![](/media/cache/profiles/cfee7edeb341158110ece5fba9440f58.jpg.50x50_q85.jpg)
this is a small prototype for color sensor, which can detect three colors... this was made by using an LDR,1.5 K resistor and the wiz wiki 7500 board
Fork of ADC_test by
the things you need for this are wiznet board or any other micro controller can do it when you understand the logic i have applied here.An LDR and one resistor for your reference i have used 1.5K resistor in my work.
connect the LDR and resistor in series in between the 3.3V and GND of the board.take outpt from the point where LDR and resistor met.
it's just an voltage divider circuit depends on the color you subject to LDR the resistance of LDR will vary and the volatge also does the same.
then feed the output on the adc pin of micro controller, then you will get various values for various colors. the adc which i have used is 12 bit one that's why it's having 4096 count. you have to change the values in the program according to your adc count.
sorry for my bad english.........
main.cpp
- Committer:
- simonb
- Date:
- 2010-02-10
- Revision:
- 0:a2562dfbf543
- Child:
- 1:c88c8173b9b2
File content as of revision 0:a2562dfbf543:
#define SAMPLE_RATE 150000 #include "mbed.h" #include "adc.h" DigitalOut int_led(LED1); //Initialise ADC to maximum SAMPLE_RATE and cclk divide set to 1 ADC adc(SAMPLE_RATE, 1); //Toggle LED on interrupt void led_toggle(int chan, uint32_t value) { int_led = !int_led; } //Report ADC value on interrupt void print_value(int chan, uint32_t value) { printf("ADC interrupt on pin %u, value=%04u.\n", adc.channel_to_pin_number(chan), (value >> 4) & 0xFFF); } int main() { int i; printf("Requested max sample rate is %u, actual max sample rate is %u.\n", SAMPLE_RATE, adc.actual_sample_rate()); while (1) { //Set up ADC on pin 20 adc.setup(p20,1); //Set up ADC on pin 19 adc.setup(p19,1); wait(1); //Measure pin 20 adc.select(p20); //Start ADC conversion adc.start(); //Wait for it to complete while(!adc.done(p20)); printf("Measured value on pin 20 is %04u.\n", adc.read(p20)); wait(1); //Measure pin 19 adc.select(p19); //Start ADC conversion adc.start(); //Wait for it to complete while(!adc.done(p19)); printf("Measured value on pin 19 is %04u.\n", adc.read(p19)); wait(1); //Append an interrupt handler that prints the channel and value adc.append(print_value); //Measure pin 20 adc.select(p20); //Enable the interrupt adc.interrupt_state(p20,1); //Start ADC conversion adc.start(); //Wait for it to complete while(!adc.done(p20)); wait(1); //Unset pin 20 adc.setup(p20,0); //Togle LED on each converstion. //Should be 12.5KHz on LED for all 6 pins. //Sample rate=150KHz / 6 channels / 2 adc.append(led_toggle); //Prepare for burst mode on all ADC pins adc.startmode(0,0); adc.burst(1); adc.setup(p20,1); adc.setup(p19,1); adc.setup(p18,1); adc.setup(p17,1); adc.setup(p16,1); adc.setup(p15,1); //For burst mode, only one interrupt is required //which can be on any enabled pin. We have enabled all //of them here. adc.interrupt_state(p15,1); printf("Burst mode, printing once per second...\n"); for (i=0; i<5; i++) { printf("%04u %04u %04u %04u %04u %04u\n", adc.read(p20), adc.read(p19), adc.read(p18), adc.read(p17), adc.read(p16), adc.read(p15)); wait(1); } adc.burst(0); adc.setup(p20,0); adc.setup(p19,0); adc.setup(p18,0); adc.setup(p17,0); adc.setup(p16,0); adc.setup(p15,0); adc.interrupt_state(p20,0); adc.interrupt_state(p19,0); adc.interrupt_state(p18,0); adc.interrupt_state(p17,0); adc.interrupt_state(p16,0); adc.interrupt_state(p15,0); printf("\n"); } }