Uttam Bhat / Mbed 2 deprecated Training-Aug2018-SX1272-X-NUCLEO-IKS01A2

Create Application using SX1272 + X-NUCLEO-IKS01A2

Dependencies:   X_NUCLEO_IKS01A2 driver_mbed_TH02 mbed LoRaWAN-lib-v1_0_1 SX1272Lib

Fork of LoRaWAN-SX1272-Application-Demo by Semtech

LoRaWAN-NAMote72 Application Demo is a Class-A device example project using LoRaWAN-lib and SX1272Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_APPLICATION_EUI (8 Bytes)
• LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

Activation by Personalization (ABP) can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_NWKSKEY (16 Bytes)
• LORAWAN_APPSKEY (16 Bytes)

Config.h (LoRaWAN Communication Parameters)

• Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled

• Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled

• Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE

• Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.

• Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4

• Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.

• ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.

• Application Port : The application port can be set using parameter LORAWAN_APP_PORT.

• Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE

• Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

Main.cpp (Device State Machine)

The end-device state machine is defined.

• Initial State : Device is initialized.

• Join State : For OTA, Join Request is transmitted to the network until Join Accept is received by the end-device. Join event function is called that sets Red LED ON.

• Send State : Transmit payload frame is prepared. Tx event is called that blinks the Red LED indicating uplink transmission.

• Cycle State : Next packet transmission is scheduled

LoRaEventProc.cpp (Events and On-board Application)

Define events during Join, Tx & Rx. Prepare TX packet by appending with appropriate application data.

• PrepareLoRaFrame(uint8_t port ) : Prepare LoRa payload frame with on-board application data such as GPS, Temperature, Battery, etc. LoRa.ApplicationCall(AppType ) calls application AppType defined in LoRaApp.cpp. AppType is defined in LoRaApp.h

LoRaApp.cpp

User-defined applications such as GPS, Temp, Accelerometer, LED indications etc. Event based actions such as LED blink on Tx, LED toggle on downlink etc

LoRaDeviceStateProc.cpp

Process function calls corresponding to different Device states

LoRaMacLayerService.cpp

Define MAC Layer Services: MLME & MCPS

/*
 / _____)             _              | |
( (____  _____ ____ _| |_ _____  ____| |__
 \____ \| ___ |    (_   _) ___ |/ ___)  _ \
 _____) ) ____| | | || |_| ____( (___| | | |
(______/|_____)_|_|_| \__)_____)\____)_| |_|
    (C)2015 Semtech

Description: Target board general functions implementation

License: Revised BSD License, see LICENSE.TXT file include in the project

Maintainer: Miguel Luis and Gregory Cristian
*/
#ifndef __BOARD_H__
#define __BOARD_H__

#include "Config.h"
#include "mbed.h"
#include "system/timer.h"
#include "debug.h"
#include "system/utilities.h"
#include "sx1272-hal.h"

#ifdef USE_GROVE_SENSOR
// Grove temperature-humidity sensor
#include "driver_mbed_TH02.h"
#endif

#ifdef USE_IKS01A1_SENSOR
#include "x_nucleo_iks01a1.h"
#endif

/*!
 * Unique Devices IDs register set ( STM32L1xxx )
 */
#define         ID1                                 ( 0x1FF800D0 )
#define         ID2                                 ( 0x1FF800D4 )
#define         ID3                                 ( 0x1FF800E4 )

#define LOW_BAT_THRESHOLD   3.45
#define AIN_VREF            3.3     // STM32 internal refernce
#define AIN_VBAT_DIV        2       // Resistor divider

extern SX1272MB2xAS Radio;

extern DigitalIn UsrButton;

extern DigitalOut Led;

#ifdef USE_IKS01A1_SENSOR
extern X_NUCLEO_IKS01A1 *mems_expansion_board;
extern MotionSensor *accelerometer;
extern HumiditySensor *humidity_sensor;
extern PressureSensor *pressure_sensor;
extern TempSensor *temp_sensor1;
extern TempSensor *temp_sensor2;
#endif

/*!
 * \brief Initializes the target board peripherals.
 */
void BoardInit( void );

/*!
 * \brief Measure the Battery level
 *
 * \retval value  battery level ( 0: very low, 254: fully charged )
 */
uint8_t BoardGetBatteryLevel( void );

/*!
 * Returns a pseudo random seed generated using the MCU Unique ID
 *
 * \retval seed Generated pseudo random seed
 */
uint32_t BoardGetRandomSeed( void );

/*!
 * \brief Generates Lower 32 bits of DEVEUI using 96 bits unique device ID 
 *
 * \param [IN] id Pointer to an array that will contain the Unique ID
 */
void BoardGetDevEUI( uint8_t *id );

/*!
 * \brief Gets the board 64 bits unique ID 
 *
 * \param [IN] id Pointer to an array that will contain the Unique ID
 */
void BoardGetUniqueId( uint8_t *id );

#endif // __BOARD_H__