Uttam Bhat / LoRaWAN-SX1276-Application-Demo

SX1276 Shield based Applications

Dependencies:   X_NUCLEO_IKS01A1 LoRaWAN-lib SX1276Lib mbed

LoRaWAN-SX1276-Application Demo uses SX1276MB1LAS mbed component shield on a nucleo board platform to demonstrate a Class-A LoRaWAN device in the 915MHz ISM band for North American region. It uses the LoRaWAN-lib and SX1276Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_APPLICATION_EUI (8 Bytes)
• LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

Activation by Personalization (ABP) can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_NWKSKEY (16 Bytes)
• LORAWAN_APPSKEY (16 Bytes)

Config.h (LoRaWAN Communication Parameters)

• Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled

• Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled

• Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE

• Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.

• Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4

• Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.

• ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.

• Application Port : The application port can be set using parameter LORAWAN_APP_PORT. A few examples are associated to specific Application Port, and are defined in Config.h

• Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE

• Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

The baud-rate for serial terminal display is 115200

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/app/LoRaDeviceStateProc.h	Fri Aug 26 19:36:35 2016 +0000
@@ -0,0 +1,105 @@
+/*
+ / _____)             _              | |
+( (____  _____ ____ _| |_ _____  ____| |__
+ \____ \| ___ |    (_   _) ___ |/ ___)  _ \
+ _____) ) ____| | | || |_| ____( (___| | | |
+(______/|_____)_|_|_| \__)_____)\____)_| |_|
+    (C)2015 Semtech
+
+Description: Process function calls from various Device states
+
+License: Revised BSD License, see LICENSE.TXT file include in the project
+
+Maintainer: Uttam Bhat
+*/
+#ifndef __LORA_DEVICE_STATE_H__
+#define __LORA_DEVICE_STATE_H__
+
+#include "Common.h"
+#include "board.h"
+#include "LoRaMac.h"
+#include "LoRaEventProc.h"
+#include "SerialDisplay.h"
+#include "mbed.h"
+#include "LoRaMacLayerService.h"
+
+/*!
+ * Strucure containing the Uplink status
+ */
+struct sLoRaMacUplinkStatus
+{
+    /*!
+     * MCPS-Request type
+     */
+    Mcps_t Type;    
+    uint8_t Acked;
+    int8_t Datarate;
+    uint16_t UplinkCounter;
+    uint8_t Port;
+    uint8_t *Buffer;
+    uint8_t BufferSize;
+    int8_t TxPower;
+};
+
+/*!
+ * Strucure containing the Downlink status
+ */
+struct sLoRaMacDownlinkStatus
+{
+    int16_t Rssi;
+    int8_t Snr;
+    uint16_t DownlinkCounter;
+    bool RxData;
+    uint8_t Port;
+    uint8_t *Buffer;
+    uint8_t BufferSize;
+    uint8_t RxSlot;
+};
+
+/*!
+ * Device states
+ */
+enum eDevicState
+{
+    DEVICE_STATE_INIT,
+    DEVICE_STATE_JOIN,
+    DEVICE_STATE_SEND,
+    DEVICE_STATE_SLEEP
+};
+
+extern sLoRaMacUplinkStatus LoRaMacUplinkStatus;
+
+extern sLoRaMacDownlinkStatus LoRaMacDownlinkStatus;
+
+extern eDevicState DeviceState;
+
+/*!
+ * \brief Initialize Device: Timer, MAC Services, MAC
+ */
+void DeviceInit( void );
+
+/*!
+ * \brief Device Join update
+ */
+void DeviceJoinUpdate( void );
+
+/*!
+ * \brief OTA: if device not joined, send JOIN REQUEST to network
+ *      ABP: Request DevAddr if not already set
+ */
+void DeviceJoin( void );
+
+/*!
+ * \brief   Prepares the payload of the frame to be transmitted
+ *
+ * \param [IN] port application port corresponding to which payload is generated
+ */
+void PrepareTxFrame( uint8_t port );
+
+/*!
+ * \brief   Send the frame
+ *
+ */
+bool SendFrame( void );
+
+#endif // __LORA_DEVICE_STATE_H__
\ No newline at end of file