mbed library sources
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F3XX/stm32f30x_misc.c
- Revision:
- 155:8435094ec241
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32F3XX/stm32f30x_misc.c Tue Apr 08 09:15:06 2014 +0100 @@ -0,0 +1,240 @@ +/** + ****************************************************************************** + * @file stm32f30x_misc.c + * @author MCD Application Team + * @version V1.1.0 + * @date 27-February-2014 + * @brief This file provides all the miscellaneous firmware functions (add-on + * to CMSIS functions). + * + @verbatim + + =============================================================================== + ##### How to configure Interrupts using driver ##### + =============================================================================== + [..] This section provide functions allowing to configure the NVIC interrupts + (IRQ). The Cortex-M4 exceptions are managed by CMSIS functions. + (#) Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig() + function according to the following table. + The table below gives the allowed values of the pre-emption priority + and subpriority according to the Priority Grouping configuration + performed by NVIC_PriorityGroupConfig function. + + (#) Enable and Configure the priority of the selected IRQ Channels. + [..] + (@) When the NVIC_PriorityGroup_0 is selected, it will no any nested interrupt, + the IRQ priority will be managed only by subpriority. + The sub-priority is only used to sort pending exception priorities, + and does not affect active exceptions. + (@) Lower priority values gives higher priority. + (@) Priority Order: + (#@) Lowest Preemption priority. + (#@) Lowest Subpriority. + (#@) Lowest hardware priority (IRQn position). + + @endverbatim + + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f30x_misc.h" + +/** @addtogroup STM32F30x_StdPeriph_Driver + * @{ + */ + +/** @defgroup MISC + * @brief MISC driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define AIRCR_VECTKEY_MASK ((uint32_t)0x05FA0000) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup MISC_Private_Functions + * @{ + */ + +/** + * @brief Configures the priority grouping: pre-emption priority and subpriority. + * @param NVIC_PriorityGroup: specifies the priority grouping bits length. + * This parameter can be one of the following values: + * @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority. + * 4 bits for subpriority. + * @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority. + * 3 bits for subpriority. + * @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority. + * 2 bits for subpriority. + * @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority. + * 1 bits for subpriority. + * @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority. + * 0 bits for subpriority. + * @note When NVIC_PriorityGroup_0 is selected, it will no be any nested + * interrupt. This interrupts priority is managed only with subpriority. + * @retval None + */ +void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup) +{ + /* Check the parameters */ + assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup)); + + /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */ + SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup; +} + +/** + * @brief Initializes the NVIC peripheral according to the specified + * parameters in the NVIC_InitStruct. + * @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig() + * function should be called before. + * @param NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains + * the configuration information for the specified NVIC peripheral. + * @retval None + */ +void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct) +{ + uint32_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F; + + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd)); + assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority)); + assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority)); + + if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE) + { + /* Compute the Corresponding IRQ Priority --------------------------------*/ + tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08; + tmppre = (0x4 - tmppriority); + tmpsub = tmpsub >> tmppriority; + + tmppriority = (uint32_t)NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre; + tmppriority |= NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub; + tmppriority = tmppriority << 0x04; + + NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority; + + /* Enable the Selected IRQ Channels --------------------------------------*/ + NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] = + (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F); + } + else + { + /* Disable the Selected IRQ Channels -------------------------------------*/ + NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] = + (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F); + } +} + +/** + * @brief Sets the vector table location and Offset. + * @param NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory. + * This parameter can be one of the following values: + * @arg NVIC_VectTab_RAM + * @arg NVIC_VectTab_FLASH + * @param Offset: Vector Table base offset field. This value must be a multiple of 0x200. + * @retval None + */ +void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset) +{ + /* Check the parameters */ + assert_param(IS_NVIC_VECTTAB(NVIC_VectTab)); + assert_param(IS_NVIC_OFFSET(Offset)); + + SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80); +} + +/** + * @brief Selects the condition for the system to enter low power mode. + * @param LowPowerMode: Specifies the new mode for the system to enter low power mode. + * This parameter can be one of the following values: + * @arg NVIC_LP_SEVONPEND + * @arg NVIC_LP_SLEEPDEEP + * @arg NVIC_LP_SLEEPONEXIT + * @param NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_NVIC_LP(LowPowerMode)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + SCB->SCR |= LowPowerMode; + } + else + { + SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode); + } +} + +/** + * @brief Configures the SysTick clock source. + * @param SysTick_CLKSource: specifies the SysTick clock source. + * This parameter can be one of the following values: + * @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source. + * @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source. + * @retval None + */ +void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource) +{ + /* Check the parameters */ + assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource)); + if (SysTick_CLKSource == SysTick_CLKSource_HCLK) + { + SysTick->CTRL |= SysTick_CLKSource_HCLK; + } + else + { + SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8; + } +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/