Revision 0:20d8ef79d787, committed 2014-12-24

Comitter:

wim

Date:

Wed Dec 24 01:09:26 2014 +0000

Commit message:

Test for v04 of lib. Set I2C clock at 100kb/s for reliable operation.

Changed in this revision

diff -r 000000000000 -r 20d8ef79d787 SC16IS750.lib
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/SC16IS750.lib	Wed Dec 24 01:09:26 2014 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/wim/code/SC16IS750/#ff3e57bebb6a

diff -r 000000000000 -r 20d8ef79d787 main.cpp
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Wed Dec 24 01:09:26 2014 +0000
@@ -0,0 +1,320 @@
+#include "mbed.h"
+#include "SC16IS750.h"
+ 
+ 
+#if defined(TARGET_LPC1768)
+// SPI for LPC1768
+#define D_MOSI                 p5
+#define D_MISO                 p6
+#define D_SCLK                 p7
+#define D_CS                   p8
+#define D_INTR                 p15
+#define D_RST                  p16
+
+// I2C for KL25Z
+#define D_SCL                  p10
+#define D_SDA                  p9
+ 
+// Serial for LPC1768
+#define D_TX                   USBTX
+#define D_RX                   USBRX
+//#define D_RST                  p25
+//#define D_STS                  p26
+
+DigitalOut myled1(LED1);
+//DigitalOut myled2(LED2); 
+//DigitalOut myled3(LED3);
+DigitalOut heartbeatLED(LED4);
+#endif
+ 
+#if defined(TARGET_KL25Z)
+// SPI for KL25Z
+#define D_MOSI                 PTD2
+#define D_MISO                 PTD3
+#define D_SCLK                 PTD1
+#define D_CS                   PTD0
+//#define D_INTR                 PTA13
+#define D_RST                  PTD5
+ 
+// I2C for KL25Z
+#define D_SCL                  PTE1
+#define D_SDA                  PTE0
+ 
+// Serial for KL25Z
+#define D_TX                   USBTX
+#define D_RX                   USBRX
+
+DigitalOut myled1(LED_RED);
+//DigitalOut myled2(LED_GREEN); 
+//DigitalOut myled3(LED_BLUE);  // Same as PTD1 (SCK)
+DigitalOut heartbeatLED(LED_GREEN);
+#endif
+ 
+#if defined(TARGET_LPC812)
+// SPI for LPC812
+#define D_MOSI                 P0_14
+#define D_MISO                 P0_15
+#define D_SCLK                 P0_12
+#define D_CS                   P0_13
+//#define D_INTR                 P0_7
+//#define D_RST                  P0_8
+ 
+// Serial for LPC812
+#define D_TX                   P0_4
+#define D_RX                   P0_0
+//#define D_RST                  P0_9
+//#define D_STS                  P0_17
+#endif
+ 
+ 
+//SPI Version
+SPI spi(D_MOSI, D_MISO, D_SCLK); //MOSI, MISO, SCK
+//SC16IS750_SPI serial_bridge(&spi, D_CS);
+//SC16IS750_SPI serial_bridge(&spi, D_CS, D_RST);  // version with Hardware Reset pin
+//SC16IS752_SPI serial_bridge(&spi, D_CS, D_RST, SC16IS750::Channel_A);  // Dual UART version with Hardware Reset pin
+//SC16IS752_SPI serial_bridge(&spi, D_CS, D_RST, SC16IS750::Channel_B);  // Dual UART version with Hardware Reset pin
+ 
+//I2C Version
+I2C i2c(D_SDA, D_SCL);       //SDA, SCL
+//SC16IS750_I2C serial_bridge(&i2c, SC16IS750_DEFAULT_ADDR);
+//SC16IS750_I2C serial_bridge(&i2c, SC16IS750_DEFAULT_ADDR, D_RST);
+SC16IS752_I2C serial_bridge(&i2c, SC16IS750_DEFAULT_ADDR, D_RST, SC16IS750::Channel_A);  // Dual UART version with Hardware Reset pin
+//SC16IS752_I2C serial_bridge(&i2c, SC16IS750_DEFAULT_ADDR, D_RST, SC16IS750::Channel_B);  // Dual UART version with Hardware Reset pin
+ 
+ 
+Serial pc(D_TX,D_RX);
+ 
+void show_menu() {
+    pc.printf("0: Exit\n\r");
+    pc.printf("1: Show Menu\n\r");    
+    pc.printf("2: Init\n\r"); 
+    pc.printf("3: IO Port Out\n\r");     
+    pc.printf("4: Transparant mode\n\r");        
+    pc.printf("5: Free bufferspace\n\r");                
+    pc.printf("6: Enable RTS/CTS\n\r");                
+    pc.printf("7: Disable RTS/CTS\n\r");                    
+    pc.printf("8: Write block\n\r");       
+    pc.printf("9: Baudrate 9600\n\r");                            
+    pc.printf("A: Baudrate 115200\n\r");                           
+    pc.printf("B: Transparant mode with bufferdisplay\n\r");        
+    pc.printf("C: Test printf \n\r");   
+    pc.printf("D: Test connected\n\r");                                
+ 
+ #if(0)                
+    pc.printf("D: \n\r");                           
+    pc.printf("P: \n\r");                        
+#endif    
+    pc.printf("\n\r");                
+}
+ 
+// Variables for Heartbeat and Status monitoring
+Ticker heartbeat;
+bool heartbeatflag=false;
+ 
+// Local functions
+void clear_screen() {
+//ANSI Terminal Commands
+    pc.printf("\x1B[2J");
+    pc.printf("\x1B[H");
+}
+ 
+   
+// Heartbeat monitor
+void pulse() {
+  heartbeatLED = !heartbeatLED;
+}
+ 
+void heartbeat_start() {
+  heartbeat.attach(&pulse, 0.5);
+}
+ 
+void heartbeat_stop() {
+  heartbeat.detach();
+}
+ 
+ 
+int main() {
+  bool running=true;
+  bool running_test=true;                   
+  char command, ch;
+  int i=0;
+   
+#if defined(TARGET_LPC1768)
+  pc.printf("\r\nHello World from LPC1768\r\n");
+#endif  
+#if defined(TARGET_KL25Z)
+  pc.printf("\r\nHello World from KL25Z\r\n");
+#endif  
+#if defined(TARGET_LPC812)
+  pc.printf("\r\nHello World from LPC812\r\n");
+#endif
+ 
+ 
+  heartbeat_start();     
+ 
+  myled1 = 1; // LED Off
+ 
+ // We need to enable flow control or we overflow buffers and
+  // lose data when used with the WiFly. Note that flow control 
+  // needs to be enabled on the WiFly for this to work but it's
+  // possible to do that with flow control enabled here but not there.
+//  serial_bridge.set_flow_control(SC16IS750::RTSCTS);
+ 
+    serial_bridge.ioSetDirection(0xFF); // All outputs
+    serial_bridge.ioSetState(0xFF);     // All On
+ 
+    show_menu();
+      
+    while(running) {
+     
+       if(pc.readable()) {
+         command = pc.getc();       
+         pc.printf("command= %c \n\r", command);         
+ 
+         switch (command) {
+          case '0' :
+                     pc.printf("Done\n\r");                    
+                     running = false;  
+                     break;
+                     
+          case '1' :
+                     show_menu();
+                     break;
+ 
+          case '2' :
+                     pc.printf("Hardware Reset\n\r");                                         
+                     serial_bridge.hwReset();                             //test
+                     
+                     pc.printf("Init\n\r");                                                             
+                     serial_bridge._init();                      
+                     pc.printf("Hardware Init done\n\r");                                                              
+                     break;
+          
+          case '3' :        
+                     pc.printf("IO Port Out\n\r");                    
+                     
+                     i=0;
+                     while (!pc.readable()) {
+                       serial_bridge.ioSetState(~i); 
+//                       serial_bridge.ioGetState() ;                       //test
+                       wait(0.5);
+                       pc.putc('*');                
+                       i=(i+1) & 0xFF;
+                     }
+                     
+                     pc.getc();
+                     pc.printf("IO Port Out Done\n\r");                                         
+                     break;
+ 
+          case '4' :        
+                     pc.printf("Transparant Mode, Enter '#' to quit...\n\r");                    
+                     
+                     running_test=true;
+                     
+                     while (running_test) {
+                       // From SPI/I2C to serial                       
+                       while (running_test && pc.readable()) {
+                         ch = pc.getc();
+                         running_test = (ch != '#');
+                         serial_bridge.putc(ch);
+                       }
+                       
+                       // From Serial to SPI/I2C 
+                       while (running_test && serial_bridge.readable()) {
+                         ch = serial_bridge.getc();
+                         running_test = (ch != '#');
+                         pc.putc(ch);
+                       }
+                       
+                     }
+                     
+                     pc.printf("\n\rTransparant Mode done\n\r");                                         
+                     break;
+ 
+          case '5' :        
+                     pc.printf("Available for Reading = %3d (Free Space = %3d)\n\r", serial_bridge.readableCount(), SC16IS750_FIFO_RX - serial_bridge.readableCount());                    
+                     pc.printf("Available for Writing = %3d (Used Space = %3d)\n\r", serial_bridge.writableCount(), SC16IS750_FIFO_TX - serial_bridge.writableCount());                                         
+                     break;
+ 
+          case '6' :        
+                     pc.printf("Enable RTS/CTS\n\r");
+                     serial_bridge.set_flow_control(SC16IS750::RTSCTS);
+                     break;                     
+          case '7' :        
+                     pc.printf("Disable RTS/CTS\n\r");     
+                     serial_bridge.set_flow_control(SC16IS750::Disabled);                     
+                     break;                     
+ 
+          case '8' :        
+                     pc.printf("Write block\n\r");                                                 
+                     serial_bridge.writeString("Hello World from mbed and SC16IS750 ");                     
+                     break;                     
+ 
+          case '9' :        
+                     pc.printf("Baudrate = 9600, Divisor = %d\n\r", SC16IS750_BAUDRATE_DIVISOR(9600));
+                     serial_bridge.baud(9600);                     
+                     break;                     
+ 
+          case 'A' :        
+                     pc.printf("Baudrate = 115200, Divisor = %d\n\r", SC16IS750_BAUDRATE_DIVISOR(115200));
+                     serial_bridge.baud(115200);                     
+                     break;                     
+ 
+          case 'B' :        
+                     pc.printf("Transparant Mode with buffer display, Enter '#' to quit...\n\r");                    
+                     
+                     running_test=true;
+                     
+                     while (running_test) {
+                       // From SPI/I2C to serial                       
+                       while (running_test && pc.readable()) {
+                         ch = pc.getc();
+                         running_test = (ch != '#');
+                         serial_bridge.putc(ch);
+                         
+                         // Show buffers when character was entered                         
+                         pc.printf("\n\r");
+                         pc.printf("Available for Reading = %3d (Free Space = %3d)\n\r", serial_bridge.readableCount(), SC16IS750_FIFO_RX - serial_bridge.readableCount());
+                         pc.printf("Available for Writing = %3d (Used Space = %3d)\n\r", serial_bridge.writableCount(), SC16IS750_FIFO_TX - serial_bridge.writableCount());                       
+                       }
+ 
+                       
+                       // From Serial to SPI/I2C 
+                       while (running_test && serial_bridge.readable()) {
+                         ch = serial_bridge.getc();
+                         running_test = (ch != '#');
+                         pc.putc(ch);
+                       }
+ 
+                     }
+                     
+                     pc.printf("\n\rTransparant Mode done\n\r");                                         
+                     break;
+ 
+          case 'C' :        
+                     pc.printf("Test printf() \n\r");                        
+                     
+                     serial_bridge.printf("Available for Reading = %3d (Free Space = %3d)\n\r", serial_bridge.readableCount(), SC16IS750_FIFO_RX - serial_bridge.readableCount() );                     
+                     serial_bridge.printf("Available for Writing = %3d (Used Space = %3d)\n\r", serial_bridge.writableCount(), SC16IS750_FIFO_TX - serial_bridge.writableCount());                                            
+                     
+                     pc.printf("\n\rTest printf() done\n\r");                                         
+                     break;
+          case 'D' :                             
+                     pc.printf("Test connected\n\r");           
+                     if(!serial_bridge.connected()){ 
+                       pc.printf("Failed to detect UART bridge\r\n");    
+                     }
+                     else {
+                       pc.printf("Found UART bridge!\r\n");      
+                     }
+                     break;                     
+          default :
+                     break;                     
+ 
+         } //switch
+       } //if  
+    } //while
+   
+  pc.printf("\nBye World!\n");    
+}
+ 
\ No newline at end of file

diff -r 000000000000 -r 20d8ef79d787 mbed.bld
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.bld	Wed Dec 24 01:09:26 2014 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/mbed_official/code/mbed/builds/4fc01daae5a5
\ No newline at end of file