![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
Final Beacon code for testing
Diff: main.cpp
- Revision:
- 0:e4162b2d1a79
- Child:
- 1:8b18c140a710
diff -r 000000000000 -r e4162b2d1a79 main.cpp --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/main.cpp Mon Oct 05 13:52:48 2015 +0000 @@ -0,0 +1,425 @@ +#include "tx.h" +#include <stdio.h> + +Ticker loop; +Serial pc(USBTX, USBRX); //tx,rx +SPI spi(D11, D12, D13); // mosi, miso, sclk +DigitalOut cs(D10); //slave select or chip select + +Timer t; + +void P_BCN_INIT() +{ + BCN_INIT_STATUS = 1; + //check initialization parameters + Init_BEACON_HW(); + //t.start(); + BCN_INIT_STATUS = 0; +} +void P_BCN_FEN() +{ + BCN_FEN = 1; +} +void P_BCN_TX_MAIN() +{ + BCN_TX_MAIN_STATUS = 1; + + if(BCN_FEN == 1) + { + if(BCN_TX_EN == 1) + { + //Measure and store BCN temperature in BCN_TS_BUFFER + BCN_TS_BUFFER = ((check_Temperature())*0.5) - 64; + + //Get BCN_HK data from BCN HW(SPI) //Store BCN_HK data in BCN_HK_BUFFER + if(BCN_STANDBY == 1 ) + { + Set_BCN_TX_STATUS(BCN_TX_STANDBY); + BCN_TX_MAIN_STATUS = 0; + + // break; + } + else + { + //pc.printf("in BCN_TX_STANDBY != 1\r\n"); + + t.start(); + int begin = t.read(); + SHORT_BCN_TX(); + LONG_BCN_TX(); + int end = t.read(); + pc.printf("The time required for short and long is %d seconds\r\n", end-begin); + pc.printf("Short and Long packets sent\r\n"); + //include LONG_BCN_TX also + if(Check_ACK_RECEIVED() == 1) + { + Set_BCN_TX_STATUS(BCN_TX_SUCCESS); + BCN_TX_MAIN_STATUS = 0; + // break; + + } + else + { + Set_BCN_TX_STATUS(BCN_TX_FAILURE); + BCN_TX_MAIN_STATUS = 0; + // break; + + } + } + } + else + { + Set_BCN_TX_STATUS(BCN_TX_DISABLED); + BCN_TX_MAIN_STATUS = 0; + // break; + + } + } + else + { + Set_BCN_TX_STATUS(BCN_RF_SILENCE); //Window of RF Silence: None of the Txs should be on. + BCN_TX_MAIN_STATUS = 0; + // break; + } +} + +void Set_BCN_TX_STATUS(uint8_t STATUS) +{ + BCN_TX_STATUS = STATUS; +} + +int check_Temperature() +{ + int temperature; + while((readreg(RF22_REG_0F_ADC_CONFIGURATION) && 0x80) == 0x0) + { + writereg(RF22_REG_0F_ADC_CONFIGURATION,128); //128 = 10000000 + writereg(RF22_REG_12_Temperature_Sensor_Calibration,32); //160 == 10100000 32 == 00100000 + wait(1); + temperature = readreg(RF22_REG_11_ADC_Value); + //pc.printf("Temperature: %d\r\n", temperature); + } + return temperature; +} + +void SHORT_BCN_TX() +{ + writereg(RF22_REG_6E_TX_DATA_RATE,0x01); + writereg(RF22_REG_6F_TX_DATA_RATE,0x4F);//160bps + writereg(RF22_REG_3E_PACKET_LENGTH,SHORT_TX_DATA); //short packet length + /* + init(); + //init complete + pc.printf("init complete.....press t to send\n"); + while(pc.getc()=='t') + { */ + //button.rise(&interrupt_func); //interrupt enabled ( rising edge of pin 9) + wait(0.02); // pl. update this value or even avoid it!!! + int i=0; + //extract values from short_beacon[] + struct Short_beacon + { + uint8_t Voltage[1]; + uint8_t AngularSpeed[2]; + uint8_t SubsystemStatus[1]; + uint8_t Temp[3]; + uint8_t ErrorFlag[1]; + }Shortbeacon = { {0x88}, {0x99, 0xAA} , {0xAA},{0xAA,0xDD,0xEE}, {0x00} }; + + //filling hk data + //uint8_t short_beacon[] = { 0xAB, 0x8A, 0xE2, 0xBB, 0xB8, 0xA2, 0x8E,Shortbeacon.Voltage[0],Shortbeacon.AngularSpeed[0], Shortbeacon.AngularSpeed[1],Shortbeacon.SubsystemStatus[0],Shortbeacon.Temp[0],Shortbeacon.Temp[1],Shortbeacon.Temp[2],Shortbeacon.ErrorFlag[0]}; + uint8_t short_beacon[] = { 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77,Shortbeacon.Voltage[0],Shortbeacon.AngularSpeed[0], Shortbeacon.AngularSpeed[1],Shortbeacon.SubsystemStatus[0],Shortbeacon.Temp[0],Shortbeacon.Temp[1],Shortbeacon.Temp[2],Shortbeacon.ErrorFlag[0]}; + + //uint8_t Short_beacon[15]; +// for(int i = 0;i<15;i++) +// { +// Long_beacon[i] = 0xAA; +// } + + //writereg(RF22_REG_07_OPERATING_MODE1,0x01); //ready mode ?? + clearTxBuf(); + //writing data first time + int byte = 0; + cs = 0; + spi.write(0xFF); + + for (int byte_counter = 0; byte_counter <15 ; i++) + { + for(int j = 3; j >= 0 ; j--) + { + if((short_beacon[byte_counter] & (uint8_t) pow(2.0,(j*2+1)))!= pow(2.0,(j*2+1))) + { + byte=0x00; + } + else + { + byte=0xF0; + } + if((short_beacon[byte_counter] & (uint8_t) pow(2.0,j*2))!= pow(2.0,j*2)) + { + byte=byte | 0x00; + } + else + { + byte=byte | 0x0F; + } + spi.write(byte); + } + } + + cs = 1; + + //Set to Tx mode + writereg(RF22_REG_07_OPERATING_MODE1,0x09); + + //Check for fifoThresh + while((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x20) != 0x20); + //pc.printf("fifothresh1?\n"); + + //rf22.waitPacketSent(); + while((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x04) != 0x04); + //pc.printf(" chk pkt sent!\r\n"); + pc.printf("Short packet sent\r\n"); +} +void LONG_BCN_TX() +{ + writereg(RF22_REG_6E_TX_DATA_RATE,0x04); + writereg(RF22_REG_6F_TX_DATA_RATE,0xea); + writereg(RF22_REG_3E_PACKET_LENGTH,LONG_TX_DATA); //long packet length + wait(0.02); // pl. update this value or even avoid it!!! + //extract values from long_beacon[] + + //uint8_t Long_beacon[] = { 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77,Longbeacon.Voltage[0],Longbeacon.AngularSpeed[0], Longbeacon.AngularSpeed[1],Longbeacon.SubsystemStatus[0],Longbeacon.Temp[0],Longbeacon.Temp[1],Longbeacon.Temp[2],Longbeacon.ErrorFlag[0]}; + + uint8_t Long_beacon[75]; + for(int i = 0;i<75;i++) + { + Long_beacon[i] = 0xA0; + } + + //setModeIdle(); + writereg(RF22_REG_07_OPERATING_MODE1,0x01); //ready mode + clearTxBuf(); + //writing data first time + cs = 0; + spi.write(0xFF); + for(int i=0; i<60;i++) + { + spi.write(Long_beacon[i]); + } + cs = 1; + + //Set to Tx mode + writereg(RF22_REG_07_OPERATING_MODE1,0x09); + + //Check for fifoThresh + while((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x20) != 0x20); + //pc.printf("fifothresh1?\n"); + //writing data first time + cs = 0; + spi.write(0xFF); + for(int i=60; i<75;i++) + { + spi.write(Long_beacon[i]); + } + cs = 1; + wait(0.01); + //Check for fifoThresh + while((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x20) != 0x20); + //pc.printf("fifothresh2?\n"); + //rf22.waitPacketSent(); + while((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x04) != 0x04); + //pc.printf(" chk pkt sent!]\r\n"); + pc.printf("Long packet sent\r\n"); +} + +void writereg(uint8_t reg,uint8_t val) +{ + cs = 0;__disable_irq();spi.write(reg | 0x80);spi.write(val);__enable_irq();cs = 1; +} +uint8_t readreg(uint8_t reg) +{ + int val;cs = 0;__disable_irq();spi.write(reg & ~0x80);val = spi.write(0);__enable_irq();cs = 1;return val; +} +void clearTxBuf() +{ + writereg(RF22_REG_08_OPERATING_MODE2,0x01); + writereg(RF22_REG_08_OPERATING_MODE2,0x00); +} +void clearRxBuf() +{ + writereg(RF22_REG_08_OPERATING_MODE2,0x02); + writereg(RF22_REG_08_OPERATING_MODE2,0x00); +} +int setFrequency(float centre,float afcPullInRange) +{ + //freq setting begins + uint8_t fbsel = 0x40; + uint8_t afclimiter; + if (centre >= 480.0) + { + centre /= 2; + fbsel |= 0x20; + afclimiter = afcPullInRange * 1000000.0 / 1250.0; + } + else + { + if (afcPullInRange < 0.0 || afcPullInRange > 0.159375) + return false; + afclimiter = afcPullInRange * 1000000.0 / 625.0; + } + centre /= 10.0; + float integerPart = floor(centre); + float fractionalPart = centre - integerPart; + + uint8_t fb = (uint8_t)integerPart - 24; // Range 0 to 23 + fbsel |= fb; + uint16_t fc = fractionalPart * 64000; + writereg(RF22_REG_73_FREQUENCY_OFFSET1, 0); // REVISIT + writereg(RF22_REG_74_FREQUENCY_OFFSET2, 0); + writereg(RF22_REG_75_FREQUENCY_BAND_SELECT, fbsel); + writereg(RF22_REG_76_NOMINAL_CARRIER_FREQUENCY1, fc >> 8); + writereg(RF22_REG_77_NOMINAL_CARRIER_FREQUENCY0, fc & 0xff); + writereg(RF22_REG_2A_AFC_LIMITER, afclimiter); + return 0; +} + +void Init_BEACON_HW() +{ + cs=1; // chip must be deselected + //wait(1); //change the time later + spi.format(8,0); + spi.frequency(10000000); //10MHz SCLK + + //should either have a flag for invalid SPI or discard this for actual case or add reset + if (readreg(RF22_REG_00_DEVICE_TYPE) == 0x08) + pc.printf("spi connection valid\r\n"); + else + pc.printf("error in spi connection\r\n"); + //reset() + + + writereg(RF22_REG_07_OPERATING_MODE1,0x80); //sw_reset + wait(1); //takes time to reset + + clearTxBuf(); + + clearRxBuf();//may not be required + + //txfifoalmostempty + writereg(RF22_REG_7D_TX_FIFO_CONTROL2,10); + + //Packet-engine registers + writereg(RF22_REG_30_DATA_ACCESS_CONTROL,0x00); //RF22_REG_30_DATA_ACCESS_CONTROL, RF22_ENPACRX | RF22_ENPACTX | RF22_ENCRC | RF22_CRC_CRC_16_IBM + //&0x77 = diasable packet rx-tx handling + + writereg(RF22_REG_33_HEADER_CONTROL2,0x08); //RF22_REG_33_HEADER_CONTROL2, RF22_HDLEN_4 | RF22_SYNCLEN_2 + writereg(RF22_REG_34_PREAMBLE_LENGTH,0x00); //RF22_REG_34_PREAMBLE_LENGTH, nibbles); preamble length = 8; + //may be redundant since packethandler is disabled + + writereg(RF22_REG_0B_GPIO_CONFIGURATION0,0x15); // TX state ?? + writereg(RF22_REG_0C_GPIO_CONFIGURATION1,0x12); // RX state ?? + + //interrupts + // spiWrite(RF22_REG_05_INTERRUPT_ENABLE1, RF22_ENTXFFAEM |RF22_ENRXFFAFULL | RF22_ENPKSENT |RF22_ENPKVALID| RF22_ENCRCERROR); + // spiWrite(RF22_REG_06_INTERRUPT_ENABLE2, RF22_ENPREAVAL); + + setFrequency(435.0, 0.05); + + //This may not be required + if((readreg(RF22_REG_02_DEVICE_STATUS)& 0x08)!= 0x00) + pc.printf("frequency not set properly\r\n"); + //frequency set + + //setModemConfig(FSK_Rb2_4Fd36); FSK_Rb2_4Fd36, ///< FSK, No Manchester, Rb = 2.4kbs, Fd = 36kHz + //setmodemregisters + //0x1b, 0x03, 0x41, 0x60, 0x27, 0x52, 0x00, 0x07, 0x40, 0x0a, 0x1e, 0x80, 0x60, 0x13, 0xa9, 0x2c, 0x22, 0x3a = FSK_RB2_4FD36 + //0xc8, 0x03, 0x39, 0x20, 0x68, 0xdc, 0x00, 0x6b, 0x2a, 0x08, 0x2a, 0x80, 0x60, 0x13, 0xa9, 0x2c, 0x21, 0x08 = OOK,2.4, 335 + writereg(RF22_REG_1C_IF_FILTER_BANDWIDTH,0xdf); + writereg(RF22_REG_1F_CLOCK_RECOVERY_GEARSHIFT_OVERRIDE,0x03); + writereg(RF22_REG_20_CLOCK_RECOVERY_OVERSAMPLING_RATE,0x39); + writereg(RF22_REG_21_CLOCK_RECOVERY_OFFSET2,0x20); + writereg(RF22_REG_22_CLOCK_RECOVERY_OFFSET1,0x68); //updated 20 to 25 reg values from excel sheet for 1.2 Khz freq. deviation,fsk + writereg(RF22_REG_23_CLOCK_RECOVERY_OFFSET0,0xdc); + writereg(RF22_REG_24_CLOCK_RECOVERY_TIMING_LOOP_GAIN1,0x00); + writereg(RF22_REG_25_CLOCK_RECOVERY_TIMING_LOOP_GAIN0,0x6B); + writereg(RF22_REG_2C_OOK_COUNTER_VALUE_1,0x2C); + writereg(RF22_REG_2D_OOK_COUNTER_VALUE_2,0x11); //not required for fsk (OOK counter value) + writereg(RF22_REG_2E_SLICER_PEAK_HOLD,0x2A); //?? + writereg(RF22_REG_58,0x80); + writereg(RF22_REG_69_AGC_OVERRIDE1,0x60); + + + //writereg(RF22_REG_6E_TX_DATA_RATE_0.125_1,0x09);//written later + //writereg(RF22_REG_6F_TX_DATA_RATE_0.125_0,0xd5);//written later + + writereg(RF22_REG_70_MODULATION_CONTROL1,0x20);//changed from 0x2c to 0x20 since machester is not required + writereg(RF22_REG_71_MODULATION_CONTROL2,0x21);//ook = 0x21 //fsk = 0x22 + + //writereg(RF22_REG_72_FREQUENCY_DEVIATION,0x50); + //required for OOK??? + + //set tx power + writereg(RF22_REG_6D_TX_POWER,0x07); //20dbm + //why 0x06?? 0x07 is for max//is the previous bits required? + + //writereg(RF22_REG_3E_PACKET_LENGTH,SHORT_TX_DATA); //short packet length //written later +} +bool Check_ACK_RECEIVED() +{ + //logic: + if((readreg(RF22_REG_03_INTERRUPT_STATUS1) & 0x04) == 0x04) //bit is set if the data packet is sent correctly + { + printf("Packet sent: ACK received\r\n"); + return 1; //for ACK received: yes + + } + else + { + pc.printf("Packet not sent\r\n"); + return 0; //actual value + //return 1; //to make this function work in any condition //Why?? + + } +} +int main() +{ + //int temp, final_temp; + + P_BCN_INIT(); + + t.start(); + + loop.attach(&P_BCN_TX_MAIN, 30.0); + + while (t.read() < RF_SILENCE_TIME); + + P_BCN_FEN(); + + t.stop(); +// temp = check_Temperature(); +// final_temp = (float)temp*0.5 - 64; +// pc.printf("%d\r\n", final_temp); + + //while(1) +// { +// temp = check_Temperature(); +// final_temp = (float)temp*0.5 - 64; +// pc.printf("Temperature: %d\r\n", final_temp); +// wait(900); //15 minutes +// } + while(1) + { + + pc.printf("%d\n",BCN_TS_BUFFER); + //display statuses or wait + + //BCN_INIT_STATUS + //BCN_TX_MAIN_STATUS + //BCN_TX_STATUS + //BCN_TX_EN + //BCN_FEN + //BCN_STANDBY + } + +} \ No newline at end of file