Diff: TextLCD_Config.h

Revision:

42:e4ea7c53a785

Parent:

41:111ca62e8a59

diff -r 111ca62e8a59 -r e4ea7c53a785 TextLCD_Config.h
--- a/TextLCD_Config.h	Fri Nov 06 18:59:27 2015 +0000
+++ b/TextLCD_Config.h	Thu Mar 12 16:25:59 2020 +0000
@@ -4,10 +4,10 @@
  *               2014, v02: WH, Added AC780 support, added I2C expander modules, fixed setBacklight() for inverted logic modules. Fixed bug in LCD_SPI_N define
  *               2014, v03: WH, Added LCD_SPI_N_3_8 define for ST7070
  *               2015, v04: WH, Added support for alternative fonttables (eg PCF21XX)
- *               2015, v05: WH, Clean up low-level _writeCommand() and _writeData(), Added support for alt fonttables (eg PCF21XX), Added ST7066_ACM for ACM1602 module, fixed contrast for ST7032 
+ *               2015, v05: WH, Clean up low-level _writeCommand() and _writeData(), Added support for alt fonttables (eg PCF21XX), Added ST7066_ACM for ACM1602 module, fixed contrast for ST7032
  *               2015, v06: WH, Performance improvement I2C portexpander
  *               2015, v07: WH, Fixed Adafruit I2C/SPI portexpander pinmappings, fixed SYDZ Backlight
- *               2015, v08: WH, Added defines to reduce memory footprint (eg LCD_ICON), added some I2C portexpander defines 
+ *               2015, v08: WH, Added defines to reduce memory footprint (eg LCD_ICON), added some I2C portexpander defines
  *               2015, v09: WH, Added defines to reduce memory footprint (LCD_TWO_CTRL, LCD_CONTRAST, LCD_UTF8_FONT),
  *                              Added UTF8_2_LCD decode for Cyrilic font (By Andriy Ribalko). Added setFont()
  *
@@ -68,10 +68,10 @@
 //LCD and serial portexpanders should be wired according to the tables below.
 //
 //Select Serial Port Expander Hardware module (one option only)
-#define DEFAULT        1
+#define DEFAULT        0
 #define ADAFRUIT       0
 #define DFROBOT        0
-#define LCM1602        0
+#define LCM1602        1
 #define YWROBOT        0
 #define GYLCD          0
 #define MJKDZ          0
@@ -100,7 +100,7 @@
 
 #define LCD_BUS_I2C_RW (1 << 6)
 
-//SPI bus expander (74595) interface, same as I2C 
+//SPI bus expander (74595) interface, same as I2C
 #define LCD_BUS_SPI_D4 LCD_BUS_I2C_D4
 #define LCD_BUS_SPI_D5 LCD_BUS_I2C_D5
 #define LCD_BUS_SPI_D6 LCD_BUS_I2C_D6
@@ -171,7 +171,7 @@
 //Slaveaddress hardwired to 0x4E. SDA/SCL has pullup Resistors onboard.
 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
 //
-//Definitions for DFROBOT V1.1 
+//Definitions for DFROBOT V1.1
 //This hardware uses PCF8574. Slaveaddress may be set by jumpers (default 0x40).
 //SDA/SCL has pullup Resistors onboard and features a voltage level converter 3V3 <-> 5V.
 //See http://www.dfrobot.com/index.php?route=product/product&product_id=135
@@ -215,7 +215,7 @@
 #endif
 
 #if ((YWROBOT==1) || (LCM1602==1))
-//Definitions for YWROBOT LCM1602 V1 Module mapping between serial port expander pins and LCD controller. 
+//Definitions for YWROBOT LCM1602 V1 Module mapping between serial port expander pins and LCD controller.
 //Very similar to DFROBOT. Also marked as 'Funduino'. This hardware uses PCF8574.
 //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has no pullup Resistors onboard.
 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
@@ -257,7 +257,7 @@
 #endif
 
 #if ((GYLCD==1) || (MJKDZ==1))
-//Definitions for Arduino-IIC-LCD GY-LCD-V1, for GY-IICLCD and for MJKDZ Module mapping between serial port expander pins and LCD controller. 
+//Definitions for Arduino-IIC-LCD GY-LCD-V1, for GY-IICLCD and for MJKDZ Module mapping between serial port expander pins and LCD controller.
 //Very similar to DFROBOT. This hardware uses PCF8574.
 //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has pullup Resistors onboard.
 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
@@ -299,7 +299,7 @@
 #endif
 
 #if (SYDZ==1)
-//Definitions for SYDZ Module mapping between serial port expander pins and LCD controller. 
+//Definitions for SYDZ Module mapping between serial port expander pins and LCD controller.
 //Very similar to DFROBOT. This hardware uses PCF8574A.
 //Slaveaddress may be set by switches (default 0x70). SDA/SCL has pullup Resistors onboard.
 //See ebay
@@ -545,7 +545,7 @@
 // 5: 4.000V
 // 6: 4.444V
 // 7: 5.000V
-#define LCD_ST7032_CONTRAST 0x28 
+#define LCD_ST7032_CONTRAST 0x28
 #define LCD_ST7032_RAB      0x04
 
 //ST7036 EA DOGM1603 display
@@ -581,7 +581,7 @@
 // 0: 1.818V
 // 1: 2.222V
 // 2: 2.667V
-// 3: 3.333V (SPLC792A default) 
+// 3: 3.333V (SPLC792A default)
 // 4: 3.636V
 // 5: 4.000V
 // 6: 4.444V