Vergil Cola
/
MQTTGateway2
Fork of my original MQTTGateway
Diff: easy-connect/stm-spirit1-rf-driver/source/libs/spirit1/SPIRIT1_Library/Inc/SPIRIT_Irq.h
- Revision:
- 0:a1734fe1ec4b
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/easy-connect/stm-spirit1-rf-driver/source/libs/spirit1/SPIRIT1_Library/Inc/SPIRIT_Irq.h Sat Apr 08 14:43:14 2017 +0000 @@ -0,0 +1,357 @@ +/** + ****************************************************************************** + * @file SPIRIT_Irq.h + * @author VMA division - AMS + * @version 3.2.2 + * @date 08-July-2015 + * @brief Configuration and management of SPIRIT IRQs. + * + * @details + * + * On the Spirit side specific IRQs can be enabled by setting a specific bitmask. + * The Spirit libraries allow the user to do this in two different ways: + * <ul> + * + * <li>The first enables the IRQs one by one, i.e. using an SPI transaction for each + * IRQ to enable. + * + * <b>Example:</b> + * @code + * + * SpiritIrqDeInit(NULL); // this call is used to reset the IRQ mask registers + * SpiritIrq(RX_DATA_READY , S_ENABLE); + * SpiritIrq(VALID_SYNC , S_ENABLE); + * SpiritIrq(RX_TIMEOUT , S_ENABLE); + * + * @endcode + * + * </li> + * + * <li>The second strategy is to set the IRQ bitfields structure. So, during the initialization the user + * has to fill the @ref SpiritIrqs structure setting to one the single field related to the IRQ he + * wants to enable, and to zero the single field related to all the IRQs he wants to disable. + * + * <b>Example:</b> + * @code + * + * SpiritIrqs irqMask; + * + * ... + * + * SpiritIrqDeInit(&irqMask); // this call is used to reset the IRQ mask registers + * // and to set to 0x00000000 the irq mask in order to disable + * // all IRQs (disabled by default on startup) + * irqMask.IRQ_RX_DATA_READY = 1; + * irqMask.IRQ_VALID_SYNC = 1; + * irqMask.IRQ_RX_TIMEOUT = 1; + * + * ... + * @endcode + * </li> + * </ul> + * + * The most applications will require a Spirit IRQ notification on an microcontroller EXTI line. + * Then, the user can check which IRQ has been raised using two different ways. + * + * On the ISR of the EXTI line phisically linked to the Spirit pin configured for IRQ: + * + * <ul> + * <li> Check <b>only one</b> Spirit IRQ (because the Spirit IRQ status register automatically blanks itself + * after an SPI reading) into the ISR. + * + * <b>Example:</b> + * @code + * + * if(SpiritIrqCheckFlag(RX_DATA_READY)) + * { + * // do something... + * } + * + * @endcode + * </li> + * + * <li> Check more than one Spirit IRQ status by storing the entire IRQ status registers into a bitfields <i>@ref SpiritIrqs</i> structure + * and then check the interested bits. + * + * <b>Example:</b> + * @code + * + * SpiritIrqGetStatus(&irqStatus); + * + * if(irqStatus.IRQ_RX_DATA_READY) + * { + * // do something... + * } + * if(irqStatus.IRQ_VALID_SYNC) + * { + * // do something... + * } + * if(irqStatus.RX_TIMEOUT) + * { + * // do something... + * } + * + * @endcode + * </li> + * </ul> + * + + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __SPIRIT1_IRQ_H +#define __SPIRIT1_IRQ_H + + +/* Includes ------------------------------------------------------------------*/ + +#include "SPIRIT_Regs.h" +#include "SPIRIT_Types.h" + + +#ifdef __cplusplus + extern "C" { +#endif + + +/** + * @addtogroup SPIRIT_Libraries + * @{ + */ + + +/** + * @defgroup SPIRIT_Irq IRQ + * @brief Configuration and management of SPIRIT IRQs. + * @details See the file <i>@ref SPIRIT_Irq.h</i> for more details. + * @{ + */ + +/** + * @defgroup Irq_Exported_Types IRQ Exported Types + * @{ + */ + + +/** + * @brief IRQ bitfield structure for SPIRIT. This structure is used to read or write the single IRQ bit. + * During the initialization the user has to fill this structure setting to one the single field related + * to the IRQ he wants to enable, and to zero the single field related to all the IRQs he wants to disable. + * The same structure can be used to retrieve all the IRQ events from the IRQ registers IRQ_STATUS[3:0], + * and read if one or more specific IRQ raised. + * @note The fields order in the structure depends on used endianness (little or big + * endian). The actual definition is valid ONLY for LITTLE ENDIAN mode. Be sure to + * change opportunely the fields order when use a different endianness. + */ +typedef struct +{ + SpiritFlagStatus IRQ_SYNTH_LOCK_TIMEOUT:1; /*!< IRQ: only for debug; LOCK state timeout */ + SpiritFlagStatus IRQ_SYNTH_LOCK_STARTUP:1; /*!< IRQ: only for debug; see CALIBR_START_COUNTER */ + SpiritFlagStatus IRQ_SYNTH_CAL_TIMEOUT:1; /*!< IRQ: only for debug; SYNTH calibration timeout */ + SpiritFlagStatus IRQ_TX_START_TIME:1; /*!< IRQ: only for debug; TX circuitry startup time; see TX_START_COUNTER */ + SpiritFlagStatus IRQ_RX_START_TIME:1; /*!< IRQ: only for debug; RX circuitry startup time; see TX_START_COUNTER */ + SpiritFlagStatus IRQ_RX_TIMEOUT:1; /*!< IRQ: RX operation timeout */ + SpiritFlagStatus IRQ_AES_END:1; /*!< IRQ: AES End of operation */ + SpiritFlagStatus reserved:1; /*!< Reserved bit */ + + SpiritFlagStatus IRQ_READY:1; /*!< IRQ: READY state */ + SpiritFlagStatus IRQ_STANDBY_DELAYED:1; /*!< IRQ: STANDBY state after MCU_CK_CONF_CLOCK_TAIL_X clock cycles */ + SpiritFlagStatus IRQ_LOW_BATT_LVL:1; /*!< IRQ: Battery level below threshold*/ + SpiritFlagStatus IRQ_POR:1; /*!< IRQ: Power On Reset */ + SpiritFlagStatus IRQ_BOR:1; /*!< IRQ: Brown out event (both accurate and inaccurate)*/ + SpiritFlagStatus IRQ_LOCK:1; /*!< IRQ: LOCK state */ + SpiritFlagStatus IRQ_PM_COUNT_EXPIRED:1; /*!< IRQ: only for debug; Power Management startup timer expiration (see reg PM_START_COUNTER, 0xB5) */ + SpiritFlagStatus IRQ_XO_COUNT_EXPIRED:1; /*!< IRQ: only for debug; Crystal oscillator settling time counter expired */ + + SpiritFlagStatus IRQ_TX_FIFO_ALMOST_EMPTY:1; /*!< IRQ: TX FIFO almost empty */ + SpiritFlagStatus IRQ_RX_FIFO_ALMOST_FULL:1; /*!< IRQ: RX FIFO almost full */ + SpiritFlagStatus IRQ_RX_FIFO_ALMOST_EMPTY:1; /*!< IRQ: RX FIFO almost empty */ + SpiritFlagStatus IRQ_MAX_BO_CCA_REACH:1; /*!< IRQ: Max number of back-off during CCA */ + SpiritFlagStatus IRQ_VALID_PREAMBLE:1; /*!< IRQ: Valid preamble detected */ + SpiritFlagStatus IRQ_VALID_SYNC:1; /*!< IRQ: Sync word detected */ + SpiritFlagStatus IRQ_RSSI_ABOVE_TH:1; /*!< IRQ: RSSI above threshold */ + SpiritFlagStatus IRQ_WKUP_TOUT_LDC:1; /*!< IRQ: Wake-up timeout in LDC mode */ + + SpiritFlagStatus IRQ_RX_DATA_READY:1; /*!< IRQ: RX data ready */ + SpiritFlagStatus IRQ_RX_DATA_DISC:1; /*!< IRQ: RX data discarded (upon filtering) */ + SpiritFlagStatus IRQ_TX_DATA_SENT:1; /*!< IRQ: TX data sent */ + SpiritFlagStatus IRQ_MAX_RE_TX_REACH:1; /*!< IRQ: Max re-TX reached */ + SpiritFlagStatus IRQ_CRC_ERROR:1; /*!< IRQ: CRC error */ + SpiritFlagStatus IRQ_TX_FIFO_ERROR:1; /*!< IRQ: TX FIFO underflow/overflow error */ + SpiritFlagStatus IRQ_RX_FIFO_ERROR:1; /*!< IRQ: RX FIFO underflow/overflow error */ + SpiritFlagStatus IRQ_TX_FIFO_ALMOST_FULL:1; /*!< IRQ: TX FIFO almost full */ +} SpiritIrqs; + +// betzw: uint32_t masks +#define IRQ_TX_FIFO_ALMOST_EMPTY_MASK (0x00010000) /* (1<<16) */ +#define IRQ_RX_FIFO_ALMOST_FULL_MASK (0x00020000) /* (1<<17) */ +#define IRQ_VALID_SYNC_MASK (0x00200000) /* (1<<21) */ +#define IRQ_RX_DATA_READY_MASK (0x01000000) /* (1<<24) */ +#define IRQ_RX_DATA_DISC_MASK (0x02000000) /* (1<<25) */ +#define IRQ_TX_DATA_SENT_MASK (0x04000000) /* (1<<26) */ +#define IRQ_TX_FIFO_ERROR_MASK (0x20000000) /* (1<<29) */ +#define IRQ_RX_FIFO_ERROR_MASK (0x40000000) /* (1<<30) */ + +/** + * @brief IRQ list enumeration for SPIRIT. This enumeration type can be used to address a + * specific IRQ. + */ +typedef enum +{ + RX_DATA_READY = 0x00000001, /*!< IRQ: RX data ready */ + RX_DATA_DISC = 0x00000002, /*!< IRQ: RX data discarded (upon filtering) */ + TX_DATA_SENT = 0x00000004, /*!< IRQ: TX data sent */ + MAX_RE_TX_REACH = 0x00000008, /*!< IRQ: Max re-TX reached */ + CRC_ERROR = 0x00000010, /*!< IRQ: CRC error */ + TX_FIFO_ERROR = 0x00000020, /*!< IRQ: TX FIFO underflow/overflow error */ + RX_FIFO_ERROR = 0x00000040, /*!< IRQ: RX FIFO underflow/overflow error */ + TX_FIFO_ALMOST_FULL = 0x00000080, /*!< IRQ: TX FIFO almost full */ + TX_FIFO_ALMOST_EMPTY = 0x00000100, /*!< IRQ: TX FIFO almost empty */ + RX_FIFO_ALMOST_FULL = 0x00000200, /*!< IRQ: RX FIFO almost full */ + RX_FIFO_ALMOST_EMPTY = 0x00000400, /*!< IRQ: RX FIFO almost empty */ + MAX_BO_CCA_REACH = 0x00000800, /*!< IRQ: Max number of back-off during CCA */ + VALID_PREAMBLE = 0x00001000, /*!< IRQ: Valid preamble detected */ + VALID_SYNC = 0x00002000, /*!< IRQ: Sync word detected */ + RSSI_ABOVE_TH = 0x00004000, /*!< IRQ: RSSI above threshold */ + WKUP_TOUT_LDC = 0x00008000, /*!< IRQ: Wake-up timeout in LDC mode */ + READY = 0x00010000, /*!< IRQ: READY state */ + STANDBY_DELAYED = 0x00020000, /*!< IRQ: STANDBY state after MCU_CK_CONF_CLOCK_TAIL_X clock cycles */ + LOW_BATT_LVL = 0x00040000, /*!< IRQ: Battery level below threshold*/ + POR = 0x00080000, /*!< IRQ: Power On Reset */ + BOR = 0x00100000, /*!< IRQ: Brown out event (both accurate and inaccurate)*/ + LOCK = 0x00200000, /*!< IRQ: LOCK state */ + PM_COUNT_EXPIRED = 0x00400000, /*!< IRQ: only for debug; Power Management startup timer expiration (see reg PM_START_COUNTER, 0xB5) */ + XO_COUNT_EXPIRED = 0x00800000, /*!< IRQ: only for debug; Crystal oscillator settling time counter expired */ + SYNTH_LOCK_TIMEOUT = 0x01000000, /*!< IRQ: only for debug; LOCK state timeout */ + SYNTH_LOCK_STARTUP = 0x02000000, /*!< IRQ: only for debug; see CALIBR_START_COUNTER */ + SYNTH_CAL_TIMEOUT = 0x04000000, /*!< IRQ: only for debug; SYNTH calibration timeout */ + TX_START_TIME = 0x08000000, /*!< IRQ: only for debug; TX circuitry startup time; see TX_START_COUNTER */ + RX_START_TIME = 0x10000000, /*!< IRQ: only for debug; RX circuitry startup time; see TX_START_COUNTER */ + RX_TIMEOUT = 0x20000000, /*!< IRQ: RX operation timeout */ + AES_END = 0x40000000, /*!< IRQ: AES End of operation */ + ALL_IRQ = 0x7FFFFFFF /*!< All the above mentioned IRQs */ + +} IrqList; + +#define IS_SPIRIT_IRQ_LIST(VALUE) ((VALUE == RX_DATA_READY) || \ + (VALUE == RX_DATA_DISC) || \ + (VALUE == TX_DATA_SENT) || \ + (VALUE == MAX_RE_TX_REACH) || \ + (VALUE == CRC_ERROR) || \ + (VALUE == TX_FIFO_ERROR) || \ + (VALUE == RX_FIFO_ERROR) || \ + (VALUE == TX_FIFO_ALMOST_FULL) || \ + (VALUE == TX_FIFO_ALMOST_EMPTY) || \ + (VALUE == RX_FIFO_ALMOST_FULL) || \ + (VALUE == RX_FIFO_ALMOST_EMPTY) || \ + (VALUE == MAX_BO_CCA_REACH) || \ + (VALUE == VALID_PREAMBLE) || \ + (VALUE == VALID_SYNC) || \ + (VALUE == RSSI_ABOVE_TH) || \ + (VALUE == WKUP_TOUT_LDC) || \ + (VALUE == READY) || \ + (VALUE == STANDBY_DELAYED) || \ + (VALUE == LOW_BATT_LVL) || \ + (VALUE == POR) || \ + (VALUE == BOR) || \ + (VALUE == LOCK) || \ + (VALUE == PM_COUNT_EXPIRED) || \ + (VALUE == XO_COUNT_EXPIRED) || \ + (VALUE == SYNTH_LOCK_TIMEOUT) || \ + (VALUE == SYNTH_LOCK_STARTUP) || \ + (VALUE == SYNTH_CAL_TIMEOUT) || \ + (VALUE == TX_START_TIME) || \ + (VALUE == RX_START_TIME) || \ + (VALUE == RX_TIMEOUT) || \ + (VALUE == AES_END) || \ + (VALUE == ALL_IRQ )) + + +/** + * @} + */ + + +/** + * @defgroup Irq_Exported_Constants IRQ Exported Constants + * @{ + */ + + +/** + * @} + */ + + +/** + * @defgroup Irq_Exported_Macros IRQ Exported Macros + * @{ + */ + + +/** + * @} + */ + + +/** + * @defgroup Irq_Exported_Functions IRQ Exported Functions + * @{ + */ + +void SpiritIrqDeInit(SpiritIrqs* pxIrqInit); +void SpiritIrqInit(SpiritIrqs* pxIrqInit); +void SpiritIrq(IrqList xIrq, SpiritFunctionalState xNewState); +void SpiritIrqGetMask(SpiritIrqs* pxIrqMask); +void SpiritIrqGetStatus(SpiritIrqs* pxIrqStatus); +void SpiritIrqClearStatus(void); +SpiritBool SpiritIrqCheckFlag(IrqList xFlag); + +/** + * @} + */ + +/** + * @} + */ + + +/** + * @} + */ + + +#ifdef __cplusplus +} +#endif + +#endif + +/******************* (C) COPYRIGHT 2015 STMicroelectronics *****END OF FILE****/