Diff: examples/IRremoteInfo/IRremoteInfo.ino

Revision:

2:6bbd1e911324

Parent:

1:370967a90abb

Child:

3:17440cf7ab90

diff -r 370967a90abb -r 6bbd1e911324 examples/IRremoteInfo/IRremoteInfo.ino
--- a/examples/IRremoteInfo/IRremoteInfo.ino	Sat Jan 23 15:25:05 2016 +0900
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,210 +0,0 @@
-/*
- * IRremote: IRremoteInfo - prints relevant config info & settings for IRremote over serial
- * Intended to help identify & troubleshoot the various settings of IRremote
- * For example, sometimes users are unsure of which pin is used for Tx or the RAWBUF values
- * This example can be used to assist the user directly or with support.
- * Intended to help identify & troubleshoot the various settings of IRremote
- * Hopefully this utility will be a useful tool for support & troubleshooting for IRremote
- * Check out the blog post describing the sketch via http://www.analysir.com/blog/2015/11/28/helper-utility-for-troubleshooting-irremote/
- * Version 1.0 November 2015
- * Original Author: AnalysIR - IR software & modules for Makers & Pros, visit http://www.AnalysIR.com
- */
-
-
-#include <IRremote.h>
-
-void setup()
-{
-  Serial.begin(115200); //You may alter the BAUD rate here as needed
-  while (!Serial); //wait until Serial is established - required on some Platforms
-
-  //Runs only once per restart of the Arduino.
-  dumpHeader();
-  dumpRAWBUF();
-  dumpTIMER();
-  dumpTimerPin();
-  dumpClock();
-  dumpPlatform();
-  dumpPulseParams();
-  dumpSignalParams();
-  dumpArduinoIDE();
-  dumpDebugMode();
-  dumpProtocols();
-  dumpFooter();
-}
-
-void loop() {
-  //nothing to do!
-}
-
-void dumpRAWBUF() {
-  Serial.print(F("RAWBUF: "));
-  Serial.println(RAWBUF);
-}
-
-void dumpTIMER() {
-  boolean flag = false;
-#ifdef IR_USE_TIMER1
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer1")); flag = true;
-#endif
-#ifdef IR_USE_TIMER2
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer2")); flag = true;
-#endif
-#ifdef IR_USE_TIMER3
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer3")); flag = true;
-#endif
-#ifdef IR_USE_TIMER4
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer4")); flag = true;
-#endif
-#ifdef IR_USE_TIMER5
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer5")); flag = true;
-#endif
-#ifdef IR_USE_TIMER4_HS
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer4_HS")); flag = true;
-#endif
-#ifdef IR_USE_TIMER_CMT
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer_CMT")); flag = true;
-#endif
-#ifdef IR_USE_TIMER_TPM1
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer_TPM1")); flag = true;
-#endif
-#ifdef IR_USE_TIMER_TINY0
-  Serial.print(F("Timer defined for use: ")); Serial.println(F("Timer_TINY0")); flag = true;
-#endif
-
-  if (!flag) {
-    Serial.print(F("Timer Error: ")); Serial.println(F("not defined"));
-  }
-}
-
-void dumpTimerPin() {
-  Serial.print(F("IR Tx Pin: "));
-  Serial.println(TIMER_PWM_PIN);
-}
-
-void dumpClock() {
-  Serial.print(F("MCU Clock: "));
-  Serial.println(F_CPU);
-}
-
-void dumpPlatform() {
-  Serial.print(F("MCU Platform: "));
-
-#if defined(__AVR_ATmega1280__)
-  Serial.println(F("Arduino Mega1280"));
-#elif  defined(__AVR_ATmega2560__)
-  Serial.println(F("Arduino Mega2560"));
-#elif defined(__AVR_AT90USB162__)
-  Serial.println(F("Teensy 1.0 / AT90USB162"));
-  // Teensy 2.0
-#elif defined(__AVR_ATmega32U4__)
-  Serial.println(F("Arduino Leonardo / Yun / Teensy 1.0 / ATmega32U4"));
-#elif defined(__MK20DX128__) || defined(__MK20DX256__)
-  Serial.println(F("Teensy 3.0 / Teensy 3.1 / MK20DX128 / MK20DX256"));
-#elif defined(__MKL26Z64__)
-  Serial.println(F("Teensy-LC / MKL26Z64"));
-#elif defined(__AVR_AT90USB646__)
-  Serial.println(F("Teensy++ 1.0 / AT90USB646"));
-#elif defined(__AVR_AT90USB1286__)
-  Serial.println(F("Teensy++ 2.0 / AT90USB1286"));
-#elif defined(__AVR_ATmega644P__) || defined(__AVR_ATmega644__)
-  Serial.println(F("Sanguino / ATmega644(P)"));
-#elif defined(__AVR_ATmega8P__) || defined(__AVR_ATmega8__)
-  Serial.println(F("Atmega8 / ATmega8(P)"));
-#elif defined(__AVR_ATtiny84__)
-  Serial.println(F("ATtiny84"));
-#elif defined(__AVR_ATtiny85__)
-  Serial.println(F("ATtiny85"));
-#else
-  Serial.println(F("ATmega328(P) / (Duemilanove, Diecimila, LilyPad, Mini, Micro, Fio, Nano, etc)"));
-#endif
-}
-
-void dumpPulseParams() {
-  Serial.print(F("Mark Excess: ")); Serial.print(MARK_EXCESS);; Serial.println(F(" uSecs"));
-  Serial.print(F("Microseconds per tick: ")); Serial.print(USECPERTICK);; Serial.println(F(" uSecs"));
-  Serial.print(F("Measurement tolerance: ")); Serial.print(TOLERANCE); Serial.println(F("%"));
-}
-
-void dumpSignalParams() {
-  Serial.print(F("Minimum Gap between IR Signals: ")); Serial.print(_GAP); Serial.println(F(" uSecs"));
-}
-
-void dumpDebugMode() {
-  Serial.print(F("Debug Mode: "));
-#if DEBUG
-  Serial.println(F("ON"));
-#else
-  Serial.println(F("OFF (Normal)"));
-#endif
-
-}
-
-void dumpArduinoIDE() {
-  Serial.print(F("Arduino IDE version: "));
-  Serial.print(ARDUINO / 10000);
-  Serial.write('.');
-  Serial.print((ARDUINO % 10000) / 100);
-  Serial.write('.');
-  Serial.println(ARDUINO % 100);
-}
-
-void dumpProtocols() {
-
-  Serial.println(); Serial.print(F("IR PROTOCOLS  "));  Serial.print(F("SEND     "));  Serial.println(F("DECODE"));
-  Serial.print(F("============= "));  Serial.print(F("======== "));  Serial.println(F("========"));
-  Serial.print(F("RC5:          "));  printSendEnabled(SEND_RC5);  printDecodeEnabled(DECODE_RC6);
-  Serial.print(F("RC6:          "));  printSendEnabled(SEND_RC6);  printDecodeEnabled(DECODE_RC5);
-  Serial.print(F("NEC:          "));  printSendEnabled(SEND_NEC);  printDecodeEnabled(DECODE_NEC);
-  Serial.print(F("SONY:         "));  printSendEnabled(SEND_SONY);  printDecodeEnabled(DECODE_SONY);
-  Serial.print(F("PANASONIC:    "));  printSendEnabled(SEND_PANASONIC);  printDecodeEnabled(DECODE_PANASONIC);
-  Serial.print(F("JVC:          "));  printSendEnabled(SEND_JVC);  printDecodeEnabled(DECODE_JVC);
-  Serial.print(F("SAMSUNG:      "));  printSendEnabled(SEND_SAMSUNG);  printDecodeEnabled(DECODE_SAMSUNG);
-  Serial.print(F("WHYNTER:      "));  printSendEnabled(SEND_WHYNTER);  printDecodeEnabled(DECODE_WHYNTER);
-  Serial.print(F("AIWA_RC_T501: "));  printSendEnabled(SEND_AIWA_RC_T501);  printDecodeEnabled(DECODE_AIWA_RC_T501);
-  Serial.print(F("LG:           "));  printSendEnabled(SEND_LG);  printDecodeEnabled(DECODE_LG);
-  Serial.print(F("SANYO:        "));  printSendEnabled(SEND_SANYO);  printDecodeEnabled(DECODE_SANYO);
-  Serial.print(F("MITSUBISHI:   "));  printSendEnabled(SEND_MITSUBISHI);  printDecodeEnabled(DECODE_MITSUBISHI);
-  Serial.print(F("DISH:         "));  printSendEnabled(SEND_DISH);  printDecodeEnabled(DECODE_DISH);
-  Serial.print(F("SHARP:        "));  printSendEnabled(SEND_SHARP);  printDecodeEnabled(DECODE_SHARP);
-  Serial.print(F("DENON:        "));  printSendEnabled(SEND_DENON);  printDecodeEnabled(DECODE_DENON);
-  Serial.print(F("PRONTO:       "));  printSendEnabled(SEND_PRONTO);  Serial.println(F("(Not Applicable)"));
-}
-
-void printSendEnabled(int flag) {
-  if (flag) {
-    Serial.print(F("Enabled  "));
-  }
-  else {
-    Serial.print(F("Disabled "));
-  }
-}
-
-void printDecodeEnabled(int flag) {
-  if (flag) {
-    Serial.println(F("Enabled"));
-  }
-  else {
-    Serial.println(F("Disabled"));
-  }
-}
-
-void dumpHeader() {
-  Serial.println(F("IRremoteInfo - by AnalysIR (http://www.AnalysIR.com/)"));
-  Serial.println(F("             - A helper sketch to assist in troubleshooting issues with the library by reviewing the settings within the IRremote library"));
-  Serial.println(F("             - Prints out the important settings within the library, which can be configured to suit the many supported platforms"));
-  Serial.println(F("             - When seeking on-line support, please post or upload the output of this sketch, where appropriate"));
-  Serial.println();
-  Serial.println(F("IRremote Library Settings"));
-  Serial.println(F("========================="));
-}
-
-void dumpFooter() {
-  Serial.println();
-  Serial.println(F("Notes: "));
-  Serial.println(F("     - Most of the seetings above can be configured in the following files included as part of the library"));
-  Serial.println(F("     - IRremteInt.h"));
-  Serial.println(F("     - IRremote.h"));
-  Serial.println(F("     - You can save SRAM by disabling the Decode or Send features for any protocol (Near the top of IRremoteInt.h)"));
-  Serial.println(F("     - Some Timer conflicts, with other libraries, can be easily resolved by configuring a differnt Timer for your platform"));
-}