Uttam Bhat
SX1276 Shield based Applications
Dependencies: X_NUCLEO_IKS01A1 LoRaWAN-lib SX1276Lib mbed
LoRaWAN-SX1276-Application Demo uses SX1276MB1LAS mbed component shield on a nucleo board platform to demonstrate a Class-A LoRaWAN device in the 915MHz ISM band for North American region. It uses the LoRaWAN-lib and SX1276Lib libraries.
Comissioning.h (LoRaWAN Network Configuration)
The end-device can be activated in one of the two ways:
Over the Air (OTA) activation can be enabled as shown in the figure below.
The end-device must be configured with the following parameters:
LORAWAN_DEVICE_EUI(8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-deviceLORAWAN_APPLICATION_EUI(8 Bytes)LORAWAN_APPLICATION_KEY(or DEVKEY) (16 Bytes)
Activation by Personalization (ABP) can be enabled as shown in the figure below.
The end-device must be configured with the following parameters:
LORAWAN_DEVICE_ADDRESS(4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-deviceLORAWAN_NWKSKEY(16 Bytes)LORAWAN_APPSKEY(16 Bytes)
Config.h (LoRaWAN Communication Parameters)
- Mode of Operation : Hybrid
If the end-device needs to be configured to operate over 8-channels, then
Hybrid Modeneeds to be enabled
- Mode of Operation : Frequency Hop
If the end-device needs to be configured to operate over 64-channels, then
Hybrid Modeneeds to be disabled
- Delay between successive JOIN REQUESTs :
The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter
OVER_THE_AIR_ACTIVATION_DUTYCYCLE
- Inter-Frame Delay :
One can change the delay between each frame transmission using
APP_TX_DUTYCYCLEIt is advisable thatAPP_TX_DUTYCYCLEis greater than or equal to 3sec.
- Data Rate :
The data rate can be configured as per LoRaWAN specification using the paramter
LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4
- Confirmed/Unconfirmed Messages :
The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter
LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with anACKby the network server in the subsequent RX window. When set to 0, noACKis requested.
- ADR ON/OFF :
The ADR can be enabled or disabled using the parameter
LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.
- Application Port :
The application port can be set using parameter
LORAWAN_APP_PORT. A few examples are associated to specific Application Port, and are defined in Config.h
- Payload Length :
The lenght of the payload (in bytes) to be transmitted can be configured using
LORAWAN_APP_DATA_SIZE
- Transmit Power :
The transmit power can be configured using
LORAWAN_TX_POWER(LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)
The baud-rate for serial terminal display is 115200
Diff: app/ComplianceTest.cpp
- Revision:
- 0:42863a11464a
diff -r 000000000000 -r 42863a11464a app/ComplianceTest.cpp
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/app/ComplianceTest.cpp Fri Aug 26 19:36:35 2016 +0000
@@ -0,0 +1,117 @@
+/*
+ / _____) _ | |
+( (____ _____ ____ _| |_ _____ ____| |__
+ \____ \| ___ | (_ _) ___ |/ ___) _ \
+ _____) ) ____| | | || |_| ____( (___| | | |
+(______/|_____)_|_|_| \__)_____)\____)_| |_|
+ (C)2015 Semtech
+
+Description: Compliance Test for LoRaWAN End-Device
+
+License: Revised BSD License, see LICENSE.TXT file include in the project
+
+Maintainer: Uttam Bhat
+*/
+
+#include "ComplianceTest.h"
+
+
+void PrepareComplianceTestFrame( McpsIndication_t *McpsIndication )
+{
+ uint8_t *pData;
+
+ pData = &McpsIndication->Buffer[0];
+
+ if( ComplianceTest.Running == false )
+ {
+ // Check compliance test enable command (i)
+ if( ( McpsIndication->BufferSize == 4 ) &&
+ ( pData[0] == 0x01 ) && ( pData[1] == 0x01 ) && ( pData[2] == 0x01 ) && (pData[3] == 0x01 ) )
+ {
+ AppPort = 224;
+ AppDataSize = 2;
+ ComplianceTest.DownLinkCounter = 0;
+ ComplianceTest.LinkCheck = false;
+ ComplianceTest.DemodMargin = 0;
+ ComplianceTest.NbGateways = 0;
+ ComplianceTest.Running = true;
+ ComplianceTest.State = 1;
+ }
+ }
+ else
+ {
+ ComplianceTest.State = pData[0];
+ switch( ComplianceTest.State )
+ {
+ case 0: // Check compliance test disable command (ii)
+ IsTxConfirmed = LORAWAN_CONFIRMED_MSG_ON;
+ AppPort = LORAWAN_APP_PORT;
+ AppDataSize = LORAWAN_APP_DATA_SIZE;
+ ComplianceTest.DownLinkCounter = 0;
+ ComplianceTest.Running = false;
+
+ MibRequestConfirm_t mibReq;
+ mibReq.Type = MIB_ADR;
+ mibReq.Param.AdrEnable = LORAWAN_ADR_ON;
+ LoRaMacMibSetRequestConfirm( &mibReq );
+ break;
+ case 1: // (iii, iv)
+ AppDataSize = 2;
+ break;
+ case 2: // Enable confirmed messages (v)
+ IsTxConfirmed = true;
+ ComplianceTest.State = 1;
+ break;
+ case 3: // Disable confirmed messages (vi)
+ IsTxConfirmed = false;
+ ComplianceTest.State = 1;
+ break;
+ case 4: // (vii)
+ AppDataSize = McpsIndication->BufferSize;
+
+ AppData[0] = 4;
+ for( uint8_t i = 1; i < AppDataSize; i++ )
+ {
+ AppData[i] = McpsIndication->Buffer[i] + 1;
+ }
+ break;
+ case 5: // (viii)
+ {
+ MlmeReq_t mlmeReq;
+ mlmeReq.Type = MLME_LINK_CHECK;
+ LoRaMacMlmeRequest( &mlmeReq );
+ }
+ break;
+ default:
+ break;
+ }
+ }
+}
+
+void RunComplianceTest( void )
+{
+ if( ComplianceTest.LinkCheck == true )
+ {
+ ComplianceTest.LinkCheck = false;
+ AppDataSize = 3;
+ AppData[0] = 5;
+ AppData[1] = ComplianceTest.DemodMargin;
+ AppData[2] = ComplianceTest.NbGateways;
+ ComplianceTest.State = 1;
+ }
+ else
+ {
+ switch( ComplianceTest.State )
+ {
+ case 1:
+ AppDataSize = 2;
+ AppData[0] = ComplianceTest.DownLinkCounter >> 8;
+ AppData[1] = ComplianceTest.DownLinkCounter;
+ break;
+
+ case 4:
+ ComplianceTest.State = 1;
+ break;
+ }
+ }
+}
\ No newline at end of file