mbed library sources
Fork of mbed-src by
targets/cmsis/TARGET_NXP/TARGET_LPC176X/system_LPC17xx.c
- Committer:
- todotani
- Date:
- 2014-09-05
- Revision:
- 308:59cc78a25982
- Parent:
- 13:0645d8841f51
File content as of revision 308:59cc78a25982:
/**************************************************************************//** * @file system_LPC17xx.c * @brief CMSIS Cortex-M3 Device System Source File for * NXP LPC17xx Device Series * @version V1.11 * @date 21. June 2011 * * @note * Copyright (C) 2009-2011 ARM Limited. All rights reserved. * * @par * ARM Limited (ARM) is supplying this software for use with Cortex-M * processor based microcontrollers. This file can be freely distributed * within development tools that are supporting such ARM based processors. * * @par * THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED * OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. * ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR * CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. * ******************************************************************************/ #include <stdint.h> #include "LPC17xx.h" /** @addtogroup LPC17xx_System * @{ */ /* //-------- <<< Use Configuration Wizard in Context Menu >>> ------------------ */ /*--------------------- Clock Configuration ---------------------------------- // // <e> Clock Configuration // <h> System Controls and Status Register (SCS) // <o1.4> OSCRANGE: Main Oscillator Range Select // <0=> 1 MHz to 20 MHz // <1=> 15 MHz to 25 MHz // <e1.5> OSCEN: Main Oscillator Enable // </e> // </h> // // <h> Clock Source Select Register (CLKSRCSEL) // <o2.0..1> CLKSRC: PLL Clock Source Selection // <0=> Internal RC oscillator // <1=> Main oscillator // <2=> RTC oscillator // </h> // // <e3> PLL0 Configuration (Main PLL) // <h> PLL0 Configuration Register (PLL0CFG) // <i> F_cco0 = (2 * M * F_in) / N // <i> F_in must be in the range of 32 kHz to 50 MHz // <i> F_cco0 must be in the range of 275 MHz to 550 MHz // <o4.0..14> MSEL: PLL Multiplier Selection // <6-32768><#-1> // <i> M Value // <o4.16..23> NSEL: PLL Divider Selection // <1-256><#-1> // <i> N Value // </h> // </e> // // <e5> PLL1 Configuration (USB PLL) // <h> PLL1 Configuration Register (PLL1CFG) // <i> F_usb = M * F_osc or F_usb = F_cco1 / (2 * P) // <i> F_cco1 = F_osc * M * 2 * P // <i> F_cco1 must be in the range of 156 MHz to 320 MHz // <o6.0..4> MSEL: PLL Multiplier Selection // <1-32><#-1> // <i> M Value (for USB maximum value is 4) // <o6.5..6> PSEL: PLL Divider Selection // <0=> 1 // <1=> 2 // <2=> 4 // <3=> 8 // <i> P Value // </h> // </e> // // <h> CPU Clock Configuration Register (CCLKCFG) // <o7.0..7> CCLKSEL: Divide Value for CPU Clock from PLL0 // <1-256><#-1> // </h> // // <h> USB Clock Configuration Register (USBCLKCFG) // <o8.0..3> USBSEL: Divide Value for USB Clock from PLL0 // <0-15> // <i> Divide is USBSEL + 1 // </h> // // <h> Peripheral Clock Selection Register 0 (PCLKSEL0) // <o9.0..1> PCLK_WDT: Peripheral Clock Selection for WDT // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.2..3> PCLK_TIMER0: Peripheral Clock Selection for TIMER0 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.4..5> PCLK_TIMER1: Peripheral Clock Selection for TIMER1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.6..7> PCLK_UART0: Peripheral Clock Selection for UART0 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.8..9> PCLK_UART1: Peripheral Clock Selection for UART1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.12..13> PCLK_PWM1: Peripheral Clock Selection for PWM1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.14..15> PCLK_I2C0: Peripheral Clock Selection for I2C0 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.16..17> PCLK_SPI: Peripheral Clock Selection for SPI // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.20..21> PCLK_SSP1: Peripheral Clock Selection for SSP1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.22..23> PCLK_DAC: Peripheral Clock Selection for DAC // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.24..25> PCLK_ADC: Peripheral Clock Selection for ADC // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o9.26..27> PCLK_CAN1: Peripheral Clock Selection for CAN1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 6 // <o9.28..29> PCLK_CAN2: Peripheral Clock Selection for CAN2 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 6 // <o9.30..31> PCLK_ACF: Peripheral Clock Selection for ACF // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 6 // </h> // // <h> Peripheral Clock Selection Register 1 (PCLKSEL1) // <o10.0..1> PCLK_QEI: Peripheral Clock Selection for the Quadrature Encoder Interface // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.2..3> PCLK_GPIO: Peripheral Clock Selection for GPIOs // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.4..5> PCLK_PCB: Peripheral Clock Selection for the Pin Connect Block // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.6..7> PCLK_I2C1: Peripheral Clock Selection for I2C1 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.10..11> PCLK_SSP0: Peripheral Clock Selection for SSP0 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.12..13> PCLK_TIMER2: Peripheral Clock Selection for TIMER2 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.14..15> PCLK_TIMER3: Peripheral Clock Selection for TIMER3 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.16..17> PCLK_UART2: Peripheral Clock Selection for UART2 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.18..19> PCLK_UART3: Peripheral Clock Selection for UART3 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.20..21> PCLK_I2C2: Peripheral Clock Selection for I2C2 // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.22..23> PCLK_I2S: Peripheral Clock Selection for I2S // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.26..27> PCLK_RIT: Peripheral Clock Selection for the Repetitive Interrupt Timer // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.28..29> PCLK_SYSCON: Peripheral Clock Selection for the System Control Block // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // <o10.30..31> PCLK_MC: Peripheral Clock Selection for the Motor Control PWM // <0=> Pclk = Cclk / 4 // <1=> Pclk = Cclk // <2=> Pclk = Cclk / 2 // <3=> Pclk = Hclk / 8 // </h> // // <h> Power Control for Peripherals Register (PCONP) // <o11.1> PCTIM0: Timer/Counter 0 power/clock enable // <o11.2> PCTIM1: Timer/Counter 1 power/clock enable // <o11.3> PCUART0: UART 0 power/clock enable // <o11.4> PCUART1: UART 1 power/clock enable // <o11.6> PCPWM1: PWM 1 power/clock enable // <o11.7> PCI2C0: I2C interface 0 power/clock enable // <o11.8> PCSPI: SPI interface power/clock enable // <o11.9> PCRTC: RTC power/clock enable // <o11.10> PCSSP1: SSP interface 1 power/clock enable // <o11.12> PCAD: A/D converter power/clock enable // <o11.13> PCCAN1: CAN controller 1 power/clock enable // <o11.14> PCCAN2: CAN controller 2 power/clock enable // <o11.15> PCGPIO: GPIOs power/clock enable // <o11.16> PCRIT: Repetitive interrupt timer power/clock enable // <o11.17> PCMC: Motor control PWM power/clock enable // <o11.18> PCQEI: Quadrature encoder interface power/clock enable // <o11.19> PCI2C1: I2C interface 1 power/clock enable // <o11.21> PCSSP0: SSP interface 0 power/clock enable // <o11.22> PCTIM2: Timer 2 power/clock enable // <o11.23> PCTIM3: Timer 3 power/clock enable // <o11.24> PCUART2: UART 2 power/clock enable // <o11.25> PCUART3: UART 3 power/clock enable // <o11.26> PCI2C2: I2C interface 2 power/clock enable // <o11.27> PCI2S: I2S interface power/clock enable // <o11.29> PCGPDMA: GP DMA function power/clock enable // <o11.30> PCENET: Ethernet block power/clock enable // <o11.31> PCUSB: USB interface power/clock enable // </h> // // <h> Clock Output Configuration Register (CLKOUTCFG) // <o12.0..3> CLKOUTSEL: Selects clock source for CLKOUT // <0=> CPU clock // <1=> Main oscillator // <2=> Internal RC oscillator // <3=> USB clock // <4=> RTC oscillator // <o12.4..7> CLKOUTDIV: Selects clock divider for CLKOUT // <1-16><#-1> // <o12.8> CLKOUT_EN: CLKOUT enable control // </h> // // </e> */ /** @addtogroup LPC17xx_System_Defines LPC17xx System Defines @{ */ #define CLOCK_SETUP 1 #define SCS_Val 0x00000020 #define CLKSRCSEL_Val 0x00000001 #define PLL0_SETUP 1 #ifdef MCB1700 # define PLL0CFG_Val 0x00050063 # define PLL1_SETUP 1 # define PLL1CFG_Val 0x00000023 # define CCLKCFG_Val 0x00000003 # define USBCLKCFG_Val 0x00000000 #else # define PLL0CFG_Val 0x0000000B # define PLL1_SETUP 0 # define PLL1CFG_Val 0x00000000 # define CCLKCFG_Val 0x00000002 # define USBCLKCFG_Val 0x00000005 #endif #define PCLKSEL0_Val 0x00000000 #define PCLKSEL1_Val 0x00000000 #define PCONP_Val 0x042887DE #define CLKOUTCFG_Val 0x00000000 /*--------------------- Flash Accelerator Configuration ---------------------- // // <e> Flash Accelerator Configuration // <o1.12..15> FLASHTIM: Flash Access Time // <0=> 1 CPU clock (for CPU clock up to 20 MHz) // <1=> 2 CPU clocks (for CPU clock up to 40 MHz) // <2=> 3 CPU clocks (for CPU clock up to 60 MHz) // <3=> 4 CPU clocks (for CPU clock up to 80 MHz) // <4=> 5 CPU clocks (for CPU clock up to 100 MHz) // <5=> 6 CPU clocks (for any CPU clock) // </e> */ #define FLASH_SETUP 1 #define FLASHCFG_Val 0x0000303A /* //-------- <<< end of configuration section >>> ------------------------------ */ /*---------------------------------------------------------------------------- Check the register settings *----------------------------------------------------------------------------*/ #define CHECK_RANGE(val, min, max) ((val < min) || (val > max)) #define CHECK_RSVD(val, mask) (val & mask) /* Clock Configuration -------------------------------------------------------*/ #if (CHECK_RSVD((SCS_Val), ~0x00000030)) #error "SCS: Invalid values of reserved bits!" #endif #if (CHECK_RANGE((CLKSRCSEL_Val), 0, 2)) #error "CLKSRCSEL: Value out of range!" #endif #if (CHECK_RSVD((PLL0CFG_Val), ~0x00FF7FFF)) #error "PLL0CFG: Invalid values of reserved bits!" #endif #if (CHECK_RSVD((PLL1CFG_Val), ~0x0000007F)) #error "PLL1CFG: Invalid values of reserved bits!" #endif #if (PLL0_SETUP) /* if PLL0 is used */ #if (CCLKCFG_Val < 2) /* CCLKSEL must be greater then 1 */ #error "CCLKCFG: CCLKSEL must be greater then 1 if PLL0 is used!" #endif #endif #if (CHECK_RANGE((CCLKCFG_Val), 2, 255)) #error "CCLKCFG: Value out of range!" #endif #if (CHECK_RSVD((USBCLKCFG_Val), ~0x0000000F)) #error "USBCLKCFG: Invalid values of reserved bits!" #endif #if (CHECK_RSVD((PCLKSEL0_Val), 0x000C0C00)) #error "PCLKSEL0: Invalid values of reserved bits!" #endif #if (CHECK_RSVD((PCLKSEL1_Val), 0x03000300)) #error "PCLKSEL1: Invalid values of reserved bits!" #endif #if (CHECK_RSVD((PCONP_Val), 0x10100821)) #error "PCONP: Invalid values of reserved bits!" #endif #if (CHECK_RSVD((CLKOUTCFG_Val), ~0x000001FF)) #error "CLKOUTCFG: Invalid values of reserved bits!" #endif /* Flash Accelerator Configuration -------------------------------------------*/ #if (CHECK_RSVD((FLASHCFG_Val), ~0x0000F07F)) #error "FLASHCFG: Invalid values of reserved bits!" #endif /*---------------------------------------------------------------------------- DEFINES *----------------------------------------------------------------------------*/ /*---------------------------------------------------------------------------- Define clocks *----------------------------------------------------------------------------*/ #define XTAL (12000000UL) /* Oscillator frequency */ #define OSC_CLK ( XTAL) /* Main oscillator frequency */ #define RTC_CLK ( 32000UL) /* RTC oscillator frequency */ #define IRC_OSC ( 4000000UL) /* Internal RC oscillator frequency */ /* F_cco0 = (2 * M * F_in) / N */ #define __M (((PLL0CFG_Val ) & 0x7FFF) + 1) #define __N (((PLL0CFG_Val >> 16) & 0x00FF) + 1) #define __FCCO(__F_IN) ((2ULL * __M * __F_IN) / __N) #define __CCLK_DIV (((CCLKCFG_Val ) & 0x00FF) + 1) /* Determine core clock frequency according to settings */ #if (PLL0_SETUP) #if ((CLKSRCSEL_Val & 0x03) == 1) #define __CORE_CLK (__FCCO(OSC_CLK) / __CCLK_DIV) #elif ((CLKSRCSEL_Val & 0x03) == 2) #define __CORE_CLK (__FCCO(RTC_CLK) / __CCLK_DIV) #else #define __CORE_CLK (__FCCO(IRC_OSC) / __CCLK_DIV) #endif #else #if ((CLKSRCSEL_Val & 0x03) == 1) #define __CORE_CLK (OSC_CLK / __CCLK_DIV) #elif ((CLKSRCSEL_Val & 0x03) == 2) #define __CORE_CLK (RTC_CLK / __CCLK_DIV) #else #define __CORE_CLK (IRC_OSC / __CCLK_DIV) #endif #endif /** * @} */ /** @addtogroup LPC17xx_System_Public_Variables LPC17xx System Public Variables @{ */ /*---------------------------------------------------------------------------- Clock Variable definitions *----------------------------------------------------------------------------*/ uint32_t SystemCoreClock = __CORE_CLK;/*!< System Clock Frequency (Core Clock)*/ /** * @} */ /** @addtogroup LPC17xx_System_Public_Functions LPC17xx System Public Functions @{ */ /** * Update SystemCoreClock variable * * @param none * @return none * * @brief Updates the SystemCoreClock with current core Clock * retrieved from cpu registers. */void SystemCoreClockUpdate (void) /* Get Core Clock Frequency */ { /* Determine clock frequency according to clock register values */ if (((LPC_SC->PLL0STAT >> 24) & 3) == 3) { /* If PLL0 enabled and connected */ switch (LPC_SC->CLKSRCSEL & 0x03) { case 0: /* Int. RC oscillator => PLL0 */ case 3: /* Reserved, default to Int. RC */ SystemCoreClock = (IRC_OSC * ((2ULL * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) / (((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) / ((LPC_SC->CCLKCFG & 0xFF)+ 1)); break; case 1: /* Main oscillator => PLL0 */ SystemCoreClock = (OSC_CLK * ((2ULL * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) / (((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) / ((LPC_SC->CCLKCFG & 0xFF)+ 1)); break; case 2: /* RTC oscillator => PLL0 */ SystemCoreClock = (RTC_CLK * ((2ULL * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) / (((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) / ((LPC_SC->CCLKCFG & 0xFF)+ 1)); break; } } else { switch (LPC_SC->CLKSRCSEL & 0x03) { case 0: /* Int. RC oscillator => PLL0 */ case 3: /* Reserved, default to Int. RC */ SystemCoreClock = IRC_OSC / ((LPC_SC->CCLKCFG & 0xFF)+ 1); break; case 1: /* Main oscillator => PLL0 */ SystemCoreClock = OSC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1); break; case 2: /* RTC oscillator => PLL0 */ SystemCoreClock = RTC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1); break; } } } /** * Initialize the system * * @param none * @return none * * @brief Setup the microcontroller system. * Initialize the System. */ void SystemInit (void) { #if (CLOCK_SETUP) /* Clock Setup */ LPC_SC->SCS = SCS_Val; if (LPC_SC->SCS & (1 << 5)) { /* If Main Oscillator is enabled */ while ((LPC_SC->SCS & (1<<6)) == 0);/* Wait for Oscillator to be ready */ } LPC_SC->CCLKCFG = CCLKCFG_Val; /* Setup Clock Divider */ /* Periphral clock must be selected before PLL0 enabling and connecting * - according errata.lpc1768-16.March.2010 - */ LPC_SC->PCLKSEL0 = PCLKSEL0_Val; /* Peripheral Clock Selection */ LPC_SC->PCLKSEL1 = PCLKSEL1_Val; #if (PLL0_SETUP) LPC_SC->CLKSRCSEL = CLKSRCSEL_Val; /* Select Clock Source for PLL0 */ LPC_SC->PLL0CFG = PLL0CFG_Val; /* configure PLL0 */ LPC_SC->PLL0FEED = 0xAA; LPC_SC->PLL0FEED = 0x55; LPC_SC->PLL0CON = 0x01; /* PLL0 Enable */ LPC_SC->PLL0FEED = 0xAA; LPC_SC->PLL0FEED = 0x55; while (!(LPC_SC->PLL0STAT & (1<<26)));/* Wait for PLOCK0 */ LPC_SC->PLL0CON = 0x03; /* PLL0 Enable & Connect */ LPC_SC->PLL0FEED = 0xAA; LPC_SC->PLL0FEED = 0x55; while (!(LPC_SC->PLL0STAT & ((1<<25) | (1<<24))));/* Wait for PLLC0_STAT & PLLE0_STAT */ #endif #if (PLL1_SETUP) LPC_SC->PLL1CFG = PLL1CFG_Val; LPC_SC->PLL1FEED = 0xAA; LPC_SC->PLL1FEED = 0x55; LPC_SC->PLL1CON = 0x01; /* PLL1 Enable */ LPC_SC->PLL1FEED = 0xAA; LPC_SC->PLL1FEED = 0x55; while (!(LPC_SC->PLL1STAT & (1<<10)));/* Wait for PLOCK1 */ LPC_SC->PLL1CON = 0x03; /* PLL1 Enable & Connect */ LPC_SC->PLL1FEED = 0xAA; LPC_SC->PLL1FEED = 0x55; while (!(LPC_SC->PLL1STAT & ((1<< 9) | (1<< 8))));/* Wait for PLLC1_STAT & PLLE1_STAT */ #else LPC_SC->USBCLKCFG = USBCLKCFG_Val; /* Setup USB Clock Divider */ #endif LPC_SC->PCONP = PCONP_Val; /* Power Control for Peripherals */ LPC_SC->CLKOUTCFG = CLKOUTCFG_Val; /* Clock Output Configuration */ #endif #if (FLASH_SETUP == 1) /* Flash Accelerator Setup */ LPC_SC->FLASHCFG = (LPC_SC->FLASHCFG & ~0x0000F000) | FLASHCFG_Val; #endif } /** * @} */ /** * @} */