mbed library sources
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_usart.c
- Revision:
- 76:aeb1df146756
- Child:
- 80:66393a7b209d
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_usart.c Mon Jan 27 14:30:07 2014 +0000 @@ -0,0 +1,1459 @@ +/** + ****************************************************************************** + * @file stm32l1xx_usart.c + * @author MCD Application Team + * @version V1.2.0 + * @date 22-February-2013 + * @brief This file provides firmware functions to manage the following + * functionalities of the Universal synchronous asynchronous receiver + * transmitter (USART): + * + Initialization and Configuration + * + Data transfers + * + Multi-Processor Communication + * + LIN mode + * + Half-duplex mode + * + Smartcard mode + * + IrDA mode + * + DMA transfers management + * + Interrupts and flags management + * + * @verbatim + =============================================================================== + ##### How to use this driver ##### + =============================================================================== + [..] + (#) Enable peripheral clock using + RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE) function for + USART1 or using RCC_APB1PeriphClockCmd(RCC_APB1Periph_USARTx, ENABLE) + function for USART2 and USART3. + (#) According to the USART mode, enable the GPIO clocks using + RCC_AHBPeriphClockCmd() function. (The I/O can be TX, RX, CTS, + or and SCLK). + (#) Peripheral's alternate function: + (++) Connect the pin to the desired peripherals' Alternate + Function (AF) using GPIO_PinAFConfig() function. + (++) Configure the desired pin in alternate function by: + GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF. + (++) Select the type, pull-up/pull-down and output speed via + GPIO_PuPd, GPIO_OType and GPIO_Speed members. + (++) Call GPIO_Init() function. + (#) Program the Baud Rate, Word Length , Stop Bit, Parity, Hardware + flow control and Mode(Receiver/Transmitter) using the SPI_Init() + function. + (#) For synchronous mode, enable the clock and program the polarity, + phase and last bit using the USART_ClockInit() function. + (#) Enable the NVIC and the corresponding interrupt using the function + USART_ITConfig() if you need to use interrupt mode. + (#) When using the DMA mode. + (++) Configure the DMA using DMA_Init() function. + (++) Active the needed channel Request using USART_DMACmd() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Enable the DMA using the DMA_Cmd() function, when using DMA mode. + [..] + Refer to Multi-Processor, LIN, half-duplex, Smartcard, IrDA sub-sections + for more details. + +@endverbatim + + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l1xx_usart.h" +#include "stm32l1xx_rcc.h" + +/** @addtogroup STM32L1xx_StdPeriph_Driver + * @{ + */ + +/** @defgroup USART + * @brief USART driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ + +/*!< USART CR1 register clear Mask ((~(uint16_t)0xE9F3)) */ +#define CR1_CLEAR_MASK ((uint16_t)(USART_CR1_M | USART_CR1_PCE | \ + USART_CR1_PS | USART_CR1_TE | \ + USART_CR1_RE)) + +/*!< USART CR2 register clock bits clear Mask ((~(uint16_t)0xF0FF)) */ +#define CR2_CLOCK_CLEAR_MASK ((uint16_t)(USART_CR2_CLKEN | USART_CR2_CPOL | \ + USART_CR2_CPHA | USART_CR2_LBCL)) + +/*!< USART CR3 register clear Mask ((~(uint16_t)0xFCFF)) */ +#define CR3_CLEAR_MASK ((uint16_t)(USART_CR3_RTSE | USART_CR3_CTSE)) + +/*!< USART Interrupts mask */ +#define IT_MASK ((uint16_t)0x001F) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup USART_Private_Functions + * @{ + */ + +/** @defgroup USART_Group1 Initialization and Configuration functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USART + in asynchronous and in synchronous modes. + (+) For the asynchronous mode only these parameters can be configured: + (+) Baud Rate. + (+) Word Length. + (+) Stop Bit. + (+) Parity: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + the possible USART frame formats are as listed in the following table: + [..] + +-------------------------------------------------------------+ + | M bit | PCE bit | USART frame | + |---------------------|---------------------------------------| + | 0 | 0 | | SB | 8 bit data | STB | | + |---------|-----------|---------------------------------------| + | 0 | 1 | | SB | 7 bit data | PB | STB | | + |---------|-----------|---------------------------------------| + | 1 | 0 | | SB | 9 bit data | STB | | + |---------|-----------|---------------------------------------| + | 1 | 1 | | SB | 8 bit data | PB | STB | | + +-------------------------------------------------------------+ + [..] + (+) Hardware flow control. + (+) Receiver/transmitter modes. + [..] The USART_Init() function follows the USART asynchronous configuration + procedure(details for the procedure are available in reference manual + (RM0038)). + (+) For the synchronous mode in addition to the asynchronous mode parameters + these parameters should be also configured: + (++) USART Clock Enabled. + (++) USART polarity. + (++) USART phase. + (++) USART LastBit. + [..] These parameters can be configured using the USART_ClockInit() function. + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the USARTx peripheral registers to their default reset values. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: USART1, USART2, USART3, + * UART4 or UART5. + * @retval None. + */ +void USART_DeInit(USART_TypeDef* USARTx) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + + if (USARTx == USART1) + { + RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, ENABLE); + RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, DISABLE); + } + else if (USARTx == USART2) + { + RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, DISABLE); + } + else if (USARTx == USART3) + { + RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, DISABLE); + } + else if (USARTx == UART4) + { + RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, DISABLE); + } + else + { + if (USARTx == UART5) + { + RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, DISABLE); + } + } +} + +/** + * @brief Initializes the USARTx peripheral according to the specified + * parameters in the USART_InitStruct. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: USART1, USART2, USART3, + * UART4 or UART5. + * @param USART_InitStruct: pointer to a USART_InitTypeDef structure that + * contains the configuration information for the specified USART peripheral. + * @retval None. + */ +void USART_Init(USART_TypeDef* USARTx, USART_InitTypeDef* USART_InitStruct) +{ + uint32_t tmpreg = 0x00, apbclock = 0x00; + uint32_t integerdivider = 0x00; + uint32_t fractionaldivider = 0x00; + RCC_ClocksTypeDef RCC_ClocksStatus; + + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_BAUDRATE(USART_InitStruct->USART_BaudRate)); + assert_param(IS_USART_WORD_LENGTH(USART_InitStruct->USART_WordLength)); + assert_param(IS_USART_STOPBITS(USART_InitStruct->USART_StopBits)); + assert_param(IS_USART_PARITY(USART_InitStruct->USART_Parity)); + assert_param(IS_USART_MODE(USART_InitStruct->USART_Mode)); + assert_param(IS_USART_HARDWARE_FLOW_CONTROL(USART_InitStruct->USART_HardwareFlowControl)); + + /* The hardware flow control is available only for USART1, USART2 and USART3 */ + if (USART_InitStruct->USART_HardwareFlowControl != USART_HardwareFlowControl_None) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + +/*---------------------------- USART CR2 Configuration -----------------------*/ + tmpreg = USARTx->CR2; + /* Clear STOP[13:12] bits */ + tmpreg &= (uint32_t)~((uint32_t)USART_CR2_STOP); + + /* Configure the USART Stop Bits, Clock, CPOL, CPHA and LastBit ------------*/ + /* Set STOP[13:12] bits according to USART_StopBits value */ + tmpreg |= (uint32_t)USART_InitStruct->USART_StopBits; + + /* Write to USART CR2 */ + USARTx->CR2 = (uint16_t)tmpreg; + +/*---------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = USARTx->CR1; + /* Clear M, PCE, PS, TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)CR1_CLEAR_MASK); + + /* Configure the USART Word Length, Parity and mode ----------------------- */ + /* Set the M bits according to USART_WordLength value */ + /* Set PCE and PS bits according to USART_Parity value */ + /* Set TE and RE bits according to USART_Mode value */ + tmpreg |= (uint32_t)USART_InitStruct->USART_WordLength | USART_InitStruct->USART_Parity | + USART_InitStruct->USART_Mode; + + /* Write to USART CR1 */ + USARTx->CR1 = (uint16_t)tmpreg; + +/*---------------------------- USART CR3 Configuration -----------------------*/ + tmpreg = USARTx->CR3; + /* Clear CTSE and RTSE bits */ + tmpreg &= (uint32_t)~((uint32_t)CR3_CLEAR_MASK); + + /* Configure the USART HFC -------------------------------------------------*/ + /* Set CTSE and RTSE bits according to USART_HardwareFlowControl value */ + tmpreg |= USART_InitStruct->USART_HardwareFlowControl; + + /* Write to USART CR3 */ + USARTx->CR3 = (uint16_t)tmpreg; + +/*---------------------------- USART BRR Configuration -----------------------*/ + /* Configure the USART Baud Rate -------------------------------------------*/ + RCC_GetClocksFreq(&RCC_ClocksStatus); + if (USARTx == USART1) + { + apbclock = RCC_ClocksStatus.PCLK2_Frequency; + } + else + { + apbclock = RCC_ClocksStatus.PCLK1_Frequency; + } + + /* Determine the integer part */ + if ((USARTx->CR1 & USART_CR1_OVER8) != 0) + { + /* Integer part computing in case Oversampling mode is 8 Samples */ + integerdivider = ((25 * apbclock) / (2 * (USART_InitStruct->USART_BaudRate))); + } + else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */ + { + /* Integer part computing in case Oversampling mode is 16 Samples */ + integerdivider = ((25 * apbclock) / (4 * (USART_InitStruct->USART_BaudRate))); + } + tmpreg = (integerdivider / 100) << 4; + + /* Determine the fractional part */ + fractionaldivider = integerdivider - (100 * (tmpreg >> 4)); + + /* Implement the fractional part in the register */ + if ((USARTx->CR1 & USART_CR1_OVER8) != 0) + { + tmpreg |= ((((fractionaldivider * 8) + 50) / 100)) & ((uint8_t)0x07); + } + else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */ + { + tmpreg |= ((((fractionaldivider * 16) + 50) / 100)) & ((uint8_t)0x0F); + } + + /* Write to USART BRR */ + USARTx->BRR = (uint16_t)tmpreg; +} + +/** + * @brief Fills each USART_InitStruct member with its default value. + * @param USART_InitStruct: pointer to a USART_InitTypeDef structure + * which will be initialized. + * @retval None + */ +void USART_StructInit(USART_InitTypeDef* USART_InitStruct) +{ + /* USART_InitStruct members default value */ + USART_InitStruct->USART_BaudRate = 9600; + USART_InitStruct->USART_WordLength = USART_WordLength_8b; + USART_InitStruct->USART_StopBits = USART_StopBits_1; + USART_InitStruct->USART_Parity = USART_Parity_No ; + USART_InitStruct->USART_Mode = USART_Mode_Rx | USART_Mode_Tx; + USART_InitStruct->USART_HardwareFlowControl = USART_HardwareFlowControl_None; +} + +/** + * @brief Initializes the USARTx peripheral Clock according to the + * specified parameters in the USART_ClockInitStruct. + * @param USARTx: where x can be 1, 2, 3 to select the USART peripheral. + * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef + * structure that contains the configuration information for the specified + * USART peripheral. + * @note The Smart Card and Synchronous modes are not available for UART4 and UART5. + * @retval None. + */ +void USART_ClockInit(USART_TypeDef* USARTx, USART_ClockInitTypeDef* USART_ClockInitStruct) +{ + uint32_t tmpreg = 0x00; + /* Check the parameters */ + assert_param(IS_USART_123_PERIPH(USARTx)); + assert_param(IS_USART_CLOCK(USART_ClockInitStruct->USART_Clock)); + assert_param(IS_USART_CPOL(USART_ClockInitStruct->USART_CPOL)); + assert_param(IS_USART_CPHA(USART_ClockInitStruct->USART_CPHA)); + assert_param(IS_USART_LASTBIT(USART_ClockInitStruct->USART_LastBit)); + +/*---------------------------- USART CR2 Configuration -----------------------*/ + tmpreg = USARTx->CR2; + /* Clear CLKEN, CPOL, CPHA and LBCL bits */ + tmpreg &= (uint32_t)~((uint32_t)CR2_CLOCK_CLEAR_MASK); + /* Configure the USART Clock, CPOL, CPHA and LastBit ------------*/ + /* Set CLKEN bit according to USART_Clock value */ + /* Set CPOL bit according to USART_CPOL value */ + /* Set CPHA bit according to USART_CPHA value */ + /* Set LBCL bit according to USART_LastBit value */ + tmpreg |= (uint32_t)USART_ClockInitStruct->USART_Clock | USART_ClockInitStruct->USART_CPOL | + USART_ClockInitStruct->USART_CPHA | USART_ClockInitStruct->USART_LastBit; + /* Write to USART CR2 */ + USARTx->CR2 = (uint16_t)tmpreg; +} + +/** + * @brief Fills each USART_ClockInitStruct member with its default value. + * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef + * structure which will be initialized. + * @retval None + */ +void USART_ClockStructInit(USART_ClockInitTypeDef* USART_ClockInitStruct) +{ + /* USART_ClockInitStruct members default value */ + USART_ClockInitStruct->USART_Clock = USART_Clock_Disable; + USART_ClockInitStruct->USART_CPOL = USART_CPOL_Low; + USART_ClockInitStruct->USART_CPHA = USART_CPHA_1Edge; + USART_ClockInitStruct->USART_LastBit = USART_LastBit_Disable; +} + +/** + * @brief Enables or disables the specified USART peripheral. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USARTx peripheral. + * This parameter can be: ENABLE or DISABLE. + * @retval None. + */ +void USART_Cmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the selected USART by setting the UE bit in the CR1 register */ + USARTx->CR1 |= USART_CR1_UE; + } + else + { + /* Disable the selected USART by clearing the UE bit in the CR1 register */ + USARTx->CR1 &= (uint16_t)~((uint16_t)USART_CR1_UE); + } +} + +/** + * @brief Sets the system clock prescaler. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_Prescaler: specifies the prescaler clock. + * @note The function is used for IrDA mode with UART4 and UART5. + * @retval None. + */ +void USART_SetPrescaler(USART_TypeDef* USARTx, uint8_t USART_Prescaler) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + + /* Clear the USART prescaler */ + USARTx->GTPR &= USART_GTPR_GT; + /* Set the USART prescaler */ + USARTx->GTPR |= USART_Prescaler; +} + +/** + * @brief Enables or disables the USART's 8x oversampling mode. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USART 8x oversampling mode. + * This parameter can be: ENABLE or DISABLE. + * + * @note + * This function has to be called before calling USART_Init() + * function in order to have correct baudrate Divider value. + * @retval None + */ +void USART_OverSampling8Cmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the 8x Oversampling mode by setting the OVER8 bit in the CR1 register */ + USARTx->CR1 |= USART_CR1_OVER8; + } + else + { + /* Disable the 8x Oversampling mode by clearing the OVER8 bit in the CR1 register */ + USARTx->CR1 &= (uint16_t)~((uint16_t)USART_CR1_OVER8); + } +} + +/** + * @brief Enables or disables the USART's one bit sampling method. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USART one bit sampling method. + * This parameter can be: ENABLE or DISABLE. + * @retval None. + */ +void USART_OneBitMethodCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the one bit method by setting the ONEBITE bit in the CR3 register */ + USARTx->CR3 |= USART_CR3_ONEBIT; + } + else + { + /* Disable the one bit method by clearing the ONEBITE bit in the CR3 register */ + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT); + } +} + +/** + * @} + */ + +/** @defgroup USART_Group2 Data transfers functions + * @brief Data transfers functions + * +@verbatim + =============================================================================== + ##### Data transfers functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage + the USART data transfers. + [..] During an USART reception, data shifts in least significant bit first + through the RX pin. In this mode, the USART_DR register consists of + a buffer (RDR) between the internal bus and the received shift register. + When a transmission is taking place, a write instruction to + the USART_DR register stores the data in the TDR register and which is + copied in the shift register at the end of the current transmission. + [..] The read access of the USART_DR register can be done using + the USART_ReceiveData() function and returns the RDR buffered value. + Whereas a write access to the USART_DR can be done using USART_SendData() + function and stores the written data into TDR buffer. + +@endverbatim + * @{ + */ + +/** + * @brief Transmits single data through the USARTx peripheral. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param Data: the data to transmit. + * @retval None. + */ +void USART_SendData(USART_TypeDef* USARTx, uint16_t Data) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_DATA(Data)); + + /* Transmit Data */ + USARTx->DR = (Data & (uint16_t)0x01FF); +} + +/** + * @brief Returns the most recent received data by the USARTx peripheral. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @retval The received data. + */ +uint16_t USART_ReceiveData(USART_TypeDef* USARTx) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + + /* Receive Data */ + return (uint16_t)(USARTx->DR & (uint16_t)0x01FF); +} + +/** + * @} + */ + +/** @defgroup USART_Group3 MultiProcessor Communication functions + * @brief Multi-Processor Communication functions + * +@verbatim + =============================================================================== + ##### Multi-Processor Communication functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART + multiprocessor communication. + [..] For instance one of the USARTs can be the master, its TX output is + connected to the RX input of the other USART. The others are slaves, + their respective TX outputs are logically ANDed together and connected + to the RX input of the master. USART multiprocessor communication is + possible through the following procedure: + (#) Program the Baud rate, Word length = 9 bits, Stop bits, Parity, + Mode transmitter or Mode receiver and hardware flow control values + using the USART_Init() function. + (#) Configures the USART address using the USART_SetAddress() function. + (#) Configures the wake up methode (USART_WakeUp_IdleLine or + USART_WakeUp_AddressMark) using USART_WakeUpConfig() function only + for the slaves. + (#) Enable the USART using the USART_Cmd() function. + (#) Enter the USART slaves in mute mode using USART_ReceiverWakeUpCmd() + function. + + [..] The USART Slave exit from mute mode when receive the wake up condition. + +@endverbatim + * @{ + */ + +/** + * @brief Sets the address of the USART node. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_Address: Indicates the address of the USART node. + * @retval None + */ +void USART_SetAddress(USART_TypeDef* USARTx, uint8_t USART_Address) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_ADDRESS(USART_Address)); + + /* Clear the USART address */ + USARTx->CR2 &= (uint16_t)~((uint16_t)USART_CR2_ADD); + /* Set the USART address node */ + USARTx->CR2 |= USART_Address; +} + +/** + * @brief Determines if the USART is in mute mode or not. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USART mute mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void USART_ReceiverWakeUpCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the USART mute mode by setting the RWU bit in the CR1 register */ + USARTx->CR1 |= USART_CR1_RWU; + } + else + { + /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */ + USARTx->CR1 &= (uint16_t)~((uint16_t)USART_CR1_RWU); + } +} +/** + * @brief Selects the USART WakeUp method. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_WakeUp: specifies the USART wakeup method. + * This parameter can be one of the following values: + * @arg USART_WakeUp_IdleLine: WakeUp by an idle line detection. + * @arg USART_WakeUp_AddressMark: WakeUp by an address mark. + * @retval None. + */ +void USART_WakeUpConfig(USART_TypeDef* USARTx, uint16_t USART_WakeUp) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_WAKEUP(USART_WakeUp)); + + USARTx->CR1 &= (uint16_t)~((uint16_t)USART_CR1_WAKE); + USARTx->CR1 |= USART_WakeUp; +} + +/** + * @} + */ + +/** @defgroup USART_Group4 LIN mode functions + * @brief LIN mode functions + * +@verbatim + =============================================================================== + ##### LIN mode functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART + LIN Mode communication. + [..] In LIN mode, 8-bit data format with 1 stop bit is required in accordance + with the LIN standard. + [..] Only this LIN Feature is supported by the USART IP: + (+) LIN Master Synchronous Break send capability and LIN slave break + detection capability : 13-bit break generation and 10/11 bit break + detection. + [..] USART LIN Master transmitter communication is possible through the + following procedure: + (#) Program the Baud rate, Word length = 8bits, Stop bits = 1bit, Parity, + Mode transmitter or Mode receiver and hardware flow control values + using the USART_Init() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Enable the LIN mode using the USART_LINCmd() function. + (#) Send the break character using USART_SendBreak() function. + [..] USART LIN Master receiver communication is possible through the + following procedure: + (#) Program the Baud rate, Word length = 8bits, Stop bits = 1bit, Parity, + Mode transmitter or Mode receiver and hardware flow control values + using the USART_Init() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Configures the break detection length + using the USART_LINBreakDetectLengthConfig() function. + (#) Enable the LIN mode using the USART_LINCmd() function. + -@- In LIN mode, the following bits must be kept cleared: + (+@) CLKEN in the USART_CR2 register. + (+@) STOP[1:0], SCEN, HDSEL and IREN in the USART_CR3 register. + +@endverbatim + * @{ + */ + +/** + * @brief Sets the USART LIN Break detection length. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_LINBreakDetectLength: specifies the LIN break detection length. + * This parameter can be one of the following values: + * @arg USART_LINBreakDetectLength_10b: 10-bit break detection. + * @arg USART_LINBreakDetectLength_11b: 11-bit break detection. + * @retval None. + */ +void USART_LINBreakDetectLengthConfig(USART_TypeDef* USARTx, uint16_t USART_LINBreakDetectLength) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_LIN_BREAK_DETECT_LENGTH(USART_LINBreakDetectLength)); + + USARTx->CR2 &= (uint16_t)~((uint16_t)USART_CR2_LBDL); + USARTx->CR2 |= USART_LINBreakDetectLength; +} + +/** + * @brief Enables or disables the USART's LIN mode. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USART LIN mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None. + */ +void USART_LINCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the LIN mode by setting the LINEN bit in the CR2 register */ + USARTx->CR2 |= USART_CR2_LINEN; + } + else + { + /* Disable the LIN mode by clearing the LINEN bit in the CR2 register */ + USARTx->CR2 &= (uint16_t)~((uint16_t)USART_CR2_LINEN); + } +} + +/** + * @brief Transmits break characters. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @retval None. + */ +void USART_SendBreak(USART_TypeDef* USARTx) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + + /* Send break characters */ + USARTx->CR1 |= USART_CR1_SBK; +} + +/** + * @} + */ + +/** @defgroup USART_Group5 Halfduplex mode function + * @brief Half-duplex mode function + * +@verbatim + =============================================================================== + ##### Half-duplex mode function ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART + Half-duplex communication. + [..] The USART can be configured to follow a single-wire half-duplex protocol + where the TX and RX lines are internally connected. + [..] USART Half duplex communication is possible through the following procedure: + (#) Program the Baud rate, Word length, Stop bits, Parity, Mode transmitter + or Mode receiver and hardware flow control values using the USART_Init() + function. + (#) Configures the USART address using the USART_SetAddress() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Enable the half duplex mode using USART_HalfDuplexCmd() function. + -@- The RX pin is no longer used. + -@- In Half-duplex mode the following bits must be kept cleared: + (+@) LINEN and CLKEN bits in the USART_CR2 register. + (+@) SCEN and IREN bits in the USART_CR3 register. + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the USART's Half Duplex communication. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the USART Communication. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void USART_HalfDuplexCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */ + USARTx->CR3 |= USART_CR3_HDSEL; + } + else + { + /* Disable the Half-Duplex mode by clearing the HDSEL bit in the CR3 register */ + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_HDSEL); + } +} + +/** + * @} + */ + + +/** @defgroup USART_Group6 Smartcard mode functions + * @brief Smartcard mode functions + * +@verbatim + =============================================================================== + ##### Smartcard mode functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART + Smartcard communication. + [..] The Smartcard interface is designed to support asynchronous protocol + Smartcards as defined in the ISO 7816-3 standard. The USART can provide + a clock to the smartcard through the SCLK output. In smartcard mode, + SCLK is not associated to the communication but is simply derived from + the internal peripheral input clock through a 5-bit prescaler. + [..] Smartcard communication is possible through the following procedure: + (#) Configures the Smartcard Prsecaler using the USART_SetPrescaler() + function. + (#) Configures the Smartcard Guard Time using the USART_SetGuardTime() + function. + (#) Program the USART clock using the USART_ClockInit() function as following: + (++) USART Clock enabled. + (++) USART CPOL Low. + (++) USART CPHA on first edge. + (++) USART Last Bit Clock Enabled. + (#) Program the Smartcard interface using the USART_Init() function as + following: + (++) Word Length = 9 Bits. + (++) 1.5 Stop Bit. + (++) Even parity. + (++) BaudRate = 12096 baud. + (++) Hardware flow control disabled (RTS and CTS signals). + (++) Tx and Rx enabled + (#) Optionally you can enable the parity error interrupt using + the USART_ITConfig() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Enable the Smartcard NACK using the USART_SmartCardNACKCmd() function. + (#) Enable the Smartcard interface using the USART_SmartCardCmd() function. + [..] + Please refer to the ISO 7816-3 specification for more details. + [..] + (@) It is also possible to choose 0.5 stop bit for receiving but it is + recommended to use 1.5 stop bits for both transmitting and receiving + to avoid switching between the two configurations. + (@) In smartcard mode, the following bits must be kept cleared: + (+@) LINEN bit in the USART_CR2 register. + (+@) HDSEL and IREN bits in the USART_CR3 register. + +@endverbatim + * @{ + */ + +/** + * @brief Sets the specified USART guard time. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2 or USART3. + * @param USART_GuardTime: specifies the guard time. + * @retval None. + */ +void USART_SetGuardTime(USART_TypeDef* USARTx, uint8_t USART_GuardTime) +{ + /* Check the parameters */ + assert_param(IS_USART_123_PERIPH(USARTx)); + + /* Clear the USART Guard time */ + USARTx->GTPR &= USART_GTPR_PSC; + /* Set the USART guard time */ + USARTx->GTPR |= (uint16_t)((uint16_t)USART_GuardTime << 0x08); +} + +/** + * @brief Enables or disables the USART's Smart Card mode. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2 or USART3. + * @param NewState: new state of the Smart Card mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void USART_SmartCardCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_123_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + if (NewState != DISABLE) + { + /* Enable the SC mode by setting the SCEN bit in the CR3 register */ + USARTx->CR3 |= USART_CR3_SCEN; + } + else + { + /* Disable the SC mode by clearing the SCEN bit in the CR3 register */ + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_SCEN); + } +} + +/** + * @brief Enables or disables NACK transmission. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2 or USART3. + * @param NewState: new state of the NACK transmission. + * This parameter can be: ENABLE or DISABLE. + * @retval None. + */ +void USART_SmartCardNACKCmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_123_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + if (NewState != DISABLE) + { + /* Enable the NACK transmission by setting the NACK bit in the CR3 register */ + USARTx->CR3 |= USART_CR3_NACK; + } + else + { + /* Disable the NACK transmission by clearing the NACK bit in the CR3 register */ + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_NACK); + } +} + +/** + * @} + */ + +/** @defgroup USART_Group7 IrDA mode functions + * @brief IrDA mode functions + * +@verbatim + =============================================================================== + ##### IrDA mode functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART + IrDA communication. + [..] IrDA is a half duplex communication protocol. If the Transmitter is busy, + any data on the IrDA receive line will be ignored by the IrDA decoder + and if the Receiver is busy, data on the TX from the USART to IrDA will + not be encoded by IrDA. While receiving data, transmission should be + avoided as the data to be transmitted could be corrupted. + + [..] IrDA communication is possible through the following procedure: + (#) Program the Baud rate, Word length = 8 bits, Stop bits, Parity, + Transmitter/Receiver modes and hardware flow control values using + the USART_Init() function. + (#) Enable the USART using the USART_Cmd() function. + (#) Configures the IrDA pulse width by configuring the prescaler using + the USART_SetPrescaler() function. + (#) Configures the IrDA USART_IrDAMode_LowPower or USART_IrDAMode_Normal + mode using the USART_IrDAConfig() function. + (#) Enable the IrDA using the USART_IrDACmd() function. + + [..] + (@) A pulse of width less than two and greater than one PSC period(s) may or + may not be rejected. + (@) The receiver set up time should be managed by software. The IrDA physical + layer specification specifies a minimum of 10 ms delay between + transmission and reception (IrDA is a half duplex protocol). + (@) In IrDA mode, the following bits must be kept cleared: + (+@) LINEN, STOP and CLKEN bits in the USART_CR2 register. + (+@) SCEN and HDSEL bits in the USART_CR3 register. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the USART's IrDA interface. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_IrDAMode: specifies the IrDA mode. + * This parameter can be one of the following values: + * @arg USART_IrDAMode_LowPower: USART IrDA Low Power mode selected. + * @arg USART_IrDAMode_Normal: USART IrDA Normal mode selected. + * @retval None + */ +void USART_IrDAConfig(USART_TypeDef* USARTx, uint16_t USART_IrDAMode) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_IRDA_MODE(USART_IrDAMode)); + + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_IRLP); + USARTx->CR3 |= USART_IrDAMode; +} + +/** + * @brief Enables or disables the USART's IrDA interface. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param NewState: new state of the IrDA mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void USART_IrDACmd(USART_TypeDef* USARTx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the IrDA mode by setting the IREN bit in the CR3 register */ + USARTx->CR3 |= USART_CR3_IREN; + } + else + { + /* Disable the IrDA mode by clearing the IREN bit in the CR3 register */ + USARTx->CR3 &= (uint16_t)~((uint16_t)USART_CR3_IREN); + } +} + +/** + * @} + */ + +/** @defgroup USART_Group8 DMA transfers management functions + * @brief DMA transfers management functions + * +@verbatim + =============================================================================== + ##### DMA transfers management functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the USART's DMA interface. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_DMAReq: specifies the DMA request. + * This parameter can be any combination of the following values: + * @arg USART_DMAReq_Tx: USART DMA transmit request. + * @arg USART_DMAReq_Rx: USART DMA receive request. + * @param NewState: new state of the DMA Request sources. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_DMAREQ(USART_DMAReq)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the DMA transfer for selected requests by setting the DMAT and/or + DMAR bits in the USART CR3 register */ + USARTx->CR3 |= USART_DMAReq; + } + else + { + /* Disable the DMA transfer for selected requests by clearing the DMAT and/or + DMAR bits in the USART CR3 register */ + USARTx->CR3 &= (uint16_t)~USART_DMAReq; + } +} + +/** + * @} + */ + +/** @defgroup USART_Group9 Interrupts and flags management functions + * @brief Interrupts and flags management functions + * +@verbatim + =============================================================================== + ##### Interrupts and flags management functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to configure the + USART Interrupts sources, DMA channels requests and check or clear the + flags or pending bits status. The user should identify which mode will + be used in his application to manage the communication: Polling mode, + Interrupt mode or DMA mode. + *** Polling Mode *** + ==================== + [..] In Polling Mode, the SPI communication can be managed by 10 flags: + (#) USART_FLAG_TXE: to indicate the status of the transmit buffer register. + (#) USART_FLAG_RXNE: to indicate the status of the receive buffer register. + (#) USART_FLAG_TC: to indicate the status of the transmit operation. + (#) USART_FLAG_IDLE: to indicate the status of the Idle Line. + (#) USART_FLAG_CTS: to indicate the status of the nCTS input. + (#) USART_FLAG_LBD: to indicate the status of the LIN break detection. + (#) USART_FLAG_NE: to indicate if a noise error occur. + (#) USART_FLAG_FE: to indicate if a frame error occur. + (#) USART_FLAG_PE: to indicate if a parity error occur. + (#) USART_FLAG_ORE: to indicate if an Overrun error occur. + [..] In this Mode it is advised to use the following functions: + (+) FlagStatus USART_GetFlagStatus(USART_TypeDef* USARTx, uint16_t USART_FLAG). + (+) void USART_ClearFlag(USART_TypeDef* USARTx, uint16_t USART_FLAG). + + *** Interrupt Mode *** + ====================== + [..] In Interrupt Mode, the USART communication can be managed by 8 interrupt + sources and 10 pending bits: + (+) Pending Bits: + (##) USART_IT_TXE: to indicate the status of the transmit buffer + register. + (##) USART_IT_RXNE: to indicate the status of the receive buffer + register. + (##) USART_IT_TC: to indicate the status of the transmit operation. + (##) USART_IT_IDLE: to indicate the status of the Idle Line. + (##) USART_IT_CTS: to indicate the status of the nCTS input. + (##) USART_IT_LBD: to indicate the status of the LIN break detection. + (##) USART_IT_NE: to indicate if a noise error occur. + (##) USART_IT_FE: to indicate if a frame error occur. + (##) USART_IT_PE: to indicate if a parity error occur. + (##) USART_IT_ORE: to indicate if an Overrun error occur + (if the RXNEIE or EIE bits are set). + + (+) Interrupt Source: + (##) USART_IT_TXE: specifies the interrupt source for the Tx buffer + empty interrupt. + (##) USART_IT_RXNE: specifies the interrupt source for the Rx buffer + not empty interrupt. + (##) USART_IT_TC: specifies the interrupt source for the Transmit + complete interrupt. + (##) USART_IT_IDLE: specifies the interrupt source for the Idle Line + interrupt. + (##) USART_IT_CTS: specifies the interrupt source for the CTS interrupt. + (##) USART_IT_LBD: specifies the interrupt source for the LIN break + detection interrupt. + (##) USART_IT_PE: specifies the interrupt source for theparity error + interrupt. + (##) USART_IT_ERR: specifies the interrupt source for the errors + interrupt. + -@@- Some parameters are coded in order to use them as interrupt + source or as pending bits. + [..] In this Mode it is advised to use the following functions: + (+) void USART_ITConfig(USART_TypeDef* USARTx, uint16_t USART_IT, + FunctionalState NewState). + (+) ITStatus USART_GetITStatus(USART_TypeDef* USARTx, uint16_t USART_IT). + (+) void USART_ClearITPendingBit(USART_TypeDef* USARTx, uint16_t USART_IT). + + *** DMA Mode *** + ================ + [..] In DMA Mode, the USART communication can be managed by 2 DMA Channel + requests: + (#) USART_DMAReq_Tx: specifies the Tx buffer DMA transfer request. + (#) USART_DMAReq_Rx: specifies the Rx buffer DMA transfer request. + [..] In this Mode it is advised to use the following function: + (+) void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, + FunctionalState NewState). +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the specified USART interrupts. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_IT: specifies the USART interrupt sources to be enabled or disabled. + * This parameter can be one of the following values: + * @arg USART_IT_CTS: CTS change interrupt. + * @arg USART_IT_LBD: LIN Break detection interrupt. + * @arg USART_IT_TXE: Tansmit Data Register empty interrupt. + * @arg USART_IT_TC: Transmission complete interrupt. + * @arg USART_IT_RXNE: Receive Data register not empty interrupt. + * @arg USART_IT_IDLE: Idle line detection interrupt. + * @arg USART_IT_PE: Parity Error interrupt. + * @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error). + * @param NewState: new state of the specified USARTx interrupts. + * This parameter can be: ENABLE or DISABLE. + * @retval None. + */ +void USART_ITConfig(USART_TypeDef* USARTx, uint16_t USART_IT, FunctionalState NewState) +{ + uint32_t usartreg = 0x00, itpos = 0x00, itmask = 0x00; + uint32_t usartxbase = 0x00; + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_CONFIG_IT(USART_IT)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + /* The CTS interrupt is not available for UART4 and UART5 */ + if (USART_IT == USART_IT_CTS) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + + usartxbase = (uint32_t)USARTx; + + /* Get the USART register index */ + usartreg = (((uint8_t)USART_IT) >> 0x05); + + /* Get the interrupt position */ + itpos = USART_IT & IT_MASK; + itmask = (((uint32_t)0x01) << itpos); + + if (usartreg == 0x01) /* The IT is in CR1 register */ + { + usartxbase += 0x0C; + } + else if (usartreg == 0x02) /* The IT is in CR2 register */ + { + usartxbase += 0x10; + } + else /* The IT is in CR3 register */ + { + usartxbase += 0x14; + } + if (NewState != DISABLE) + { + *(__IO uint32_t*)usartxbase |= itmask; + } + else + { + *(__IO uint32_t*)usartxbase &= ~itmask; + } +} + +/** + * @brief Checks whether the specified USART flag is set or not. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5). + * @arg USART_FLAG_LBD: LIN Break detection flag. + * @arg USART_FLAG_TXE: Transmit data register empty flag. + * @arg USART_FLAG_TC: Transmission Complete flag. + * @arg USART_FLAG_RXNE: Receive data register not empty flag. + * @arg USART_FLAG_IDLE: Idle Line detection flag. + * @arg USART_FLAG_ORE: OverRun Error flag. + * @arg USART_FLAG_NE: Noise Error flag. + * @arg USART_FLAG_FE: Framing Error flag. + * @arg USART_FLAG_PE: Parity Error flag. + * @retval The new state of USART_FLAG (SET or RESET). + */ +FlagStatus USART_GetFlagStatus(USART_TypeDef* USARTx, uint16_t USART_FLAG) +{ + FlagStatus bitstatus = RESET; + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_FLAG(USART_FLAG)); + + /* The CTS flag is not available for UART4 and UART5 */ + if (USART_FLAG == USART_FLAG_CTS) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + + if ((USARTx->SR & USART_FLAG) != (uint16_t)RESET) + { + bitstatus = SET; + } + else + { + bitstatus = RESET; + } + return bitstatus; +} + +/** + * @brief Clears the USARTx's pending flags. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_FLAG: specifies the flag to clear. + * This parameter can be any combination of the following values: + * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5). + * @arg USART_FLAG_LBD: LIN Break detection flag. + * @arg USART_FLAG_TC: Transmission Complete flag. + * @arg USART_FLAG_RXNE: Receive data register not empty flag. + * + * + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun + * error) and IDLE (Idle line detected) flags are cleared by software + * sequence: a read operation to USART_SR register (USART_GetFlagStatus()) + * followed by a read operation to USART_DR register (USART_ReceiveData()). + * @note RXNE flag can be also cleared by a read to the USART_DR register + * (USART_ReceiveData()). + * @note TC flag can be also cleared by software sequence: a read operation to + * USART_SR register (USART_GetFlagStatus()) followed by a write operation + * to USART_DR register (USART_SendData()). + * @note TXE flag is cleared only by a write to the USART_DR register + * (USART_SendData()). + * @retval None + */ +void USART_ClearFlag(USART_TypeDef* USARTx, uint16_t USART_FLAG) +{ + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_CLEAR_FLAG(USART_FLAG)); + + /* The CTS flag is not available for UART4 and UART5 */ + if ((USART_FLAG & USART_FLAG_CTS) == USART_FLAG_CTS) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + + USARTx->SR = (uint16_t)~USART_FLAG; +} + +/** + * @brief Checks whether the specified USART interrupt has occurred or not. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_IT: specifies the USART interrupt source to check. + * This parameter can be one of the following values: + * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) + * @arg USART_IT_LBD: LIN Break detection interrupt + * @arg USART_IT_TXE: Tansmit Data Register empty interrupt + * @arg USART_IT_TC: Transmission complete interrupt + * @arg USART_IT_RXNE: Receive Data register not empty interrupt + * @arg USART_IT_IDLE: Idle line detection interrupt + * @arg USART_IT_ORE_RX: OverRun Error interrupt if the RXNEIE bit is set. + * @arg USART_IT_ORE_ER: OverRun Error interrupt if the EIE bit is set. + * @arg USART_IT_NE: Noise Error interrupt + * @arg USART_IT_FE: Framing Error interrupt + * @arg USART_IT_PE: Parity Error interrupt + * @retval The new state of USART_IT (SET or RESET). + */ +ITStatus USART_GetITStatus(USART_TypeDef* USARTx, uint16_t USART_IT) +{ + uint32_t bitpos = 0x00, itmask = 0x00, usartreg = 0x00; + ITStatus bitstatus = RESET; + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_GET_IT(USART_IT)); + + /* The CTS interrupt is not available for UART4 and UART5 */ + if (USART_IT == USART_IT_CTS) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + + /* Get the USART register index */ + usartreg = (((uint8_t)USART_IT) >> 0x05); + /* Get the interrupt position */ + itmask = USART_IT & IT_MASK; + itmask = (uint32_t)0x01 << itmask; + + if (usartreg == 0x01) /* The IT is in CR1 register */ + { + itmask &= USARTx->CR1; + } + else if (usartreg == 0x02) /* The IT is in CR2 register */ + { + itmask &= USARTx->CR2; + } + else /* The IT is in CR3 register */ + { + itmask &= USARTx->CR3; + } + + bitpos = USART_IT >> 0x08; + bitpos = (uint32_t)0x01 << bitpos; + bitpos &= USARTx->SR; + if ((itmask != (uint16_t)RESET)&&(bitpos != (uint16_t)RESET)) + { + bitstatus = SET; + } + else + { + bitstatus = RESET; + } + + return bitstatus; +} + +/** + * @brief Clears the USARTx's interrupt pending bits. + * @param USARTx: Select the USART peripheral. + * This parameter can be one of the following values: + * USART1, USART2, USART3, UART4 or UART5. + * @param USART_IT: specifies the interrupt pending bit to clear. + * This parameter can be one of the following values: + * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) + * @arg USART_IT_LBD: LIN Break detection interrupt + * @arg USART_IT_TC: Transmission complete interrupt. + * @arg USART_IT_RXNE: Receive Data register not empty interrupt. + * + + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun + * error) and IDLE (Idle line detected) pending bits are cleared by + * software sequence: a read operation to USART_SR register + * (USART_GetITStatus()) followed by a read operation to USART_DR register + * (USART_ReceiveData()). + * @note RXNE pending bit can be also cleared by a read to the USART_DR register + * (USART_ReceiveData()). + * @note TC pending bit can be also cleared by software sequence: a read + * operation to USART_SR register (USART_GetITStatus()) followed by a write + * operation to USART_DR register (USART_SendData()). + * @note TXE pending bit is cleared only by a write to the USART_DR register + * (USART_SendData()). + * @retval None + */ +void USART_ClearITPendingBit(USART_TypeDef* USARTx, uint16_t USART_IT) +{ + uint16_t bitpos = 0x00, itmask = 0x00; + /* Check the parameters */ + assert_param(IS_USART_ALL_PERIPH(USARTx)); + assert_param(IS_USART_CLEAR_IT(USART_IT)); + + /* The CTS interrupt is not available for UART4 and UART5 */ + if (USART_IT == USART_IT_CTS) + { + assert_param(IS_USART_123_PERIPH(USARTx)); + } + + bitpos = USART_IT >> 0x08; + itmask = ((uint16_t)0x01 << (uint16_t)bitpos); + USARTx->SR = (uint16_t)~itmask; +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/