mbed library sources
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_cec.c
- Revision:
- 130:1dec54e4aec3
diff -r 0182c99221bc -r 1dec54e4aec3 targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_cec.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_cec.c Fri Mar 21 11:45:09 2014 +0000 @@ -0,0 +1,617 @@ +/** + ****************************************************************************** + * @file stm32f0xx_cec.c + * @author MCD Application Team + * @version V1.3.0 + * @date 16-January-2014 + * @brief This file provides firmware functions to manage the following + * functionalities of the Consumer Electronics Control (CEC) peripheral + * applicable only on STM32F051, STM32F042 and STM32F072 devices: + * + Initialization and Configuration + * + Data transfers functions + * + Interrupts and flags management + * + * @verbatim + ============================================================================== + ##### CEC features ##### + ============================================================================== + [..] This device provides some features: + (#) Supports HDMI-CEC specification 1.4. + (#) Supports two source clocks(HSI/244 or LSE). + (#) Works in stop mode(without APB clock, but with CEC clock 32KHz). + It can genarate an interrupt in the CEC clock domain that the CPU + wakes up from the low power mode. + (#) Configurable Signal Free Time before of transmission start. The + number of nominal data bit periods waited before transmission can be + ruled by Hardware or Software. + (#) Configurable Peripheral Address (multi-addressing configuration). + (#) Supports listen mode.The CEC Messages addressed to different destination + can be received without interfering with CEC bus when Listen mode option is enabled. + (#) Configurable Rx-Tolerance(Standard and Extended tolerance margin). + (#) Error detection with configurable error bit generation. + (#) Arbitration lost error in the case of two CEC devices starting at the same time. + + ##### How to use this driver ##### + ============================================================================== + [..] This driver provides functions to configure and program the CEC device, + follow steps below: + (#) The source clock can be configured using: + (++) RCC_CECCLKConfig(RCC_CECCLK_HSI_Div244) for HSI(Default) + (++) RCC_CECCLKConfig(RCC_CECCLK_LSE) for LSE. + (#) Enable CEC peripheral clock using RCC_APBPeriphClockCmd(RCC_APBPeriph_CEC, ENABLE). + (#) Peripherals alternate function. + (++) Connect the pin to the desired peripherals' Alternate Function (AF) using + GPIO_PinAFConfig() function. + (++) Configure the desired pin in alternate function by: + GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF. + (++) Select the type open-drain and output speed via GPIO_OType + and GPIO_Speed members. + (++) Call GPIO_Init() function. + (#) Configure the Signal Free Time, Rx Tolerance, Stop reception generation + and Bit error generation using the CEC_Init() function. + The function CEC_Init() must be called when the CEC peripheral is disabled. + (#) Configure the CEC own address by calling the fuction CEC_OwnAddressConfig(). + (#) Optionally, you can configure the Listen mode using the function CEC_ListenModeCmd(). + (#) Enable the NVIC and the corresponding interrupt using the function + CEC_ITConfig() if you need to use interrupt mode. + CEC_ITConfig() must be called before enabling the CEC peripheral. + (#) Enable the CEC using the CEC_Cmd() function. + (#) Charge the first data byte in the TXDR register using CEC_SendDataByte(). + (#) Enable the transmission of the Byte of a CEC message using CEC_StartOfMessage() + (#) Transmit single data through the CEC peripheral using CEC_SendDataByte() + and Receive the last transmitted byte using CEC_ReceiveDataByte(). + (#) Enable the CEC_EndOfMessage() in order to indicate the last byte of the message. + [..] + (@) If the listen mode is enabled, Stop reception generation and Bit error generation + must be in reset state. + (@) If the CEC message consists of only 1 byte, the function CEC_EndOfMessage() + must be called before CEC_StartOfMessage(). + + @endverbatim + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx_cec.h" +#include "stm32f0xx_rcc.h" + +/** @addtogroup STM32F0xx_StdPeriph_Driver + * @{ + */ + +/** @defgroup CEC + * @brief CEC driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define BROADCAST_ADDRESS ((uint32_t)0x0000F) +#define CFGR_CLEAR_MASK ((uint32_t)0x7000FE00) /* CFGR register Mask */ + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup CEC_Private_Functions + * @{ + */ + +/** @defgroup CEC_Group1 Initialization and Configuration functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] This section provides functions allowing to initialize: + (+) CEC own addresses + (+) CEC Signal Free Time + (+) CEC Rx Tolerance + (+) CEC Stop Reception + (+) CEC Bit Rising Error + (+) CEC Long Bit Period Error + [..] This section provides also a function to configure the CEC peripheral in Listen Mode. + Messages addressed to different destination can be received when Listen mode is + enabled without interfering with CEC bus. +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the CEC peripheral registers to their default reset values. + * @param None + * @retval None + */ +void CEC_DeInit(void) +{ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_CEC, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_CEC, DISABLE); +} + +/** + * @brief Initializes the CEC peripheral according to the specified parameters + * in the CEC_InitStruct. + * @note The CEC parameters must be configured before enabling the CEC peripheral. + * @param CEC_InitStruct: pointer to an CEC_InitTypeDef structure that contains + * the configuration information for the specified CEC peripheral. + * @retval None + */ +void CEC_Init(CEC_InitTypeDef* CEC_InitStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_CEC_SIGNAL_FREE_TIME(CEC_InitStruct->CEC_SignalFreeTime)); + assert_param(IS_CEC_RX_TOLERANCE(CEC_InitStruct->CEC_RxTolerance)); + assert_param(IS_CEC_STOP_RECEPTION(CEC_InitStruct->CEC_StopReception)); + assert_param(IS_CEC_BIT_RISING_ERROR(CEC_InitStruct->CEC_BitRisingError)); + assert_param(IS_CEC_LONG_BIT_PERIOD_ERROR(CEC_InitStruct->CEC_LongBitPeriodError)); + assert_param(IS_CEC_BDR_NO_GEN_ERROR(CEC_InitStruct->CEC_BRDNoGen)); + assert_param(IS_CEC_SFT_OPTION(CEC_InitStruct->CEC_SFTOption)); + + /* Get the CEC CFGR value */ + tmpreg = CEC->CFGR; + + /* Clear CFGR bits */ + tmpreg &= CFGR_CLEAR_MASK; + + /* Configure the CEC peripheral */ + tmpreg |= (CEC_InitStruct->CEC_SignalFreeTime | CEC_InitStruct->CEC_RxTolerance | + CEC_InitStruct->CEC_StopReception | CEC_InitStruct->CEC_BitRisingError | + CEC_InitStruct->CEC_LongBitPeriodError| CEC_InitStruct->CEC_BRDNoGen | + CEC_InitStruct->CEC_SFTOption); + + /* Write to CEC CFGR register */ + CEC->CFGR = tmpreg; +} + +/** + * @brief Fills each CEC_InitStruct member with its default value. + * @param CEC_InitStruct: pointer to a CEC_InitTypeDef structure which will + * be initialized. + * @retval None + */ +void CEC_StructInit(CEC_InitTypeDef* CEC_InitStruct) +{ + CEC_InitStruct->CEC_SignalFreeTime = CEC_SignalFreeTime_Standard; + CEC_InitStruct->CEC_RxTolerance = CEC_RxTolerance_Standard; + CEC_InitStruct->CEC_StopReception = CEC_StopReception_Off; + CEC_InitStruct->CEC_BitRisingError = CEC_BitRisingError_Off; + CEC_InitStruct->CEC_LongBitPeriodError = CEC_LongBitPeriodError_Off; + CEC_InitStruct->CEC_BRDNoGen = CEC_BRDNoGen_Off; + CEC_InitStruct->CEC_SFTOption = CEC_SFTOption_Off; +} + +/** + * @brief Enables or disables the CEC peripheral. + * @param NewState: new state of the CEC peripheral. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CEC_Cmd(FunctionalState NewState) +{ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the CEC peripheral */ + CEC->CR |= CEC_CR_CECEN; + } + else + { + /* Disable the CEC peripheral */ + CEC->CR &= ~CEC_CR_CECEN; + } +} + +/** + * @brief Enables or disables the CEC Listen Mode. + * @param NewState: new state of the Listen Mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CEC_ListenModeCmd(FunctionalState NewState) +{ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the Listen Mode */ + CEC->CFGR |= CEC_CFGR_LSTN; + } + else + { + /* Disable the Listen Mode */ + CEC->CFGR &= ~CEC_CFGR_LSTN; + } +} + +/** + * @brief Defines the Own Address of the CEC device. + * @param CEC_OwnAddress: The CEC own address. + * @retval None + */ +void CEC_OwnAddressConfig(uint8_t CEC_OwnAddress) +{ + uint32_t tmp =0x00; + /* Check the parameters */ + assert_param(IS_CEC_ADDRESS(CEC_OwnAddress)); + tmp = 1 <<(CEC_OwnAddress + 16); + /* Set the CEC own address */ + CEC->CFGR |= tmp; +} + +/** + * @brief Clears the Own Address of the CEC device. + * @param CEC_OwnAddress: The CEC own address. + * @retval None + */ +void CEC_OwnAddressClear(void) +{ + /* Set the CEC own address */ + CEC->CFGR = 0x0; +} + +/** + * @} + */ + +/** @defgroup CEC_Group2 Data transfers functions + * @brief Data transfers functions + * +@verbatim + =============================================================================== + ##### Data transfers functions ##### + =============================================================================== + [..] This section provides functions allowing the CEC data transfers.The read + access of the CEC_RXDR register can be done using the CEC_ReceiveData()function + and returns the Rx buffered value. Whereas a write access to the CEC_TXDR can be + done using CEC_SendData() function. +@endverbatim + * @{ + */ + +/** + * @brief Transmits single data through the CEC peripheral. + * @param Data: the data to transmit. + * @retval None + */ +void CEC_SendData(uint8_t Data) +{ + /* Transmit Data */ + CEC->TXDR = Data; +} + +/** + * @brief Returns the most recent received data by the CEC peripheral. + * @param None + * @retval The received data. + */ +uint8_t CEC_ReceiveData(void) +{ + /* Receive Data */ + return (uint8_t)(CEC->RXDR); +} + +/** + * @brief Starts a new message. + * @param None + * @retval None + */ +void CEC_StartOfMessage(void) +{ + /* Starts of new message */ + CEC->CR |= CEC_CR_TXSOM; +} + +/** + * @brief Transmits message with an EOM bit. + * @param None + * @retval None + */ +void CEC_EndOfMessage(void) +{ + /* The data byte will be transmitted with an EOM bit */ + CEC->CR |= CEC_CR_TXEOM; +} + +/** + * @} + */ + +/** @defgroup CEC_Group3 Interrupts and flags management functions + * @brief Interrupts and flags management functions +* +@verbatim + =============================================================================== + ##### Interrupts and flags management functions ##### + =============================================================================== + [..] This section provides functions allowing to configure the CEC Interrupts + sources and check or clear the flags or pending bits status. + [..] The user should identify which mode will be used in his application to manage + the communication: Polling mode or Interrupt mode. + + [..] In polling mode, the CEC can be managed by the following flags: + (+) CEC_FLAG_TXACKE : to indicate a missing acknowledge in transmission mode. + (+) CEC_FLAG_TXERR : to indicate an error occurs during transmission mode. + The initiator detects low impedance in the CEC line. + (+) CEC_FLAG_TXUDR : to indicate if an underrun error occurs in transmission mode. + The transmission is enabled while the software has not yet + loaded any value into the TXDR register. + (+) CEC_FLAG_TXEND : to indicate the end of successful transmission. + (+) CEC_FLAG_TXBR : to indicate the next transmission data has to be written to TXDR. + (+) CEC_FLAG_ARBLST : to indicate arbitration lost in the case of two CEC devices + starting at the same time. + (+) CEC_FLAG_RXACKE : to indicate a missing acknowledge in receive mode. + (+) CEC_FLAG_LBPE : to indicate a long bit period error generated during receive mode. + (+) CEC_FLAG_SBPE : to indicate a short bit period error generated during receive mode. + (+) CEC_FLAG_BRE : to indicate a bit rising error generated during receive mode. + (+) CEC_FLAG_RXOVR : to indicate if an overrun error occur while receiving a CEC message. + A byte is not yet received while a new byte is stored in the RXDR register. + (+) CEC_FLAG_RXEND : to indicate the end Of reception + (+) CEC_FLAG_RXBR : to indicate a new byte has been received from the CEC line and + stored into the RXDR buffer. + [..] + (@)In this Mode, it is advised to use the following functions: + FlagStatus CEC_GetFlagStatus(uint16_t CEC_FLAG); + void CEC_ClearFlag(uint16_t CEC_FLAG); + + [..] In Interrupt mode, the CEC can be managed by the following interrupt sources: + (+) CEC_IT_TXACKE : to indicate a TX Missing acknowledge + (+) CEC_IT_TXACKE : to indicate a missing acknowledge in transmission mode. + (+) CEC_IT_TXERR : to indicate an error occurs during transmission mode. + The initiator detects low impedance in the CEC line. + (+) CEC_IT_TXUDR : to indicate if an underrun error occurs in transmission mode. + The transmission is enabled while the software has not yet + loaded any value into the TXDR register. + (+) CEC_IT_TXEND : to indicate the end of successful transmission. + (+) CEC_IT_TXBR : to indicate the next transmission data has to be written to TXDR register. + (+) CEC_IT_ARBLST : to indicate arbitration lost in the case of two CEC devices + starting at the same time. + (+) CEC_IT_RXACKE : to indicate a missing acknowledge in receive mode. + (+) CEC_IT_LBPE : to indicate a long bit period error generated during receive mode. + (+) CEC_IT_SBPE : to indicate a short bit period error generated during receive mode. + (+) CEC_IT_BRE : to indicate a bit rising error generated during receive mode. + (+) CEC_IT_RXOVR : to indicate if an overrun error occur while receiving a CEC message. + A byte is not yet received while a new byte is stored in the RXDR register. + (+) CEC_IT_RXEND : to indicate the end Of reception + (+) CEC_IT_RXBR : to indicate a new byte has been received from the CEC line and + stored into the RXDR buffer. + [..] + (@)In this Mode it is advised to use the following functions: + void CEC_ITConfig( uint16_t CEC_IT, FunctionalState NewState); + ITStatus CEC_GetITStatus(uint16_t CEC_IT); + void CEC_ClearITPendingBit(uint16_t CEC_IT); + + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the selected CEC interrupts. + * @param CEC_IT: specifies the CEC interrupt source to be enabled. + * This parameter can be any combination of the following values: + * @arg CEC_IT_TXACKE: Tx Missing acknowledge Error + * @arg CEC_IT_TXERR: Tx Error. + * @arg CEC_IT_TXUDR: Tx-Buffer Underrun. + * @arg CEC_IT_TXEND: End of Transmission (successful transmission of the last byte). + * @arg CEC_IT_TXBR: Tx-Byte Request. + * @arg CEC_IT_ARBLST: Arbitration Lost + * @arg CEC_IT_RXACKE: Rx-Missing Acknowledge + * @arg CEC_IT_LBPE: Rx Long period Error + * @arg CEC_IT_SBPE: Rx Short period Error + * @arg CEC_IT_BRE: Rx Bit Rising Error + * @arg CEC_IT_RXOVR: Rx Overrun. + * @arg CEC_IT_RXEND: End Of Reception + * @arg CEC_IT_RXBR: Rx-Byte Received + * @param NewState: new state of the selected CEC interrupts. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CEC_ITConfig(uint16_t CEC_IT, FunctionalState NewState) +{ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + assert_param(IS_CEC_IT(CEC_IT)); + + if (NewState != DISABLE) + { + /* Enable the selected CEC interrupt */ + CEC->IER |= CEC_IT; + } + else + { + CEC_IT =~CEC_IT; + /* Disable the selected CEC interrupt */ + CEC->IER &= CEC_IT; + } +} + +/** + * @brief Gets the CEC flag status. + * @param CEC_FLAG: specifies the CEC flag to check. + * This parameter can be one of the following values: + * @arg CEC_FLAG_TXACKE: Tx Missing acknowledge Error + * @arg CEC_FLAG_TXERR: Tx Error. + * @arg CEC_FLAG_TXUDR: Tx-Buffer Underrun. + * @arg CEC_FLAG_TXEND: End of transmission (successful transmission of the last byte). + * @arg CEC_FLAG_TXBR: Tx-Byte Request. + * @arg CEC_FLAG_ARBLST: Arbitration Lost + * @arg CEC_FLAG_RXACKE: Rx-Missing Acknowledge + * @arg CEC_FLAG_LBPE: Rx Long period Error + * @arg CEC_FLAG_SBPE: Rx Short period Error + * @arg CEC_FLAG_BRE: Rx Bit Rissing Error + * @arg CEC_FLAG_RXOVR: Rx Overrun. + * @arg CEC_FLAG_RXEND: End Of Reception. + * @arg CEC_FLAG_RXBR: Rx-Byte Received. + * @retval The new state of CEC_FLAG (SET or RESET) + */ +FlagStatus CEC_GetFlagStatus(uint16_t CEC_FLAG) +{ + FlagStatus bitstatus = RESET; + + assert_param(IS_CEC_GET_FLAG(CEC_FLAG)); + + /* Check the status of the specified CEC flag */ + if ((CEC->ISR & CEC_FLAG) != (uint16_t)RESET) + { + /* CEC flag is set */ + bitstatus = SET; + } + else + { + /* CEC flag is reset */ + bitstatus = RESET; + } + + /* Return the CEC flag status */ + return bitstatus; +} + +/** + * @brief Clears the CEC's pending flags. + * @param CEC_FLAG: specifies the flag to clear. + * This parameter can be any combination of the following values: + * @arg CEC_FLAG_TXACKE: Tx Missing acknowledge Error + * @arg CEC_FLAG_TXERR: Tx Error + * @arg CEC_FLAG_TXUDR: Tx-Buffer Underrun + * @arg CEC_FLAG_TXEND: End of transmission (successful transmission of the last byte). + * @arg CEC_FLAG_TXBR: Tx-Byte Request + * @arg CEC_FLAG_ARBLST: Arbitration Lost + * @arg CEC_FLAG_RXACKE: Rx Missing Acknowledge + * @arg CEC_FLAG_LBPE: Rx Long period Error + * @arg CEC_FLAG_SBPE: Rx Short period Error + * @arg CEC_FLAG_BRE: Rx Bit Rising Error + * @arg CEC_FLAG_RXOVR: Rx Overrun + * @arg CEC_FLAG_RXEND: End Of Reception + * @arg CEC_FLAG_RXBR: Rx-Byte Received + * @retval None + */ +void CEC_ClearFlag(uint32_t CEC_FLAG) +{ + assert_param(IS_CEC_CLEAR_FLAG(CEC_FLAG)); + + /* Clear the selected CEC flag */ + CEC->ISR = CEC_FLAG; +} + +/** + * @brief Checks whether the specified CEC interrupt has occurred or not. + * @param CEC_IT: specifies the CEC interrupt source to check. + * This parameter can be one of the following values: + * @arg CEC_IT_TXACKE: Tx Missing acknowledge Error + * @arg CEC_IT_TXERR: Tx Error. + * @arg CEC_IT_TXUDR: Tx-Buffer Underrun. + * @arg CEC_IT_TXEND: End of transmission (successful transmission of the last byte). + * @arg CEC_IT_TXBR: Tx-Byte Request. + * @arg CEC_IT_ARBLST: Arbitration Lost. + * @arg CEC_IT_RXACKE: Rx-Missing Acknowledge. + * @arg CEC_IT_LBPE: Rx Long period Error. + * @arg CEC_IT_SBPE: Rx Short period Error. + * @arg CEC_IT_BRE: Rx Bit Rising Error. + * @arg CEC_IT_RXOVR: Rx Overrun. + * @arg CEC_IT_RXEND: End Of Reception. + * @arg CEC_IT_RXBR: Rx-Byte Received + * @retval The new state of CEC_IT (SET or RESET). + */ +ITStatus CEC_GetITStatus(uint16_t CEC_IT) +{ + ITStatus bitstatus = RESET; + uint32_t enablestatus = 0; + + /* Check the parameters */ + assert_param(IS_CEC_GET_IT(CEC_IT)); + + /* Get the CEC IT enable bit status */ + enablestatus = (CEC->IER & CEC_IT); + + /* Check the status of the specified CEC interrupt */ + if (((CEC->ISR & CEC_IT) != (uint32_t)RESET) && enablestatus) + { + /* CEC interrupt is set */ + bitstatus = SET; + } + else + { + /* CEC interrupt is reset */ + bitstatus = RESET; + } + + /* Return the CEC interrupt status */ + return bitstatus; +} + +/** + * @brief Clears the CEC's interrupt pending bits. + * @param CEC_IT: specifies the CEC interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg CEC_IT_TXACKE: Tx Missing acknowledge Error + * @arg CEC_IT_TXERR: Tx Error + * @arg CEC_IT_TXUDR: Tx-Buffer Underrun + * @arg CEC_IT_TXEND: End of Transmission + * @arg CEC_IT_TXBR: Tx-Byte Request + * @arg CEC_IT_ARBLST: Arbitration Lost + * @arg CEC_IT_RXACKE: Rx-Missing Acknowledge + * @arg CEC_IT_LBPE: Rx Long period Error + * @arg CEC_IT_SBPE: Rx Short period Error + * @arg CEC_IT_BRE: Rx Bit Rising Error + * @arg CEC_IT_RXOVR: Rx Overrun + * @arg CEC_IT_RXEND: End Of Reception + * @arg CEC_IT_RXBR: Rx-Byte Received + * @retval None + */ +void CEC_ClearITPendingBit(uint16_t CEC_IT) +{ + assert_param(IS_CEC_IT(CEC_IT)); + + /* Clear the selected CEC interrupt pending bits */ + CEC->ISR = CEC_IT; +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/