mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_rcc.c
- Revision:
- 205:c41fc65bcfb4
- Child:
- 218:44081b78fdc2
diff -r 92d082577917 -r c41fc65bcfb4 targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_rcc.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_rcc.c Thu May 22 20:00:09 2014 +0100 @@ -0,0 +1,601 @@ +/** + ****************************************************************************** + * @file stm32f0xx_hal_rcc.c + * @author MCD Application Team + * @version V1.0.0 + * @date 20-May-2014 + * @brief RCC HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the Reset and Clock Control (RCC) peripheral: + * + Initialization/de-initialization function + * + Peripheral Control function + * + @verbatim + ============================================================================== + ##### RCC specific features ##### + ============================================================================== + [..] + After reset the device is running from Internal High Speed oscillator + (HSI 8MHz) with Flash 0 wait state, Flash prefetch buffer is disabled, + and all peripherals are off except internal SRAM, Flash and JTAG. + (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses; + all peripherals mapped on these busses are running at HSI speed. + (+) The clock for all peripherals is switched off, except the SRAM and FLASH. + (+) All GPIOs are in input floating state, except the JTAG pins which + are assigned to be used for debug purpose. + + [..] + Once the device started from reset, the user application has to: + (+) Configure the clock source to be used to drive the System clock + (if the application needs higher frequency/performance) + (+) Configure the System clock frequency and Flash settings + (+) Configure the AHB and APB busses prescalers + (+) Enable the clock for the peripheral(s) to be used + (+) Configure the clock source(s) for peripherals which clocks are not + derived from the System clock (RTC, ADC, I2C, USART, TIM, USB FS, etc..) + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx_hal.h" + +/** @addtogroup STM32F0xx_HAL_Driver + * @{ + */ + +/** @defgroup RCC + * @brief RCC HAL module driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define RCC_CFGR_HPRE_BITNUMBER 4 +#define RCC_CFGR_PPRE_BITNUMBER 8 + +/* Private macro -------------------------------------------------------------*/ +#define __MCO_CLK_ENABLE() __GPIOA_CLK_ENABLE() +#define MCO_GPIO_PORT GPIOA +#define MCO_PIN GPIO_PIN_8 + +/* Private variables ---------------------------------------------------------*/ +const uint8_t APBAHBPrescTable[16] = {0, 0, 0, 0, 1, 2, 3, 4, 1, 2, 3, 4, 6, 7, 8, 9}; + +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup RCC_Private_Functions + * @{ + */ + +/** @defgroup HAL_RCC_Group1 Initialization/de-initialization function + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization function ##### + =============================================================================== + [..] + This section provide functions allowing to configure the internal/external oscillators + (HSE, HSI, HSI14, HSI48, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, + AHB and APB1). + + [..] Internal/external clock and PLL configuration + (#) HSI (high-speed internal), 8 MHz factory-trimmed RC used directly or through + the PLL as System clock source. + The HSI clock can be used also to clock the USART and I2C peripherals. + + (#) HSI14 (high-speed internal), 14 MHz factory-trimmed RC used directly to clock + the ADC peripheral. + + (#) LSI (low-speed internal), 40 KHz low consumption RC used as IWDG and/or RTC + clock source. + + (#) HSE (high-speed external), 4 to 32 MHz crystal oscillator used directly or + through the PLL as System clock source. Can be used also as RTC clock source. + + (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. + + (#) PLL (clocked by HSI, HSI48 or HSE), featuring different output clocks: + (+@) The first output is used to generate the high speed system clock (up to 48 MHz) + (+@) The second output is used to generate the clock for the USB FS (48 MHz) + (+@) The third output may be used to generate the clock for the TIM, I2C and USART + peripherals (up to 48 MHz) + + (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() + and if a HSE clock failure occurs(HSE used directly or through PLL as System + clock source), the System clockis automatically switched to HSI and an interrupt + is generated if enabled. The interrupt is linked to the Cortex-M0 NMI + (Non-Maskable Interrupt) exception vector. + + (#) MCO (microcontroller clock output), used to output SYSCLK, HSI, HSE, LSI, LSE or PLL + clock (divided by 2) output on pin (such as PA8 pin). + + [..] System, AHB and APB busses clocks configuration + (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, + HSE and PLL. + The AHB clock (HCLK) is derived from System clock through configurable + prescaler and used to clock the CPU, memory and peripherals mapped + on AHB bus (DMA, GPIO...). APB1 (PCLK1) clock is derived + from AHB clock through configurable prescalers and used to clock + the peripherals mapped on these busses. You can use + "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. + + (#) All the peripheral clocks are derived from the System clock (SYSCLK) except: + (+@) The FLASH program/erase clock which is always HSI 8MHz clock. + (+@) The USB 48 MHz clock which is derived from the PLL VCO clock. + (+@) The USART clock which can be derived as well from HSI 8MHz, LSI or LSE. + (+@) The I2C clock which can be derived as well from HSI 8MHz clock. + (+@) The ADC clock which is derived from PLL output. + (+@) The RTC clock which is derived from the LSE, LSI or 1 MHz HSE_RTC + (HSE divided by a programmable prescaler). The System clock (SYSCLK) + frequency must be higher or equal to the RTC clock frequency. + (+@) IWDG clock which is always the LSI clock. + + (#) For the STM32F0xx devices, the maximum frequency of the SYSCLK, HCLK and PCLK1 is 48 MHz, + Depending on the SYSCLK frequency, the flash latency should be adapted accordingly: + +-----------------------------------------------+ + | Latency | SYSCLK clock frequency (MHz) | + |---------------|-------------------------------| + |0WS(1CPU cycle)| 0 < SYSCLK <= 24 | + |---------------|-------------------------------| + |1WS(2CPU cycle)| 24 < SYSCLK <= 48 | + +-----------------------------------------------+ + + (#) After reset, the System clock source is the HSI (8 MHz) with 0 WS and + prefetch is disabled. + +@endverbatim + * @{ + */ + +/** + * @brief Resets the RCC clock configuration to the default reset state. + * @note The default reset state of the clock configuration is given below: + * - HSI ON and used as system clock source + * - HSE and PLL OFF + * - AHB, APB1 prescaler set to 1. + * - CSS, MCO OFF + * - All interrupts disabled + * @note This function doesn't modify the configuration of the + * - Peripheral clocks + * - LSI, LSE and RTC clocks + * @param None + * @retval None + */ +void HAL_RCC_DeInit(void) +{ + /* Set HSION bit, HSITRIM[4:0] bits to the reset value*/ + SET_BIT(RCC->CR, RCC_CR_HSION | RCC_CR_HSITRIM_4); + + /* Reset SW[1:0], HPRE[3:0], PPRE[2:0] and MCOSEL[2:0] bits */ + CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW | RCC_CFGR_HPRE | RCC_CFGR_PPRE | RCC_CFGR_MCO); + + /* Reset HSEON, CSSON, PLLON bits */ + CLEAR_BIT(RCC->CR, RCC_CR_PLLON | RCC_CR_CSSON | RCC_CR_HSEON); + + /* Reset HSEBYP bit */ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); + + /* Reset CFGR register */ + CLEAR_REG(RCC->CFGR); + + /* Reset CFGR2 register */ + CLEAR_REG(RCC->CFGR2); + + /* Reset CFGR3 register */ + CLEAR_REG(RCC->CFGR3); + + /* Disable all interrupts */ + CLEAR_REG(RCC->CIR); +} + +/** + * @brief Initializes the RCC Oscillators according to the specified parameters in the + * RCC_OscInitTypeDef. + * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC Oscillators. + * @note The PLL is not disabled when used as system clock. + * @retval HAL status + */ +__weak HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + /* Note : This function is defined into this file for library reference. */ + /* Function content is located into file stm32f0xx_hal_rcc_ex.c to */ + /* handle the possible oscillators present in STM32F0xx devices */ + + /* Return error status as not implemented here */ + return HAL_ERROR; +} + +/** + * @brief Initializes the CPU, AHB and APB busses clocks according to the specified + * parameters in the RCC_ClkInitStruct. + * @param RCC_ClkInitStruct: pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC peripheral. + * @param FLatency: FLASH Latency + * This parameter can be one of the following values: + * @arg FLASH_LATENCY_0: FLASH 0 Latency cycle + * @arg FLASH_LATENCY_1: FLASH 1 Latency cycle + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated by HAL_RCC_GetHCLKFreq() function called within this function + * + * @note The HSI is used (enabled by hardware) as system clock source after + * startup from Reset, wake-up from STOP and STANDBY mode, or in case + * of failure of the HSE used directly or indirectly as system clock + * (if the Clock Security System CSS is enabled). + * + * @note A switch from one clock source to another occurs only if the target + * clock source is ready (clock stable after startup delay or PLL locked). + * If a clock source which is not yet ready is selected, the switch will + * occur when the clock source will be ready. + * @retval HAL status + */ +__weak HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency) +{ + /* Note : This function is defined into this file for library reference. */ + /* Function content is located into file stm32f0xx_hal_rcc_ex.c to */ + /* handle the possible oscillators present in STM32F0xx devices */ + + /* Return error status as not implemented here */ + return HAL_ERROR; +} + +/** + * @} + */ + +/** @defgroup HAL_RCC_Group2 Peripheral Control function + * @brief RCC clocks control functions + * +@verbatim + =============================================================================== + ##### Peripheral Control function ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + +@endverbatim + * @{ + */ + +/** + * @brief Selects the clock source to output on MCO pin(such as PA8). + * @note MCO pin (such as PA8) should be configured in alternate function mode. + * @param RCC_MCOx: specifies the output direction for the clock source. + * This parameter can be one of the following values: + * @arg RCC_MCO: Clock source to output on MCO pin(such as PA8). + * @param RCC_MCOSource: specifies the clock source to output. + * This parameter can be one of the following values: + * @arg RCC_MCOSOURCE_LSI: LSI clock selected as MCO source + * @arg RCC_MCOSOURCE_HSI: HSI clock selected as MCO source + * @arg RCC_MCOSOURCE_LSE: LSE clock selected as MCO source + * @arg RCC_MCOSOURCE_HSE: HSE clock selected as MCO source + * @arg RCC_MCOSOURCE_PLLCLK_NODIV: main PLL clock not divided selected as MCO source (not applicable to STM32F05x devices) + * @arg RCC_MCOSOURCE_PLLCLK_DIV2: main PLL clock divided by 2 selected as MCO source + * @arg RCC_MCOSOURCE_SYSCLK: System clock (SYSCLK) selected as MCO source + * @param RCC_MCODiv: specifies the MCOx prescaler. + * This parameter can be one of the following values: + * @arg RCC_MCO_NODIV: no division applied to MCO clock + * @retval None + */ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) +{ + GPIO_InitTypeDef gpio; + /* Check the parameters */ + assert_param(IS_RCC_MCO(RCC_MCOx)); + assert_param(IS_RCC_MCODIV(RCC_MCODiv)); + /* RCC_MCO */ + assert_param(IS_RCC_MCOSOURCE(RCC_MCOSource)); + + /* MCO Clock Enable */ + __MCO_CLK_ENABLE(); + + /* Configue the MCO pin in alternate function mode */ + gpio.Pin = MCO_PIN; + gpio.Mode = GPIO_MODE_AF_PP; + gpio.Speed = GPIO_SPEED_HIGH; + gpio.Pull = GPIO_NOPULL; + gpio.Alternate = GPIO_AF0_MCO; + HAL_GPIO_Init(MCO_GPIO_PORT, &gpio); + + /* Configure the MCO clock source */ + __HAL_RCC_MCO_CONFIG(RCC_MCOSource, RCC_MCODiv); +} + +/** + * @brief Enables the Clock Security System. + * @note If a failure is detected on the HSE oscillator clock, this oscillator + * is automatically disabled and an interrupt is generated to inform the + * software about the failure (Clock Security System Interrupt, CSSI), + * allowing the MCU to perform rescue operations. The CSSI is linked to + * the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector. + * @param None + * @retval None + */ +void HAL_RCC_EnableCSS(void) +{ + SET_BIT(RCC->CR, RCC_CR_CSSON); +} + +/** + * @brief Disables the Clock Security System. + * @param None + * @retval None + */ +void HAL_RCC_DisableCSS(void) +{ + CLEAR_BIT(RCC->CR, RCC_CR_CSSON); +} + +/** + * @brief Returns the SYSCLK frequency + * @note The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * @note If SYSCLK source is HSI, function returns a value based on HSI_VALUE(*) + * @note If SYSCLK source is HSI48, function returns a value based on HSI48_VALUE(*) + * @note If SYSCLK source is HSE, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) + * @note If SYSCLK source is PLL, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) or depending on STM32F0xx devices either a value based + * on HSI_VALUE divided by 2 or HSI_VALUE divided by PREDIV factor(*) multiplied by the + * PLL factor . + * @note (*) HSI_VALUE & HSI48_VALUE are constants defined in stm32f0xx_hal_conf.h file + * (default values 8 MHz and 48MHz). + * @note (**) HSE_VALUE is a constant defined in stm32f0xx_hal_conf.h file (default value + * 8 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * @note The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @note This function can be used by the user application to compute the + * baudrate for the communication peripherals or configure other parameters. + * + * @note Each time SYSCLK changes, this function must be called to update the + * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @param None + * @retval SYSCLK frequency + */ +__weak uint32_t HAL_RCC_GetSysClockFreq(void) +{ + /* Note : This function is defined into this file for library reference. */ + /* Function content is located into file stm32f0xx_hal_rcc_ex.c to */ + /* handle the possible oscillators present in STM32F0xx devices */ + + /* Return current SYSCLK frequency without computation */ + return SystemCoreClock; +} + +/** + * @brief Returns the HCLK frequency + * @note Each time HCLK changes, this function must be called to update the + * right HCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated within this function + * + * @param None + * @retval HCLK frequency + */ +uint32_t HAL_RCC_GetHCLKFreq(void) +{ + SystemCoreClock = HAL_RCC_GetSysClockFreq() >> APBAHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_BITNUMBER]; + return SystemCoreClock; +} + +/** + * @brief Returns the PCLK1 frequency + * @note Each time PCLK1 changes, this function must be called to update the + * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. + * @param None + * @retval PCLK1 frequency + */ +uint32_t HAL_RCC_GetPCLK1Freq(void) +{ + /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq() >> APBAHBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE)>> RCC_CFGR_PPRE_BITNUMBER]); +} + +/** + * @brief Configures the RCC_OscInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that + * will be configured. + * @retval None + */ +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + /* Set all possible values for the Oscillator type parameter ---------------*/ + RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; + + /* Get the HSE configuration -----------------------------------------------*/ + if((RCC->CR & RCC_CR_HSEBYP) == RCC_CR_HSEBYP) + { + RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; + } + else if((RCC->CR & RCC_CR_HSEON) == RCC_CR_HSEON) + { + RCC_OscInitStruct->HSEState = RCC_HSE_ON; + } + else + { + RCC_OscInitStruct->HSEState = RCC_HSE_OFF; + } + + /* Get the HSI configuration -----------------------------------------------*/ + if((RCC->CR & RCC_CR_HSION) == RCC_CR_HSION) + { + RCC_OscInitStruct->HSIState = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSIState = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR &RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_BitNumber); + + /* Get the LSE configuration -----------------------------------------------*/ + if((RCC->BDCR & RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) + { + RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; + } + else if((RCC->BDCR & RCC_BDCR_LSEON) == RCC_BDCR_LSEON) + { + RCC_OscInitStruct->LSEState = RCC_LSE_ON; + } + else + { + RCC_OscInitStruct->LSEState = RCC_LSE_OFF; + } + + /* Get the LSI configuration -----------------------------------------------*/ + if((RCC->CSR & RCC_CSR_LSION) == RCC_CSR_LSION) + { + RCC_OscInitStruct->LSIState = RCC_LSI_ON; + } + else + { + RCC_OscInitStruct->LSIState = RCC_LSI_OFF; + } + + /* Get the PLL configuration -----------------------------------------------*/ + if((RCC->CR & RCC_CR_PLLON) == RCC_CR_PLLON) + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; + } + else + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; + } + RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC); + RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMUL); + RCC_OscInitStruct->PLL.PREDIV = (uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV); + + /* Get the HSI14 configuration -----------------------------------------------*/ + if((RCC->CR2 & RCC_CR2_HSI14ON) == RCC_CR2_HSI14ON) + { + RCC_OscInitStruct->HSI14State = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSI14State = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSI14CalibrationValue = (uint32_t)((RCC->CR2 & RCC_CR2_HSI14TRIM) >> RCC_CR2_HSI14TRIM_BitNumber); + + /* Get the HSI48 configuration if any-----------------------------------------*/ + RCC_OscInitStruct->HSI48State = __HAL_RCC_GET_HSI48_STATE(); +} + +/** + * @brief Get the RCC_ClkInitStruct according to the internal + * RCC configuration registers. + * @param RCC_ClkInitStruct: pointer to an RCC_ClkInitTypeDef structure that + * contains the current clock configuration. + * @param pFLatency: Pointer on the Flash Latency. + * @retval None + */ +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency) +{ + /* Set all possible values for the Clock type parameter --------------------*/ + RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1; + + /* Get the SYSCLK configuration --------------------------------------------*/ + RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); + + /* Get the HCLK configuration ----------------------------------------------*/ + RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); + + /* Get the APB1 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE); + + /* Get the Flash Wait State (Latency) configuration ------------------------*/ + *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); +} + +/** + * @brief This function handles the RCC CSS interrupt request. + * @note This API should be called under the NMI_Handler(). + * @param None + * @retval None + */ +void HAL_RCC_NMI_IRQHandler(void) +{ + /* Check RCC CSSF flag */ + if(__HAL_RCC_GET_IT(RCC_IT_CSS)) + { + /* RCC Clock Security System interrupt user callback */ + HAL_RCC_CCSCallback(); + + /* Clear RCC CSS pending bit */ + __HAL_RCC_CLEAR_IT(RCC_IT_CSS); + } +} + +/** + * @brief RCC Clock Security System interrupt callback + * @param none + * @retval none + */ +__weak void HAL_RCC_CCSCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RCC_CCSCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/