Uttam Bhat / Mbed 2 deprecated Training-Aug2018-SX1272-X-NUCLEO-IKS01A2

Create Application using SX1272 + X-NUCLEO-IKS01A2

Dependencies:   X_NUCLEO_IKS01A2 driver_mbed_TH02 mbed LoRaWAN-lib-v1_0_1 SX1272Lib

Fork of LoRaWAN-SX1272-Application-Demo by Semtech

LoRaWAN-NAMote72 Application Demo is a Class-A device example project using LoRaWAN-lib and SX1272Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_APPLICATION_EUI (8 Bytes)
• LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

Activation by Personalization (ABP) can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_NWKSKEY (16 Bytes)
• LORAWAN_APPSKEY (16 Bytes)

Config.h (LoRaWAN Communication Parameters)

• Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled

• Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled

• Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE

• Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.

• Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4

• Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.

• ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.

• Application Port : The application port can be set using parameter LORAWAN_APP_PORT.

• Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE

• Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

Main.cpp (Device State Machine)

The end-device state machine is defined.

• Initial State : Device is initialized.

• Join State : For OTA, Join Request is transmitted to the network until Join Accept is received by the end-device. Join event function is called that sets Red LED ON.

• Send State : Transmit payload frame is prepared. Tx event is called that blinks the Red LED indicating uplink transmission.

• Cycle State : Next packet transmission is scheduled

LoRaEventProc.cpp (Events and On-board Application)

Define events during Join, Tx & Rx. Prepare TX packet by appending with appropriate application data.

• PrepareLoRaFrame(uint8_t port ) : Prepare LoRa payload frame with on-board application data such as GPS, Temperature, Battery, etc. LoRa.ApplicationCall(AppType ) calls application AppType defined in LoRaApp.cpp. AppType is defined in LoRaApp.h

LoRaApp.cpp

User-defined applications such as GPS, Temp, Accelerometer, LED indications etc. Event based actions such as LED blink on Tx, LED toggle on downlink etc

LoRaDeviceStateProc.cpp

Process function calls corresponding to different Device states

LoRaMacLayerService.cpp

Define MAC Layer Services: MLME & MCPS

/*
 / _____)             _              | |
( (____  _____ ____ _| |_ _____  ____| |__
 \____ \| ___ |    (_   _) ___ |/ ___)  _ \
 _____) ) ____| | | || |_| ____( (___| | | |
(______/|_____)_|_|_| \__)_____)\____)_| |_|
    (C)2013 Semtech

Description: Helper functions implementation

License: Revised BSD License, see LICENSE.TXT file include in the project

Maintainer: Miguel Luis and Gregory Cristian
*/
#ifndef __UTILITIES_H__
#define __UTILITIES_H__

/*!
 * \brief Returns the minimum value betwen a and b
 *
 * \param [IN] a 1st value
 * \param [IN] b 2nd value
 * \retval minValue Minimum value
 */
#define MIN( a, b ) ( ( ( a ) < ( b ) ) ? ( a ) : ( b ) )

/*!
 * \brief Returns the maximum value betwen a and b
 *
 * \param [IN] a 1st value
 * \param [IN] b 2nd value
 * \retval maxValue Maximum value
 */
#define MAX( a, b ) ( ( ( a ) > ( b ) ) ? ( a ) : ( b ) )

/*!
 * \brief Returns 2 raised to the power of n
 *
 * \param [IN] n power value
 * \retval result of raising 2 to the power n
 */
#define POW2( n ) ( 1 << n )

/*!
 * \brief Initializes the pseudo ramdom generator initial value
 *
 * \param [IN] seed Pseudo ramdom generator initial value
 */
void srand1( uint32_t seed );

/*!
 * \brief Computes a random number between min and max
 *
 * \param [IN] min range minimum value
 * \param [IN] max range maximum value
 * \retval random random value in range min..max
 */
int32_t randr( int32_t min, int32_t max );

/*!
 * \brief Copies size elements of src array to dst array
 * 
 * \remark STM32 Standard memcpy function only works on pointers that are aligned
 *
 * \param [OUT] dst  Destination array
 * \param [IN]  src  Source array
 * \param [IN]  size Number of bytes to be copied
 */
void memcpy1( uint8_t *dst, const uint8_t *src, uint16_t size );

/*!
 * \brief Copies size elements of src array to dst array reversing the byte order
 *
 * \param [OUT] dst  Destination array
 * \param [IN]  src  Source array
 * \param [IN]  size Number of bytes to be copied
 */
void memcpyr( uint8_t *dst, const uint8_t *src, uint16_t size );

/*!
 * \brief Set size elements of dst array with value 
 * 
 * \remark STM32 Standard memset function only works on pointers that are aligned
 *
 * \param [OUT] dst   Destination array
 * \param [IN]  value Default value
 * \param [IN]  size  Number of bytes to be copied
 */
void memset1( uint8_t *dst, uint8_t value, uint16_t size );

/*!
 * \brief Converts a nibble to an hexadecimal character
 * 
 * \param [IN] a   Nibble to be converted
 * \retval hexChar Converted hexadecimal character
 */
int8_t Nibble2HexChar( uint8_t a );

#endif // __UTILITIES_H__