* @}
*/
/** @defgroup RCC_APB1_APB2_Clock_Source APB1 APB2 Clock Source
* @{
*/
#define RCC_HCLK_DIV1 (RCC_CFGR_PPRE1_DIV1) /*!< HCLK not divided */
#define RCC_HCLK_DIV2 (RCC_CFGR_PPRE1_DIV2) /*!< HCLK divided by 2 */
#define RCC_HCLK_DIV4 (RCC_CFGR_PPRE1_DIV4) /*!< HCLK divided by 4 */
#define RCC_HCLK_DIV8 (RCC_CFGR_PPRE1_DIV8) /*!< HCLK divided by 8 */
#define RCC_HCLK_DIV16 (RCC_CFGR_PPRE1_DIV16) /*!< HCLK divided by 16 */
/**
* @}
*/
/** @defgroup RCC_RTC_Clock_Source RTC Clock Source
* @{
*/
#define RCC_RTCCLKSOURCE_LSE (RCC_BDCR_RTCSEL_LSE) /*!< LSE oscillator clock used as RTC clock */
#define RCC_RTCCLKSOURCE_LSI (RCC_BDCR_RTCSEL_LSI) /*!< LSI oscillator clock used as RTC clock */
#define RCC_RTCCLKSOURCE_HSE_DIV128 (RCC_BDCR_RTCSEL_HSE) /*!< HSE oscillator clock divided by 128 used as RTC clock */
/**
* @}
*/
/** @defgroup RCC_MCO_Index MCO Index
* @{
*/
#define RCC_MCO1 ((uint32_t)0x00000000)
#define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/
/**
* @}
*/
/** @defgroup RCC_MCOx_Clock_Prescaler MCO1 Clock Prescaler
* @{
*/
#define RCC_MCODIV_1 ((uint32_t)0x00000000)
/**
* @}
*/
/** @defgroup RCC_Interrupt Interrupts
* @{
*/
#define RCC_IT_LSIRDY ((uint8_t)RCC_CIR_LSIRDYF) /*!< LSI Ready Interrupt flag */
#define RCC_IT_LSERDY ((uint8_t)RCC_CIR_LSERDYF) /*!< LSE Ready Interrupt flag */
#define RCC_IT_HSIRDY ((uint8_t)RCC_CIR_HSIRDYF) /*!< HSI Ready Interrupt flag */
#define RCC_IT_HSERDY ((uint8_t)RCC_CIR_HSERDYF) /*!< HSE Ready Interrupt flag */
#define RCC_IT_PLLRDY ((uint8_t)RCC_CIR_PLLRDYF) /*!< PLL Ready Interrupt flag */
#define RCC_IT_CSS ((uint8_t)RCC_CIR_CSSF) /*!< Clock Security System Interrupt flag */
/**
* @}
*/
/** @defgroup RCC_Flag Flags
* Elements values convention: 0XXYYYYYb
* - YYYYY : Flag position in the register
* - XX : Register index
* - 01: CR register
* - 10: BDCR register
* - 11: CSR register
* @{
*/
/* Flags in the CR register */
#define RCC_FLAG_HSIRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSIRDY))) /*!< Internal High Speed clock ready flag */
#define RCC_FLAG_HSERDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSERDY))) /*!< External High Speed clock ready flag */
#define RCC_FLAG_PLLRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_PLLRDY))) /*!< PLL clock ready flag */
/* Flags in the BDCR register */
#define RCC_FLAG_LSERDY ((uint8_t)((BDCR_REG_INDEX << 5) | POSITION_VAL(RCC_BDCR_LSERDY))) /*!< External Low Speed oscillator Ready */
/* Flags in the CSR register */
#define RCC_FLAG_LSIRDY ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LSIRDY))) /*!< Internal Low Speed oscillator Ready */
#define RCC_FLAG_RMV ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_RMVF))) /*!< Remove reset flag */
#define RCC_FLAG_PINRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_PINRSTF))) /*!< PIN reset flag */
#define RCC_FLAG_PORRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_PORRSTF))) /*!< POR/PDR reset flag */
#define RCC_FLAG_SFTRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_SFTRSTF))) /*!< Software Reset flag */
#define RCC_FLAG_IWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_IWDGRSTF))) /*!< Independent Watchdog reset flag */
#define RCC_FLAG_WWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_WWDGRSTF))) /*!< Window watchdog reset flag */
#define RCC_FLAG_LPWRRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LPWRRSTF))) /*!< Low-Power reset flag */
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup RCC_Exported_Macros RCC Exported Macros
* @{
*/
/** @defgroup RCC_Peripheral_Clock_Enable_Disable Peripheral Clock Enable Disable
* @brief Enable or disable the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_DMA1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_SRAM_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_FLITF_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_CRC_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_DMA1EN))
#define __HAL_RCC_SRAM_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_SRAMEN))
#define __HAL_RCC_FLITF_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_FLITFEN))
#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_CRCEN))
/**
* @}
*/
/** @defgroup RCC_AHB_Peripheral_Clock_Enable_Disable_Status AHB Peripheral Clock Enable Disable Status
* @brief Get the enable or disable status of the AHB peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) != RESET)
#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) == RESET)
#define __HAL_RCC_SRAM_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) != RESET)
#define __HAL_RCC_SRAM_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) == RESET)
#define __HAL_RCC_FLITF_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) != RESET)
#define __HAL_RCC_FLITF_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) == RESET)
#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) != RESET)
#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) == RESET)
/**
* @}
*/
/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Clock Enable Disable
* @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_WWDG_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_USART2_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_I2C1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_BKP_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_PWR_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN))
#define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN))
#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN))
#define __HAL_RCC_BKP_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_BKPEN))
#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN))
/**
* @}
*/
/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status
* @brief Get the enable or disable status of the APB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET)
#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET)
#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET)
#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET)
#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET)
#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET)
#define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET)
#define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET)
#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET)
#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET)
#define __HAL_RCC_BKP_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) != RESET)
#define __HAL_RCC_BKP_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) == RESET)
#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET)
#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET)
/**
* @}
*/
/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Clock Enable Disable
* @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_AFIO_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_ADC1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_TIM1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_SPI1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_USART1_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_AFIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_AFIOEN))
#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPAEN))
#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPBEN))
#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPCEN))
#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPDEN))
#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN))
#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN))
#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN))
#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN))
/**
* @}
*/
/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status
* @brief Get the enable or disable status of the APB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
* @{
*/
#define __HAL_RCC_AFIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) != RESET)
#define __HAL_RCC_AFIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) == RESET)
#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) != RESET)
#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) == RESET)
#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) != RESET)
#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) == RESET)
#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) != RESET)
#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) == RESET)
#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) != RESET)
#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) == RESET)
#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET)
#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET)
#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET)
#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET)
#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET)
#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET)
#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET)
#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET)
/**
* @}
*/
/** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset
* @brief Force or release APB1 peripheral reset.
* @{
*/
#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFF)
#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST))
#define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST))
#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST))
#define __HAL_RCC_BKP_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_BKPRST))
#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST))
#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00)
#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST))
#define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST))
#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST))
#define __HAL_RCC_BKP_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_BKPRST))
#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST))
/**
* @}
*/
/** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset
* @brief Force or release APB2 peripheral reset.
* @{
*/
#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFF)
#define __HAL_RCC_AFIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_AFIORST))
#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPARST))
#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPBRST))
#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPCRST))
#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPDRST))
#define __HAL_RCC_ADC1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC1RST))
#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST))
#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST))
#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST))
#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00)
#define __HAL_RCC_AFIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_AFIORST))
#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPARST))
#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPBRST))
#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPCRST))
#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPDRST))
#define __HAL_RCC_ADC1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC1RST))
#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST))
#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST))
#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST))
/**
* @}
*/
/** @defgroup RCC_HSI_Configuration HSI Configuration
* @{
*/
/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI).
* @note The HSI is stopped by hardware when entering STOP and STANDBY modes.
* @note HSI can not be stopped if it is used as system clock source. In this case,
* you have to select another source of the system clock then stop the HSI.
* @note After enabling the HSI, the application software should wait on HSIRDY
* flag to be set indicating that HSI clock is stable and can be used as
* system clock source.
* @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator
* clock cycles.
*/
#define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE)
#define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE)
/** @brief macro to adjust the Internal High Speed oscillator (HSI) calibration value.
* @note The calibration is used to compensate for the variations in voltage
* and temperature that influence the frequency of the internal HSI RC.
* @param _HSICALIBRATIONVALUE_: specifies the calibration trimming value.
* (default is RCC_HSICALIBRATION_DEFAULT).
* This parameter must be a number between 0 and 0x1F.
*/
#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(_HSICALIBRATIONVALUE_) \
(MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, (uint32_t)(_HSICALIBRATIONVALUE_) << POSITION_VAL(RCC_CR_HSITRIM)))
/**
* @}
*/
/** @defgroup RCC_LSI_Configuration LSI Configuration
* @{
*/
/** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI).
* @note After enabling the LSI, the application software should wait on
* LSIRDY flag to be set indicating that LSI clock is stable and can
* be used to clock the IWDG and/or the RTC.
* @note LSI can not be disabled if the IWDG is running.
* @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator
* clock cycles.
*/
#define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE)
#define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE)
/**
* @}
*/
/** @defgroup RCC_HSE_Configuration HSE Configuration
* @{
*/
/**
* @brief Macro to configure the External High Speed oscillator (HSE).
* @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application
* software should wait on HSERDY flag to be set indicating that HSE clock
* is stable and can be used to clock the PLL and/or system clock.
* @note HSE state can not be changed if it is used directly or through the
* PLL as system clock. In this case, you have to select another source
* of the system clock then change the HSE state (ex. disable it).
* @note The HSE is stopped by hardware when entering STOP and STANDBY modes.
* @note This function reset the CSSON bit, so if the Clock security system(CSS)
* was previously enabled you have to enable it again after calling this
* function.
* @param __STATE__: specifies the new state of the HSE.
* This parameter can be one of the following values:
* @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after
* 6 HSE oscillator clock cycles.
* @arg RCC_HSE_ON: turn ON the HSE oscillator
* @arg RCC_HSE_BYPASS: HSE oscillator bypassed with external clock
*/
#define __HAL_RCC_HSE_CONFIG(__STATE__) \
do { \
CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \
if((__STATE__) == RCC_HSE_ON) \
{ \
CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \
SET_BIT(RCC->CR, RCC_CR_HSEON); \
} \
else if((__STATE__) == RCC_HSE_BYPASS) \
{ \
(*(__IO uint8_t *) RCC_CR_BYTE2_ADDRESS = (__STATE__)); \
} \
else \
{ \
CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \
} \
} while(0)
/**
* @}
*/
/** @defgroup RCC_LSE_Configuration LSE Configuration
* @{
*/
/** @brief Macros to enable or disable the Internal Low Speed oscillator (LSE).
*/
#define __HAL_RCC_LSE_CONFIG(__LSE_STATE__) \
do{ \
if ((__LSE_STATE__) == RCC_LSE_OFF) \
{ \
*(__IO uint32_t *) BDCR_LSEON_BB = DISABLE; \
*(__IO uint32_t *) BDCR_LSEBYP_BB = DISABLE; \
} \
else if ((__LSE_STATE__) == RCC_LSE_ON) \
{ \
*(__IO uint32_t *) BDCR_LSEBYP_BB = DISABLE; \
*(__IO uint32_t *) BDCR_LSEON_BB = ENABLE; \
} \
else \
{ \
*(__IO uint32_t *) BDCR_LSEON_BB = DISABLE; \
*(__IO uint32_t *) BDCR_LSEBYP_BB = ENABLE; \
} \
}while(0)
/**
* @}
*/
/** @defgroup RCC_PLL_Configuration PLL Configuration
* @{
*/
/** @brief Macros to enable the main PLL.
* @note After enabling the main PLL, the application software should wait on
* PLLRDY flag to be set indicating that PLL clock is stable and can
* be used as system clock source.
* @note The main PLL is disabled by hardware when entering STOP and STANDBY modes.
*/
#define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE)
/** @brief Macros to disable the main PLL.
* @note The main PLL can not be disabled if it is used as system clock source
*/
#define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE)
/** @brief macros to configure the main PLL clock source and multiplication factors.
* @note This function must be used only when the main PLL is disabled.
*
* @param __RCC_PLLSOURCE__: specifies the PLL entry clock source.
* This parameter can be one of the following values:
* @arg RCC_PLLSOURCE_HSI_DIV2: HSI oscillator clock selected as PLL clock entry
* @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry
* @param __PLLMUL__: specifies the multiplication factor for PLL VCO output clock
* This parameter can be one of the following values:
* @arg RCC_PLL_MUL2: PLLVCO = PLL clock entry x 2 (*)
* @arg RCC_PLL_MUL3: PLLVCO = PLL clock entry x 3 (*)
* @arg RCC_PLL_MUL4: PLLVCO = PLL clock entry x 4
* @arg RCC_PLL_MUL6: PLLVCO = PLL clock entry x 6
* @arg RCC_PLL_MUL6_5: PLLVCO = PLL clock entry x 6.5 (**)
* @arg RCC_PLL_MUL8: PLLVCO = PLL clock entry x 8
* @arg RCC_PLL_MUL9: PLLVCO = PLL clock entry x 9
* @arg RCC_PLL_MUL10: PLLVCO = PLL clock entry x 10 (*)
* @arg RCC_PLL_MUL11: PLLVCO = PLL clock entry x 11 (*)
* @arg RCC_PLL_MUL12: PLLVCO = PLL clock entry x 12 (*)
* @arg RCC_PLL_MUL13: PLLVCO = PLL clock entry x 13 (*)
* @arg RCC_PLL_MUL14: PLLVCO = PLL clock entry x 14 (*)
* @arg RCC_PLL_MUL15: PLLVCO = PLL clock entry x 15 (*)
* @arg RCC_PLL_MUL16: PLLVCO = PLL clock entry x 16 (*)
* @note (*) These values are not available in STM32F105xx & STM32F107xx devices.
* @note (**) This value is available in STM32F105xx & STM32F107xx devices only.
*
*/
#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSOURCE__, __PLLMUL__)\
MODIFY_REG(RCC->CFGR, (RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL),((__RCC_PLLSOURCE__) | (__PLLMUL__) ))
/**
* @}
*/
/** @defgroup RCC_Get_Clock_source Get Clock source
* @{
*/
/** @brief Macro to get the clock source used as system clock.
* @retval The clock source used as system clock. The returned value can be one
* of the following:
* @arg RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock
* @arg RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock
* @arg RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock
*/
#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR,RCC_CFGR_SWS)))
/** @brief Get oscillator clock selected as PLL input clock
* @retval The clock source used for PLL entry. The returned value can be one
* of the following:
* @arg RCC_PLLSOURCE_HSI_DIV2: HSI oscillator clock selected as PLL input clock
* @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL input clock
*/
#define __HAL_RCC_GET_PLL_OSCSOURCE() ((RCC->CFGR & RCC_CFGR_PLLSRC))
/**
* @}
*/
/** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration
* @{
*/
/** @brief Macro to configures the RTC clock (RTCCLK).
* @note As the RTC clock configuration bits are in the Backup domain and write
* access is denied to this domain after reset, you have to enable write
* access using the Power Backup Access macro before to configure
* the RTC clock source (to be done once after reset).
* @note Once the RTC clock is configured it can't be changed unless the
* Backup domain is reset using __HAL_RCC_BACKUPRESET_FORCE() macro, or by
* a Power On Reset (POR).
*
* @param __RTC_CLKSOURCE__: specifies the RTC clock source.
* This parameter can be one of the following values:
* @arg RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock
* @arg RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock
* @arg RCC_RTCCLKSOURCE_HSE_DIV128: HSE divided by 128 selected as RTC clock
* @note If the LSE or LSI is used as RTC clock source, the RTC continues to
* work in STOP and STANDBY modes, and can be used as wakeup source.
* However, when the HSE clock is used as RTC clock source, the RTC
* cannot be used in STOP and STANDBY modes.
* @note The maximum input clock frequency for RTC is 1MHz (when using HSE as
* RTC clock source).
*/
#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) MODIFY_REG(RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__))
/** @brief macros to get the RTC clock source.
*/
#define __HAL_RCC_GET_RTC_SOURCE() READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)
/** @brief Macros to enable the the RTC clock.
* @note These macros must be used only after the RTC clock source was selected.
*/
#define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE)
/** @brief Macros to disable the the RTC clock.
* @note These macros must be used only after the RTC clock source was selected.
*/
#define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE)
/** @brief Macros to force the Backup domain reset.
* @note This function resets the entire Backup domain.
*/
#define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE)
/** @brief Macros to release the Backup domain reset.
*/
#define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE)
/**
* @}
*/
/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management
* @brief macros to manage the specified RCC Flags and interrupts.
* @{
*/
/** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable
* the selected interrupts.).
* @param __INTERRUPT__: specifies the RCC interrupt sources to be enabled.
* This parameter can be any combination of the following values:
* @arg RCC_IT_LSIRDY: LSI ready interrupt
* @arg RCC_IT_LSERDY: LSE ready interrupt
* @arg RCC_IT_HSIRDY: HSI ready interrupt
* @arg RCC_IT_HSERDY: HSE ready interrupt
* @arg RCC_IT_PLLRDY: main PLL ready interrupt
* @arg RCC_IT_PLL2RDY: Main PLL2 ready interrupt.(*)
* @arg RCC_IT_PLLI2S2RDY: Main PLLI2S ready interrupt.(*)
* @note (*) This bit is available in STM32F105xx & STM32F107xx devices only.
*/
#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__))
/** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable
* the selected interrupts).
* @param __INTERRUPT__: specifies the RCC interrupt sources to be disabled.
* This parameter can be any combination of the following values:
* @arg RCC_IT_LSIRDY: LSI ready interrupt
* @arg RCC_IT_LSERDY: LSE ready interrupt
* @arg RCC_IT_HSIRDY: HSI ready interrupt
* @arg RCC_IT_HSERDY: HSE ready interrupt
* @arg RCC_IT_PLLRDY: main PLL ready interrupt
* @arg RCC_IT_PLL2RDY: Main PLL2 ready interrupt.(*)
* @arg RCC_IT_PLLI2S2RDY: Main PLLI2S ready interrupt.(*)
* @note (*) This bit is available in STM32F105xx & STM32F107xx devices only.
*/
#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= ~(__INTERRUPT__))
/** @brief Clear the RCC's interrupt pending bits ( Perform Byte access to RCC_CIR[23:16]
* bits to clear the selected interrupt pending bits.
* @param __INTERRUPT__: specifies the interrupt pending bit to clear.
* This parameter can be any combination of the following values:
* @arg RCC_IT_LSIRDY: LSI ready interrupt.
* @arg RCC_IT_LSERDY: LSE ready interrupt.
* @arg RCC_IT_HSIRDY: HSI ready interrupt.
* @arg RCC_IT_HSERDY: HSE ready interrupt.
* @arg RCC_IT_PLLRDY: Main PLL ready interrupt.
* @arg RCC_IT_PLL2RDY: Main PLL2 ready interrupt.(*)
* @arg RCC_IT_PLLI2S2RDY: Main PLLI2S ready interrupt.(*)
* @note (*) This bit is available in STM32F105xx & STM32F107xx devices only.
* @arg RCC_IT_CSS: Clock Security System interrupt
*/
#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__))
/** @brief Check the RCC's interrupt has occurred or not.
* @param __INTERRUPT__: specifies the RCC interrupt source to check.
* This parameter can be one of the following values:
* @arg RCC_IT_LSIRDY: LSI ready interrupt.
* @arg RCC_IT_LSERDY: LSE ready interrupt.
* @arg RCC_IT_HSIRDY: HSI ready interrupt.
* @arg RCC_IT_HSERDY: HSE ready interrupt.
* @arg RCC_IT_PLLRDY: Main PLL ready interrupt.
* @arg RCC_IT_PLL2RDY: Main PLL2 ready interrupt.(*)
* @arg RCC_IT_PLLI2S2RDY: Main PLLI2S ready interrupt.(*)
* @arg RCC_IT_CSS: Clock Security System interrupt
* @note (*) This bit is available in STM32F105xx & STM32F107xx devices only.
* @retval The new state of __INTERRUPT__ (TRUE or FALSE).
*/
#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__))
/** @brief Set RMVF bit to clear the reset flags: RCC_FLAG_PINRST, RCC_FLAG_PORRST, RCC_FLAG_SFTRST,
* RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST, RCC_FLAG_LPWRRST
*/
#define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF)
/** @brief Check RCC flag is set or not.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready.
* @arg RCC_FLAG_HSERDY: HSE oscillator clock ready.
* @arg RCC_FLAG_PLLRDY: Main PLL clock ready.
* @arg RCC_FLAG_PLL2RDY: Main PLL2 clock ready.(*)
* @arg RCC_FLAG_PLLI2SRDY: Main PLLI2S clock ready.(*)
* @arg RCC_FLAG_LSERDY: LSE oscillator clock ready.
* @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready.
* @arg RCC_FLAG_PINRST: Pin reset.
* @arg RCC_FLAG_PORRST: POR/PDR reset.
* @arg RCC_FLAG_SFTRST: Software reset.
* @arg RCC_FLAG_IWDGRST: Independent Watchdog reset.
* @arg RCC_FLAG_WWDGRST: Window Watchdog reset.
* @arg RCC_FLAG_LPWRRST: Low Power reset.
* @note (*) This bit is available in STM32F105xx & STM32F107xx devices only.
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_RCC_GET_FLAG(__FLAG__) (((((__FLAG__) >> 5) == CR_REG_INDEX)? RCC->CR :((((__FLAG__) >> 5) == BDCR_REG_INDEX)? RCC->BDCR : RCC->CSR)) & ((uint32_t)1 << ((__FLAG__) & RCC_FLAG_MASK)))
/**
* @}
*/
/**
* @}
*/
/* Include RCC HAL Extension module */
#include "stm32f1xx_hal_rcc_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup RCC_Exported_Functions
* @{
*/
/** @addtogroup RCC_Exported_Functions_Group1
* @{
*/
/* Initialization and de-initialization functions ******************************/
void HAL_RCC_DeInit(void);
HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency);
/**
* @}
*/
/** @addtogroup RCC_Exported_Functions_Group2
* @{
*/
/* Peripheral Control functions ************************************************/
void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv);
void HAL_RCC_EnableCSS(void);
void HAL_RCC_DisableCSS(void);
uint32_t HAL_RCC_GetSysClockFreq(void);
uint32_t HAL_RCC_GetHCLKFreq(void);
uint32_t HAL_RCC_GetPCLK1Freq(void);
uint32_t HAL_RCC_GetPCLK2Freq(void);
void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency);
/* CSS NMI IRQ handler */
void HAL_RCC_NMI_IRQHandler(void);
/* User Callbacks in non blocking mode (IT mode) */
void HAL_RCC_CSSCallback(void);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F1xx_HAL_RCC_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/