Uttam Bhat / LoRaWAN-SX1276-Application-Demo

SX1276 Shield based Applications

Dependencies:   X_NUCLEO_IKS01A1 LoRaWAN-lib SX1276Lib mbed

LoRaWAN-SX1276-Application Demo uses SX1276MB1LAS mbed component shield on a nucleo board platform to demonstrate a Class-A LoRaWAN device in the 915MHz ISM band for North American region. It uses the LoRaWAN-lib and SX1276Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below. /media/uploads/ubhat/ota_enable.png

The end-device must be configured with the following parameters:

  • LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
  • LORAWAN_APPLICATION_EUI (8 Bytes)
  • LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

/media/uploads/ubhat/ota_eui.png

Activation by Personalization (ABP) can be enabled as shown in the figure below. /media/uploads/ubhat/abp_enable.png

The end-device must be configured with the following parameters:

  • LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
  • LORAWAN_NWKSKEY (16 Bytes)
  • LORAWAN_APPSKEY (16 Bytes)

/media/uploads/ubhat/abp_key.png

Config.h (LoRaWAN Communication Parameters)

  • Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled /media/uploads/ubhat/hybridenable.png
  • Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled
  • Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE
  • Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.
  • Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4
  • Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.
  • ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.
  • Application Port : The application port can be set using parameter LORAWAN_APP_PORT. A few examples are associated to specific Application Port, and are defined in Config.h
  • Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE
  • Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

/media/uploads/ubhat/loraconfig.png

The baud-rate for serial terminal display is 115200

app/ComplianceTest.h@6:c5f2da0de0b0, 2018-07-18 (annotated)

Committer:
ubhat
Date:
Wed Jul 18 22:26:26 2018 +0000
Revision:
6:c5f2da0de0b0
Parent:
0:42863a11464a 
Add Channel Block option in Config.h; Fix board specific DevEUI allocation

Who changed what in which revision?

UserRevisionLine numberNew contents of line
ubhat 0:42863a11464a 1 /*
ubhat 0:42863a11464a 2 / _____) _ | |
ubhat 0:42863a11464a 3 ( (____ _____ ____ _| |_ _____ ____| |__
ubhat 0:42863a11464a 4 \____ \| ___ | (_ _) ___ |/ ___) _ \
ubhat 0:42863a11464a 5 _____) ) ____| | | || |_| ____( (___| | | |
ubhat 0:42863a11464a 6 (______/|_____)_|_|_| \__)_____)\____)_| |_|
ubhat 0:42863a11464a 7 (C)2015 Semtech
ubhat 0:42863a11464a 8
ubhat 0:42863a11464a 9 Description: Definition of parameters for Compliance Test
ubhat 0:42863a11464a 10
ubhat 0:42863a11464a 11 License: Revised BSD License, see LICENSE.TXT file include in the project
ubhat 0:42863a11464a 12
ubhat 0:42863a11464a 13 Maintainer: Miguel Luis and Gregory Cristian
ubhat 0:42863a11464a 14 */
ubhat 0:42863a11464a 15 #ifndef __COMPLIANCE_H__
ubhat 0:42863a11464a 16 #define __COMPLIANCE_H__
ubhat 0:42863a11464a 17
ubhat 0:42863a11464a 18 #include "mbed.h"
ubhat 0:42863a11464a 19 #include "Common.h"
ubhat 0:42863a11464a 20 #include "Config.h"
ubhat 0:42863a11464a 21 #include "LoRaMac.h"
ubhat 0:42863a11464a 22
ubhat 0:42863a11464a 23 #define COMPLIANCE_TX_DUTYCYCLE 5000000 // 5sec
ubhat 0:42863a11464a 24
ubhat 0:42863a11464a 25 struct ComplianceTest_s
ubhat 0:42863a11464a 26 {
ubhat 0:42863a11464a 27 bool Running;
ubhat 0:42863a11464a 28 uint8_t State;
ubhat 0:42863a11464a 29 bool IsTxConfirmed;
ubhat 0:42863a11464a 30 uint8_t AppPort;
ubhat 0:42863a11464a 31 uint8_t AppDataSize;
ubhat 0:42863a11464a 32 uint8_t *AppDataBuffer;
ubhat 0:42863a11464a 33 uint16_t DownLinkCounter;
ubhat 0:42863a11464a 34 bool LinkCheck;
ubhat 0:42863a11464a 35 uint8_t DemodMargin;
ubhat 0:42863a11464a 36 uint8_t NbGateways;
ubhat 0:42863a11464a 37 };
ubhat 0:42863a11464a 38
ubhat 0:42863a11464a 39 extern ComplianceTest_s ComplianceTest;
ubhat 0:42863a11464a 40
ubhat 0:42863a11464a 41 void PrepareComplianceTestFrame( McpsIndication_t *McpsIndication );
ubhat 0:42863a11464a 42 void RunComplianceTest( void );
ubhat 0:42863a11464a 43
ubhat 0:42863a11464a 44 #endif // __COMPLIANCE_H__