vghjvghi
Fork of XBeeLib3 by
XBeeDM/XBeeDM.h
- Committer:
- vinceP
- Date:
- 2017-12-05
- Revision:
- 11:d7dc0e97d47e
- Parent:
- 9:780db84ce891
File content as of revision 11:d7dc0e97d47e:
/** * Copyright (c) 2015 Digi International Inc., * All rights not expressly granted are reserved. * * This Source Code Form is subject to the terms of the Mozilla Public * License, v. 2.0. If a copy of the MPL was not distributed with this file, * You can obtain one at http://mozilla.org/MPL/2.0/. * * Digi International Inc. 11001 Bren Road East, Minnetonka, MN 55343 * ======================================================================= */ #if !defined(__XBEE_DM_H_) #define __XBEE_DM_H_ #include "XBee/XBee.h" #include "FrameHandlers/FH_AtCmdResp.h" #include "FrameHandlers/FH_RxPacketDM.h" #include "FrameHandlers/FH_IoDataSampleDM.h" #include "RemoteXBee/RemoteXBee.h" namespace XBeeLib { /** Class for XBee ZigBee modules, derived from XBee */ class XBeeDM : public XBee { public: /** * IoLine for XBeeDM Modules */ enum IoLine { DIO0_AD0 = 0, /**< DIO0_AD0 pin */ DIO1_AD1 = 1, /**< DIO1_AD1 pin */ DIO2_AD2 = 2, /**< DIO2_AD2 pin */ DIO3_AD3 = 3, /**< DIO3_AD3 pin */ DIO4 = 4, /**< DIO4 pin */ DIO5 = 5, /**< DIO5 pin */ DIO6 = 6, /**< DIO6 pin */ DIO7 = 7, /**< DIO7 pin */ DIO8 = 8, /**< DIO8 pin */ DIO9 = 9, /**< DIO9 pin */ DIO10_PWM0 = 10, /**< DIO10_PWM0 pin */ DIO11_PWM1 = 11, /**< DIO11_PWM1 pin */ DIO12 = 12 /**< DIO12 pin */ }; /** Class constructor * @param tx the TX pin of the UART that will interface the XBee module * @param rx the RX pin of the UART that will interface the XBee module * @param reset the pin to which the XBee's reset line is attached to, use NC if not available * @param rts the RTS pin for the UART that will interface the XBee module, use NC if not available * @param cts the CTS pin for the UART that will interface the XBee module, use NC if not available * @param baud the baudrate for the UART that will interface the XBee module. Note that the module has to be already configured * to this baud rate (ATBD parameter). By default it is configured to 9600 bps */ XBeeDM(PinName tx, PinName rx, PinName reset = NC, PinName rts = NC, PinName cts = NC, int baud = 9600); /** Class destructor */ virtual ~XBeeDM(); /** init- initializes object * This function must be called just after creating the object so it initializes internal data. * @returns * Success if the module has been properly initialized and is ready to process data. * Failure otherwise. */ RadioStatus init(); /** set_channel - sets the channel number * * @param channel the channel in which the radio operates. Range is 0x0B - 0x1A for XBee and 0x0C - 0x17 for XBee-PRO. * The Center Frequency = 2.405 + (CH - 11) * 5 MHz * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_channel(uint8_t channel); /** get_channel - gets the channel number * * @param channel pointer where the channel value will be stored. * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus get_channel(uint8_t * const channel); /** set_network_id - sets the Network ID. * * @param network_id the Network ID value that will be set on the radio * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_network_id(uint16_t network_id); /** get_network_id - gets the Network ID, as it was set by @ref set_network_id(). * * @param network_id pointer where the Network ID will be stored * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus get_network_id(uint16_t * const network_id); /** register_node_discovery_cb - registers the callback function that will be called * when the responses to the node discovery command arrive * * @param function function pointer with the callback function */ void register_node_discovery_cb(node_discovery_dm_cb_t function); /** unregister_node_discovery_cb - removes the node discovery callback */ void unregister_node_discovery_cb(); /** register_receive_cb - registers the callback function that will be called * when a data packet is received * * @param function function pointer with the callback function */ void register_receive_cb(receive_dm_cb_t function); /** unregister_receive_cb - removes the rx packet callback */ void unregister_receive_cb(); /** register_io_sample_cb - registers the callback function that will be called * when a IO Sample Data packet is received * * @param function function pointer with the callback function */ void register_io_sample_cb(io_data_cb_dm_t function); /** unregister_io_sample_cb - removes the IO Sample Data reception callback */ void unregister_io_sample_cb(); /*********************** send_data member methods ************************/ /** send_data - sends data to a remote device * * @param remote remote device * @param data pointer to the data that will be sent * @param len number of bytes that will be transmitted * @param syncr if true, method waits for the packet answer with the result of the operation * @returns the result of the data transfer * TxStatusSuccess if the operation was successful, * the error code otherwise */ virtual TxStatus send_data(const RemoteXBee& remote, const uint8_t *const data, uint16_t len, bool syncr = true); /** send_data - sends data to a remote device. This method uses * the explicit addressing frame, allowing to use source and * destination end points and cluster and profile IDs * * @param remote remote device * @param source_ep source end point * @param dest_ep destination end point * @param cluster_id cluster ID * @param profile_id profile ID * @param data pointer to the data that will be sent * @param len number of bytes that will be transmitted * @param syncr if true, method waits for the packet answer with the result of the operation * @returns the result of the data transfer * TxStatusSuccess if the operation was successful, * the error code otherwise */ TxStatus send_data(const RemoteXBee& remote, uint8_t source_ep, uint8_t dest_ep, uint16_t cluster_id, uint16_t profile_id, const uint8_t *const data, uint16_t len, bool syncr = true); /** send_data_to_coordinator - sends data to the ZigBee coordinator * * @param data pointer to the data that will be sent * @param len number of bytes that will be transmitted * @param syncr if true, method waits for the packet answer with the result of the operation * @returns the result of the data transfer * TxStatusSuccess if the operation was successful, * the error code otherwise */ TxStatus send_data_to_coordinator(const uint8_t *const data, uint16_t len, bool syncr = true); /** get_remote_node_by_id - searches for a device in the network with the specified Node Identifier. * * @param node_id node id of the device we are looking for * @returns a RemoteXBeeDM with the 16-bit and 64-bit address of the remote device whose node id matches with the parameter. * If node is not found, the returned object will have invalid addresses (RemoteXBeeDM::is_valid() will return false). */ RemoteXBeeDM get_remote_node_by_id(const char * const node_id); /* Allow using XBee::set_param() methods for local radio from this class */ using XBee::set_param; /** set_param - sets a parameter in a remote radio by sending an AT command and waiting for the response. * * @param remote remote device * @param param parameter to be set. * @param data the parameter value (4 bytes) to be set. * @returns the command response status. */ virtual AtCmdFrame::AtCmdResp set_param(const RemoteXBee& remote, const char * const param, uint32_t data); /** set_param - sets a parameter in a remote radio by sending an AT command and waiting for the response. * * @param remote remote device * @param param parameter to be set. * @param data the parameter value byte array (len bytes) to be set. * @param len number of bytes of the parameter value. * @returns the command response status. */ virtual AtCmdFrame::AtCmdResp set_param(const RemoteXBee& remote, const char * const param, const uint8_t * data = NULL, uint16_t len = 0); /* Allow using XBee::get_param() methods for local radio from this class */ using XBee::get_param; /** get_param - gets a parameter from a remote radio by sending an AT command and waiting for the response. * * @param remote remote device * @param param parameter to be get. * @param data pointer where the param value (4 bytes) will be stored. * @returns the command response status. */ virtual AtCmdFrame::AtCmdResp get_param(const RemoteXBee& remote, const char * const param, uint32_t * const data); /** get_param - gets a parameter from a remote radio by sending an AT command and waiting for the response. * * @param remote remote device * @param param parameter to be get. * @param data pointer where the param value (n bytes) will be stored. * @param len pointer where the number of bytes of the param value will be stored. * @returns the command response status. */ virtual AtCmdFrame::AtCmdResp get_param(const RemoteXBee& remote, const char * const param, uint8_t * const data, uint16_t * const len); /************************* IO member methods **************************/ /** set_pin_config - configures a radio IO line * * @param remote remote device * @param line IO line being configured * @param mode configuration mode for the selected line * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_pin_config(const RemoteXBee& remote, IoLine line, IoMode mode); /** get_pin_config - gets the configuration of a radio IO line * * @param remote remote device * @param line IO line being read to get its configuration * @param mode pointer where the configuration will be stored * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus get_pin_config(const RemoteXBee& remote, IoLine line, IoMode * const mode); /** set_dio - sets to low/high a DIO line * * @param remote remote device * @param line DIO line being set * @param val value that will be set in the DIO line * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_dio(const RemoteXBee& remote, IoLine line, DioVal val); /** get_dio - read the value of a DIO configured as digital input * * @param remote remote device * @param line DIO line being read * @param val pointer where the DIO value read will be stored * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus get_dio(const RemoteXBee& remote, IoLine line, DioVal * const val); /** get_adc - read the value of the espcified ADC line * * @param remote remote device * @param line ADC line being read * @param val pointer where the value read from hte ADC will be stored * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus get_adc(const RemoteXBee& remote, IoLine line, uint16_t * const val); /** get_iosample - retrieves an @ref IOSampleDM from a remote node. This object can be used to get the remote node's ADC and DIO values. * * @param remote remote device * @returns IOSampleDM object with the remote node's DIO and ADC values. */ IOSampleDM get_iosample(const RemoteXBee& remote); /** set_pwm - sets the duty cycle of a PWM line * * @param remote remote device * @param line PWM line being set * @param duty_cycle duty cycle that will be set in the PWM line * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_pwm(const RemoteXBee& remote, IoLine line, float duty_cycle); /** set_pin_pull_up - enables or disables the internal pull-up resistor of a line * * @param remote remote device * @param line line being configured for pull-up * @param enable whether to enable the internal pull-up resistor. * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus set_pin_pull_up(const RemoteXBee& remote, IoLine line, bool enable); /** enable_dio_change_detection - enables or disables the notification when a change is detected in a digital input line. * In other words, it will force an IO Sample transmission when the DIO state changes. Only for DIO0 to DIO11. * * @param remote remote device * @param line line being configured for pull-up * @param enable whether to enable the internal pull-up resistor. * @returns * Success if the operation was successful, * Failure otherwise */ RadioStatus enable_dio_change_detection(const RemoteXBee& remote, IoLine line, bool enable); /** config_poll_destination - configures to which node poll messages will be sent once module awakes if configured as * an Indirect Msg Poller (CE==0x4). * Consult the module's reference manual for more information. * * @param destination remote device where the poll messages will be sent * @returns the result of the data transfer * Success if the operation was successful, * Failure otherwise */ RadioStatus config_poll_destination(const RemoteXBee& destination); protected: /** Frame handler used for the node discovery. Registered when a callback function * is registered */ FH_NodeDiscoveryDM *_nd_handler; /** Frame handler used for the rx packets. Automatically registered when a callback * function is registered */ FH_RxPacketDM *_rx_pkt_handler; /** Frame handler used for the IO Data Sample packets. Automatically registered when a callback * function is registered */ FH_IoDataSampeDM *_io_data_handler; /** Method called directly by the library when a modem status frame is received to * update the internal status variables */ virtual void radio_status_update(AtCmdFrame::ModemStatus modem_status); /* Allow using XBee::send_data() methods from this class */ using XBee::send_data; /** get_node_discovery_timeout - gets the node discovery timeout * * @param timeout_ms pointer where the node discovery timeout value will be stored * @param wait_for_complete_timeout pointer where the function will store if the operator * has to wait for the complete nd timeout after issuing * a directed nd request * @returns * Success if the operation was successful, * Failure otherwise */ virtual RadioStatus get_node_discovery_timeout(uint16_t * const timeout_ms); virtual RadioStatus get_node_discovery_timeout(uint16_t * const timeout_ms, bool * const wait_for_complete_timeout); }; } /* namespace XBeeLib */ #endif /* __XBEE_DM_H_ */