mbed library sources
Fork of mbed-src by
targets/cmsis/TARGET_STM/TARGET_NUCLEO_F103RB/stm32f10x_spi.c
- Committer:
- mbed_official
- Date:
- 2014-01-07
- Revision:
- 70:c1fbde68b492
- Parent:
- 52:a51c77007319
- Child:
- 84:f54042cbc282
File content as of revision 70:c1fbde68b492:
/** ****************************************************************************** * @file stm32f10x_spi.c * @author MCD Application Team * @version V3.5.0 * @date 11-March-2011 * @brief This file provides all the SPI firmware functions. ******************************************************************************* * Copyright (c) 2014, STMicroelectronics * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ******************************************************************************* */ /* Includes ------------------------------------------------------------------*/ #include "stm32f10x_spi.h" #include "stm32f10x_rcc.h" /** @addtogroup STM32F10x_StdPeriph_Driver * @{ */ /** @defgroup SPI * @brief SPI driver modules * @{ */ /** @defgroup SPI_Private_TypesDefinitions * @{ */ /** * @} */ /** @defgroup SPI_Private_Defines * @{ */ /* SPI SPE mask */ #define CR1_SPE_Set ((uint16_t)0x0040) #define CR1_SPE_Reset ((uint16_t)0xFFBF) /* I2S I2SE mask */ #define I2SCFGR_I2SE_Set ((uint16_t)0x0400) #define I2SCFGR_I2SE_Reset ((uint16_t)0xFBFF) /* SPI CRCNext mask */ #define CR1_CRCNext_Set ((uint16_t)0x1000) /* SPI CRCEN mask */ #define CR1_CRCEN_Set ((uint16_t)0x2000) #define CR1_CRCEN_Reset ((uint16_t)0xDFFF) /* SPI SSOE mask */ #define CR2_SSOE_Set ((uint16_t)0x0004) #define CR2_SSOE_Reset ((uint16_t)0xFFFB) /* SPI registers Masks */ #define CR1_CLEAR_Mask ((uint16_t)0x3040) #define I2SCFGR_CLEAR_Mask ((uint16_t)0xF040) /* SPI or I2S mode selection masks */ #define SPI_Mode_Select ((uint16_t)0xF7FF) #define I2S_Mode_Select ((uint16_t)0x0800) /* I2S clock source selection masks */ #define I2S2_CLOCK_SRC ((uint32_t)(0x00020000)) #define I2S3_CLOCK_SRC ((uint32_t)(0x00040000)) #define I2S_MUL_MASK ((uint32_t)(0x0000F000)) #define I2S_DIV_MASK ((uint32_t)(0x000000F0)) /** * @} */ /** @defgroup SPI_Private_Macros * @{ */ /** * @} */ /** @defgroup SPI_Private_Variables * @{ */ /** * @} */ /** @defgroup SPI_Private_FunctionPrototypes * @{ */ /** * @} */ /** @defgroup SPI_Private_Functions * @{ */ /** * @brief Deinitializes the SPIx peripheral registers to their default * reset values (Affects also the I2Ss). * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @retval None */ void SPI_I2S_DeInit(SPI_TypeDef* SPIx) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); if (SPIx == SPI1) { /* Enable SPI1 reset state */ RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE); /* Release SPI1 from reset state */ RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE); } else if (SPIx == SPI2) { /* Enable SPI2 reset state */ RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE); /* Release SPI2 from reset state */ RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE); } else { if (SPIx == SPI3) { /* Enable SPI3 reset state */ RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE); /* Release SPI3 from reset state */ RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, DISABLE); } } } /** * @brief Initializes the SPIx peripheral according to the specified * parameters in the SPI_InitStruct. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param SPI_InitStruct: pointer to a SPI_InitTypeDef structure that * contains the configuration information for the specified SPI peripheral. * @retval None */ void SPI_Init(SPI_TypeDef* SPIx, SPI_InitTypeDef* SPI_InitStruct) { uint16_t tmpreg = 0; /* check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); /* Check the SPI parameters */ assert_param(IS_SPI_DIRECTION_MODE(SPI_InitStruct->SPI_Direction)); assert_param(IS_SPI_MODE(SPI_InitStruct->SPI_Mode)); assert_param(IS_SPI_DATASIZE(SPI_InitStruct->SPI_DataSize)); assert_param(IS_SPI_CPOL(SPI_InitStruct->SPI_CPOL)); assert_param(IS_SPI_CPHA(SPI_InitStruct->SPI_CPHA)); assert_param(IS_SPI_NSS(SPI_InitStruct->SPI_NSS)); assert_param(IS_SPI_BAUDRATE_PRESCALER(SPI_InitStruct->SPI_BaudRatePrescaler)); assert_param(IS_SPI_FIRST_BIT(SPI_InitStruct->SPI_FirstBit)); assert_param(IS_SPI_CRC_POLYNOMIAL(SPI_InitStruct->SPI_CRCPolynomial)); /*---------------------------- SPIx CR1 Configuration ------------------------*/ /* Get the SPIx CR1 value */ tmpreg = SPIx->CR1; /* Clear BIDIMode, BIDIOE, RxONLY, SSM, SSI, LSBFirst, BR, MSTR, CPOL and CPHA bits */ tmpreg &= CR1_CLEAR_Mask; /* Configure SPIx: direction, NSS management, first transmitted bit, BaudRate prescaler master/salve mode, CPOL and CPHA */ /* Set BIDImode, BIDIOE and RxONLY bits according to SPI_Direction value */ /* Set SSM, SSI and MSTR bits according to SPI_Mode and SPI_NSS values */ /* Set LSBFirst bit according to SPI_FirstBit value */ /* Set BR bits according to SPI_BaudRatePrescaler value */ /* Set CPOL bit according to SPI_CPOL value */ /* Set CPHA bit according to SPI_CPHA value */ tmpreg |= (uint16_t)((uint32_t)SPI_InitStruct->SPI_Direction | SPI_InitStruct->SPI_Mode | SPI_InitStruct->SPI_DataSize | SPI_InitStruct->SPI_CPOL | SPI_InitStruct->SPI_CPHA | SPI_InitStruct->SPI_NSS | SPI_InitStruct->SPI_BaudRatePrescaler | SPI_InitStruct->SPI_FirstBit); /* Write to SPIx CR1 */ SPIx->CR1 = tmpreg; /* Activate the SPI mode (Reset I2SMOD bit in I2SCFGR register) */ SPIx->I2SCFGR &= SPI_Mode_Select; /*---------------------------- SPIx CRCPOLY Configuration --------------------*/ /* Write to SPIx CRCPOLY */ SPIx->CRCPR = SPI_InitStruct->SPI_CRCPolynomial; } /** * @brief Initializes the SPIx peripheral according to the specified * parameters in the I2S_InitStruct. * @param SPIx: where x can be 2 or 3 to select the SPI peripheral * (configured in I2S mode). * @param I2S_InitStruct: pointer to an I2S_InitTypeDef structure that * contains the configuration information for the specified SPI peripheral * configured in I2S mode. * @note * The function calculates the optimal prescaler needed to obtain the most * accurate audio frequency (depending on the I2S clock source, the PLL values * and the product configuration). But in case the prescaler value is greater * than 511, the default value (0x02) will be configured instead. * * @retval None */ void I2S_Init(SPI_TypeDef* SPIx, I2S_InitTypeDef* I2S_InitStruct) { uint16_t tmpreg = 0, i2sdiv = 2, i2sodd = 0, packetlength = 1; uint32_t tmp = 0; RCC_ClocksTypeDef RCC_Clocks; uint32_t sourceclock = 0; /* Check the I2S parameters */ assert_param(IS_SPI_23_PERIPH(SPIx)); assert_param(IS_I2S_MODE(I2S_InitStruct->I2S_Mode)); assert_param(IS_I2S_STANDARD(I2S_InitStruct->I2S_Standard)); assert_param(IS_I2S_DATA_FORMAT(I2S_InitStruct->I2S_DataFormat)); assert_param(IS_I2S_MCLK_OUTPUT(I2S_InitStruct->I2S_MCLKOutput)); assert_param(IS_I2S_AUDIO_FREQ(I2S_InitStruct->I2S_AudioFreq)); assert_param(IS_I2S_CPOL(I2S_InitStruct->I2S_CPOL)); /*----------------------- SPIx I2SCFGR & I2SPR Configuration -----------------*/ /* Clear I2SMOD, I2SE, I2SCFG, PCMSYNC, I2SSTD, CKPOL, DATLEN and CHLEN bits */ SPIx->I2SCFGR &= I2SCFGR_CLEAR_Mask; SPIx->I2SPR = 0x0002; /* Get the I2SCFGR register value */ tmpreg = SPIx->I2SCFGR; /* If the default value has to be written, reinitialize i2sdiv and i2sodd*/ if(I2S_InitStruct->I2S_AudioFreq == I2S_AudioFreq_Default) { i2sodd = (uint16_t)0; i2sdiv = (uint16_t)2; } /* If the requested audio frequency is not the default, compute the prescaler */ else { /* Check the frame length (For the Prescaler computing) */ if(I2S_InitStruct->I2S_DataFormat == I2S_DataFormat_16b) { /* Packet length is 16 bits */ packetlength = 1; } else { /* Packet length is 32 bits */ packetlength = 2; } /* Get the I2S clock source mask depending on the peripheral number */ if(((uint32_t)SPIx) == SPI2_BASE) { /* The mask is relative to I2S2 */ tmp = I2S2_CLOCK_SRC; } else { /* The mask is relative to I2S3 */ tmp = I2S3_CLOCK_SRC; } /* Check the I2S clock source configuration depending on the Device: Only Connectivity line devices have the PLL3 VCO clock */ #ifdef STM32F10X_CL if((RCC->CFGR2 & tmp) != 0) { /* Get the configuration bits of RCC PLL3 multiplier */ tmp = (uint32_t)((RCC->CFGR2 & I2S_MUL_MASK) >> 12); /* Get the value of the PLL3 multiplier */ if((tmp > 5) && (tmp < 15)) { /* Multiplier is between 8 and 14 (value 15 is forbidden) */ tmp += 2; } else { if (tmp == 15) { /* Multiplier is 20 */ tmp = 20; } } /* Get the PREDIV2 value */ sourceclock = (uint32_t)(((RCC->CFGR2 & I2S_DIV_MASK) >> 4) + 1); /* Calculate the Source Clock frequency based on PLL3 and PREDIV2 values */ sourceclock = (uint32_t) ((HSE_Value / sourceclock) * tmp * 2); } else { /* I2S Clock source is System clock: Get System Clock frequency */ RCC_GetClocksFreq(&RCC_Clocks); /* Get the source clock value: based on System Clock value */ sourceclock = RCC_Clocks.SYSCLK_Frequency; } #else /* STM32F10X_HD */ /* I2S Clock source is System clock: Get System Clock frequency */ RCC_GetClocksFreq(&RCC_Clocks); /* Get the source clock value: based on System Clock value */ sourceclock = RCC_Clocks.SYSCLK_Frequency; #endif /* STM32F10X_CL */ /* Compute the Real divider depending on the MCLK output state with a floating point */ if(I2S_InitStruct->I2S_MCLKOutput == I2S_MCLKOutput_Enable) { /* MCLK output is enabled */ tmp = (uint16_t)(((((sourceclock / 256) * 10) / I2S_InitStruct->I2S_AudioFreq)) + 5); } else { /* MCLK output is disabled */ tmp = (uint16_t)(((((sourceclock / (32 * packetlength)) *10 ) / I2S_InitStruct->I2S_AudioFreq)) + 5); } /* Remove the floating point */ tmp = tmp / 10; /* Check the parity of the divider */ i2sodd = (uint16_t)(tmp & (uint16_t)0x0001); /* Compute the i2sdiv prescaler */ i2sdiv = (uint16_t)((tmp - i2sodd) / 2); /* Get the Mask for the Odd bit (SPI_I2SPR[8]) register */ i2sodd = (uint16_t) (i2sodd << 8); } /* Test if the divider is 1 or 0 or greater than 0xFF */ if ((i2sdiv < 2) || (i2sdiv > 0xFF)) { /* Set the default values */ i2sdiv = 2; i2sodd = 0; } /* Write to SPIx I2SPR register the computed value */ SPIx->I2SPR = (uint16_t)(i2sdiv | (uint16_t)(i2sodd | (uint16_t)I2S_InitStruct->I2S_MCLKOutput)); /* Configure the I2S with the SPI_InitStruct values */ tmpreg |= (uint16_t)(I2S_Mode_Select | (uint16_t)(I2S_InitStruct->I2S_Mode | \ (uint16_t)(I2S_InitStruct->I2S_Standard | (uint16_t)(I2S_InitStruct->I2S_DataFormat | \ (uint16_t)I2S_InitStruct->I2S_CPOL)))); /* Write to SPIx I2SCFGR */ SPIx->I2SCFGR = tmpreg; } /** * @brief Fills each SPI_InitStruct member with its default value. * @param SPI_InitStruct : pointer to a SPI_InitTypeDef structure which will be initialized. * @retval None */ void SPI_StructInit(SPI_InitTypeDef* SPI_InitStruct) { /*--------------- Reset SPI init structure parameters values -----------------*/ /* Initialize the SPI_Direction member */ SPI_InitStruct->SPI_Direction = SPI_Direction_2Lines_FullDuplex; /* initialize the SPI_Mode member */ SPI_InitStruct->SPI_Mode = SPI_Mode_Slave; /* initialize the SPI_DataSize member */ SPI_InitStruct->SPI_DataSize = SPI_DataSize_8b; /* Initialize the SPI_CPOL member */ SPI_InitStruct->SPI_CPOL = SPI_CPOL_Low; /* Initialize the SPI_CPHA member */ SPI_InitStruct->SPI_CPHA = SPI_CPHA_1Edge; /* Initialize the SPI_NSS member */ SPI_InitStruct->SPI_NSS = SPI_NSS_Hard; /* Initialize the SPI_BaudRatePrescaler member */ SPI_InitStruct->SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2; /* Initialize the SPI_FirstBit member */ SPI_InitStruct->SPI_FirstBit = SPI_FirstBit_MSB; /* Initialize the SPI_CRCPolynomial member */ SPI_InitStruct->SPI_CRCPolynomial = 7; } /** * @brief Fills each I2S_InitStruct member with its default value. * @param I2S_InitStruct : pointer to a I2S_InitTypeDef structure which will be initialized. * @retval None */ void I2S_StructInit(I2S_InitTypeDef* I2S_InitStruct) { /*--------------- Reset I2S init structure parameters values -----------------*/ /* Initialize the I2S_Mode member */ I2S_InitStruct->I2S_Mode = I2S_Mode_SlaveTx; /* Initialize the I2S_Standard member */ I2S_InitStruct->I2S_Standard = I2S_Standard_Phillips; /* Initialize the I2S_DataFormat member */ I2S_InitStruct->I2S_DataFormat = I2S_DataFormat_16b; /* Initialize the I2S_MCLKOutput member */ I2S_InitStruct->I2S_MCLKOutput = I2S_MCLKOutput_Disable; /* Initialize the I2S_AudioFreq member */ I2S_InitStruct->I2S_AudioFreq = I2S_AudioFreq_Default; /* Initialize the I2S_CPOL member */ I2S_InitStruct->I2S_CPOL = I2S_CPOL_Low; } /** * @brief Enables or disables the specified SPI peripheral. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param NewState: new state of the SPIx peripheral. * This parameter can be: ENABLE or DISABLE. * @retval None */ void SPI_Cmd(SPI_TypeDef* SPIx, FunctionalState NewState) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); if (NewState != DISABLE) { /* Enable the selected SPI peripheral */ SPIx->CR1 |= CR1_SPE_Set; } else { /* Disable the selected SPI peripheral */ SPIx->CR1 &= CR1_SPE_Reset; } } /** * @brief Enables or disables the specified SPI peripheral (in I2S mode). * @param SPIx: where x can be 2 or 3 to select the SPI peripheral. * @param NewState: new state of the SPIx peripheral. * This parameter can be: ENABLE or DISABLE. * @retval None */ void I2S_Cmd(SPI_TypeDef* SPIx, FunctionalState NewState) { /* Check the parameters */ assert_param(IS_SPI_23_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); if (NewState != DISABLE) { /* Enable the selected SPI peripheral (in I2S mode) */ SPIx->I2SCFGR |= I2SCFGR_I2SE_Set; } else { /* Disable the selected SPI peripheral (in I2S mode) */ SPIx->I2SCFGR &= I2SCFGR_I2SE_Reset; } } /** * @brief Enables or disables the specified SPI/I2S interrupts. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @param SPI_I2S_IT: specifies the SPI/I2S interrupt source to be enabled or disabled. * This parameter can be one of the following values: * @arg SPI_I2S_IT_TXE: Tx buffer empty interrupt mask * @arg SPI_I2S_IT_RXNE: Rx buffer not empty interrupt mask * @arg SPI_I2S_IT_ERR: Error interrupt mask * @param NewState: new state of the specified SPI/I2S interrupt. * This parameter can be: ENABLE or DISABLE. * @retval None */ void SPI_I2S_ITConfig(SPI_TypeDef* SPIx, uint8_t SPI_I2S_IT, FunctionalState NewState) { uint16_t itpos = 0, itmask = 0 ; /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); assert_param(IS_SPI_I2S_CONFIG_IT(SPI_I2S_IT)); /* Get the SPI/I2S IT index */ itpos = SPI_I2S_IT >> 4; /* Set the IT mask */ itmask = (uint16_t)1 << (uint16_t)itpos; if (NewState != DISABLE) { /* Enable the selected SPI/I2S interrupt */ SPIx->CR2 |= itmask; } else { /* Disable the selected SPI/I2S interrupt */ SPIx->CR2 &= (uint16_t)~itmask; } } /** * @brief Enables or disables the SPIx/I2Sx DMA interface. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @param SPI_I2S_DMAReq: specifies the SPI/I2S DMA transfer request to be enabled or disabled. * This parameter can be any combination of the following values: * @arg SPI_I2S_DMAReq_Tx: Tx buffer DMA transfer request * @arg SPI_I2S_DMAReq_Rx: Rx buffer DMA transfer request * @param NewState: new state of the selected SPI/I2S DMA transfer request. * This parameter can be: ENABLE or DISABLE. * @retval None */ void SPI_I2S_DMACmd(SPI_TypeDef* SPIx, uint16_t SPI_I2S_DMAReq, FunctionalState NewState) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); assert_param(IS_SPI_I2S_DMAREQ(SPI_I2S_DMAReq)); if (NewState != DISABLE) { /* Enable the selected SPI/I2S DMA requests */ SPIx->CR2 |= SPI_I2S_DMAReq; } else { /* Disable the selected SPI/I2S DMA requests */ SPIx->CR2 &= (uint16_t)~SPI_I2S_DMAReq; } } /** * @brief Transmits a Data through the SPIx/I2Sx peripheral. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @param Data : Data to be transmitted. * @retval None */ void SPI_I2S_SendData(SPI_TypeDef* SPIx, uint16_t Data) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); /* Write in the DR register the data to be sent */ SPIx->DR = Data; } /** * @brief Returns the most recent received data by the SPIx/I2Sx peripheral. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @retval The value of the received data. */ uint16_t SPI_I2S_ReceiveData(SPI_TypeDef* SPIx) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); /* Return the data in the DR register */ return SPIx->DR; } /** * @brief Configures internally by software the NSS pin for the selected SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param SPI_NSSInternalSoft: specifies the SPI NSS internal state. * This parameter can be one of the following values: * @arg SPI_NSSInternalSoft_Set: Set NSS pin internally * @arg SPI_NSSInternalSoft_Reset: Reset NSS pin internally * @retval None */ void SPI_NSSInternalSoftwareConfig(SPI_TypeDef* SPIx, uint16_t SPI_NSSInternalSoft) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_NSS_INTERNAL(SPI_NSSInternalSoft)); if (SPI_NSSInternalSoft != SPI_NSSInternalSoft_Reset) { /* Set NSS pin internally by software */ SPIx->CR1 |= SPI_NSSInternalSoft_Set; } else { /* Reset NSS pin internally by software */ SPIx->CR1 &= SPI_NSSInternalSoft_Reset; } } /** * @brief Enables or disables the SS output for the selected SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param NewState: new state of the SPIx SS output. * This parameter can be: ENABLE or DISABLE. * @retval None */ void SPI_SSOutputCmd(SPI_TypeDef* SPIx, FunctionalState NewState) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); if (NewState != DISABLE) { /* Enable the selected SPI SS output */ SPIx->CR2 |= CR2_SSOE_Set; } else { /* Disable the selected SPI SS output */ SPIx->CR2 &= CR2_SSOE_Reset; } } /** * @brief Configures the data size for the selected SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param SPI_DataSize: specifies the SPI data size. * This parameter can be one of the following values: * @arg SPI_DataSize_16b: Set data frame format to 16bit * @arg SPI_DataSize_8b: Set data frame format to 8bit * @retval None */ void SPI_DataSizeConfig(SPI_TypeDef* SPIx, uint16_t SPI_DataSize) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_DATASIZE(SPI_DataSize)); /* Clear DFF bit */ SPIx->CR1 &= (uint16_t)~SPI_DataSize_16b; /* Set new DFF bit value */ SPIx->CR1 |= SPI_DataSize; } /** * @brief Transmit the SPIx CRC value. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @retval None */ void SPI_TransmitCRC(SPI_TypeDef* SPIx) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); /* Enable the selected SPI CRC transmission */ SPIx->CR1 |= CR1_CRCNext_Set; } /** * @brief Enables or disables the CRC value calculation of the transferred bytes. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param NewState: new state of the SPIx CRC value calculation. * This parameter can be: ENABLE or DISABLE. * @retval None */ void SPI_CalculateCRC(SPI_TypeDef* SPIx, FunctionalState NewState) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_FUNCTIONAL_STATE(NewState)); if (NewState != DISABLE) { /* Enable the selected SPI CRC calculation */ SPIx->CR1 |= CR1_CRCEN_Set; } else { /* Disable the selected SPI CRC calculation */ SPIx->CR1 &= CR1_CRCEN_Reset; } } /** * @brief Returns the transmit or the receive CRC register value for the specified SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param SPI_CRC: specifies the CRC register to be read. * This parameter can be one of the following values: * @arg SPI_CRC_Tx: Selects Tx CRC register * @arg SPI_CRC_Rx: Selects Rx CRC register * @retval The selected CRC register value.. */ uint16_t SPI_GetCRC(SPI_TypeDef* SPIx, uint8_t SPI_CRC) { uint16_t crcreg = 0; /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_CRC(SPI_CRC)); if (SPI_CRC != SPI_CRC_Rx) { /* Get the Tx CRC register */ crcreg = SPIx->TXCRCR; } else { /* Get the Rx CRC register */ crcreg = SPIx->RXCRCR; } /* Return the selected CRC register */ return crcreg; } /** * @brief Returns the CRC Polynomial register value for the specified SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @retval The CRC Polynomial register value. */ uint16_t SPI_GetCRCPolynomial(SPI_TypeDef* SPIx) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); /* Return the CRC polynomial register */ return SPIx->CRCPR; } /** * @brief Selects the data transfer direction in bi-directional mode for the specified SPI. * @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral. * @param SPI_Direction: specifies the data transfer direction in bi-directional mode. * This parameter can be one of the following values: * @arg SPI_Direction_Tx: Selects Tx transmission direction * @arg SPI_Direction_Rx: Selects Rx receive direction * @retval None */ void SPI_BiDirectionalLineConfig(SPI_TypeDef* SPIx, uint16_t SPI_Direction) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_DIRECTION(SPI_Direction)); if (SPI_Direction == SPI_Direction_Tx) { /* Set the Tx only mode */ SPIx->CR1 |= SPI_Direction_Tx; } else { /* Set the Rx only mode */ SPIx->CR1 &= SPI_Direction_Rx; } } /** * @brief Checks whether the specified SPI/I2S flag is set or not. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @param SPI_I2S_FLAG: specifies the SPI/I2S flag to check. * This parameter can be one of the following values: * @arg SPI_I2S_FLAG_TXE: Transmit buffer empty flag. * @arg SPI_I2S_FLAG_RXNE: Receive buffer not empty flag. * @arg SPI_I2S_FLAG_BSY: Busy flag. * @arg SPI_I2S_FLAG_OVR: Overrun flag. * @arg SPI_FLAG_MODF: Mode Fault flag. * @arg SPI_FLAG_CRCERR: CRC Error flag. * @arg I2S_FLAG_UDR: Underrun Error flag. * @arg I2S_FLAG_CHSIDE: Channel Side flag. * @retval The new state of SPI_I2S_FLAG (SET or RESET). */ FlagStatus SPI_I2S_GetFlagStatus(SPI_TypeDef* SPIx, uint16_t SPI_I2S_FLAG) { FlagStatus bitstatus = RESET; /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_I2S_GET_FLAG(SPI_I2S_FLAG)); /* Check the status of the specified SPI/I2S flag */ if ((SPIx->SR & SPI_I2S_FLAG) != (uint16_t)RESET) { /* SPI_I2S_FLAG is set */ bitstatus = SET; } else { /* SPI_I2S_FLAG is reset */ bitstatus = RESET; } /* Return the SPI_I2S_FLAG status */ return bitstatus; } /** * @brief Clears the SPIx CRC Error (CRCERR) flag. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * @param SPI_I2S_FLAG: specifies the SPI flag to clear. * This function clears only CRCERR flag. * @note * - OVR (OverRun error) flag is cleared by software sequence: a read * operation to SPI_DR register (SPI_I2S_ReceiveData()) followed by a read * operation to SPI_SR register (SPI_I2S_GetFlagStatus()). * - UDR (UnderRun error) flag is cleared by a read operation to * SPI_SR register (SPI_I2S_GetFlagStatus()). * - MODF (Mode Fault) flag is cleared by software sequence: a read/write * operation to SPI_SR register (SPI_I2S_GetFlagStatus()) followed by a * write operation to SPI_CR1 register (SPI_Cmd() to enable the SPI). * @retval None */ void SPI_I2S_ClearFlag(SPI_TypeDef* SPIx, uint16_t SPI_I2S_FLAG) { /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_I2S_CLEAR_FLAG(SPI_I2S_FLAG)); /* Clear the selected SPI CRC Error (CRCERR) flag */ SPIx->SR = (uint16_t)~SPI_I2S_FLAG; } /** * @brief Checks whether the specified SPI/I2S interrupt has occurred or not. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * - 2 or 3 in I2S mode * @param SPI_I2S_IT: specifies the SPI/I2S interrupt source to check. * This parameter can be one of the following values: * @arg SPI_I2S_IT_TXE: Transmit buffer empty interrupt. * @arg SPI_I2S_IT_RXNE: Receive buffer not empty interrupt. * @arg SPI_I2S_IT_OVR: Overrun interrupt. * @arg SPI_IT_MODF: Mode Fault interrupt. * @arg SPI_IT_CRCERR: CRC Error interrupt. * @arg I2S_IT_UDR: Underrun Error interrupt. * @retval The new state of SPI_I2S_IT (SET or RESET). */ ITStatus SPI_I2S_GetITStatus(SPI_TypeDef* SPIx, uint8_t SPI_I2S_IT) { ITStatus bitstatus = RESET; uint16_t itpos = 0, itmask = 0, enablestatus = 0; /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_I2S_GET_IT(SPI_I2S_IT)); /* Get the SPI/I2S IT index */ itpos = 0x01 << (SPI_I2S_IT & 0x0F); /* Get the SPI/I2S IT mask */ itmask = SPI_I2S_IT >> 4; /* Set the IT mask */ itmask = 0x01 << itmask; /* Get the SPI_I2S_IT enable bit status */ enablestatus = (SPIx->CR2 & itmask) ; /* Check the status of the specified SPI/I2S interrupt */ if (((SPIx->SR & itpos) != (uint16_t)RESET) && enablestatus) { /* SPI_I2S_IT is set */ bitstatus = SET; } else { /* SPI_I2S_IT is reset */ bitstatus = RESET; } /* Return the SPI_I2S_IT status */ return bitstatus; } /** * @brief Clears the SPIx CRC Error (CRCERR) interrupt pending bit. * @param SPIx: where x can be * - 1, 2 or 3 in SPI mode * @param SPI_I2S_IT: specifies the SPI interrupt pending bit to clear. * This function clears only CRCERR interrupt pending bit. * @note * - OVR (OverRun Error) interrupt pending bit is cleared by software * sequence: a read operation to SPI_DR register (SPI_I2S_ReceiveData()) * followed by a read operation to SPI_SR register (SPI_I2S_GetITStatus()). * - UDR (UnderRun Error) interrupt pending bit is cleared by a read * operation to SPI_SR register (SPI_I2S_GetITStatus()). * - MODF (Mode Fault) interrupt pending bit is cleared by software sequence: * a read/write operation to SPI_SR register (SPI_I2S_GetITStatus()) * followed by a write operation to SPI_CR1 register (SPI_Cmd() to enable * the SPI). * @retval None */ void SPI_I2S_ClearITPendingBit(SPI_TypeDef* SPIx, uint8_t SPI_I2S_IT) { uint16_t itpos = 0; /* Check the parameters */ assert_param(IS_SPI_ALL_PERIPH(SPIx)); assert_param(IS_SPI_I2S_CLEAR_IT(SPI_I2S_IT)); /* Get the SPI IT index */ itpos = 0x01 << (SPI_I2S_IT & 0x0F); /* Clear the selected SPI CRC Error (CRCERR) interrupt pending bit */ SPIx->SR = (uint16_t)~itpos; } /** * @} */ /** * @} */ /** * @} */ /******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/