mbed library sources
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_rtc.c
- Revision:
- 76:aeb1df146756
- Child:
- 80:66393a7b209d
diff -r 99bf659e4489 -r aeb1df146756 targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_rtc.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_rtc.c Mon Jan 27 14:30:07 2014 +0000 @@ -0,0 +1,2675 @@ +/** + ****************************************************************************** + * @file stm32l1xx_rtc.c + * @author MCD Application Team + * @version V1.2.0 + * @date 22-February-2013 + * @brief This file provides firmware functions to manage the following + * functionalities of the Real-Time Clock (RTC) peripheral: + * + Initialization + * + Calendar (Time and Date) configuration + * + Alarms (Alarm A and Alarm B) configuration + * + WakeUp Timer configuration + * + Daylight Saving configuration + * + Output pin Configuration + * + Coarse digital Calibration configuration + * + Smooth digital Calibration configuration + * + TimeStamp configuration + * + Tampers configuration + * + Backup Data Registers configuration + * + Output Type Config configuration + * + Shift control synchronisation + * + Interrupts and flags management + * + @verbatim + + =============================================================================== + ##### RTC Domain Reset ##### + =============================================================================== + [..] After power-on reset, the RTC domain (RTC clock source configuration, + RTC registers and RTC Backup data registers) is reset. You can also + reset this domain by software using the RCC_RTCResetCmd() function. + + ##### RTC Operating Condition ##### + =============================================================================== + [..] As long as the supply voltage remains in the operating range, + the RTC never stops, regardless of the device status (Run mode, + low power modes or under reset). + + ##### RTC Domain Access ##### + =============================================================================== + [..] After reset, the RTC domain (RTC clock source configuration, + RTC registers and RTC Backup data registers) are protected against + possible stray write accesses. + [..] To enable access to the RTC Domain and RTC registers, proceed as follows: + (+) Enable the Power Controller (PWR) APB1 interface clock using the + RCC_APB1PeriphClockCmd() function. + (+) Enable access to RTC domain using the PWR_RTCAccessCmd() function. + (+) Select the RTC clock source using the RCC_RTCCLKConfig() function. + (+) Enable RTC Clock using the RCC_RTCCLKCmd() function. + + ##### How to use this driver ##### + =============================================================================== + [..] + (+) Enable the RTC domain access (see description in the section above) + (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and + RTC hour format using the RTC_Init() function. + ***Time and Date configuration *** + ================================== + [..] + (+) To configure the RTC Calendar (Time and Date) use the RTC_SetTime() + and RTC_SetDate() functions. + (+) To read the RTC Calendar, use the RTC_GetTime() and RTC_GetDate() + functions. + (+) To read the RTC subsecond, use the RTC_GetSubSecond() function. + (+) Use the RTC_DayLightSavingConfig() function to add or sub one + hour to the RTC Calendar. + + ***Alarm configuration *** + ========================== + [..] + (+) To configure the RTC Alarm use the RTC_SetAlarm() function. + (+) Enable the selected RTC Alarm using the RTC_AlarmCmd() function + (+) To read the RTC Alarm, use the RTC_GetAlarm() function. + (+) To read the RTC alarm SubSecond, use the RTC_GetAlarmSubSecond() function. + + ***RTC Wakeup configuration *** + =============================== + [..] + (+) Configure the RTC Wakeup Clock source use the RTC_WakeUpClockConfig() + function. + (+) Configure the RTC WakeUp Counter using the RTC_SetWakeUpCounter() + function. + (+) Enable the RTC WakeUp using the RTC_WakeUpCmd() function + (+) To read the RTC WakeUp Counter register, use the RTC_GetWakeUpCounter() + function. + + ***Outputs configuration *** + ============================ + [..] The RTC has 2 different outputs: + (+) AFO_ALARM: this output is used to manage the RTC Alarm A, Alarm B + and WaKeUp signals. + To output the selected RTC signal on RTC_AF1 pin, use the + RTC_OutputConfig() function. + (+) AFO_CALIB: this output is 512Hz signal or 1Hz. + To output the RTC Clock on RTC_AF1 pin, use the RTC_CalibOutputCmd() + function. + + ***Smooth digital Calibration configuration *** + =============================================== + [..] + (+) Configure the RTC Original Digital Calibration Value and the corresponding + calibration cycle period (32s,16s and 8s) using the RTC_SmoothCalibConfig() + function. + + ***Coarse digital Calibration configuration *** + =============================================== + [..] + (+) Configure the RTC Coarse Calibration Value and the corresponding + sign using the RTC_CoarseCalibConfig() function. + (+) Enable the RTC Coarse Calibration using the RTC_CoarseCalibCmd() + function. + + ***TimeStamp configuration *** + ============================== + [..] + (+) Configure the RTC_AF1 trigger and enables the RTC TimeStamp + using the RTC_TimeStampCmd() function. + (+) To read the RTC TimeStamp Time and Date register, use the + RTC_GetTimeStamp() function. + (+) To read the RTC TimeStamp SubSecond register, use the + RTC_GetTimeStampSubSecond() function. + + ***Tamper configuration *** + =========================== + [..] + (+) Configure the Tamper filter count using RTC_TamperFilterConfig() + function. + (+) Configure the RTC Tamper trigger Edge or Level according to the Tamper + filter (if equal to 0 Edge else Level) value using the RTC_TamperConfig() + function. + (+) Configure the Tamper sampling frequency using RTC_TamperSamplingFreqConfig() + function. + (+) Configure the Tamper precharge or discharge duration using + RTC_TamperPinsPrechargeDuration() function. + (+) Enable the Tamper Pull-UP using RTC_TamperPullUpDisableCmd() function. + (+) Enable the RTC Tamper using the RTC_TamperCmd() function. + (+) Enable the Time stamp on Tamper detection event using + RTC_TSOnTamperDetecCmd() function. + + ***Backup Data Registers configuration *** + ========================================== + [..] + (+) To write to the RTC Backup Data registers, use the RTC_WriteBackupRegister() + function. + (+) To read the RTC Backup Data registers, use the RTC_ReadBackupRegister() + function. + + ##### RTC and low power modes ##### + =============================================================================== + [..] The MCU can be woken up from a low power mode by an RTC alternate + function. + [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B), + RTC wakeup, RTC tamper event detection and RTC time stamp event detection. + These RTC alternate functions can wake up the system from the Stop + and Standby lowpower modes. + The system can also wake up from low power modes without depending + on an external interrupt (Auto-wakeup mode), by using the RTC alarm + or the RTC wakeup events. + [..] The RTC provides a programmable time base for waking up from the + Stop or Standby mode at regular intervals. + Wakeup from STOP and Standby modes is possible only when the RTC + clock source is LSE or LSI. + + ##### Selection of RTC_AF1 alternate functions ##### + =============================================================================== + [..] The RTC_AF1 pin (PC13) can be used for the following purposes: + (+) Wakeup pin 2 (WKUP2) using the PWR_WakeUpPinCmd() function. + (+) AFO_ALARM output. + (+) AFO_CALIB output. + (+) AFI_TAMPER. + (+) AFI_TIMESTAMP. + + +------------------------------------------------------------------------------------------+ + | Pin |AFO_ALARM |AFO_CALIB |AFI_TAMPER |AFI_TIMESTAMP | WKUP2 |ALARMOUTTYPE | + | configuration | ENABLED | ENABLED | ENABLED | ENABLED |ENABLED | AFO_ALARM | + | and function | | | | | |Configuration | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | Alarm out | | | | | Don't | | + | output OD | 1 | 0 |Don't care | Don't care | care | 0 | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | Alarm out | | | | | Don't | | + | output PP | 1 | 0 |Don't care | Don't care | care | 1 | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | Calibration out | | | | | Don't | | + | output PP | 0 | 1 |Don't care | Don't care | care | Don't care | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | TAMPER input | | | | | Don't | | + | floating | 0 | 0 | 1 | 0 | care | Don't care | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | TIMESTAMP and | | | | | Don't | | + | TAMPER input | 0 | 0 | 1 | 1 | care | Don't care | + | floating | | | | | | | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | TIMESTAMP input | | | | | Don't | | + | floating | 0 | 0 | 0 | 1 | care | Don't care | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | Wakeup Pin 2 | 0 | 0 | 0 | 0 | 1 | Don't care | + |-----------------|----------|----------|-----------|--------------|--------|--------------| + | Standard GPIO | 0 | 0 | 0 | 0 | 0 | Don't care | + +------------------------------------------------------------------------------------------+ + + @endverbatim + + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l1xx_rtc.h" +#include "stm32l1xx_rcc.h" + +/** @addtogroup STM32L1xx_StdPeriph_Driver + * @{ + */ + +/** @defgroup RTC + * @brief RTC driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ + +/* Masks Definition */ +#define RTC_TR_RESERVED_MASK ((uint32_t)0x007F7F7F) +#define RTC_DR_RESERVED_MASK ((uint32_t)0x00FFFF3F) +#define RTC_INIT_MASK ((uint32_t)0xFFFFFFFF) +#define RTC_RSF_MASK ((uint32_t)0xFFFFFF5F) +#define RTC_FLAGS_MASK ((uint32_t)(RTC_FLAG_TSOVF | RTC_FLAG_TSF | RTC_FLAG_WUTF | \ + RTC_FLAG_ALRBF | RTC_FLAG_ALRAF | RTC_FLAG_INITF | \ + RTC_FLAG_RSF | RTC_FLAG_INITS | RTC_FLAG_WUTWF | \ + RTC_FLAG_ALRBWF | RTC_FLAG_ALRAWF | RTC_FLAG_TAMP1F | \ + RTC_FLAG_TAMP2F | RTC_FLAG_TAMP3F | RTC_FLAG_RECALPF | \ + RTC_FLAG_SHPF)) + +#define INITMODE_TIMEOUT ((uint32_t) 0x00002000) +#define SYNCHRO_TIMEOUT ((uint32_t) 0x00008000) +#define RECALPF_TIMEOUT ((uint32_t) 0x00001000) +#define SHPF_TIMEOUT ((uint32_t) 0x00002000) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +static uint8_t RTC_ByteToBcd2(uint8_t Value); +static uint8_t RTC_Bcd2ToByte(uint8_t Value); + +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup RTC_Private_Functions + * @{ + */ + +/** @defgroup RTC_Group1 Initialization and Configuration functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] This section provide functions allowing to initialize and configure the + RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable + RTC registers Write protection, enter and exit the RTC initialization mode, + RTC registers synchronization check and reference clock detection enable. + (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base. + It is split into 2 programmable prescalers to minimize power consumption. + (++) A 7-bit asynchronous prescaler and A 13-bit synchronous prescaler. + (++) When both prescalers are used, it is recommended to configure the + asynchronous prescaler to a high value to minimize consumption. + (#) All RTC registers are Write protected. Writing to the RTC registers + is enabled by writing a key into the Write Protection register, RTC_WPR. + (#) To Configure the RTC Calendar, user application should enter + initialization mode. In this mode, the calendar counter is stopped + and its value can be updated. When the initialization sequence is + complete, the calendar restarts counting after 4 RTCCLK cycles. + (#) To read the calendar through the shadow registers after Calendar + initialization, calendar update or after wakeup from low power modes + the software must first clear the RSF flag. The software must then + wait until it is set again before reading the calendar, which means + that the calendar registers have been correctly copied into the + RTC_TR and RTC_DR shadow registers.The RTC_WaitForSynchro() function + implements the above software sequence (RSF clear and RSF check). + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the RTC registers to their default reset values. + * @note This function doesn't reset the RTC Clock source and RTC Backup Data + * registers. + * @param None + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC registers are deinitialized + * - ERROR: RTC registers are not deinitialized + */ +ErrorStatus RTC_DeInit(void) +{ + __IO uint32_t wutcounter = 0x00; + uint32_t wutwfstatus = 0x00; + ErrorStatus status = ERROR; + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + /* Reset TR, DR and CR registers */ + RTC->TR = (uint32_t)0x00000000; + RTC->DR = (uint32_t)0x00002101; + + /* Reset All CR bits except CR[2:0] */ + RTC->CR &= (uint32_t)0x00000007; + + /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ + do + { + wutwfstatus = RTC->ISR & RTC_ISR_WUTWF; + wutcounter++; + } while((wutcounter != INITMODE_TIMEOUT) && (wutwfstatus == 0x00)); + + if ((RTC->ISR & RTC_ISR_WUTWF) == RESET) + { + status = ERROR; + } + else + { + /* Reset all RTC CR register bits */ + RTC->CR &= (uint32_t)0x00000000; + RTC->WUTR = (uint32_t)0x0000FFFF; + RTC->PRER = (uint32_t)0x007F00FF; + RTC->CALIBR = (uint32_t)0x00000000; + RTC->ALRMAR = (uint32_t)0x00000000; + RTC->ALRMBR = (uint32_t)0x00000000; + RTC->SHIFTR = (uint32_t)0x00000000; + RTC->CALR = (uint32_t)0x00000000; + RTC->ALRMASSR = (uint32_t)0x00000000; + RTC->ALRMBSSR = (uint32_t)0x00000000; + + /* Reset ISR register and exit initialization mode */ + RTC->ISR = (uint32_t)0x00000000; + + /* Reset Tamper and alternate functions configuration register */ + RTC->TAFCR = 0x00000000; + + /* Wait till the RTC RSF flag is set */ + if (RTC_WaitForSynchro() == ERROR) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Initializes the RTC registers according to the specified parameters + * in RTC_InitStruct. + * @param RTC_InitStruct: pointer to a RTC_InitTypeDef structure that contains + * the configuration information for the RTC peripheral. + * @note The RTC Prescaler register is write protected and can be written in + * initialization mode only. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC registers are initialized + * - ERROR: RTC registers are not initialized + */ +ErrorStatus RTC_Init(RTC_InitTypeDef* RTC_InitStruct) +{ + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_RTC_HOUR_FORMAT(RTC_InitStruct->RTC_HourFormat)); + assert_param(IS_RTC_ASYNCH_PREDIV(RTC_InitStruct->RTC_AsynchPrediv)); + assert_param(IS_RTC_SYNCH_PREDIV(RTC_InitStruct->RTC_SynchPrediv)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + /* Clear RTC CR FMT Bit */ + RTC->CR &= ((uint32_t)~(RTC_CR_FMT)); + /* Set RTC_CR register */ + RTC->CR |= ((uint32_t)(RTC_InitStruct->RTC_HourFormat)); + + /* Configure the RTC PRER */ + RTC->PRER = (uint32_t)(RTC_InitStruct->RTC_SynchPrediv); + RTC->PRER |= (uint32_t)(RTC_InitStruct->RTC_AsynchPrediv << 16); + + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + status = SUCCESS; + } + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Fills each RTC_InitStruct member with its default value. + * @param RTC_InitStruct: pointer to a RTC_InitTypeDef structure which will be + * initialized. + * @retval None + */ +void RTC_StructInit(RTC_InitTypeDef* RTC_InitStruct) +{ + /* Initialize the RTC_HourFormat member */ + RTC_InitStruct->RTC_HourFormat = RTC_HourFormat_24; + + /* Initialize the RTC_AsynchPrediv member */ + RTC_InitStruct->RTC_AsynchPrediv = (uint32_t)0x7F; + + /* Initialize the RTC_SynchPrediv member */ + RTC_InitStruct->RTC_SynchPrediv = (uint32_t)0xFF; +} + +/** + * @brief Enables or disables the RTC registers write protection. + * @note All the RTC registers are write protected except for RTC_ISR[13:8], + * RTC_TAFCR and RTC_BKPxR. + * @note Writing a wrong key reactivates the write protection. + * @note The protection mechanism is not affected by system reset. + * @param NewState: new state of the write protection. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_WriteProtectionCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + } + else + { + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + } +} + +/** + * @brief Enters the RTC Initialization mode. + * @note The RTC Initialization mode is write protected, use the + * RTC_WriteProtectionCmd(DISABLE) before calling this function. + * @param None + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC is in Init mode + * - ERROR: RTC is not in Init mode + */ +ErrorStatus RTC_EnterInitMode(void) +{ + __IO uint32_t initcounter = 0x00; + ErrorStatus status = ERROR; + uint32_t initstatus = 0x00; + + /* Check if the Initialization mode is set */ + if ((RTC->ISR & RTC_ISR_INITF) == (uint32_t)RESET) + { + /* Set the Initialization mode */ + RTC->ISR = (uint32_t)RTC_INIT_MASK; + + /* Wait till RTC is in INIT state and if Time out is reached exit */ + do + { + initstatus = RTC->ISR & RTC_ISR_INITF; + initcounter++; + } while((initcounter != INITMODE_TIMEOUT) && (initstatus == 0x00)); + + if ((RTC->ISR & RTC_ISR_INITF) != RESET) + { + status = SUCCESS; + } + else + { + status = ERROR; + } + } + else + { + status = SUCCESS; + } + + return (status); +} + +/** + * @brief Exits the RTC Initialization mode. + * @note When the initialization sequence is complete, the calendar restarts + * counting after 4 RTCCLK cycles. + * @note The RTC Initialization mode is write protected, use the + * RTC_WriteProtectionCmd(DISABLE) before calling this function. + * @param None + * @retval None + */ +void RTC_ExitInitMode(void) +{ + /* Exit Initialization mode */ + RTC->ISR &= (uint32_t)~RTC_ISR_INIT; +} + +/** + * @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are + * synchronized with RTC APB clock. + * @note The RTC Resynchronization mode is write protected, use the + * RTC_WriteProtectionCmd(DISABLE) before calling this function. + * @note To read the calendar through the shadow registers after Calendar + * initialization, calendar update or after wakeup from low power modes + * the software must first clear the RSF flag. + * The software must then wait until it is set again before reading + * the calendar, which means that the calendar registers have been + * correctly copied into the RTC_TR and RTC_DR shadow registers. + * @param None + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC registers are synchronised + * - ERROR: RTC registers are not synchronised + */ +ErrorStatus RTC_WaitForSynchro(void) +{ + __IO uint32_t synchrocounter = 0; + ErrorStatus status = ERROR; + uint32_t synchrostatus = 0x00; + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Clear RSF flag */ + RTC->ISR &= (uint32_t)RTC_RSF_MASK; + + /* Wait the registers to be synchronised */ + do + { + synchrostatus = RTC->ISR & RTC_ISR_RSF; + synchrocounter++; + } while((synchrocounter != SYNCHRO_TIMEOUT) && (synchrostatus == 0x00)); + + if ((RTC->ISR & RTC_ISR_RSF) != RESET) + { + status = SUCCESS; + } + else + { + status = ERROR; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return (status); +} + +/** + * @brief Enables or disables the RTC reference clock detection. + * @param NewState: new state of the RTC reference clock. + * This parameter can be: ENABLE or DISABLE. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC reference clock detection is enabled + * - ERROR: RTC reference clock detection is disabled + */ +ErrorStatus RTC_RefClockCmd(FunctionalState NewState) +{ + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + if (NewState != DISABLE) + { + /* Enable the RTC reference clock detection */ + RTC->CR |= RTC_CR_REFCKON; + } + else + { + /* Disable the RTC reference clock detection */ + RTC->CR &= ~RTC_CR_REFCKON; + } + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + status = SUCCESS; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Enables or Disables the Bypass Shadow feature. + * @note When the Bypass Shadow is enabled the calendar value are taken + * directly from the Calendar counter. + * @param NewState: new state of the Bypass Shadow feature. + * This parameter can be: ENABLE or DISABLE. + * @retval None +*/ +void RTC_BypassShadowCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + if (NewState != DISABLE) + { + /* Set the BYPSHAD bit */ + RTC->CR |= (uint8_t)RTC_CR_BYPSHAD; + } + else + { + /* Reset the BYPSHAD bit */ + RTC->CR &= (uint8_t)~RTC_CR_BYPSHAD; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @} + */ + +/** @defgroup RTC_Group2 Time and Date configuration functions + * @brief Time and Date configuration functions + * +@verbatim + =============================================================================== + ##### Time and Date configuration functions ##### + =============================================================================== + [..] This section provide functions allowing to program and read the RTC + Calendar (Time and Date). + +@endverbatim + * @{ + */ + +/** + * @brief Set the RTC current time. + * @param RTC_Format: specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_TimeStruct: pointer to a RTC_TimeTypeDef structure that contains + * the time configuration information for the RTC. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Time register is configured + * - ERROR: RTC Time register is not configured + */ +ErrorStatus RTC_SetTime(uint32_t RTC_Format, RTC_TimeTypeDef* RTC_TimeStruct) +{ + uint32_t tmpreg = 0; + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + + if (RTC_Format == RTC_Format_BIN) + { + if ((RTC->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + assert_param(IS_RTC_HOUR12(RTC_TimeStruct->RTC_Hours)); + assert_param(IS_RTC_H12(RTC_TimeStruct->RTC_H12)); + } + else + { + RTC_TimeStruct->RTC_H12 = 0x00; + assert_param(IS_RTC_HOUR24(RTC_TimeStruct->RTC_Hours)); + } + assert_param(IS_RTC_MINUTES(RTC_TimeStruct->RTC_Minutes)); + assert_param(IS_RTC_SECONDS(RTC_TimeStruct->RTC_Seconds)); + } + else + { + if ((RTC->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + tmpreg = RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Hours); + assert_param(IS_RTC_HOUR12(tmpreg)); + assert_param(IS_RTC_H12(RTC_TimeStruct->RTC_H12)); + } + else + { + RTC_TimeStruct->RTC_H12 = 0x00; + assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Hours))); + } + assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Minutes))); + assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Seconds))); + } + + /* Check the input parameters format */ + if (RTC_Format != RTC_Format_BIN) + { + tmpreg = (((uint32_t)(RTC_TimeStruct->RTC_Hours) << 16) | \ + ((uint32_t)(RTC_TimeStruct->RTC_Minutes) << 8) | \ + ((uint32_t)RTC_TimeStruct->RTC_Seconds) | \ + ((uint32_t)(RTC_TimeStruct->RTC_H12) << 16)); + } + else + { + tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(RTC_TimeStruct->RTC_Hours) << 16) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_TimeStruct->RTC_Minutes) << 8) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_TimeStruct->RTC_Seconds)) | \ + (((uint32_t)RTC_TimeStruct->RTC_H12) << 16)); + } + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + /* Set the RTC_TR register */ + RTC->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK); + + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if ((RTC->CR & RTC_CR_BYPSHAD) == RESET) + { + if (RTC_WaitForSynchro() == ERROR) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + else + { + status = SUCCESS; + } + + } + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Fills each RTC_TimeStruct member with its default value + * (Time = 00h:00min:00sec). + * @param RTC_TimeStruct: pointer to a RTC_TimeTypeDef structure which will be + * initialized. + * @retval None + */ +void RTC_TimeStructInit(RTC_TimeTypeDef* RTC_TimeStruct) +{ + /* Time = 00h:00min:00sec */ + RTC_TimeStruct->RTC_H12 = RTC_H12_AM; + RTC_TimeStruct->RTC_Hours = 0; + RTC_TimeStruct->RTC_Minutes = 0; + RTC_TimeStruct->RTC_Seconds = 0; +} + +/** + * @brief Get the RTC current Time. + * @param RTC_Format: specifies the format of the returned parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_TimeStruct: pointer to a RTC_TimeTypeDef structure that will + * contain the returned current time configuration. + * @retval None + */ +void RTC_GetTime(uint32_t RTC_Format, RTC_TimeTypeDef* RTC_TimeStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + + /* Get the RTC_TR register */ + tmpreg = (uint32_t)(RTC->TR & RTC_TR_RESERVED_MASK); + + /* Fill the structure fields with the read parameters */ + RTC_TimeStruct->RTC_Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16); + RTC_TimeStruct->RTC_Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >>8); + RTC_TimeStruct->RTC_Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU)); + RTC_TimeStruct->RTC_H12 = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16); + + /* Check the input parameters format */ + if (RTC_Format == RTC_Format_BIN) + { + /* Convert the structure parameters to Binary format */ + RTC_TimeStruct->RTC_Hours = (uint8_t)RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Hours); + RTC_TimeStruct->RTC_Minutes = (uint8_t)RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Minutes); + RTC_TimeStruct->RTC_Seconds = (uint8_t)RTC_Bcd2ToByte(RTC_TimeStruct->RTC_Seconds); + } +} + +/** + * @brief Gets the RTC current Calendar Subseconds value. + * @note This function freeze the Time and Date registers after reading the + * SSR register. + * @param None + * @retval RTC current Calendar Subseconds value. + */ +uint32_t RTC_GetSubSecond(void) +{ + uint32_t tmpreg = 0; + + /* Get subseconds values from the correspondent registers*/ + tmpreg = (uint32_t)(RTC->SSR); + + /* Read DR register to unfroze calendar registers */ + (void) (RTC->DR); + + return (tmpreg); +} + +/** + * @brief Set the RTC current date. + * @param RTC_Format: specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_DateStruct: pointer to a RTC_DateTypeDef structure that contains + * the date configuration information for the RTC. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Date register is configured + * - ERROR: RTC Date register is not configured + */ +ErrorStatus RTC_SetDate(uint32_t RTC_Format, RTC_DateTypeDef* RTC_DateStruct) +{ + uint32_t tmpreg = 0; + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + + if ((RTC_Format == RTC_Format_BIN) && ((RTC_DateStruct->RTC_Month & 0x10) == 0x10)) + { + RTC_DateStruct->RTC_Month = (RTC_DateStruct->RTC_Month & (uint32_t)~(0x10)) + 0x0A; + } + if (RTC_Format == RTC_Format_BIN) + { + assert_param(IS_RTC_YEAR(RTC_DateStruct->RTC_Year)); + assert_param(IS_RTC_MONTH(RTC_DateStruct->RTC_Month)); + assert_param(IS_RTC_DATE(RTC_DateStruct->RTC_Date)); + } + else + { + assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(RTC_DateStruct->RTC_Year))); + tmpreg = RTC_Bcd2ToByte(RTC_DateStruct->RTC_Month); + assert_param(IS_RTC_MONTH(tmpreg)); + tmpreg = RTC_Bcd2ToByte(RTC_DateStruct->RTC_Date); + assert_param(IS_RTC_DATE(tmpreg)); + } + assert_param(IS_RTC_WEEKDAY(RTC_DateStruct->RTC_WeekDay)); + + /* Check the input parameters format */ + if (RTC_Format != RTC_Format_BIN) + { + tmpreg = ((((uint32_t)RTC_DateStruct->RTC_Year) << 16) | \ + (((uint32_t)RTC_DateStruct->RTC_Month) << 8) | \ + ((uint32_t)RTC_DateStruct->RTC_Date) | \ + (((uint32_t)RTC_DateStruct->RTC_WeekDay) << 13)); + } + else + { + tmpreg = (((uint32_t)RTC_ByteToBcd2(RTC_DateStruct->RTC_Year) << 16) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_DateStruct->RTC_Month) << 8) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_DateStruct->RTC_Date)) | \ + ((uint32_t)RTC_DateStruct->RTC_WeekDay << 13)); + } + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + /* Set the RTC_DR register */ + RTC->DR = (uint32_t)(tmpreg & RTC_DR_RESERVED_MASK); + + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if ((RTC->CR & RTC_CR_BYPSHAD) == RESET) + { + if (RTC_WaitForSynchro() == ERROR) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + else + { + status = SUCCESS; + } + } + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Fills each RTC_DateStruct member with its default value + * (Monday, January 01 xx00). + * @param RTC_DateStruct: pointer to a RTC_DateTypeDef structure which will be + * initialized. + * @retval None + */ +void RTC_DateStructInit(RTC_DateTypeDef* RTC_DateStruct) +{ + /* Monday, January 01 xx00 */ + RTC_DateStruct->RTC_WeekDay = RTC_Weekday_Monday; + RTC_DateStruct->RTC_Date = 1; + RTC_DateStruct->RTC_Month = RTC_Month_January; + RTC_DateStruct->RTC_Year = 0; +} + +/** + * @brief Get the RTC current date. + * @param RTC_Format: specifies the format of the returned parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_DateStruct: pointer to a RTC_DateTypeDef structure that will + * contain the returned current date configuration. + * @retval None + */ +void RTC_GetDate(uint32_t RTC_Format, RTC_DateTypeDef* RTC_DateStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + + /* Get the RTC_TR register */ + tmpreg = (uint32_t)(RTC->DR & RTC_DR_RESERVED_MASK); + + /* Fill the structure fields with the read parameters */ + RTC_DateStruct->RTC_Year = (uint8_t)((tmpreg & (RTC_DR_YT | RTC_DR_YU)) >> 16); + RTC_DateStruct->RTC_Month = (uint8_t)((tmpreg & (RTC_DR_MT | RTC_DR_MU)) >> 8); + RTC_DateStruct->RTC_Date = (uint8_t)(tmpreg & (RTC_DR_DT | RTC_DR_DU)); + RTC_DateStruct->RTC_WeekDay = (uint8_t)((tmpreg & (RTC_DR_WDU)) >> 13); + + /* Check the input parameters format */ + if (RTC_Format == RTC_Format_BIN) + { + /* Convert the structure parameters to Binary format */ + RTC_DateStruct->RTC_Year = (uint8_t)RTC_Bcd2ToByte(RTC_DateStruct->RTC_Year); + RTC_DateStruct->RTC_Month = (uint8_t)RTC_Bcd2ToByte(RTC_DateStruct->RTC_Month); + RTC_DateStruct->RTC_Date = (uint8_t)RTC_Bcd2ToByte(RTC_DateStruct->RTC_Date); + } +} + +/** + * @} + */ + +/** @defgroup RTC_Group3 Alarms configuration functions + * @brief Alarms (Alarm A and Alarm B) configuration functions + * +@verbatim + =============================================================================== + ##### Alarms (Alarm A and Alarm B) configuration functions ##### + =============================================================================== + [..] This section provide functions allowing to program and read the RTC + Alarms. + +@endverbatim + * @{ + */ + +/** + * @brief Set the specified RTC Alarm. + * @note The Alarm register can only be written when the corresponding Alarm + * is disabled (Use the RTC_AlarmCmd(DISABLE)). + * @param RTC_Format: specifies the format of the returned parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_Alarm: specifies the alarm to be configured. + * This parameter can be one of the following values: + * @arg RTC_Alarm_A: to select Alarm A. + * @arg RTC_Alarm_B: to select Alarm B. + * @param RTC_AlarmStruct: pointer to a RTC_AlarmTypeDef structure that + * contains the alarm configuration parameters. + * @retval None + */ +void RTC_SetAlarm(uint32_t RTC_Format, uint32_t RTC_Alarm, RTC_AlarmTypeDef* RTC_AlarmStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + assert_param(IS_RTC_ALARM(RTC_Alarm)); + assert_param(IS_ALARM_MASK(RTC_AlarmStruct->RTC_AlarmMask)); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(RTC_AlarmStruct->RTC_AlarmDateWeekDaySel)); + + if (RTC_Format == RTC_Format_BIN) + { + if ((RTC->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + assert_param(IS_RTC_HOUR12(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours)); + assert_param(IS_RTC_H12(RTC_AlarmStruct->RTC_AlarmTime.RTC_H12)); + } + else + { + RTC_AlarmStruct->RTC_AlarmTime.RTC_H12 = 0x00; + assert_param(IS_RTC_HOUR24(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours)); + } + assert_param(IS_RTC_MINUTES(RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes)); + assert_param(IS_RTC_SECONDS(RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds)); + + if(RTC_AlarmStruct->RTC_AlarmDateWeekDaySel == RTC_AlarmDateWeekDaySel_Date) + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_AlarmStruct->RTC_AlarmDateWeekDay)); + } + else + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_AlarmStruct->RTC_AlarmDateWeekDay)); + } + } + else + { + if ((RTC->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + tmpreg = RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours); + assert_param(IS_RTC_HOUR12(tmpreg)); + assert_param(IS_RTC_H12(RTC_AlarmStruct->RTC_AlarmTime.RTC_H12)); + } + else + { + RTC_AlarmStruct->RTC_AlarmTime.RTC_H12 = 0x00; + assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours))); + } + + assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes))); + assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds))); + + if(RTC_AlarmStruct->RTC_AlarmDateWeekDaySel == RTC_AlarmDateWeekDaySel_Date) + { + tmpreg = RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg)); + } + else + { + tmpreg = RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg)); + } + } + + /* Check the input parameters format */ + if (RTC_Format != RTC_Format_BIN) + { + tmpreg = (((uint32_t)(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours) << 16) | \ + ((uint32_t)(RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes) << 8) | \ + ((uint32_t)RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds) | \ + ((uint32_t)(RTC_AlarmStruct->RTC_AlarmTime.RTC_H12) << 16) | \ + ((uint32_t)(RTC_AlarmStruct->RTC_AlarmDateWeekDay) << 24) | \ + ((uint32_t)RTC_AlarmStruct->RTC_AlarmDateWeekDaySel) | \ + ((uint32_t)RTC_AlarmStruct->RTC_AlarmMask)); + } + else + { + tmpreg = (((uint32_t)RTC_ByteToBcd2(RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours) << 16) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes) << 8) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds)) | \ + ((uint32_t)(RTC_AlarmStruct->RTC_AlarmTime.RTC_H12) << 16) | \ + ((uint32_t)RTC_ByteToBcd2(RTC_AlarmStruct->RTC_AlarmDateWeekDay) << 24) | \ + ((uint32_t)RTC_AlarmStruct->RTC_AlarmDateWeekDaySel) | \ + ((uint32_t)RTC_AlarmStruct->RTC_AlarmMask)); + } + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Configure the Alarm register */ + if (RTC_Alarm == RTC_Alarm_A) + { + RTC->ALRMAR = (uint32_t)tmpreg; + } + else + { + RTC->ALRMBR = (uint32_t)tmpreg; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Fills each RTC_AlarmStruct member with its default value + * (Time = 00h:00mn:00sec / Date = 1st day of the month/Mask = + * all fields are masked). + * @param RTC_AlarmStruct: pointer to a @ref RTC_AlarmTypeDef structure which + * will be initialized. + * @retval None + */ +void RTC_AlarmStructInit(RTC_AlarmTypeDef* RTC_AlarmStruct) +{ + /* Alarm Time Settings : Time = 00h:00mn:00sec */ + RTC_AlarmStruct->RTC_AlarmTime.RTC_H12 = RTC_H12_AM; + RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours = 0; + RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes = 0; + RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds = 0; + + /* Alarm Date Settings : Date = 1st day of the month */ + RTC_AlarmStruct->RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date; + RTC_AlarmStruct->RTC_AlarmDateWeekDay = 1; + + /* Alarm Masks Settings : Mask = all fields are not masked */ + RTC_AlarmStruct->RTC_AlarmMask = RTC_AlarmMask_None; +} + +/** + * @brief Get the RTC Alarm value and masks. + * @param RTC_Format: specifies the format of the output parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format. + * @arg RTC_Format_BCD: BCD data format. + * @param RTC_Alarm: specifies the alarm to be read. + * This parameter can be one of the following values: + * @arg RTC_Alarm_A: to select Alarm A. + * @arg RTC_Alarm_B: to select Alarm B. + * @param RTC_AlarmStruct: pointer to a RTC_AlarmTypeDef structure that will + * contains the output alarm configuration values. + * @retval None + */ +void RTC_GetAlarm(uint32_t RTC_Format, uint32_t RTC_Alarm, RTC_AlarmTypeDef* RTC_AlarmStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + assert_param(IS_RTC_ALARM(RTC_Alarm)); + + /* Get the RTC_ALRMxR register */ + if (RTC_Alarm == RTC_Alarm_A) + { + tmpreg = (uint32_t)(RTC->ALRMAR); + } + else + { + tmpreg = (uint32_t)(RTC->ALRMBR); + } + + /* Fill the structure with the read parameters */ + RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours = (uint32_t)((tmpreg & (RTC_ALRMAR_HT | \ + RTC_ALRMAR_HU)) >> 16); + RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes = (uint32_t)((tmpreg & (RTC_ALRMAR_MNT | \ + RTC_ALRMAR_MNU)) >> 8); + RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds = (uint32_t)(tmpreg & (RTC_ALRMAR_ST | \ + RTC_ALRMAR_SU)); + RTC_AlarmStruct->RTC_AlarmTime.RTC_H12 = (uint32_t)((tmpreg & RTC_ALRMAR_PM) >> 16); + RTC_AlarmStruct->RTC_AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> 24); + RTC_AlarmStruct->RTC_AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL); + RTC_AlarmStruct->RTC_AlarmMask = (uint32_t)(tmpreg & RTC_AlarmMask_All); + + if (RTC_Format == RTC_Format_BIN) + { + RTC_AlarmStruct->RTC_AlarmTime.RTC_Hours = RTC_Bcd2ToByte(RTC_AlarmStruct-> \ + RTC_AlarmTime.RTC_Hours); + RTC_AlarmStruct->RTC_AlarmTime.RTC_Minutes = RTC_Bcd2ToByte(RTC_AlarmStruct-> \ + RTC_AlarmTime.RTC_Minutes); + RTC_AlarmStruct->RTC_AlarmTime.RTC_Seconds = RTC_Bcd2ToByte(RTC_AlarmStruct-> \ + RTC_AlarmTime.RTC_Seconds); + RTC_AlarmStruct->RTC_AlarmDateWeekDay = RTC_Bcd2ToByte(RTC_AlarmStruct->RTC_AlarmDateWeekDay); + } +} + +/** + * @brief Enables or disables the specified RTC Alarm. + * @param RTC_Alarm: specifies the alarm to be configured. + * This parameter can be any combination of the following values: + * @arg RTC_Alarm_A: to select Alarm A. + * @arg RTC_Alarm_B: to select Alarm B. + * @param NewState: new state of the specified alarm. + * This parameter can be: ENABLE or DISABLE. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Alarm is enabled/disabled + * - ERROR: RTC Alarm is not enabled/disabled + */ +ErrorStatus RTC_AlarmCmd(uint32_t RTC_Alarm, FunctionalState NewState) +{ + __IO uint32_t alarmcounter = 0x00; + uint32_t alarmstatus = 0x00; + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_RTC_CMD_ALARM(RTC_Alarm)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Configure the Alarm state */ + if (NewState != DISABLE) + { + RTC->CR |= (uint32_t)RTC_Alarm; + + status = SUCCESS; + } + else + { + /* Disable the Alarm in RTC_CR register */ + RTC->CR &= (uint32_t)~RTC_Alarm; + + /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ + do + { + alarmstatus = RTC->ISR & (RTC_Alarm >> 8); + alarmcounter++; + } while((alarmcounter != INITMODE_TIMEOUT) && (alarmstatus == 0x00)); + + if ((RTC->ISR & (RTC_Alarm >> 8)) == RESET) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Configure the RTC AlarmA/B Subseconds value and mask.* + * @note This function is performed only when the Alarm is disabled. + * @param RTC_Alarm: specifies the alarm to be configured. + * This parameter can be one of the following values: + * @arg RTC_Alarm_A: to select Alarm A. + * @arg RTC_Alarm_B: to select Alarm B. + * @param RTC_AlarmSubSecondValue: specifies the Subseconds value. + * This parameter can be a value from 0 to 0x00007FFF. + * @param RTC_AlarmSubSecondMask: specifies the Subseconds Mask. + * This parameter can be any combination of the following values: + * @arg RTC_AlarmSubSecondMask_All: All Alarm SS fields are masked. + * There is no comparison on sub seconds for Alarm. + * @arg RTC_AlarmSubSecondMask_SS14_1: SS[14:1] are don't care in Alarm comparison. + * Only SS[0] is compared + * @arg RTC_AlarmSubSecondMask_SS14_2: SS[14:2] are don't care in Alarm comparison. + * Only SS[1:0] are compared + * @arg RTC_AlarmSubSecondMask_SS14_3: SS[14:3] are don't care in Alarm comparison. + * Only SS[2:0] are compared + * @arg RTC_AlarmSubSecondMask_SS14_4: SS[14:4] are don't care in Alarm comparison. + * Only SS[3:0] are compared + * @arg RTC_AlarmSubSecondMask_SS14_5: SS[14:5] are don't care in Alarm comparison. + * Only SS[4:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_6: SS[14:6] are don't care in Alarm comparison. + * Only SS[5:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_7: SS[14:7] are don't care in Alarm comparison. + * Only SS[6:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_8: SS[14:8] are don't care in Alarm comparison. + * Only SS[7:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_9: SS[14:9] are don't care in Alarm comparison. + * Only SS[8:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_10: SS[14:10] are don't care in Alarm comparison. + * Only SS[9:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_11: SS[14:11] are don't care in Alarm comparison. + * Only SS[10:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_12: SS[14:12] are don't care in Alarm comparison. + * Only SS[11:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14_13: SS[14:13] are don't care in Alarm comparison. + * Only SS[12:0] are compared. + * @arg RTC_AlarmSubSecondMask_SS14: SS[14] is don't care in Alarm comparison. + * Only SS[13:0] are compared. + * @arg RTC_AlarmSubSecondMask_None: SS[14:0] are compared and must match + * to activate alarm. + * @retval None + */ +void RTC_AlarmSubSecondConfig(uint32_t RTC_Alarm, uint32_t RTC_AlarmSubSecondValue, uint32_t RTC_AlarmSubSecondMask) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_ALARM(RTC_Alarm)); + assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(RTC_AlarmSubSecondValue)); + assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(RTC_AlarmSubSecondMask)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Configure the Alarm A or Alarm B SubSecond registers */ + tmpreg = (uint32_t) (uint32_t)(RTC_AlarmSubSecondValue) | (uint32_t)(RTC_AlarmSubSecondMask); + + if (RTC_Alarm == RTC_Alarm_A) + { + /* Configure the AlarmA SubSecond register */ + RTC->ALRMASSR = tmpreg; + } + else + { + /* Configure the Alarm B SubSecond register */ + RTC->ALRMBSSR = tmpreg; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + +} + +/** + * @brief Gets the RTC Alarm Subseconds value. + * @param RTC_Alarm: specifies the alarm to be read. + * This parameter can be one of the following values: + * @arg RTC_Alarm_A: to select Alarm A. + * @arg RTC_Alarm_B: to select Alarm B. + * @param None + * @retval RTC Alarm Subseconds value. + */ +uint32_t RTC_GetAlarmSubSecond(uint32_t RTC_Alarm) +{ + uint32_t tmpreg = 0; + + /* Get the RTC_ALRMxR register */ + if (RTC_Alarm == RTC_Alarm_A) + { + tmpreg = (uint32_t)((RTC->ALRMASSR) & RTC_ALRMASSR_SS); + } + else + { + tmpreg = (uint32_t)((RTC->ALRMBSSR) & RTC_ALRMBSSR_SS); + } + + return (tmpreg); +} + +/** + * @} + */ + +/** @defgroup RTC_Group4 WakeUp Timer configuration functions + * @brief WakeUp Timer configuration functions + * +@verbatim + =============================================================================== + ##### WakeUp Timer configuration functions ##### + =============================================================================== + [..] This section provide functions allowing to program and read the RTC WakeUp. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the RTC Wakeup clock source. + * @note The WakeUp Clock source can only be changed when the RTC WakeUp + * is disabled (Use the RTC_WakeUpCmd(DISABLE)). + * @param RTC_WakeUpClock: Wakeup Clock source. + * This parameter can be one of the following values: + * @arg RTC_WakeUpClock_RTCCLK_Div16: RTC Wakeup Counter Clock = RTCCLK/16. + * @arg RTC_WakeUpClock_RTCCLK_Div8: RTC Wakeup Counter Clock = RTCCLK/8. + * @arg RTC_WakeUpClock_RTCCLK_Div4: RTC Wakeup Counter Clock = RTCCLK/4. + * @arg RTC_WakeUpClock_RTCCLK_Div2: RTC Wakeup Counter Clock = RTCCLK/2. + * @arg RTC_WakeUpClock_CK_SPRE_16bits: RTC Wakeup Counter Clock = CK_SPRE. + * @arg RTC_WakeUpClock_CK_SPRE_17bits: RTC Wakeup Counter Clock = CK_SPRE. + * @retval None + */ +void RTC_WakeUpClockConfig(uint32_t RTC_WakeUpClock) +{ + /* Check the parameters */ + assert_param(IS_RTC_WAKEUP_CLOCK(RTC_WakeUpClock)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Clear the Wakeup Timer clock source bits in CR register */ + RTC->CR &= (uint32_t)~RTC_CR_WUCKSEL; + + /* Configure the clock source */ + RTC->CR |= (uint32_t)RTC_WakeUpClock; + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Configures the RTC Wakeup counter. + * @note The RTC WakeUp counter can only be written when the RTC WakeUp. + * is disabled (Use the RTC_WakeUpCmd(DISABLE)). + * @param RTC_WakeUpCounter: specifies the WakeUp counter. + * This parameter can be a value from 0x0000 to 0xFFFF. + * @retval None + */ +void RTC_SetWakeUpCounter(uint32_t RTC_WakeUpCounter) +{ + /* Check the parameters */ + assert_param(IS_RTC_WAKEUP_COUNTER(RTC_WakeUpCounter)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Configure the Wakeup Timer counter */ + RTC->WUTR = (uint32_t)RTC_WakeUpCounter; + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Returns the RTC WakeUp timer counter value. + * @param None + * @retval The RTC WakeUp Counter value. + */ +uint32_t RTC_GetWakeUpCounter(void) +{ + /* Get the counter value */ + return ((uint32_t)(RTC->WUTR & RTC_WUTR_WUT)); +} + +/** + * @brief Enables or Disables the RTC WakeUp timer. + * @param NewState: new state of the WakeUp timer. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +ErrorStatus RTC_WakeUpCmd(FunctionalState NewState) +{ + __IO uint32_t wutcounter = 0x00; + uint32_t wutwfstatus = 0x00; + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + if (NewState != DISABLE) + { + /* Enable the Wakeup Timer */ + RTC->CR |= (uint32_t)RTC_CR_WUTE; + status = SUCCESS; + } + else + { + /* Disable the Wakeup Timer */ + RTC->CR &= (uint32_t)~RTC_CR_WUTE; + /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ + do + { + wutwfstatus = RTC->ISR & RTC_ISR_WUTWF; + wutcounter++; + } while((wutcounter != INITMODE_TIMEOUT) && (wutwfstatus == 0x00)); + + if ((RTC->ISR & RTC_ISR_WUTWF) == RESET) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @} + */ + +/** @defgroup RTC_Group5 Daylight Saving configuration functions + * @brief Daylight Saving configuration functions + * +@verbatim + =============================================================================== + ##### Daylight Saving configuration functions ##### + =============================================================================== + [..] This section provide functions allowing to configure the RTC DayLight Saving. + +@endverbatim + * @{ + */ + +/** + * @brief Adds or substract one hour from the current time. + * @param RTC_DayLightSaveOperation: the value of hour adjustment. + * This parameter can be one of the following values: + * @arg RTC_DayLightSaving_SUB1H: Substract one hour (winter time). + * @arg RTC_DayLightSaving_ADD1H: Add one hour (summer time). + * @param RTC_StoreOperation: Specifies the value to be written in the BCK bit + * in CR register to store the operation. + * This parameter can be one of the following values: + * @arg RTC_StoreOperation_Reset: BCK Bit Reset. + * @arg RTC_StoreOperation_Set: BCK Bit Set. + * @retval None + */ +void RTC_DayLightSavingConfig(uint32_t RTC_DayLightSaving, uint32_t RTC_StoreOperation) +{ + /* Check the parameters */ + assert_param(IS_RTC_DAYLIGHT_SAVING(RTC_DayLightSaving)); + assert_param(IS_RTC_STORE_OPERATION(RTC_StoreOperation)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Clear the bits to be configured */ + RTC->CR &= (uint32_t)~(RTC_CR_BCK); + + /* Configure the RTC_CR register */ + RTC->CR |= (uint32_t)(RTC_DayLightSaving | RTC_StoreOperation); + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Returns the RTC Day Light Saving stored operation. + * @param None + * @retval RTC Day Light Saving stored operation. + * - RTC_StoreOperation_Reset + * - RTC_StoreOperation_Set + */ +uint32_t RTC_GetStoreOperation(void) +{ + return (RTC->CR & RTC_CR_BCK); +} + +/** + * @} + */ + +/** @defgroup RTC_Group6 Output pin Configuration function + * @brief Output pin Configuration function + * +@verbatim + =============================================================================== + ##### Output pin Configuration function ##### + =============================================================================== + [..] This section provide functions allowing to configure the RTC Output source. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the RTC output source (AFO_ALARM). + * @param RTC_Output: Specifies which signal will be routed to the RTC output. + * This parameter can be one of the following values: + * @arg RTC_Output_Disable: No output selected + * @arg RTC_Output_AlarmA: signal of AlarmA mapped to output. + * @arg RTC_Output_AlarmB: signal of AlarmB mapped to output. + * @arg RTC_Output_WakeUp: signal of WakeUp mapped to output. + * @param RTC_OutputPolarity: Specifies the polarity of the output signal. + * This parameter can be one of the following: + * @arg RTC_OutputPolarity_High: The output pin is high when the + * ALRAF/ALRBF/WUTF is high (depending on OSEL). + * @arg RTC_OutputPolarity_Low: The output pin is low when the + * ALRAF/ALRBF/WUTF is high (depending on OSEL). + * @retval None + */ +void RTC_OutputConfig(uint32_t RTC_Output, uint32_t RTC_OutputPolarity) +{ + /* Check the parameters */ + assert_param(IS_RTC_OUTPUT(RTC_Output)); + assert_param(IS_RTC_OUTPUT_POL(RTC_OutputPolarity)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Clear the bits to be configured */ + RTC->CR &= (uint32_t)~(RTC_CR_OSEL | RTC_CR_POL); + + /* Configure the output selection and polarity */ + RTC->CR |= (uint32_t)(RTC_Output | RTC_OutputPolarity); + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @} + */ + +/** @defgroup RTC_Group7 Coarse and Smooth Calibrations configuration functions + * @brief Coarse and Smooth Calibrations configuration functions + * +@verbatim + =============================================================================== + ##### Coarse and Smooth Calibrations configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Configures the Coarse Calibration parameters. + * @param RTC_CalibSign: specifies the sign of the calibration value. + * This parameter can be one of the following values: + * @arg RTC_CalibSign_Positive: The value sign is positive. + * @arg RTC_CalibSign_Negative: The value sign is negative. + * @param Value: value of calibration expressed in ppm (coded on 5 bits) + * This value should be between 0 and 63 when using negative sign + * with a 2-ppm step. + * This value should be between 0 and 126 when using positive sign + * with a 4-ppm step. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Coarse calibration are initialized + * - ERROR: RTC Coarse calibration are not initialized + */ +ErrorStatus RTC_CoarseCalibConfig(uint32_t RTC_CalibSign, uint32_t Value) +{ + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_RTC_CALIB_SIGN(RTC_CalibSign)); + assert_param(IS_RTC_CALIB_VALUE(Value)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + /* Set the coarse calibration value */ + RTC->CALIBR = (uint32_t)(RTC_CalibSign | Value); + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + status = SUCCESS; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** +* @brief Enables or disables the Coarse calibration process. + * @param NewState: new state of the Coarse calibration. + * This parameter can be: ENABLE or DISABLE. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Coarse calibration are enabled/disabled + * - ERROR: RTC Coarse calibration are not enabled/disabled + */ +ErrorStatus RTC_CoarseCalibCmd(FunctionalState NewState) +{ + ErrorStatus status = ERROR; + + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Set Initialization mode */ + if (RTC_EnterInitMode() == ERROR) + { + status = ERROR; + } + else + { + if (NewState != DISABLE) + { + /* Enable the Coarse Calibration */ + RTC->CR |= (uint32_t)RTC_CR_DCE; + } + else + { + /* Disable the Coarse Calibration */ + RTC->CR &= (uint32_t)~RTC_CR_DCE; + } + /* Exit Initialization mode */ + RTC_ExitInitMode(); + + status = SUCCESS; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return status; +} + +/** + * @brief Enables or disables the RTC clock to be output through the relative + * pin. + * @param NewState: new state of the coarse calibration Output. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_CalibOutputCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + if (NewState != DISABLE) + { + /* Enable the RTC clock output */ + RTC->CR |= (uint32_t)RTC_CR_COE; + } + else + { + /* Disable the RTC clock output */ + RTC->CR &= (uint32_t)~RTC_CR_COE; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). + * @param RTC_CalibOutput : Select the Calibration output Selection . + * This parameter can be one of the following values: + * @arg RTC_CalibOutput_512Hz: A signal has a regular waveform at 512Hz. + * @arg RTC_CalibOutput_1Hz: A signal has a regular waveform at 1Hz. + * @retval None +*/ +void RTC_CalibOutputConfig(uint32_t RTC_CalibOutput) +{ + /* Check the parameters */ + assert_param(IS_RTC_CALIB_OUTPUT(RTC_CalibOutput)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /*clear flags before config*/ + RTC->CR &= (uint32_t)~(RTC_CR_COSEL); + + /* Configure the RTC_CR register */ + RTC->CR |= (uint32_t)RTC_CalibOutput; + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Configures the Smooth Calibration Settings. + * @param RTC_SmoothCalibPeriod: Select the Smooth Calibration Period. + * This parameter can be can be one of the following values: + * @arg RTC_SmoothCalibPeriod_32sec: The smooth calibration periode is 32s. + * @arg RTC_SmoothCalibPeriod_16sec: The smooth calibration periode is 16s. + * @arg RTC_SmoothCalibPeriod_8sec: The smooth calibartion periode is 8s. + * @param RTC_SmoothCalibPlusPulses: Select to Set or reset the CALP bit. + * This parameter can be one of the following values: + * @arg RTC_SmoothCalibPlusPulses_Set: Add one RTCCLK puls every 2**11 pulses. + * @arg RTC_SmoothCalibPlusPulses_Reset: No RTCCLK pulses are added. + * @param RTC_SmouthCalibMinusPulsesValue: Select the value of CALM[8:0] bits. + * This parameter can be one any value from 0 to 0x000001FF. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Calib registers are configured + * - ERROR: RTC Calib registers are not configured +*/ +ErrorStatus RTC_SmoothCalibConfig(uint32_t RTC_SmoothCalibPeriod, + uint32_t RTC_SmoothCalibPlusPulses, + uint32_t RTC_SmouthCalibMinusPulsesValue) +{ + ErrorStatus status = ERROR; + uint32_t recalpfcount = 0; + + /* Check the parameters */ + assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(RTC_SmoothCalibPeriod)); + assert_param(IS_RTC_SMOOTH_CALIB_PLUS(RTC_SmoothCalibPlusPulses)); + assert_param(IS_RTC_SMOOTH_CALIB_MINUS(RTC_SmouthCalibMinusPulsesValue)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* check if a calibration is pending*/ + if ((RTC->ISR & RTC_ISR_RECALPF) != RESET) + { + /* wait until the Calibration is completed*/ + while (((RTC->ISR & RTC_ISR_RECALPF) != RESET) && (recalpfcount != RECALPF_TIMEOUT)) + { + recalpfcount++; + } + } + + /* check if the calibration pending is completed or if there is no calibration operation at all*/ + if ((RTC->ISR & RTC_ISR_RECALPF) == RESET) + { + /* Configure the Smooth calibration settings */ + RTC->CALR = (uint32_t)((uint32_t)RTC_SmoothCalibPeriod | (uint32_t)RTC_SmoothCalibPlusPulses | (uint32_t)RTC_SmouthCalibMinusPulsesValue); + + status = SUCCESS; + } + else + { + status = ERROR; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return (ErrorStatus)(status); +} + +/** + * @} + */ + + +/** @defgroup RTC_Group8 TimeStamp configuration functions + * @brief TimeStamp configuration functions + * +@verbatim + =============================================================================== + ##### TimeStamp configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Enables or Disables the RTC TimeStamp functionality with the + * specified time stamp pin stimulating edge. + * @param RTC_TimeStampEdge: Specifies the pin edge on which the TimeStamp is + * activated. + * This parameter can be one of the following: + * @arg RTC_TimeStampEdge_Rising: the Time stamp event occurs on the rising + * edge of the related pin. + * @arg RTC_TimeStampEdge_Falling: the Time stamp event occurs on the + * falling edge of the related pin. + * @param NewState: new state of the TimeStamp. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_TimeStampCmd(uint32_t RTC_TimeStampEdge, FunctionalState NewState) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_TIMESTAMP_EDGE(RTC_TimeStampEdge)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Get the RTC_CR register and clear the bits to be configured */ + tmpreg = (uint32_t)(RTC->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); + + /* Get the new configuration */ + if (NewState != DISABLE) + { + tmpreg |= (uint32_t)(RTC_TimeStampEdge | RTC_CR_TSE); + } + else + { + tmpreg |= (uint32_t)(RTC_TimeStampEdge); + } + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Configure the Time Stamp TSEDGE and Enable bits */ + RTC->CR = (uint32_t)tmpreg; + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Get the RTC TimeStamp value and masks. + * @param RTC_Format: specifies the format of the output parameters. + * This parameter can be one of the following values: + * @arg RTC_Format_BIN: Binary data format + * @arg RTC_Format_BCD: BCD data format + * @param RTC_StampTimeStruct: pointer to a RTC_TimeTypeDef structure that will + * contains the TimeStamp time values. + * @param RTC_StampDateStruct: pointer to a RTC_DateTypeDef structure that will + * contains the TimeStamp date values. + * @retval None + */ +void RTC_GetTimeStamp(uint32_t RTC_Format, RTC_TimeTypeDef* RTC_StampTimeStruct, + RTC_DateTypeDef* RTC_StampDateStruct) +{ + uint32_t tmptime = 0, tmpdate = 0; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(RTC_Format)); + + /* Get the TimeStamp time and date registers values */ + tmptime = (uint32_t)(RTC->TSTR & RTC_TR_RESERVED_MASK); + tmpdate = (uint32_t)(RTC->TSDR & RTC_DR_RESERVED_MASK); + + /* Fill the Time structure fields with the read parameters */ + RTC_StampTimeStruct->RTC_Hours = (uint8_t)((tmptime & (RTC_TR_HT | RTC_TR_HU)) >> 16); + RTC_StampTimeStruct->RTC_Minutes = (uint8_t)((tmptime & (RTC_TR_MNT | RTC_TR_MNU)) >> 8); + RTC_StampTimeStruct->RTC_Seconds = (uint8_t)(tmptime & (RTC_TR_ST | RTC_TR_SU)); + RTC_StampTimeStruct->RTC_H12 = (uint8_t)((tmptime & (RTC_TR_PM)) >> 16); + + /* Fill the Date structure fields with the read parameters */ + RTC_StampDateStruct->RTC_Year = 0; + RTC_StampDateStruct->RTC_Month = (uint8_t)((tmpdate & (RTC_DR_MT | RTC_DR_MU)) >> 8); + RTC_StampDateStruct->RTC_Date = (uint8_t)(tmpdate & (RTC_DR_DT | RTC_DR_DU)); + RTC_StampDateStruct->RTC_WeekDay = (uint8_t)((tmpdate & (RTC_DR_WDU)) >> 13); + + /* Check the input parameters format */ + if (RTC_Format == RTC_Format_BIN) + { + /* Convert the Time structure parameters to Binary format */ + RTC_StampTimeStruct->RTC_Hours = (uint8_t)RTC_Bcd2ToByte(RTC_StampTimeStruct->RTC_Hours); + RTC_StampTimeStruct->RTC_Minutes = (uint8_t)RTC_Bcd2ToByte(RTC_StampTimeStruct->RTC_Minutes); + RTC_StampTimeStruct->RTC_Seconds = (uint8_t)RTC_Bcd2ToByte(RTC_StampTimeStruct->RTC_Seconds); + + /* Convert the Date structure parameters to Binary format */ + RTC_StampDateStruct->RTC_Month = (uint8_t)RTC_Bcd2ToByte(RTC_StampDateStruct->RTC_Month); + RTC_StampDateStruct->RTC_Date = (uint8_t)RTC_Bcd2ToByte(RTC_StampDateStruct->RTC_Date); + RTC_StampDateStruct->RTC_WeekDay = (uint8_t)RTC_Bcd2ToByte(RTC_StampDateStruct->RTC_WeekDay); + } +} + +/** + * @brief Get the RTC timestamp Subseconds value. + * @param None + * @retval RTC current timestamp Subseconds value. + */ +uint32_t RTC_GetTimeStampSubSecond(void) +{ + /* Get timestamp subseconds values from the correspondent registers */ + return (uint32_t)(RTC->TSSSR); +} + +/** + * @} + */ + +/** @defgroup RTC_Group9 Tampers configuration functions + * @brief Tampers configuration functions + * +@verbatim + =============================================================================== + ##### Tampers configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Configures the select Tamper pin edge. + * @param RTC_Tamper: Selected tamper pin. + * This parameter can be any combination of the following values: + * @arg RTC_Tamper_1: Select Tamper 1. + * @arg RTC_Tamper_2: Select Tamper 2. + * @arg RTC_Tamper_3: Select Tamper 3. + * @param RTC_TamperTrigger: Specifies the trigger on the tamper pin that + * stimulates tamper event. + * This parameter can be one of the following values: + * @arg RTC_TamperTrigger_RisingEdge: Rising Edge of the tamper pin causes tamper event. + * @arg RTC_TamperTrigger_FallingEdge: Falling Edge of the tamper pin causes tamper event. + * @arg RTC_TamperTrigger_LowLevel: Low Level of the tamper pin causes tamper event. + * @arg RTC_TamperTrigger_HighLevel: High Level of the tamper pin causes tamper event. + * @retval None + */ +void RTC_TamperTriggerConfig(uint32_t RTC_Tamper, uint32_t RTC_TamperTrigger) +{ + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(RTC_Tamper)); + assert_param(IS_RTC_TAMPER_TRIGGER(RTC_TamperTrigger)); + + /* Check if the active level for Tamper is rising edge (Low level)*/ + if (RTC_TamperTrigger == RTC_TamperTrigger_RisingEdge) + { + /* Configure the RTC_TAFCR register */ + RTC->TAFCR &= (uint32_t)((uint32_t)~(RTC_Tamper << 1)); + } + else + { + /* Configure the RTC_TAFCR register */ + RTC->TAFCR |= (uint32_t)(RTC_Tamper << 1); + } +} + +/** + * @brief Enables or Disables the Tamper detection. + * @param RTC_Tamper: Selected tamper pin. + * This parameter can be any combination of the following values: + * @arg RTC_Tamper_1: Select Tamper 1. + * @arg RTC_Tamper_2: Select Tamper 2. + * @arg RTC_Tamper_3: Select Tamper 3. + * @param NewState: new state of the tamper pin. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_TamperCmd(uint32_t RTC_Tamper, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(RTC_Tamper)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the selected Tamper pin */ + RTC->TAFCR |= (uint32_t)RTC_Tamper; + } + else + { + /* Disable the selected Tamper pin */ + RTC->TAFCR &= (uint32_t)~RTC_Tamper; + } +} + +/** + * @brief Configures the Tampers Filter. + * @param RTC_TamperFilter: Specifies the tampers filter. + * This parameter can be one of the following values: + * @arg RTC_TamperFilter_Disable: Tamper filter is disabled. + * @arg RTC_TamperFilter_2Sample: Tamper is activated after 2 consecutive + * samples at the active level. + * @arg RTC_TamperFilter_4Sample: Tamper is activated after 4 consecutive + * samples at the active level. + * @arg RTC_TamperFilter_8Sample: Tamper is activated after 8 consecutive + * samples at the active level. + * @retval None + */ +void RTC_TamperFilterConfig(uint32_t RTC_TamperFilter) +{ + /* Check the parameters */ + assert_param(IS_RTC_TAMPER_FILTER(RTC_TamperFilter)); + + /* Clear TAMPFLT[1:0] bits in the RTC_TAFCR register */ + RTC->TAFCR &= (uint32_t)~(RTC_TAFCR_TAMPFLT); + + /* Configure the RTC_TAFCR register */ + RTC->TAFCR |= (uint32_t)RTC_TamperFilter; +} + +/** + * @brief Configures the Tampers Sampling Frequency. + * @param RTC_TamperSamplingFreq: Specifies the tampers Sampling Frequency. + * This parameter can be one of the following values: + * @arg RTC_TamperSamplingFreq_RTCCLK_Div32768: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 32768 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div16384: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 16384 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div8192: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 8192 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div4096: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 4096 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div2048: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 2048 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div1024: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 1024 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div512: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 512 + * @arg RTC_TamperSamplingFreq_RTCCLK_Div256: Each of the tamper inputs are sampled + * with a frequency = RTCCLK / 256 + * @retval None + */ +void RTC_TamperSamplingFreqConfig(uint32_t RTC_TamperSamplingFreq) +{ + /* Check the parameters */ + assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(RTC_TamperSamplingFreq)); + + /* Clear TAMPFREQ[2:0] bits in the RTC_TAFCR register */ + RTC->TAFCR &= (uint32_t)~(RTC_TAFCR_TAMPFREQ); + + /* Configure the RTC_TAFCR register */ + RTC->TAFCR |= (uint32_t)RTC_TamperSamplingFreq; +} + +/** + * @brief Configures the Tampers Pins input Precharge Duration. + * @param RTC_TamperPrechargeDuration: Specifies the Tampers Pins input + * Precharge Duration. + * This parameter can be one of the following values: + * @arg RTC_TamperPrechargeDuration_1RTCCLK: Tamper pins are pre-charged before sampling during 1 RTCCLK cycle. + * @arg RTC_TamperPrechargeDuration_2RTCCLK: Tamper pins are pre-charged before sampling during 2 RTCCLK cycle. + * @arg RTC_TamperPrechargeDuration_4RTCCLK: Tamper pins are pre-charged before sampling during 4 RTCCLK cycle. + * @arg RTC_TamperPrechargeDuration_8RTCCLK: Tamper pins are pre-charged before sampling during 8 RTCCLK cycle. + * @retval None + */ +void RTC_TamperPinsPrechargeDuration(uint32_t RTC_TamperPrechargeDuration) +{ + /* Check the parameters */ + assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(RTC_TamperPrechargeDuration)); + + /* Clear TAMPPRCH[1:0] bits in the RTC_TAFCR register */ + RTC->TAFCR &= (uint32_t)~(RTC_TAFCR_TAMPPRCH); + + /* Configure the RTC_TAFCR register */ + RTC->TAFCR |= (uint32_t)RTC_TamperPrechargeDuration; +} + +/** + * @brief Enables or Disables the TimeStamp on Tamper Detection Event. + * @note The timestamp is valid even the TSE bit in tamper control register + * is reset. + * @param NewState: new state of the timestamp on tamper event. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_TimeStampOnTamperDetectionCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Save timestamp on tamper detection event */ + RTC->TAFCR |= (uint32_t)RTC_TAFCR_TAMPTS; + } + else + { + /* Tamper detection does not cause a timestamp to be saved */ + RTC->TAFCR &= (uint32_t)~RTC_TAFCR_TAMPTS; + } +} + +/** + * @brief Enables or Disables the Precharge of Tamper pin. + * @param NewState: new state of tamper pull up. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_TamperPullUpCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable precharge of the selected Tamper pin */ + RTC->TAFCR &= (uint32_t)~RTC_TAFCR_TAMPPUDIS; + } + else + { + /* Disable precharge of the selected Tamper pin */ + RTC->TAFCR |= (uint32_t)RTC_TAFCR_TAMPPUDIS; + } +} + +/** + * @} + */ + +/** @defgroup RTC_Group10 Backup Data Registers configuration functions + * @brief Backup Data Registers configuration functions + * +@verbatim + =============================================================================== + ##### Backup Data Registers configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Writes a data in a specified RTC Backup data register. + * @param RTC_BKP_DR: RTC Backup data Register number. + * This parameter can be: RTC_BKP_DRx where x can be from 0 to 19 to + * specify the register. + * @param Data: Data to be written in the specified RTC Backup data register. + * @retval None + */ +void RTC_WriteBackupRegister(uint32_t RTC_BKP_DR, uint32_t Data) +{ + __IO uint32_t tmp = 0; + + /* Check the parameters */ + assert_param(IS_RTC_BKP(RTC_BKP_DR)); + + tmp = RTC_BASE + 0x50; + tmp += (RTC_BKP_DR * 4); + + /* Write the specified register */ + *(__IO uint32_t *)tmp = (uint32_t)Data; +} + +/** + * @brief Reads data from the specified RTC Backup data Register. + * @param RTC_BKP_DR: RTC Backup data Register number. + * This parameter can be: RTC_BKP_DRx where x can be from 0 to 19 to + * specify the register. + * @retval None + */ +uint32_t RTC_ReadBackupRegister(uint32_t RTC_BKP_DR) +{ + __IO uint32_t tmp = 0; + + /* Check the parameters */ + assert_param(IS_RTC_BKP(RTC_BKP_DR)); + + tmp = RTC_BASE + 0x50; + tmp += (RTC_BKP_DR * 4); + + /* Read the specified register */ + return (*(__IO uint32_t *)tmp); +} + +/** + * @} + */ + +/** @defgroup RTC_Group11 Output Type Config configuration functions + * @brief Output Type Config configuration functions + * +@verbatim + =============================================================================== + ##### Output Type Config configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Configures the RTC Output Pin mode. + * @param RTC_OutputType: specifies the RTC Output (PC13) pin mode. + * This parameter can be one of the following values: + * @arg RTC_OutputType_OpenDrain: RTC Output (PC13) is configured in + * Open Drain mode. + * @arg RTC_OutputType_PushPull: RTC Output (PC13) is configured in + * Push Pull mode. + * @retval None + */ +void RTC_OutputTypeConfig(uint32_t RTC_OutputType) +{ + /* Check the parameters */ + assert_param(IS_RTC_OUTPUT_TYPE(RTC_OutputType)); + + RTC->TAFCR &= (uint32_t)~(RTC_TAFCR_ALARMOUTTYPE); + RTC->TAFCR |= (uint32_t)(RTC_OutputType); +} + +/** + * @} + */ + +/** @defgroup RTC_Group12 Shift control synchronisation functions + * @brief Shift control synchronisation functions + * +@verbatim + =============================================================================== + ##### Shift control synchronisation functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Configures the Synchronization Shift Control Settings. + * @note When REFCKON is set, firmware must not write to Shift control register + * @param RTC_ShiftAdd1S : Select to add or not 1 second to the time Calendar. + * This parameter can be one of the following values : + * @arg RTC_ShiftAdd1S_Set: Add one second to the clock calendar. + * @arg RTC_ShiftAdd1S_Reset: No effect. + * @param RTC_ShiftSubFS: Select the number of Second Fractions to Substitute. + * This parameter can be one any value from 0 to 0x7FFF. + * @retval An ErrorStatus enumeration value: + * - SUCCESS: RTC Shift registers are configured + * - ERROR: RTC Shift registers are not configured +*/ +ErrorStatus RTC_SynchroShiftConfig(uint32_t RTC_ShiftAdd1S, uint32_t RTC_ShiftSubFS) +{ + ErrorStatus status = ERROR; + uint32_t shpfcount = 0; + + /* Check the parameters */ + assert_param(IS_RTC_SHIFT_ADD1S(RTC_ShiftAdd1S)); + assert_param(IS_RTC_SHIFT_SUBFS(RTC_ShiftSubFS)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + /* Check if a Shift is pending*/ + if ((RTC->ISR & RTC_ISR_SHPF) != RESET) + { + /* Wait until the shift is completed*/ + while (((RTC->ISR & RTC_ISR_SHPF) != RESET) && (shpfcount != SHPF_TIMEOUT)) + { + shpfcount++; + } + } + + /* Check if the Shift pending is completed or if there is no Shift operation at all*/ + if ((RTC->ISR & RTC_ISR_SHPF) == RESET) + { + /* check if the reference clock detection is disabled */ + if((RTC->CR & RTC_CR_REFCKON) == RESET) + { + /* Configure the Shift settings */ + RTC->SHIFTR = (uint32_t)(uint32_t)(RTC_ShiftSubFS) | (uint32_t)(RTC_ShiftAdd1S); + + if(RTC_WaitForSynchro() == ERROR) + { + status = ERROR; + } + else + { + status = SUCCESS; + } + } + else + { + status = ERROR; + } + } + else + { + status = ERROR; + } + + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; + + return (ErrorStatus)(status); +} + +/** + * @} + */ + +/** @defgroup RTC_Group13 Interrupts and flags management functions + * @brief Interrupts and flags management functions + * +@verbatim + =============================================================================== + ##### Interrupts and flags management functions ##### + =============================================================================== + [..] All RTC interrupts are connected to the EXTI controller. + (+) To enable the RTC Alarm interrupt, the following sequence is required: + (+) Configure and enable the EXTI Line 17 in interrupt mode and select + the rising edge sensitivity using the EXTI_Init() function. + (+) Configure and enable the RTC_Alarm IRQ channel in the NVIC using + the NVIC_Init() function. + (+) Configure the RTC to generate RTC alarms (Alarm A and/or Alarm B) + using the RTC_SetAlarm() and RTC_AlarmCmd() functions. + + (+) To enable the RTC Wakeup interrupt, the following sequence is required: + (+) Configure and enable the EXTI Line 20 in interrupt mode and select + the rising edge sensitivity using the EXTI_Init() function. + (+) Configure and enable the RTC_WKUP IRQ channel in the NVIC using the + NVIC_Init() function. + (+) Configure the RTC to generate the RTC wakeup timer event using the + RTC_WakeUpClockConfig(), RTC_SetWakeUpCounter() and RTC_WakeUpCmd() + functions. + + (+) To enable the RTC Tamper interrupt, the following sequence is required: + (+) Configure and enable the EXTI Line 19 in interrupt mode and select + the rising edge sensitivity using the EXTI_Init() function. + (+) Configure and enable the TAMP_STAMP IRQ channel in the NVIC using + the NVIC_Init() function. + (+) Configure the RTC to detect the RTC tamper event using the + RTC_TamperTriggerConfig() and RTC_TamperCmd() functions. + + (+) To enable the RTC TimeStamp interrupt, the following sequence is + required: + (+) Configure and enable the EXTI Line 19 in interrupt mode and select + the rising edge sensitivity using the EXTI_Init() function. + (+) Configure and enable the TAMP_STAMP IRQ channel in the NVIC using + the NVIC_Init() function. + (+) Configure the RTC to detect the RTC time-stamp event using the + RTC_TimeStampCmd() functions. + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the specified RTC interrupts. + * @param RTC_IT: specifies the RTC interrupt sources to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg RTC_IT_TS: Time Stamp interrupt mask. + * @arg RTC_IT_WUT: WakeUp Timer interrupt mask. + * @arg RTC_IT_ALRB: Alarm B interrupt mask. + * @arg RTC_IT_ALRA: Alarm A interrupt mask. + * @arg RTC_IT_TAMP: Tamper event interrupt mask. + * @param NewState: new state of the specified RTC interrupts. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void RTC_ITConfig(uint32_t RTC_IT, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_RTC_CONFIG_IT(RTC_IT)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* Disable the write protection for RTC registers */ + RTC->WPR = 0xCA; + RTC->WPR = 0x53; + + if (NewState != DISABLE) + { + /* Configure the Interrupts in the RTC_CR register */ + RTC->CR |= (uint32_t)(RTC_IT & ~RTC_TAFCR_TAMPIE); + /* Configure the Tamper Interrupt in the RTC_TAFCR */ + RTC->TAFCR |= (uint32_t)(RTC_IT & RTC_TAFCR_TAMPIE); + } + else + { + /* Configure the Interrupts in the RTC_CR register */ + RTC->CR &= (uint32_t)~(RTC_IT & (uint32_t)~RTC_TAFCR_TAMPIE); + /* Configure the Tamper Interrupt in the RTC_TAFCR */ + RTC->TAFCR &= (uint32_t)~(RTC_IT & RTC_TAFCR_TAMPIE); + } + /* Enable the write protection for RTC registers */ + RTC->WPR = 0xFF; +} + +/** + * @brief Checks whether the specified RTC flag is set or not. + * @param RTC_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg RTC_FLAG_RECALPF: RECALPF event flag. + * @arg RTC_FLAG_TAMP3F: Tamper 3 event flag. + * @arg RTC_FLAG_TAMP2F: Tamper 2 event flag. + * @arg RTC_FLAG_TAMP1F: Tamper 1 event flag. + * @arg RTC_FLAG_TSOVF: Time Stamp OverFlow flag. + * @arg RTC_FLAG_TSF: Time Stamp event flag. + * @arg RTC_FLAG_WUTF: WakeUp Timer flag. + * @arg RTC_FLAG_ALRBF: Alarm B flag. + * @arg RTC_FLAG_ALRAF: Alarm A flag. + * @arg RTC_FLAG_INITF: Initialization mode flag. + * @arg RTC_FLAG_RSF: Registers Synchronized flag. + * @arg RTC_FLAG_INITS: Registers Configured flag. + * @argRTC_FLAG_SHPF: Shift operation pending flag. + * @arg RTC_FLAG_WUTWF: WakeUp Timer Write flag. + * @arg RTC_FLAG_ALRBWF: Alarm B Write flag. + * @arg RTC_FLAG_ALRAWF: Alarm A write flag. + * @retval The new state of RTC_FLAG (SET or RESET). + */ +FlagStatus RTC_GetFlagStatus(uint32_t RTC_FLAG) +{ + FlagStatus bitstatus = RESET; + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_GET_FLAG(RTC_FLAG)); + + /* Get all the flags */ + tmpreg = (uint32_t)(RTC->ISR & RTC_FLAGS_MASK); + + /* Return the status of the flag */ + if ((tmpreg & RTC_FLAG) != (uint32_t)RESET) + { + bitstatus = SET; + } + else + { + bitstatus = RESET; + } + return bitstatus; +} + +/** + * @brief Clears the RTC's pending flags. + * @param RTC_FLAG: specifies the RTC flag to clear. + * This parameter can be any combination of the following values: + * @arg RTC_FLAG_TAMP3F: Tamper 3 event flag. + * @arg RTC_FLAG_TAMP2F: Tamper 2 event flag. + * @arg RTC_FLAG_TAMP1F: Tamper 1 event flag. + * @arg RTC_FLAG_TSOVF: Time Stamp Overflow flag. + * @arg RTC_FLAG_TSF: Time Stamp event flag. + * @arg RTC_FLAG_WUTF: WakeUp Timer flag. + * @arg RTC_FLAG_ALRBF: Alarm B flag. + * @arg RTC_FLAG_ALRAF: Alarm A flag. + * @arg RTC_FLAG_RSF: Registers Synchronized flag. + * @retval None + */ +void RTC_ClearFlag(uint32_t RTC_FLAG) +{ + /* Check the parameters */ + assert_param(IS_RTC_CLEAR_FLAG(RTC_FLAG)); + + /* Clear the Flags in the RTC_ISR register */ + RTC->ISR = (uint32_t)((uint32_t)(~((RTC_FLAG | RTC_ISR_INIT)& 0x0001FFFF) | (uint32_t)(RTC->ISR & RTC_ISR_INIT))); +} + +/** + * @brief Checks whether the specified RTC interrupt has occurred or not. + * @param RTC_IT: specifies the RTC interrupt source to check. + * This parameter can be one of the following values: + * @arg RTC_IT_TS: Time Stamp interrupt. + * @arg RTC_IT_WUT: WakeUp Timer interrupt. + * @arg RTC_IT_ALRB: Alarm B interrupt. + * @arg RTC_IT_ALRA: Alarm A interrupt. + * @arg RTC_IT_TAMP1: Tamper1 event interrupt. + * @arg RTC_IT_TAMP2: Tamper2 event interrupt. + * @arg RTC_IT_TAMP3: Tamper3 event interrupt. + * @retval The new state of RTC_IT (SET or RESET). + */ +ITStatus RTC_GetITStatus(uint32_t RTC_IT) +{ + ITStatus bitstatus = RESET; + uint32_t tmpreg = 0, enablestatus = 0; + + /* Check the parameters */ + assert_param(IS_RTC_GET_IT(RTC_IT)); + + /* Get the TAMPER Interrupt enable bit and pending bit */ + tmpreg = (uint32_t)(RTC->TAFCR & (RTC_TAFCR_TAMPIE)); + + /* Get the Interrupt enable Status */ + enablestatus = (uint32_t)((RTC->CR & RTC_IT) | (tmpreg & ((RTC_IT >> (RTC_IT >> 18)) >> 15))); + + /* Get the Interrupt pending bit */ + tmpreg = (uint32_t)((RTC->ISR & (uint32_t)(RTC_IT >> 4))); + + /* Get the status of the Interrupt */ + if ((enablestatus != (uint32_t)RESET) && ((tmpreg & 0x0000FFFF) != (uint32_t)RESET)) + { + bitstatus = SET; + } + else + { + bitstatus = RESET; + } + return bitstatus; +} + +/** + * @brief Clears the RTC's interrupt pending bits. + * @param RTC_IT: specifies the RTC interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg RTC_IT_TS: Time Stamp interrupt + * @arg RTC_IT_WUT: WakeUp Timer interrupt + * @arg RTC_IT_ALRB: Alarm B interrupt + * @arg RTC_IT_ALRA: Alarm A interrupt + * @arg RTC_IT_TAMP1: Tamper1 event interrupt + * @arg RTC_IT_TAMP2: Tamper2 event interrupt + * @arg RTC_IT_TAMP3: Tamper3 event interrupt + * @retval None + */ +void RTC_ClearITPendingBit(uint32_t RTC_IT) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_RTC_CLEAR_IT(RTC_IT)); + + /* Get the RTC_ISR Interrupt pending bits mask */ + tmpreg = (uint32_t)(RTC_IT >> 4); + + /* Clear the interrupt pending bits in the RTC_ISR register */ + RTC->ISR = (uint32_t)((uint32_t)(~((tmpreg | RTC_ISR_INIT)& 0x0000FFFF) | (uint32_t)(RTC->ISR & RTC_ISR_INIT))); +} + +/** + * @} + */ + +/** + * @brief Converts a 2 digit decimal to BCD format. + * @param Value: Byte to be converted. + * @retval Converted byte + */ +static uint8_t RTC_ByteToBcd2(uint8_t Value) +{ + uint8_t bcdhigh = 0; + + while (Value >= 10) + { + bcdhigh++; + Value -= 10; + } + + return ((uint8_t)(bcdhigh << 4) | Value); +} + +/** + * @brief Convert from 2 digit BCD to Binary. + * @param Value: BCD value to be converted. + * @retval Converted word + */ +static uint8_t RTC_Bcd2ToByte(uint8_t Value) +{ + uint8_t tmp = 0; + tmp = ((uint8_t)(Value & (uint8_t)0xF0) >> (uint8_t)0x4) * 10; + return (tmp + (Value & (uint8_t)0x0F)); +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/