Diff: UniGraphic/Inits/IST3020.cpp

Revision:

12:9a20164dcc47

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/UniGraphic/Inits/IST3020.cpp	Wed Jan 11 11:41:30 2017 +0000
@@ -0,0 +1,78 @@
+ /* mbed UniGraphic library - Device specific class
+ * Copyright (c) 2015 Giuliano Dianda
+ * Released under the MIT License: http://mbed.org/license/mit
+ */
+#include "Protocols.h"
+#include "IST3020.h"
+
+/*this is a quite standard config, similar to ST7565, except bigger screen and diff resistor ratio value*/
+
+//////////////////////////////////////////////////////////////////////////////////
+// display settings ///////////////////////////////////////////////////////
+/////////////////////////////////////////////////////////////////////////
+#define IC_X_SEGS    256 // IST3020 SEG has range 0-255 (255-0 if ADC=1), check your datasheet, important for the orientation
+#define IC_Y_COMS    64  // IST3020 COM has range 0-63 (63-0 if SHL=1), check your datasheet, important for the orientation
+// put in constructor
+//#define LCDSIZE_X       192 // display X pixels, IST3020 is advertised as 224x65 but display size could be smaller
+//#define LCDSIZE_Y       64  // display Y pixels, the 65th is for accessing "icons"
+
+
+
+IST3020::IST3020(proto_t displayproto, PortName port, PinName CS, PinName reset, PinName DC, PinName WR, PinName RD, const char *name, unsigned int LCDSIZE_X, unsigned  int LCDSIZE_Y)
+    : LCD(displayproto, port, CS, reset, DC, WR, RD, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
+{
+    hw_reset();
+    BusEnable(true);
+    init();
+    cls();
+    set_orientation(1);
+    locate(0,0);
+}
+IST3020::IST3020(proto_t displayproto, int Hz, PinName mosi, PinName miso, PinName sclk, PinName CS, PinName reset, PinName DC, const char *name, unsigned int LCDSIZE_X, unsigned  int LCDSIZE_Y)
+    : LCD(displayproto, Hz, mosi, miso, sclk, CS, reset, DC, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
+{
+    hw_reset();
+    BusEnable(true);
+    init();
+    cls();
+    set_orientation(1);
+    locate(0,0);
+}
+// reset and init the lcd controller
+// init sequence is manufacturer specific
+void IST3020::init()
+{
+    /* Start Initial Sequence ----------------------------------------------------*/
+    
+    wr_cmd8(0xE2);   //  sw reset
+    wait_ms(10);
+    
+    wr_cmd8(0xAE);   //  display off
+    wr_cmd8(0xAB);   //  built-in OSC on
+    wr_cmd8(0xA2);   //  bias voltage (1/9)
+  //  wr_cmd8(0xA3);   //  bias voltage (1/7)
+
+    wr_cmd8(0xA0);   // ADC select seg0-seg223
+    //wr_cmd8(0xA1);   // ADC select seg223-seg0
+    wr_cmd8(0xC8);   // SHL select com63-com0
+    //wr_cmd8(0xC0);   // SHL select com0-com63
+
+    wr_cmd8(0x2C);   //  Internal Voltage Converter ON
+    wait_ms(10);
+    wr_cmd8(0x2E);   //  Internal Voltage Regulator ON
+    wait_ms(10);
+    wr_cmd8(0x2F);   //  Internal Voltage Follower ON
+    wait_ms(10);
+    wr_cmd8(0x20);   //  Regulor_Resistor_Select resistor ratio 20-27 20=4.5(default) 27=8.0, 0.5 steps
+    set_contrast(46);
+    //wr_cmd8(0x81);   //  set contrast (reference voltage register set)
+    //wr_cmd8(0x20);   //  contrast 00-3F default 20
+    
+    wr_cmd8(0xA4);   //  LCD display ram (EntireDisplayOn disable)
+    //wr_cmd8(0x70);   //  External Capacitors Discharge function enable (should be enabled by default)
+    //wr_cmd8(0x77);   //  External Capacitors Discharge function disable
+    wr_cmd8(0x40);   // start line = 0
+    wr_cmd8(0xA6);     // display normal (1 = illuminated)
+    wr_cmd8(0xAF);     // display ON 
+
+}
\ No newline at end of file