mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/hal/TARGET_NXP/TARGET_LPC176X/TARGET_UBLOX_C027/PinNames.h
- Revision:
- 79:6fdc4ea80ae0
- Child:
- 114:826c6eb78fdc
diff -r 2cab419ff388 -r 6fdc4ea80ae0 targets/hal/TARGET_NXP/TARGET_LPC176X/TARGET_UBLOX_C027/PinNames.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/hal/TARGET_NXP/TARGET_LPC176X/TARGET_UBLOX_C027/PinNames.h Thu Jan 30 09:45:05 2014 +0000 @@ -0,0 +1,188 @@ +/* mbed Microcontroller Library + * Copyright (c) 2006-2013 ARM Limited + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#ifndef MBED_PINNAMES_H +#define MBED_PINNAMES_H + +#include "cmsis.h" + +#ifdef __cplusplus +extern "C" { +#endif + +typedef enum { + PIN_INPUT, + PIN_OUTPUT +} PinDirection; + +#define PORT_SHIFT 5 + +typedef enum { + // LPC Pin Names + P0_0 = LPC_GPIO0_BASE, + P0_1, P0_2, P0_3, P0_4, P0_5, P0_6, P0_7, P0_8, P0_9, P0_10, P0_11, P0_12, P0_13, P0_14, P0_15, P0_16, P0_17, P0_18, P0_19, P0_20, P0_21, P0_22, P0_23, P0_24, P0_25, P0_26, P0_27, P0_28, P0_29, P0_30, P0_31, + P1_0, P1_1, P1_2, P1_3, P1_4, P1_5, P1_6, P1_7, P1_8, P1_9, P1_10, P1_11, P1_12, P1_13, P1_14, P1_15, P1_16, P1_17, P1_18, P1_19, P1_20, P1_21, P1_22, P1_23, P1_24, P1_25, P1_26, P1_27, P1_28, P1_29, P1_30, P1_31, + P2_0, P2_1, P2_2, P2_3, P2_4, P2_5, P2_6, P2_7, P2_8, P2_9, P2_10, P2_11, P2_12, P2_13, P2_14, P2_15, P2_16, P2_17, P2_18, P2_19, P2_20, P2_21, P2_22, P2_23, P2_24, P2_25, P2_26, P2_27, P2_28, P2_29, P2_30, P2_31, + P3_0, P3_1, P3_2, P3_3, P3_4, P3_5, P3_6, P3_7, P3_8, P3_9, P3_10, P3_11, P3_12, P3_13, P3_14, P3_15, P3_16, P3_17, P3_18, P3_19, P3_20, P3_21, P3_22, P3_23, P3_24, P3_25, P3_26, P3_27, P3_28, P3_29, P3_30, P3_31, + P4_0, P4_1, P4_2, P4_3, P4_4, P4_5, P4_6, P4_7, P4_8, P4_9, P4_10, P4_11, P4_12, P4_13, P4_14, P4_15, P4_16, P4_17, P4_18, P4_19, P4_20, P4_21, P4_22, P4_23, P4_24, P4_25, P4_26, P4_27, P4_28, P4_29, P4_30, P4_31, + + // Arduino Pin Names + + // PIN header connector + // for standard-based form factor with expansion board + // ----------------------------------------------------------- + // PMW = Pulswidth Modulator + // EINT = External Interrupt + // AOUT = Analog Output + + // Analog Ports (A0-A5) + A0 = P0_23, // I2S_CLK + A1 = P0_24, // I2S_WS + A2 = P0_25, // I2S_SDA + A3 = P0_26, // AOUT + A4 = P1_30, // + A5 = P1_31, // + // Digital Port (D0-D7) + D0 = P4_29, // TXD + D1 = P4_28, // RXD + D2 = P2_13, // EINT + D3 = P2_0, // PWM + D4 = P2_12, // EINT + D5 = P2_1, // PWM + D6 = P2_2, // PWM + D7 = P2_11, // EINT + // Digital Port (D8-D13) + D8 = P2_4, // PWM + D9 = P2_3, // PWM + D10 = P1_21, // PWM SSEL + D11 = P1_24, // PWM MOSI + D12 = P1_23, // PWM MISO + D13 = P1_20, // PWM SCK + // GND + // AREF + SDA = P0_0, + D14 = SDA, + SCL = P0_1, + D15 = SCL, + + // I2C (shared with LISA/SARA) + GPSSDA = P0_27, + GPSSCL = P0_28, + // UART + GPSTXD = P0_10, + GPSRXD = P0_11, + // Control + GPSRST = P1_18, // Reset (input to GPS, active low) + GPSPPS = P1_19, // 1PPS Timepulse (output from GPS) + GPSINT = P1_22, // Interrupt (input to GPS) + GPSEN = P1_29, // Supply Control (high = enabled) + + // u-blox LISA/SARA cellular modem + // http://www.u-blox.com/wireless-modules.html + // ----------------------------------------------------------- + // UART (LPC1768 = DTE, LISA/SARA = DCE) + MDMTXD = P0_15, // Transmit Data + MDMRXD = P0_16, // Receive Data + MDMCTS = P0_17, // Clear to Send + MDMDCD = P0_18, // Data Carrier Detect + MDMDSR = P0_19, // Data Set Ready + MDMDTR = P0_20, // Data Terminal Ready (set high or use handshake) + MDMRI = P0_21, // Ring Indicator + MDMRTS = P0_22, // Request to Send (set high or use handshake) + + // USB (not available on C27-G35) + MDMUSBDP = P0_29, // USB D+ + MDMUSBDN = P0_30, // USB D- + MDMUSBCON = P2_9, // USB Connect + MDMUSBDET = P0_7, // USB Detect (n/a on REV.A board) + // Control + MDMEN = P2_5, // Supply Control (high = enabled) + MDMPWRON = P2_6, // + MDMGPIO1 = P2_7, // GPIO1, Network status + MDMRST = P2_8, // Reset (active low, set as open drain!) + MDMLVLOE = P0_9, // Serial/GPIO Level Shifter Output Enable (n/a on REV.A board) + MDMILVLOE = P0_8, // I2C Level Shifter Output Enable (n/a on REV.A board) + + // CAN (TJA1040) + // ----------------------------------------------------------- + CANRD = P0_4, + CANTD = P0_5, + CANS = P0_6, // standby (low=normal, high=standby/rxonly) + + // Ethernet (DP83848) + // ----------------------------------------------------------- + ETHTXD0 = P1_0, + ETHTXD1 = P1_1, + ETHTXEN = P1_4, + ETHCRS = P1_8, + ETHRXD0 = P1_9, + ETHRXD1 = P1_10, + ETHRXEN = P1_14, + ETHREFCLK = P1_15, + ETHMDC = P1_16, + ETHMDIO = P1_17, + ETHOSCEN = P1_27, + ETHRST = P1_28, + ETHLINK = P1_25, // LED_LINK + ETHSPEED = P1_26, // LED_SPEED + + // ISP port + // ----------------------------------------------------------- + ISP = P2_10, + + // Other mbed Pin Names + LED = P3_25, + LED1 = LED, + LED_RED = LED, + + // mbed / debug IF (LPC11) + // ----------------------------------------------------------- + // Serial Port + USBTX = P0_2, + USBRX = P0_3, + USBTXD = USBTX, // identical USBTX + USBRXD = USBRX, // identical USBRX + + // Not connected + NC = (int)0xFFFFFFFF +} PinName; + +typedef enum { + PullUp = 0, + PullDown = 3, + PullNone = 2, + OpenDrain = 4 +} PinMode; + +// version of PINCON_TypeDef using register arrays +typedef struct { + __IO uint32_t PINSEL[11]; + uint32_t RESERVED0[5]; + __IO uint32_t PINMODE[10]; + __IO uint32_t PINMODE_OD[5]; +} PINCONARRAY_TypeDef; + +#define PINCONARRAY ((PINCONARRAY_TypeDef *)LPC_PINCON_BASE) + +//Additional C027 stuff +#define GPSADR (66<<1) // GPS I2C Address +#define GPSBAUD 9600 // Default GPS Baud Rate +#define MDMBAUD 115200 // Default Modem Baud Rate + +#ifdef __cplusplus +} +#endif + +#endif