mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/hal/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_K64F/device/MK64F12/MK64F12_sdhc.h
- Revision:
- 149:1fb5f62b92bd
- Parent:
- 146:f64d43ff0c18
diff -r 213f3ebbe634 -r 1fb5f62b92bd targets/hal/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_K64F/device/MK64F12/MK64F12_sdhc.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/hal/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_K64F/device/MK64F12/MK64F12_sdhc.h Thu Apr 03 11:45:06 2014 +0100 @@ -0,0 +1,5761 @@ +/* + * Copyright (c) 2014, Freescale Semiconductor, Inc. + * All rights reserved. + * + * THIS SOFTWARE IS PROVIDED BY FREESCALE "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT + * SHALL FREESCALE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, + * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT + * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY + * OF SUCH DAMAGE. + */ +/* + * WARNING! DO NOT EDIT THIS FILE DIRECTLY! + * + * This file was generated automatically and any changes may be lost. + */ +#ifndef __HW_SDHC_REGISTERS_H__ +#define __HW_SDHC_REGISTERS_H__ + +#include "regs.h" + +/* + * MK64F12 SDHC + * + * Secured Digital Host Controller + * + * Registers defined in this header file: + * - HW_SDHC_DSADDR - DMA System Address register + * - HW_SDHC_BLKATTR - Block Attributes register + * - HW_SDHC_CMDARG - Command Argument register + * - HW_SDHC_XFERTYP - Transfer Type register + * - HW_SDHC_CMDRSP0 - Command Response 0 + * - HW_SDHC_CMDRSP1 - Command Response 1 + * - HW_SDHC_CMDRSP2 - Command Response 2 + * - HW_SDHC_CMDRSP3 - Command Response 3 + * - HW_SDHC_DATPORT - Buffer Data Port register + * - HW_SDHC_PRSSTAT - Present State register + * - HW_SDHC_PROCTL - Protocol Control register + * - HW_SDHC_SYSCTL - System Control register + * - HW_SDHC_IRQSTAT - Interrupt Status register + * - HW_SDHC_IRQSTATEN - Interrupt Status Enable register + * - HW_SDHC_IRQSIGEN - Interrupt Signal Enable register + * - HW_SDHC_AC12ERR - Auto CMD12 Error Status Register + * - HW_SDHC_HTCAPBLT - Host Controller Capabilities + * - HW_SDHC_WML - Watermark Level Register + * - HW_SDHC_FEVT - Force Event register + * - HW_SDHC_ADMAES - ADMA Error Status register + * - HW_SDHC_ADSADDR - ADMA System Addressregister + * - HW_SDHC_VENDOR - Vendor Specific register + * - HW_SDHC_MMCBOOT - MMC Boot register + * - HW_SDHC_HOSTVER - Host Controller Version + * + * - hw_sdhc_t - Struct containing all module registers. + */ + +//! @name Module base addresses +//@{ +#ifndef REGS_SDHC_BASE +#define HW_SDHC_INSTANCE_COUNT (1U) //!< Number of instances of the SDHC module. +#define REGS_SDHC_BASE (0x400B1000U) //!< Base address for SDHC. +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_DSADDR - DMA System Address register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_DSADDR - DMA System Address register (RW) + * + * Reset value: 0x00000000U + * + * This register contains the physical system memory address used for DMA + * transfers. + */ +typedef union _hw_sdhc_dsaddr +{ + uint32_t U; + struct _hw_sdhc_dsaddr_bitfields + { + uint32_t RESERVED0 : 2; //!< [1:0] + uint32_t DSADDR : 30; //!< [31:2] DMA System Address + } B; +} hw_sdhc_dsaddr_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_DSADDR register + */ +//@{ +#define HW_SDHC_DSADDR_ADDR (REGS_SDHC_BASE + 0x0U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_DSADDR (*(__IO hw_sdhc_dsaddr_t *) HW_SDHC_DSADDR_ADDR) +#define HW_SDHC_DSADDR_RD() (HW_SDHC_DSADDR.U) +#define HW_SDHC_DSADDR_WR(v) (HW_SDHC_DSADDR.U = (v)) +#define HW_SDHC_DSADDR_SET(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() | (v))) +#define HW_SDHC_DSADDR_CLR(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() & ~(v))) +#define HW_SDHC_DSADDR_TOG(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_DSADDR bitfields + */ + +/*! + * @name Register SDHC_DSADDR, field DSADDR[31:2] (RW) + * + * Contains the 32-bit system memory address for a DMA transfer. Because the + * address must be word (4 bytes) align, the least 2 bits are reserved, always 0. + * When the SDHC stops a DMA transfer, this register points to the system address + * of the next contiguous data position. It can be accessed only when no + * transaction is executing, that is, after a transaction has stopped. Read operation + * during transfers may return an invalid value. The host driver shall initialize + * this register before starting a DMA transaction. After DMA has stopped, the + * system address of the next contiguous data position can be read from this register. + * This register is protected during a data transfer. When data lines are + * active, write to this register is ignored. The host driver shall wait, until + * PRSSTAT[DLA] is cleared, before writing to this register. The SDHC internal DMA does + * not support a virtual memory system. It supports only continuous physical + * memory access. And due to AHB burst limitations, if the burst must cross the 1 KB + * boundary, SDHC will automatically change SEQ burst type to NSEQ. Because this + * register supports dynamic address reflecting, when IRQSTAT[TC] bit is set, it + * automatically alters the value of internal address counter, so SW cannot + * change this register when IRQSTAT[TC] is set. + */ +//@{ +#define BP_SDHC_DSADDR_DSADDR (2U) //!< Bit position for SDHC_DSADDR_DSADDR. +#define BM_SDHC_DSADDR_DSADDR (0xFFFFFFFCU) //!< Bit mask for SDHC_DSADDR_DSADDR. +#define BS_SDHC_DSADDR_DSADDR (30U) //!< Bit field size in bits for SDHC_DSADDR_DSADDR. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_DSADDR_DSADDR field. +#define BR_SDHC_DSADDR_DSADDR (HW_SDHC_DSADDR.B.DSADDR) +#endif + +//! @brief Format value for bitfield SDHC_DSADDR_DSADDR. +#define BF_SDHC_DSADDR_DSADDR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_DSADDR_DSADDR), uint32_t) & BM_SDHC_DSADDR_DSADDR) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DSADDR field to a new value. +#define BW_SDHC_DSADDR_DSADDR(v) (HW_SDHC_DSADDR_WR((HW_SDHC_DSADDR_RD() & ~BM_SDHC_DSADDR_DSADDR) | BF_SDHC_DSADDR_DSADDR(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_BLKATTR - Block Attributes register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_BLKATTR - Block Attributes register (RW) + * + * Reset value: 0x00000000U + * + * This register is used to configure the number of data blocks and the number + * of bytes in each block. + */ +typedef union _hw_sdhc_blkattr +{ + uint32_t U; + struct _hw_sdhc_blkattr_bitfields + { + uint32_t BLKSIZE : 13; //!< [12:0] Transfer Block Size + uint32_t RESERVED0 : 3; //!< [15:13] + uint32_t BLKCNT : 16; //!< [31:16] Blocks Count For Current Transfer + } B; +} hw_sdhc_blkattr_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_BLKATTR register + */ +//@{ +#define HW_SDHC_BLKATTR_ADDR (REGS_SDHC_BASE + 0x4U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_BLKATTR (*(__IO hw_sdhc_blkattr_t *) HW_SDHC_BLKATTR_ADDR) +#define HW_SDHC_BLKATTR_RD() (HW_SDHC_BLKATTR.U) +#define HW_SDHC_BLKATTR_WR(v) (HW_SDHC_BLKATTR.U = (v)) +#define HW_SDHC_BLKATTR_SET(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() | (v))) +#define HW_SDHC_BLKATTR_CLR(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() & ~(v))) +#define HW_SDHC_BLKATTR_TOG(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_BLKATTR bitfields + */ + +/*! + * @name Register SDHC_BLKATTR, field BLKSIZE[12:0] (RW) + * + * Specifies the block size for block data transfers. Values ranging from 1 byte + * up to the maximum buffer size can be set. It can be accessed only when no + * transaction is executing, that is, after a transaction has stopped. Read + * operations during transfers may return an invalid value, and write operations will be + * ignored. + * + * Values: + * - 0 - No data transfer. + * - 1 - 1 Byte + * - 10 - 2 Bytes + * - 11 - 3 Bytes + * - 100 - 4 Bytes + * - 111111111 - 511 Bytes + * - 1000000000 - 512 Bytes + * - 100000000000 - 2048 Bytes + * - 1000000000000 - 4096 Bytes + */ +//@{ +#define BP_SDHC_BLKATTR_BLKSIZE (0U) //!< Bit position for SDHC_BLKATTR_BLKSIZE. +#define BM_SDHC_BLKATTR_BLKSIZE (0x00001FFFU) //!< Bit mask for SDHC_BLKATTR_BLKSIZE. +#define BS_SDHC_BLKATTR_BLKSIZE (13U) //!< Bit field size in bits for SDHC_BLKATTR_BLKSIZE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_BLKATTR_BLKSIZE field. +#define BR_SDHC_BLKATTR_BLKSIZE (HW_SDHC_BLKATTR.B.BLKSIZE) +#endif + +//! @brief Format value for bitfield SDHC_BLKATTR_BLKSIZE. +#define BF_SDHC_BLKATTR_BLKSIZE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_BLKATTR_BLKSIZE), uint32_t) & BM_SDHC_BLKATTR_BLKSIZE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BLKSIZE field to a new value. +#define BW_SDHC_BLKATTR_BLKSIZE(v) (HW_SDHC_BLKATTR_WR((HW_SDHC_BLKATTR_RD() & ~BM_SDHC_BLKATTR_BLKSIZE) | BF_SDHC_BLKATTR_BLKSIZE(v))) +#endif +//@} + +/*! + * @name Register SDHC_BLKATTR, field BLKCNT[31:16] (RW) + * + * This register is enabled when XFERTYP[BCEN] is set to 1 and is valid only for + * multiple block transfers. For single block transfer, this register will + * always read as 1. The host driver shall set this register to a value between 1 and + * the maximum block count. The SDHC decrements the block count after each block + * transfer and stops when the count reaches zero. Setting the block count to 0 + * results in no data blocks being transferred. This register must be accessed + * only when no transaction is executing, that is, after transactions are stopped. + * During data transfer, read operations on this register may return an invalid + * value and write operations are ignored. When saving transfer content as a result + * of a suspend command, the number of blocks yet to be transferred can be + * determined by reading this register. The reading of this register must be applied + * after transfer is paused by stop at block gap operation and before sending the + * command marked as suspend. This is because when suspend command is sent out, + * SDHC will regard the current transfer as aborted and change BLKCNT back to its + * original value instead of keeping the dynamical indicator of remained block + * count. When restoring transfer content prior to issuing a resume command, the + * host driver shall restore the previously saved block count. Although the BLKCNT + * field is 0 after reset, the read of reset value is 0x1. This is because when + * XFERTYP[MSBSEL] is 0, indicating a single block transfer, the read value of + * BLKCNT is always 1. + * + * Values: + * - 0 - Stop count. + * - 1 - 1 block + * - 10 - 2 blocks + * - 1111111111111111 - 65535 blocks + */ +//@{ +#define BP_SDHC_BLKATTR_BLKCNT (16U) //!< Bit position for SDHC_BLKATTR_BLKCNT. +#define BM_SDHC_BLKATTR_BLKCNT (0xFFFF0000U) //!< Bit mask for SDHC_BLKATTR_BLKCNT. +#define BS_SDHC_BLKATTR_BLKCNT (16U) //!< Bit field size in bits for SDHC_BLKATTR_BLKCNT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_BLKATTR_BLKCNT field. +#define BR_SDHC_BLKATTR_BLKCNT (HW_SDHC_BLKATTR.B.BLKCNT) +#endif + +//! @brief Format value for bitfield SDHC_BLKATTR_BLKCNT. +#define BF_SDHC_BLKATTR_BLKCNT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_BLKATTR_BLKCNT), uint32_t) & BM_SDHC_BLKATTR_BLKCNT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BLKCNT field to a new value. +#define BW_SDHC_BLKATTR_BLKCNT(v) (HW_SDHC_BLKATTR_WR((HW_SDHC_BLKATTR_RD() & ~BM_SDHC_BLKATTR_BLKCNT) | BF_SDHC_BLKATTR_BLKCNT(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_CMDARG - Command Argument register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_CMDARG - Command Argument register (RW) + * + * Reset value: 0x00000000U + * + * This register contains the SD/MMC command argument. + */ +typedef union _hw_sdhc_cmdarg +{ + uint32_t U; + struct _hw_sdhc_cmdarg_bitfields + { + uint32_t CMDARG : 32; //!< [31:0] Command Argument + } B; +} hw_sdhc_cmdarg_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_CMDARG register + */ +//@{ +#define HW_SDHC_CMDARG_ADDR (REGS_SDHC_BASE + 0x8U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_CMDARG (*(__IO hw_sdhc_cmdarg_t *) HW_SDHC_CMDARG_ADDR) +#define HW_SDHC_CMDARG_RD() (HW_SDHC_CMDARG.U) +#define HW_SDHC_CMDARG_WR(v) (HW_SDHC_CMDARG.U = (v)) +#define HW_SDHC_CMDARG_SET(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() | (v))) +#define HW_SDHC_CMDARG_CLR(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() & ~(v))) +#define HW_SDHC_CMDARG_TOG(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_CMDARG bitfields + */ + +/*! + * @name Register SDHC_CMDARG, field CMDARG[31:0] (RW) + * + * The SD/MMC command argument is specified as bits 39-8 of the command format + * in the SD or MMC specification. This register is write protected when + * PRSSTAT[CDIHB0] is set. + */ +//@{ +#define BP_SDHC_CMDARG_CMDARG (0U) //!< Bit position for SDHC_CMDARG_CMDARG. +#define BM_SDHC_CMDARG_CMDARG (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDARG_CMDARG. +#define BS_SDHC_CMDARG_CMDARG (32U) //!< Bit field size in bits for SDHC_CMDARG_CMDARG. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_CMDARG_CMDARG field. +#define BR_SDHC_CMDARG_CMDARG (HW_SDHC_CMDARG.U) +#endif + +//! @brief Format value for bitfield SDHC_CMDARG_CMDARG. +#define BF_SDHC_CMDARG_CMDARG(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_CMDARG_CMDARG), uint32_t) & BM_SDHC_CMDARG_CMDARG) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CMDARG field to a new value. +#define BW_SDHC_CMDARG_CMDARG(v) (HW_SDHC_CMDARG_WR(v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_XFERTYP - Transfer Type register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_XFERTYP - Transfer Type register (RW) + * + * Reset value: 0x00000000U + * + * This register is used to control the operation of data transfers. The host + * driver shall set this register before issuing a command followed by a data + * transfer, or before issuing a resume command. To prevent data loss, the SDHC + * prevents writing to the bits that are involved in the data transfer of this + * register, when data transfer is active. These bits are DPSEL, MBSEL, DTDSEL, AC12EN, + * BCEN, and DMAEN. The host driver shall check PRSSTAT[CDIHB] and PRSSTAT[CIHB] + * before writing to this register. When PRSSTAT[CDIHB] is set, any attempt to + * send a command with data by writing to this register is ignored; when + * PRSSTAT[CIHB] bit is set, any write to this register is ignored. On sending commands with + * data transfer involved, it is mandatory that the block size is nonzero. + * Besides, block count must also be nonzero, or indicated as single block transfer + * (bit 5 of this register is 0 when written), or block count is disabled (bit 1 of + * this register is 0 when written), otherwise SDHC will ignore the sending of + * this command and do nothing. For write command, with all above restrictions, it + * is also mandatory that the write protect switch is not active (WPSPL bit of + * Present State Register is 1), otherwise SDHC will also ignore the command. If + * the commands with data transfer does not receive the response in 64 clock + * cycles, that is, response time-out, SDHC will regard the external device does not + * accept the command and abort the data transfer. In this scenario, the driver + * must issue the command again to retry the transfer. It is also possible that, + * for some reason, the card responds to the command but SDHC does not receive the + * response, and if it is internal DMA (either simple DMA or ADMA) read + * operation, the external system memory is over-written by the internal DMA with data + * sent back from the card. The following table shows the summary of how register + * settings determine the type of data transfer. Transfer Type register setting for + * various transfer types Multi/Single block select Block count enable Block + * count Function 0 Don't care Don't care Single transfer 1 0 Don't care Infinite + * transfer 1 1 Positive number Multiple transfer 1 1 Zero No data transfer The + * following table shows the relationship between XFERTYP[CICEN] and XFERTYP[CCCEN], + * in regards to XFERTYP[RSPTYP] as well as the name of the response type. + * Relationship between parameters and the name of the response type Response type + * (RSPTYP) Index check enable (CICEN) CRC check enable (CCCEN) Name of response + * type 00 0 0 No Response 01 0 1 IR2 10 0 0 R3,R4 10 1 1 R1,R5,R6 11 1 1 R1b,R5b In + * the SDIO specification, response type notation for R5b is not defined. R5 + * includes R5b in the SDIO specification. But R5b is defined in this specification + * to specify that the SDHC will check the busy status after receiving a + * response. For example, usually CMD52 is used with R5, but the I/O abort command shall + * be used with R5b. The CRC field for R3 and R4 is expected to be all 1 bits. + * The CRC check shall be disabled for these response types. + */ +typedef union _hw_sdhc_xfertyp +{ + uint32_t U; + struct _hw_sdhc_xfertyp_bitfields + { + uint32_t DMAEN : 1; //!< [0] DMA Enable + uint32_t BCEN : 1; //!< [1] Block Count Enable + uint32_t AC12EN : 1; //!< [2] Auto CMD12 Enable + uint32_t RESERVED0 : 1; //!< [3] + uint32_t DTDSEL : 1; //!< [4] Data Transfer Direction Select + uint32_t MSBSEL : 1; //!< [5] Multi/Single Block Select + uint32_t RESERVED1 : 10; //!< [15:6] + uint32_t RSPTYP : 2; //!< [17:16] Response Type Select + uint32_t RESERVED2 : 1; //!< [18] + uint32_t CCCEN : 1; //!< [19] Command CRC Check Enable + uint32_t CICEN : 1; //!< [20] Command Index Check Enable + uint32_t DPSEL : 1; //!< [21] Data Present Select + uint32_t CMDTYP : 2; //!< [23:22] Command Type + uint32_t CMDINX : 6; //!< [29:24] Command Index + uint32_t RESERVED3 : 2; //!< [31:30] + } B; +} hw_sdhc_xfertyp_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_XFERTYP register + */ +//@{ +#define HW_SDHC_XFERTYP_ADDR (REGS_SDHC_BASE + 0xCU) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_XFERTYP (*(__IO hw_sdhc_xfertyp_t *) HW_SDHC_XFERTYP_ADDR) +#define HW_SDHC_XFERTYP_RD() (HW_SDHC_XFERTYP.U) +#define HW_SDHC_XFERTYP_WR(v) (HW_SDHC_XFERTYP.U = (v)) +#define HW_SDHC_XFERTYP_SET(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() | (v))) +#define HW_SDHC_XFERTYP_CLR(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() & ~(v))) +#define HW_SDHC_XFERTYP_TOG(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_XFERTYP bitfields + */ + +/*! + * @name Register SDHC_XFERTYP, field DMAEN[0] (RW) + * + * Enables DMA functionality. If this bit is set to 1, a DMA operation shall + * begin when the host driver sets the DPSEL bit of this register. Whether the + * simple DMA, or the advanced DMA, is active depends on PROCTL[DMAS]. + * + * Values: + * - 0 - Disable + * - 1 - Enable + */ +//@{ +#define BP_SDHC_XFERTYP_DMAEN (0U) //!< Bit position for SDHC_XFERTYP_DMAEN. +#define BM_SDHC_XFERTYP_DMAEN (0x00000001U) //!< Bit mask for SDHC_XFERTYP_DMAEN. +#define BS_SDHC_XFERTYP_DMAEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_DMAEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_DMAEN field. +#define BR_SDHC_XFERTYP_DMAEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DMAEN)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_DMAEN. +#define BF_SDHC_XFERTYP_DMAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DMAEN), uint32_t) & BM_SDHC_XFERTYP_DMAEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAEN field to a new value. +#define BW_SDHC_XFERTYP_DMAEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DMAEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field BCEN[1] (RW) + * + * Used to enable the Block Count register, which is only relevant for multiple + * block transfers. When this bit is 0, the internal counter for block is + * disabled, which is useful in executing an infinite transfer. + * + * Values: + * - 0 - Disable + * - 1 - Enable + */ +//@{ +#define BP_SDHC_XFERTYP_BCEN (1U) //!< Bit position for SDHC_XFERTYP_BCEN. +#define BM_SDHC_XFERTYP_BCEN (0x00000002U) //!< Bit mask for SDHC_XFERTYP_BCEN. +#define BS_SDHC_XFERTYP_BCEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_BCEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_BCEN field. +#define BR_SDHC_XFERTYP_BCEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_BCEN)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_BCEN. +#define BF_SDHC_XFERTYP_BCEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_BCEN), uint32_t) & BM_SDHC_XFERTYP_BCEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BCEN field to a new value. +#define BW_SDHC_XFERTYP_BCEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_BCEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field AC12EN[2] (RW) + * + * Multiple block transfers for memory require a CMD12 to stop the transaction. + * When this bit is set to 1, the SDHC will issue a CMD12 automatically when the + * last block transfer has completed. The host driver shall not set this bit to + * issue commands that do not require CMD12 to stop a multiple block data + * transfer. In particular, secure commands defined in File Security Specification (see + * reference list) do not require CMD12. In single block transfer, the SDHC will + * ignore this bit whether it is set or not. + * + * Values: + * - 0 - Disable + * - 1 - Enable + */ +//@{ +#define BP_SDHC_XFERTYP_AC12EN (2U) //!< Bit position for SDHC_XFERTYP_AC12EN. +#define BM_SDHC_XFERTYP_AC12EN (0x00000004U) //!< Bit mask for SDHC_XFERTYP_AC12EN. +#define BS_SDHC_XFERTYP_AC12EN (1U) //!< Bit field size in bits for SDHC_XFERTYP_AC12EN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_AC12EN field. +#define BR_SDHC_XFERTYP_AC12EN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_AC12EN)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_AC12EN. +#define BF_SDHC_XFERTYP_AC12EN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_AC12EN), uint32_t) & BM_SDHC_XFERTYP_AC12EN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12EN field to a new value. +#define BW_SDHC_XFERTYP_AC12EN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_AC12EN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field DTDSEL[4] (RW) + * + * Defines the direction of DAT line data transfers. The bit is set to 1 by the + * host driver to transfer data from the SD card to the SDHC and is set to 0 for + * all other commands. + * + * Values: + * - 0 - Write host to card. + * - 1 - Read card to host. + */ +//@{ +#define BP_SDHC_XFERTYP_DTDSEL (4U) //!< Bit position for SDHC_XFERTYP_DTDSEL. +#define BM_SDHC_XFERTYP_DTDSEL (0x00000010U) //!< Bit mask for SDHC_XFERTYP_DTDSEL. +#define BS_SDHC_XFERTYP_DTDSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_DTDSEL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_DTDSEL field. +#define BR_SDHC_XFERTYP_DTDSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DTDSEL)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_DTDSEL. +#define BF_SDHC_XFERTYP_DTDSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DTDSEL), uint32_t) & BM_SDHC_XFERTYP_DTDSEL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTDSEL field to a new value. +#define BW_SDHC_XFERTYP_DTDSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DTDSEL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field MSBSEL[5] (RW) + * + * Enables multiple block DAT line data transfers. For any other commands, this + * bit shall be set to 0. If this bit is 0, it is not necessary to set the block + * count register. + * + * Values: + * - 0 - Single block. + * - 1 - Multiple blocks. + */ +//@{ +#define BP_SDHC_XFERTYP_MSBSEL (5U) //!< Bit position for SDHC_XFERTYP_MSBSEL. +#define BM_SDHC_XFERTYP_MSBSEL (0x00000020U) //!< Bit mask for SDHC_XFERTYP_MSBSEL. +#define BS_SDHC_XFERTYP_MSBSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_MSBSEL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_MSBSEL field. +#define BR_SDHC_XFERTYP_MSBSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_MSBSEL)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_MSBSEL. +#define BF_SDHC_XFERTYP_MSBSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_MSBSEL), uint32_t) & BM_SDHC_XFERTYP_MSBSEL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the MSBSEL field to a new value. +#define BW_SDHC_XFERTYP_MSBSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_MSBSEL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field RSPTYP[17:16] (RW) + * + * Values: + * - 00 - No response. + * - 01 - Response length 136. + * - 10 - Response length 48. + * - 11 - Response length 48, check busy after response. + */ +//@{ +#define BP_SDHC_XFERTYP_RSPTYP (16U) //!< Bit position for SDHC_XFERTYP_RSPTYP. +#define BM_SDHC_XFERTYP_RSPTYP (0x00030000U) //!< Bit mask for SDHC_XFERTYP_RSPTYP. +#define BS_SDHC_XFERTYP_RSPTYP (2U) //!< Bit field size in bits for SDHC_XFERTYP_RSPTYP. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_RSPTYP field. +#define BR_SDHC_XFERTYP_RSPTYP (HW_SDHC_XFERTYP.B.RSPTYP) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_RSPTYP. +#define BF_SDHC_XFERTYP_RSPTYP(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_RSPTYP), uint32_t) & BM_SDHC_XFERTYP_RSPTYP) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RSPTYP field to a new value. +#define BW_SDHC_XFERTYP_RSPTYP(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_RSPTYP) | BF_SDHC_XFERTYP_RSPTYP(v))) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field CCCEN[19] (RW) + * + * If this bit is set to 1, the SDHC shall check the CRC field in the response. + * If an error is detected, it is reported as a Command CRC Error. If this bit is + * set to 0, the CRC field is not checked. The number of bits checked by the CRC + * field value changes according to the length of the response. + * + * Values: + * - 0 - Disable + * - 1 - Enable + */ +//@{ +#define BP_SDHC_XFERTYP_CCCEN (19U) //!< Bit position for SDHC_XFERTYP_CCCEN. +#define BM_SDHC_XFERTYP_CCCEN (0x00080000U) //!< Bit mask for SDHC_XFERTYP_CCCEN. +#define BS_SDHC_XFERTYP_CCCEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_CCCEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_CCCEN field. +#define BR_SDHC_XFERTYP_CCCEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CCCEN)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_CCCEN. +#define BF_SDHC_XFERTYP_CCCEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CCCEN), uint32_t) & BM_SDHC_XFERTYP_CCCEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCCEN field to a new value. +#define BW_SDHC_XFERTYP_CCCEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CCCEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field CICEN[20] (RW) + * + * If this bit is set to 1, the SDHC will check the index field in the response + * to see if it has the same value as the command index. If it is not, it is + * reported as a command index error. If this bit is set to 0, the index field is not + * checked. + * + * Values: + * - 0 - Disable + * - 1 - Enable + */ +//@{ +#define BP_SDHC_XFERTYP_CICEN (20U) //!< Bit position for SDHC_XFERTYP_CICEN. +#define BM_SDHC_XFERTYP_CICEN (0x00100000U) //!< Bit mask for SDHC_XFERTYP_CICEN. +#define BS_SDHC_XFERTYP_CICEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_CICEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_CICEN field. +#define BR_SDHC_XFERTYP_CICEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CICEN)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_CICEN. +#define BF_SDHC_XFERTYP_CICEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CICEN), uint32_t) & BM_SDHC_XFERTYP_CICEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CICEN field to a new value. +#define BW_SDHC_XFERTYP_CICEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CICEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field DPSEL[21] (RW) + * + * This bit is set to 1 to indicate that data is present and shall be + * transferred using the DAT line. It is set to 0 for the following: Commands using only + * the CMD line, for example: CMD52. Commands with no data transfer, but using the + * busy signal on DAT[0] line, R1b or R5b, for example: CMD38. In resume command, + * this bit shall be set, and other bits in this register shall be set the same + * as when the transfer was initially launched. When the Write Protect switch is + * on, that is, the WPSPL bit is active as 0, any command with a write operation + * will be ignored. That is to say, when this bit is set, while the DTDSEL bit is + * 0, writes to the register Transfer Type are ignored. + * + * Values: + * - 0 - No data present. + * - 1 - Data present. + */ +//@{ +#define BP_SDHC_XFERTYP_DPSEL (21U) //!< Bit position for SDHC_XFERTYP_DPSEL. +#define BM_SDHC_XFERTYP_DPSEL (0x00200000U) //!< Bit mask for SDHC_XFERTYP_DPSEL. +#define BS_SDHC_XFERTYP_DPSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_DPSEL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_DPSEL field. +#define BR_SDHC_XFERTYP_DPSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DPSEL)) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_DPSEL. +#define BF_SDHC_XFERTYP_DPSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DPSEL), uint32_t) & BM_SDHC_XFERTYP_DPSEL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DPSEL field to a new value. +#define BW_SDHC_XFERTYP_DPSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DPSEL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field CMDTYP[23:22] (RW) + * + * There are three types of special commands: suspend, resume, and abort. These + * bits shall be set to 00b for all other commands. Suspend command: If the + * suspend command succeeds, the SDHC shall assume that the card bus has been released + * and that it is possible to issue the next command which uses the DAT line. + * Because the SDHC does not monitor the content of command response, it does not + * know if the suspend command succeeded or not. It is the host driver's + * responsibility to check the status of the suspend command and send another command + * marked as suspend to inform the SDHC that a suspend command was successfully + * issued. After the end bit of command is sent, the SDHC deasserts read wait for read + * transactions and stops checking busy for write transactions. In 4-bit mode, + * the interrupt cycle starts. If the suspend command fails, the SDHC will + * maintain its current state, and the host driver shall restart the transfer by setting + * PROCTL[CREQ]. Resume command: The host driver restarts the data transfer by + * restoring the registers saved before sending the suspend command and then sends + * the resume command. The SDHC will check for a pending busy state before + * starting write transfers. Abort command: If this command is set when executing a + * read transfer, the SDHC will stop reads to the buffer. If this command is set + * when executing a write transfer, the SDHC will stop driving the DAT line. After + * issuing the abort command, the host driver must issue a software reset (abort + * transaction). + * + * Values: + * - 00 - Normal other commands. + * - 01 - Suspend CMD52 for writing bus suspend in CCCR. + * - 10 - Resume CMD52 for writing function select in CCCR. + * - 11 - Abort CMD12, CMD52 for writing I/O abort in CCCR. + */ +//@{ +#define BP_SDHC_XFERTYP_CMDTYP (22U) //!< Bit position for SDHC_XFERTYP_CMDTYP. +#define BM_SDHC_XFERTYP_CMDTYP (0x00C00000U) //!< Bit mask for SDHC_XFERTYP_CMDTYP. +#define BS_SDHC_XFERTYP_CMDTYP (2U) //!< Bit field size in bits for SDHC_XFERTYP_CMDTYP. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_CMDTYP field. +#define BR_SDHC_XFERTYP_CMDTYP (HW_SDHC_XFERTYP.B.CMDTYP) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_CMDTYP. +#define BF_SDHC_XFERTYP_CMDTYP(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CMDTYP), uint32_t) & BM_SDHC_XFERTYP_CMDTYP) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CMDTYP field to a new value. +#define BW_SDHC_XFERTYP_CMDTYP(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_CMDTYP) | BF_SDHC_XFERTYP_CMDTYP(v))) +#endif +//@} + +/*! + * @name Register SDHC_XFERTYP, field CMDINX[29:24] (RW) + * + * These bits shall be set to the command number that is specified in bits 45-40 + * of the command-format in the SD Memory Card Physical Layer Specification and + * SDIO Card Specification. + */ +//@{ +#define BP_SDHC_XFERTYP_CMDINX (24U) //!< Bit position for SDHC_XFERTYP_CMDINX. +#define BM_SDHC_XFERTYP_CMDINX (0x3F000000U) //!< Bit mask for SDHC_XFERTYP_CMDINX. +#define BS_SDHC_XFERTYP_CMDINX (6U) //!< Bit field size in bits for SDHC_XFERTYP_CMDINX. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_XFERTYP_CMDINX field. +#define BR_SDHC_XFERTYP_CMDINX (HW_SDHC_XFERTYP.B.CMDINX) +#endif + +//! @brief Format value for bitfield SDHC_XFERTYP_CMDINX. +#define BF_SDHC_XFERTYP_CMDINX(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CMDINX), uint32_t) & BM_SDHC_XFERTYP_CMDINX) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CMDINX field to a new value. +#define BW_SDHC_XFERTYP_CMDINX(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_CMDINX) | BF_SDHC_XFERTYP_CMDINX(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_CMDRSP0 - Command Response 0 +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_CMDRSP0 - Command Response 0 (RO) + * + * Reset value: 0x00000000U + * + * This register is used to store part 0 of the response bits from the card. + */ +typedef union _hw_sdhc_cmdrsp0 +{ + uint32_t U; + struct _hw_sdhc_cmdrsp0_bitfields + { + uint32_t CMDRSP0 : 32; //!< [31:0] Command Response 0 + } B; +} hw_sdhc_cmdrsp0_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_CMDRSP0 register + */ +//@{ +#define HW_SDHC_CMDRSP0_ADDR (REGS_SDHC_BASE + 0x10U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_CMDRSP0 (*(__I hw_sdhc_cmdrsp0_t *) HW_SDHC_CMDRSP0_ADDR) +#define HW_SDHC_CMDRSP0_RD() (HW_SDHC_CMDRSP0.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_CMDRSP0 bitfields + */ + +/*! + * @name Register SDHC_CMDRSP0, field CMDRSP0[31:0] (RO) + */ +//@{ +#define BP_SDHC_CMDRSP0_CMDRSP0 (0U) //!< Bit position for SDHC_CMDRSP0_CMDRSP0. +#define BM_SDHC_CMDRSP0_CMDRSP0 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP0_CMDRSP0. +#define BS_SDHC_CMDRSP0_CMDRSP0 (32U) //!< Bit field size in bits for SDHC_CMDRSP0_CMDRSP0. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_CMDRSP0_CMDRSP0 field. +#define BR_SDHC_CMDRSP0_CMDRSP0 (HW_SDHC_CMDRSP0.U) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_CMDRSP1 - Command Response 1 +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_CMDRSP1 - Command Response 1 (RO) + * + * Reset value: 0x00000000U + * + * This register is used to store part 1 of the response bits from the card. + */ +typedef union _hw_sdhc_cmdrsp1 +{ + uint32_t U; + struct _hw_sdhc_cmdrsp1_bitfields + { + uint32_t CMDRSP1 : 32; //!< [31:0] Command Response 1 + } B; +} hw_sdhc_cmdrsp1_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_CMDRSP1 register + */ +//@{ +#define HW_SDHC_CMDRSP1_ADDR (REGS_SDHC_BASE + 0x14U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_CMDRSP1 (*(__I hw_sdhc_cmdrsp1_t *) HW_SDHC_CMDRSP1_ADDR) +#define HW_SDHC_CMDRSP1_RD() (HW_SDHC_CMDRSP1.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_CMDRSP1 bitfields + */ + +/*! + * @name Register SDHC_CMDRSP1, field CMDRSP1[31:0] (RO) + */ +//@{ +#define BP_SDHC_CMDRSP1_CMDRSP1 (0U) //!< Bit position for SDHC_CMDRSP1_CMDRSP1. +#define BM_SDHC_CMDRSP1_CMDRSP1 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP1_CMDRSP1. +#define BS_SDHC_CMDRSP1_CMDRSP1 (32U) //!< Bit field size in bits for SDHC_CMDRSP1_CMDRSP1. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_CMDRSP1_CMDRSP1 field. +#define BR_SDHC_CMDRSP1_CMDRSP1 (HW_SDHC_CMDRSP1.U) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_CMDRSP2 - Command Response 2 +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_CMDRSP2 - Command Response 2 (RO) + * + * Reset value: 0x00000000U + * + * This register is used to store part 2 of the response bits from the card. + */ +typedef union _hw_sdhc_cmdrsp2 +{ + uint32_t U; + struct _hw_sdhc_cmdrsp2_bitfields + { + uint32_t CMDRSP2 : 32; //!< [31:0] Command Response 2 + } B; +} hw_sdhc_cmdrsp2_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_CMDRSP2 register + */ +//@{ +#define HW_SDHC_CMDRSP2_ADDR (REGS_SDHC_BASE + 0x18U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_CMDRSP2 (*(__I hw_sdhc_cmdrsp2_t *) HW_SDHC_CMDRSP2_ADDR) +#define HW_SDHC_CMDRSP2_RD() (HW_SDHC_CMDRSP2.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_CMDRSP2 bitfields + */ + +/*! + * @name Register SDHC_CMDRSP2, field CMDRSP2[31:0] (RO) + */ +//@{ +#define BP_SDHC_CMDRSP2_CMDRSP2 (0U) //!< Bit position for SDHC_CMDRSP2_CMDRSP2. +#define BM_SDHC_CMDRSP2_CMDRSP2 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP2_CMDRSP2. +#define BS_SDHC_CMDRSP2_CMDRSP2 (32U) //!< Bit field size in bits for SDHC_CMDRSP2_CMDRSP2. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_CMDRSP2_CMDRSP2 field. +#define BR_SDHC_CMDRSP2_CMDRSP2 (HW_SDHC_CMDRSP2.U) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_CMDRSP3 - Command Response 3 +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_CMDRSP3 - Command Response 3 (RO) + * + * Reset value: 0x00000000U + * + * This register is used to store part 3 of the response bits from the card. The + * following table describes the mapping of command responses from the SD bus to + * command response registers for each response type. In the table, R[ ] refers + * to a bit range within the response data as transmitted on the SD bus. Response + * bit definition for each response type Response type Meaning of response + * Response field Response register R1,R1b (normal response) Card status R[39:8] + * CMDRSP0 R1b (Auto CMD12 response) Card status for auto CMD12 R[39:8] CMDRSP3 R2 + * (CID, CSD register) CID/CSD register [127:8] R[127:8] {CMDRSP3[23:0], CMDRSP2, + * CMDRSP1, CMDRSP0} R3 (OCR register) OCR register for memory R[39:8] CMDRSP0 R4 + * (OCR register) OCR register for I/O etc. R[39:8] CMDRSP0 R5, R5b SDIO response + * R[39:8] CMDRSP0 R6 (Publish RCA) New published RCA[31:16] and card + * status[15:0] R[39:9] CMDRSP0 This table shows that most responses with a length of 48 + * (R[47:0]) have 32-bit of the response data (R[39:8]) stored in the CMDRSP0 + * register. Responses of type R1b (auto CMD12 responses) have response data bits + * (R[39:8]) stored in the CMDRSP3 register. Responses with length 136 (R[135:0]) have + * 120-bit of the response data (R[127:8]) stored in the CMDRSP0, 1, 2, and 3 + * registers. To be able to read the response status efficiently, the SDHC stores + * only a part of the response data in the command response registers. This + * enables the host driver to efficiently read 32-bit of response data in one read + * cycle on a 32-bit bus system. Parts of the response, the index field and the CRC, + * are checked by the SDHC, as specified by XFERTYP[CICEN] and XFERTYP[CCCEN], + * and generate an error interrupt if any error is detected. The bit range for the + * CRC check depends on the response length. If the response length is 48, the + * SDHC will check R[47:1], and if the response length is 136 the SDHC will check + * R[119:1]. Because the SDHC may have a multiple block data transfer executing + * concurrently with a CMD_wo_DAT command, the SDHC stores the auto CMD12 response + * in the CMDRSP3 register. The CMD_wo_DAT response is stored in CMDRSP0. This + * allows the SDHC to avoid overwriting the Auto CMD12 response with the CMD_wo_DAT + * and vice versa. When the SDHC modifies part of the command response + * registers, as shown in the table above, it preserves the unmodified bits. + */ +typedef union _hw_sdhc_cmdrsp3 +{ + uint32_t U; + struct _hw_sdhc_cmdrsp3_bitfields + { + uint32_t CMDRSP3 : 32; //!< [31:0] Command Response 3 + } B; +} hw_sdhc_cmdrsp3_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_CMDRSP3 register + */ +//@{ +#define HW_SDHC_CMDRSP3_ADDR (REGS_SDHC_BASE + 0x1CU) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_CMDRSP3 (*(__I hw_sdhc_cmdrsp3_t *) HW_SDHC_CMDRSP3_ADDR) +#define HW_SDHC_CMDRSP3_RD() (HW_SDHC_CMDRSP3.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_CMDRSP3 bitfields + */ + +/*! + * @name Register SDHC_CMDRSP3, field CMDRSP3[31:0] (RO) + */ +//@{ +#define BP_SDHC_CMDRSP3_CMDRSP3 (0U) //!< Bit position for SDHC_CMDRSP3_CMDRSP3. +#define BM_SDHC_CMDRSP3_CMDRSP3 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP3_CMDRSP3. +#define BS_SDHC_CMDRSP3_CMDRSP3 (32U) //!< Bit field size in bits for SDHC_CMDRSP3_CMDRSP3. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_CMDRSP3_CMDRSP3 field. +#define BR_SDHC_CMDRSP3_CMDRSP3 (HW_SDHC_CMDRSP3.U) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_DATPORT - Buffer Data Port register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_DATPORT - Buffer Data Port register (RW) + * + * Reset value: 0x00000000U + * + * This is a 32-bit data port register used to access the internal buffer and it + * cannot be updated in Idle mode. + */ +typedef union _hw_sdhc_datport +{ + uint32_t U; + struct _hw_sdhc_datport_bitfields + { + uint32_t DATCONT : 32; //!< [31:0] Data Content + } B; +} hw_sdhc_datport_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_DATPORT register + */ +//@{ +#define HW_SDHC_DATPORT_ADDR (REGS_SDHC_BASE + 0x20U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_DATPORT (*(__IO hw_sdhc_datport_t *) HW_SDHC_DATPORT_ADDR) +#define HW_SDHC_DATPORT_RD() (HW_SDHC_DATPORT.U) +#define HW_SDHC_DATPORT_WR(v) (HW_SDHC_DATPORT.U = (v)) +#define HW_SDHC_DATPORT_SET(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() | (v))) +#define HW_SDHC_DATPORT_CLR(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() & ~(v))) +#define HW_SDHC_DATPORT_TOG(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_DATPORT bitfields + */ + +/*! + * @name Register SDHC_DATPORT, field DATCONT[31:0] (RW) + * + * The Buffer Data Port register is for 32-bit data access by the CPU or the + * external DMA. When the internal DMA is enabled, any write to this register is + * ignored, and any read from this register will always yield 0s. + */ +//@{ +#define BP_SDHC_DATPORT_DATCONT (0U) //!< Bit position for SDHC_DATPORT_DATCONT. +#define BM_SDHC_DATPORT_DATCONT (0xFFFFFFFFU) //!< Bit mask for SDHC_DATPORT_DATCONT. +#define BS_SDHC_DATPORT_DATCONT (32U) //!< Bit field size in bits for SDHC_DATPORT_DATCONT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_DATPORT_DATCONT field. +#define BR_SDHC_DATPORT_DATCONT (HW_SDHC_DATPORT.U) +#endif + +//! @brief Format value for bitfield SDHC_DATPORT_DATCONT. +#define BF_SDHC_DATPORT_DATCONT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_DATPORT_DATCONT), uint32_t) & BM_SDHC_DATPORT_DATCONT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DATCONT field to a new value. +#define BW_SDHC_DATPORT_DATCONT(v) (HW_SDHC_DATPORT_WR(v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_PRSSTAT - Present State register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_PRSSTAT - Present State register (RO) + * + * Reset value: 0x00000000U + * + * The host driver can get status of the SDHC from this 32-bit read-only + * register. The host driver can issue CMD0, CMD12, CMD13 (for memory) and CMD52 (for + * SDIO) when the DAT lines are busy during a data transfer. These commands can be + * issued when Command Inhibit (CIHB) is set to zero. Other commands shall be + * issued when Command Inhibit (CDIHB) is set to zero. Possible changes to the SD + * Physical Specification may add other commands to this list in the future. + */ +typedef union _hw_sdhc_prsstat +{ + uint32_t U; + struct _hw_sdhc_prsstat_bitfields + { + uint32_t CIHB : 1; //!< [0] Command Inhibit (CMD) + uint32_t CDIHB : 1; //!< [1] Command Inhibit (DAT) + uint32_t DLA : 1; //!< [2] Data Line Active + uint32_t SDSTB : 1; //!< [3] SD Clock Stable + uint32_t IPGOFF : 1; //!< [4] Bus Clock Gated Off Internally + uint32_t HCKOFF : 1; //!< [5] System Clock Gated Off Internally + uint32_t PEROFF : 1; //!< [6] SDHC clock Gated Off Internally + uint32_t SDOFF : 1; //!< [7] SD Clock Gated Off Internally + uint32_t WTA : 1; //!< [8] Write Transfer Active + uint32_t RTA : 1; //!< [9] Read Transfer Active + uint32_t BWEN : 1; //!< [10] Buffer Write Enable + uint32_t BREN : 1; //!< [11] Buffer Read Enable + uint32_t RESERVED0 : 4; //!< [15:12] + uint32_t CINS : 1; //!< [16] Card Inserted + uint32_t RESERVED1 : 6; //!< [22:17] + uint32_t CLSL : 1; //!< [23] CMD Line Signal Level + uint32_t DLSL : 8; //!< [31:24] DAT Line Signal Level + } B; +} hw_sdhc_prsstat_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_PRSSTAT register + */ +//@{ +#define HW_SDHC_PRSSTAT_ADDR (REGS_SDHC_BASE + 0x24U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_PRSSTAT (*(__I hw_sdhc_prsstat_t *) HW_SDHC_PRSSTAT_ADDR) +#define HW_SDHC_PRSSTAT_RD() (HW_SDHC_PRSSTAT.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_PRSSTAT bitfields + */ + +/*! + * @name Register SDHC_PRSSTAT, field CIHB[0] (RO) + * + * If this status bit is 0, it indicates that the CMD line is not in use and the + * SDHC can issue a SD/MMC Command using the CMD line. This bit is set also + * immediately after the Transfer Type register is written. This bit is cleared when + * the command response is received. Even if the CDIHB bit is set to 1, Commands + * using only the CMD line can be issued if this bit is 0. Changing from 1 to 0 + * generates a command complete interrupt in the interrupt status register. If the + * SDHC cannot issue the command because of a command conflict error (see + * command CRC error) or because of a command not issued by auto CMD12 error, this bit + * will remain 1 and the command complete is not set. The status of issuing an + * auto CMD12 does not show on this bit. + * + * Values: + * - 0 - Can issue command using only CMD line. + * - 1 - Cannot issue command. + */ +//@{ +#define BP_SDHC_PRSSTAT_CIHB (0U) //!< Bit position for SDHC_PRSSTAT_CIHB. +#define BM_SDHC_PRSSTAT_CIHB (0x00000001U) //!< Bit mask for SDHC_PRSSTAT_CIHB. +#define BS_SDHC_PRSSTAT_CIHB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CIHB. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_CIHB field. +#define BR_SDHC_PRSSTAT_CIHB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CIHB)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field CDIHB[1] (RO) + * + * This status bit is generated if either the DLA or the RTA is set to 1. If + * this bit is 0, it indicates that the SDHC can issue the next SD/MMC Command. + * Commands with a busy signal belong to CDIHB, for example, R1b, R5b type. Except in + * the case when the command busy is finished, changing from 1 to 0 generates a + * transfer complete interrupt in the Interrupt Status register. The SD host + * driver can save registers for a suspend transaction after this bit has changed + * from 1 to 0. + * + * Values: + * - 0 - Can issue command which uses the DAT line. + * - 1 - Cannot issue command which uses the DAT line. + */ +//@{ +#define BP_SDHC_PRSSTAT_CDIHB (1U) //!< Bit position for SDHC_PRSSTAT_CDIHB. +#define BM_SDHC_PRSSTAT_CDIHB (0x00000002U) //!< Bit mask for SDHC_PRSSTAT_CDIHB. +#define BS_SDHC_PRSSTAT_CDIHB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CDIHB. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_CDIHB field. +#define BR_SDHC_PRSSTAT_CDIHB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CDIHB)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field DLA[2] (RO) + * + * Indicates whether one of the DAT lines on the SD bus is in use. In the case + * of read transactions: This status indicates whether a read transfer is + * executing on the SD bus. Changes in this value from 1 to 0, between data blocks, + * generates a block gap event interrupt in the Interrupt Status register. This bit + * will be set in either of the following cases: After the end bit of the read + * command. When writing a 1 to PROCTL[CREQ] to restart a read transfer. This bit + * will be cleared in either of the following cases: When the end bit of the last + * data block is sent from the SD bus to the SDHC. When the read wait state is + * stopped by a suspend command and the DAT2 line is released. The SDHC will wait at + * the next block gap by driving read wait at the start of the interrupt cycle. + * If the read wait signal is already driven (data buffer cannot receive data), + * the SDHC can wait for a current block gap by continuing to drive the read wait + * signal. It is necessary to support read wait to use the suspend / resume + * function. This bit will remain 1 during read wait. In the case of write + * transactions: This status indicates that a write transfer is executing on the SD bus. + * Changes in this value from 1 to 0 generate a transfer complete interrupt in the + * interrupt status register. This bit will be set in either of the following + * cases: After the end bit of the write command. When writing to 1 to PROCTL[CREQ] to + * continue a write transfer. This bit will be cleared in either of the + * following cases: When the SD card releases write busy of the last data block, the SDHC + * will also detect if the output is not busy. If the SD card does not drive the + * busy signal after the CRC status is received, the SDHC shall assume the card + * drive "Not busy". When the SD card releases write busy, prior to waiting for + * write transfer, and as a result of a stop at block gap request. In the case of + * command with busy pending: This status indicates that a busy state follows the + * command and the data line is in use. This bit will be cleared when the DAT0 + * line is released. + * + * Values: + * - 0 - DAT line inactive. + * - 1 - DAT line active. + */ +//@{ +#define BP_SDHC_PRSSTAT_DLA (2U) //!< Bit position for SDHC_PRSSTAT_DLA. +#define BM_SDHC_PRSSTAT_DLA (0x00000004U) //!< Bit mask for SDHC_PRSSTAT_DLA. +#define BS_SDHC_PRSSTAT_DLA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_DLA. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_DLA field. +#define BR_SDHC_PRSSTAT_DLA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_DLA)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field SDSTB[3] (RO) + * + * Indicates that the internal card clock is stable. This bit is for the host + * driver to poll clock status when changing the clock frequency. It is recommended + * to clear SYSCTL[SDCLKEN] to remove glitch on the card clock when the + * frequency is changing. + * + * Values: + * - 0 - Clock is changing frequency and not stable. + * - 1 - Clock is stable. + */ +//@{ +#define BP_SDHC_PRSSTAT_SDSTB (3U) //!< Bit position for SDHC_PRSSTAT_SDSTB. +#define BM_SDHC_PRSSTAT_SDSTB (0x00000008U) //!< Bit mask for SDHC_PRSSTAT_SDSTB. +#define BS_SDHC_PRSSTAT_SDSTB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_SDSTB. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_SDSTB field. +#define BR_SDHC_PRSSTAT_SDSTB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_SDSTB)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field IPGOFF[4] (RO) + * + * Indicates that the bus clock is internally gated off. This bit is for the + * host driver to debug. + * + * Values: + * - 0 - Bus clock is active. + * - 1 - Bus clock is gated off. + */ +//@{ +#define BP_SDHC_PRSSTAT_IPGOFF (4U) //!< Bit position for SDHC_PRSSTAT_IPGOFF. +#define BM_SDHC_PRSSTAT_IPGOFF (0x00000010U) //!< Bit mask for SDHC_PRSSTAT_IPGOFF. +#define BS_SDHC_PRSSTAT_IPGOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_IPGOFF. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_IPGOFF field. +#define BR_SDHC_PRSSTAT_IPGOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_IPGOFF)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field HCKOFF[5] (RO) + * + * Indicates that the system clock is internally gated off. This bit is for the + * host driver to debug during a data transfer. + * + * Values: + * - 0 - System clock is active. + * - 1 - System clock is gated off. + */ +//@{ +#define BP_SDHC_PRSSTAT_HCKOFF (5U) //!< Bit position for SDHC_PRSSTAT_HCKOFF. +#define BM_SDHC_PRSSTAT_HCKOFF (0x00000020U) //!< Bit mask for SDHC_PRSSTAT_HCKOFF. +#define BS_SDHC_PRSSTAT_HCKOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_HCKOFF. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_HCKOFF field. +#define BR_SDHC_PRSSTAT_HCKOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_HCKOFF)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field PEROFF[6] (RO) + * + * Indicates that the is internally gated off. This bit is for the host driver + * to debug transaction on the SD bus. When INITA bit is set, SDHC sending 80 + * clock cycles to the card, SDCLKEN must be 1 to enable the output card clock, + * otherwise the will never be gate off, so and will be always active. SDHC clock SDHC + * clock SDHC clock bus clock + * + * Values: + * - 0 - SDHC clock is active. + * - 1 - SDHC clock is gated off. + */ +//@{ +#define BP_SDHC_PRSSTAT_PEROFF (6U) //!< Bit position for SDHC_PRSSTAT_PEROFF. +#define BM_SDHC_PRSSTAT_PEROFF (0x00000040U) //!< Bit mask for SDHC_PRSSTAT_PEROFF. +#define BS_SDHC_PRSSTAT_PEROFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_PEROFF. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_PEROFF field. +#define BR_SDHC_PRSSTAT_PEROFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_PEROFF)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field SDOFF[7] (RO) + * + * Indicates that the SD clock is internally gated off, because of buffer + * over/under-run or read pause without read wait assertion, or the driver has cleared + * SYSCTL[SDCLKEN] to stop the SD clock. This bit is for the host driver to debug + * data transaction on the SD bus. + * + * Values: + * - 0 - SD clock is active. + * - 1 - SD clock is gated off. + */ +//@{ +#define BP_SDHC_PRSSTAT_SDOFF (7U) //!< Bit position for SDHC_PRSSTAT_SDOFF. +#define BM_SDHC_PRSSTAT_SDOFF (0x00000080U) //!< Bit mask for SDHC_PRSSTAT_SDOFF. +#define BS_SDHC_PRSSTAT_SDOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_SDOFF. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_SDOFF field. +#define BR_SDHC_PRSSTAT_SDOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_SDOFF)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field WTA[8] (RO) + * + * Indicates that a write transfer is active. If this bit is 0, it means no + * valid write data exists in the SDHC. This bit is set in either of the following + * cases: After the end bit of the write command. When writing 1 to PROCTL[CREQ] to + * restart a write transfer. This bit is cleared in either of the following + * cases: After getting the CRC status of the last data block as specified by the + * transfer count (single and multiple). After getting the CRC status of any block + * where data transmission is about to be stopped by a stop at block gap request. + * During a write transaction, a block gap event interrupt is generated when this + * bit is changed to 0, as result of the stop at block gap request being set. + * This status is useful for the host driver in determining when to issue commands + * during write busy state. + * + * Values: + * - 0 - No valid data. + * - 1 - Transferring data. + */ +//@{ +#define BP_SDHC_PRSSTAT_WTA (8U) //!< Bit position for SDHC_PRSSTAT_WTA. +#define BM_SDHC_PRSSTAT_WTA (0x00000100U) //!< Bit mask for SDHC_PRSSTAT_WTA. +#define BS_SDHC_PRSSTAT_WTA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_WTA. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_WTA field. +#define BR_SDHC_PRSSTAT_WTA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_WTA)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field RTA[9] (RO) + * + * Used for detecting completion of a read transfer. This bit is set for either + * of the following conditions: After the end bit of the read command. When + * writing a 1 to PROCTL[CREQ] to restart a read transfer. A transfer complete + * interrupt is generated when this bit changes to 0. This bit is cleared for either of + * the following conditions: When the last data block as specified by block + * length is transferred to the system, that is, all data are read away from SDHC + * internal buffer. When all valid data blocks have been transferred from SDHC + * internal buffer to the system and no current block transfers are being sent as a + * result of the stop at block gap request being set to 1. + * + * Values: + * - 0 - No valid data. + * - 1 - Transferring data. + */ +//@{ +#define BP_SDHC_PRSSTAT_RTA (9U) //!< Bit position for SDHC_PRSSTAT_RTA. +#define BM_SDHC_PRSSTAT_RTA (0x00000200U) //!< Bit mask for SDHC_PRSSTAT_RTA. +#define BS_SDHC_PRSSTAT_RTA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_RTA. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_RTA field. +#define BR_SDHC_PRSSTAT_RTA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_RTA)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field BWEN[10] (RO) + * + * Used for non-DMA write transfers. The SDHC can implement multiple buffers to + * transfer data efficiently. This read-only flag indicates whether space is + * available for write data. If this bit is 1, valid data greater than the watermark + * level can be written to the buffer. This read-only flag indicates whether + * space is available for write data. + * + * Values: + * - 0 - Write disable, the buffer can hold valid data less than the write + * watermark level. + * - 1 - Write enable, the buffer can hold valid data greater than the write + * watermark level. + */ +//@{ +#define BP_SDHC_PRSSTAT_BWEN (10U) //!< Bit position for SDHC_PRSSTAT_BWEN. +#define BM_SDHC_PRSSTAT_BWEN (0x00000400U) //!< Bit mask for SDHC_PRSSTAT_BWEN. +#define BS_SDHC_PRSSTAT_BWEN (1U) //!< Bit field size in bits for SDHC_PRSSTAT_BWEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_BWEN field. +#define BR_SDHC_PRSSTAT_BWEN (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_BWEN)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field BREN[11] (RO) + * + * Used for non-DMA read transfers. The SDHC may implement multiple buffers to + * transfer data efficiently. This read-only flag indicates that valid data exists + * in the host side buffer. If this bit is high, valid data greater than the + * watermark level exist in the buffer. This read-only flag indicates that valid + * data exists in the host side buffer. + * + * Values: + * - 0 - Read disable, valid data less than the watermark level exist in the + * buffer. + * - 1 - Read enable, valid data greater than the watermark level exist in the + * buffer. + */ +//@{ +#define BP_SDHC_PRSSTAT_BREN (11U) //!< Bit position for SDHC_PRSSTAT_BREN. +#define BM_SDHC_PRSSTAT_BREN (0x00000800U) //!< Bit mask for SDHC_PRSSTAT_BREN. +#define BS_SDHC_PRSSTAT_BREN (1U) //!< Bit field size in bits for SDHC_PRSSTAT_BREN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_BREN field. +#define BR_SDHC_PRSSTAT_BREN (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_BREN)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field CINS[16] (RO) + * + * Indicates whether a card has been inserted. The SDHC debounces this signal so + * that the host driver will not need to wait for it to stabilize. Changing from + * a 0 to 1 generates a card insertion interrupt in the Interrupt Status + * register. Changing from a 1 to 0 generates a card removal interrupt in the Interrupt + * Status register. A write to the force event register does not effect this bit. + * SYSCTL[RSTA] does not effect this bit. A software reset does not effect this + * bit. + * + * Values: + * - 0 - Power on reset or no card. + * - 1 - Card inserted. + */ +//@{ +#define BP_SDHC_PRSSTAT_CINS (16U) //!< Bit position for SDHC_PRSSTAT_CINS. +#define BM_SDHC_PRSSTAT_CINS (0x00010000U) //!< Bit mask for SDHC_PRSSTAT_CINS. +#define BS_SDHC_PRSSTAT_CINS (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CINS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_CINS field. +#define BR_SDHC_PRSSTAT_CINS (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CINS)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field CLSL[23] (RO) + * + * Used to check the CMD line level to recover from errors, and for debugging. + * The reset value is effected by the external pullup/pulldown resistor, by + * default, the read value of this bit after reset is 1b, when the command line is + * pulled up. + */ +//@{ +#define BP_SDHC_PRSSTAT_CLSL (23U) //!< Bit position for SDHC_PRSSTAT_CLSL. +#define BM_SDHC_PRSSTAT_CLSL (0x00800000U) //!< Bit mask for SDHC_PRSSTAT_CLSL. +#define BS_SDHC_PRSSTAT_CLSL (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CLSL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_CLSL field. +#define BR_SDHC_PRSSTAT_CLSL (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CLSL)) +#endif +//@} + +/*! + * @name Register SDHC_PRSSTAT, field DLSL[31:24] (RO) + * + * Used to check the DAT line level to recover from errors, and for debugging. + * This is especially useful in detecting the busy signal level from DAT[0]. The + * reset value is effected by the external pullup/pulldown resistors. By default, + * the read value of this field after reset is 8'b11110111, when DAT[3] is pulled + * down and the other lines are pulled up. + */ +//@{ +#define BP_SDHC_PRSSTAT_DLSL (24U) //!< Bit position for SDHC_PRSSTAT_DLSL. +#define BM_SDHC_PRSSTAT_DLSL (0xFF000000U) //!< Bit mask for SDHC_PRSSTAT_DLSL. +#define BS_SDHC_PRSSTAT_DLSL (8U) //!< Bit field size in bits for SDHC_PRSSTAT_DLSL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PRSSTAT_DLSL field. +#define BR_SDHC_PRSSTAT_DLSL (HW_SDHC_PRSSTAT.B.DLSL) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_PROCTL - Protocol Control register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_PROCTL - Protocol Control register (RW) + * + * Reset value: 0x00000020U + * + * There are three cases to restart the transfer after stop at the block gap. + * Which case is appropriate depends on whether the SDHC issues a suspend command + * or the SD card accepts the suspend command: If the host driver does not issue a + * suspend command, the continue request shall be used to restart the transfer. + * If the host driver issues a suspend command and the SD card accepts it, a + * resume command shall be used to restart the transfer. If the host driver issues a + * suspend command and the SD card does not accept it, the continue request shall + * be used to restart the transfer. Any time stop at block gap request stops the + * data transfer, the host driver shall wait for a transfer complete (in the + * interrupt status register), before attempting to restart the transfer. When + * restarting the data transfer by continue request, the host driver shall clear the + * stop at block gap request before or simultaneously. + */ +typedef union _hw_sdhc_proctl +{ + uint32_t U; + struct _hw_sdhc_proctl_bitfields + { + uint32_t LCTL : 1; //!< [0] LED Control + uint32_t DTW : 2; //!< [2:1] Data Transfer Width + uint32_t D3CD : 1; //!< [3] DAT3 As Card Detection Pin + uint32_t EMODE : 2; //!< [5:4] Endian Mode + uint32_t CDTL : 1; //!< [6] Card Detect Test Level + uint32_t CDSS : 1; //!< [7] Card Detect Signal Selection + uint32_t DMAS : 2; //!< [9:8] DMA Select + uint32_t RESERVED0 : 6; //!< [15:10] + uint32_t SABGREQ : 1; //!< [16] Stop At Block Gap Request + uint32_t CREQ : 1; //!< [17] Continue Request + uint32_t RWCTL : 1; //!< [18] Read Wait Control + uint32_t IABG : 1; //!< [19] Interrupt At Block Gap + uint32_t RESERVED1 : 4; //!< [23:20] + uint32_t WECINT : 1; //!< [24] Wakeup Event Enable On Card Interrupt + uint32_t WECINS : 1; //!< [25] Wakeup Event Enable On SD Card + //! Insertion + uint32_t WECRM : 1; //!< [26] Wakeup Event Enable On SD Card Removal + uint32_t RESERVED2 : 5; //!< [31:27] + } B; +} hw_sdhc_proctl_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_PROCTL register + */ +//@{ +#define HW_SDHC_PROCTL_ADDR (REGS_SDHC_BASE + 0x28U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_PROCTL (*(__IO hw_sdhc_proctl_t *) HW_SDHC_PROCTL_ADDR) +#define HW_SDHC_PROCTL_RD() (HW_SDHC_PROCTL.U) +#define HW_SDHC_PROCTL_WR(v) (HW_SDHC_PROCTL.U = (v)) +#define HW_SDHC_PROCTL_SET(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() | (v))) +#define HW_SDHC_PROCTL_CLR(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() & ~(v))) +#define HW_SDHC_PROCTL_TOG(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_PROCTL bitfields + */ + +/*! + * @name Register SDHC_PROCTL, field LCTL[0] (RW) + * + * This bit, fully controlled by the host driver, is used to caution the user + * not to remove the card while the card is being accessed. If the software is + * going to issue multiple SD commands, this bit can be set during all these + * transactions. It is not necessary to change for each transaction. When the software + * issues multiple SD commands, setting the bit once before the first command is + * sufficient: it is not necessary to reset the bit between commands. + * + * Values: + * - 0 - LED off. + * - 1 - LED on. + */ +//@{ +#define BP_SDHC_PROCTL_LCTL (0U) //!< Bit position for SDHC_PROCTL_LCTL. +#define BM_SDHC_PROCTL_LCTL (0x00000001U) //!< Bit mask for SDHC_PROCTL_LCTL. +#define BS_SDHC_PROCTL_LCTL (1U) //!< Bit field size in bits for SDHC_PROCTL_LCTL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_LCTL field. +#define BR_SDHC_PROCTL_LCTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_LCTL)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_LCTL. +#define BF_SDHC_PROCTL_LCTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_LCTL), uint32_t) & BM_SDHC_PROCTL_LCTL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the LCTL field to a new value. +#define BW_SDHC_PROCTL_LCTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_LCTL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field DTW[2:1] (RW) + * + * Selects the data width of the SD bus for a data transfer. The host driver + * shall set it to match the data width of the card. Possible data transfer width is + * 1-bit, 4-bits or 8-bits. + * + * Values: + * - 00 - 1-bit mode + * - 01 - 4-bit mode + * - 10 - 8-bit mode + * - 11 - Reserved + */ +//@{ +#define BP_SDHC_PROCTL_DTW (1U) //!< Bit position for SDHC_PROCTL_DTW. +#define BM_SDHC_PROCTL_DTW (0x00000006U) //!< Bit mask for SDHC_PROCTL_DTW. +#define BS_SDHC_PROCTL_DTW (2U) //!< Bit field size in bits for SDHC_PROCTL_DTW. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_DTW field. +#define BR_SDHC_PROCTL_DTW (HW_SDHC_PROCTL.B.DTW) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_DTW. +#define BF_SDHC_PROCTL_DTW(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_DTW), uint32_t) & BM_SDHC_PROCTL_DTW) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTW field to a new value. +#define BW_SDHC_PROCTL_DTW(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_DTW) | BF_SDHC_PROCTL_DTW(v))) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field D3CD[3] (RW) + * + * If this bit is set, DAT3 should be pulled down to act as a card detection + * pin. Be cautious when using this feature, because DAT3 is also a chip-select for + * the SPI mode. A pulldown on this pin and CMD0 may set the card into the SPI + * mode, which the SDHC does not support. Note: Keep this bit set if SDIO interrupt + * is used. + * + * Values: + * - 0 - DAT3 does not monitor card Insertion. + * - 1 - DAT3 as card detection pin. + */ +//@{ +#define BP_SDHC_PROCTL_D3CD (3U) //!< Bit position for SDHC_PROCTL_D3CD. +#define BM_SDHC_PROCTL_D3CD (0x00000008U) //!< Bit mask for SDHC_PROCTL_D3CD. +#define BS_SDHC_PROCTL_D3CD (1U) //!< Bit field size in bits for SDHC_PROCTL_D3CD. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_D3CD field. +#define BR_SDHC_PROCTL_D3CD (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_D3CD)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_D3CD. +#define BF_SDHC_PROCTL_D3CD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_D3CD), uint32_t) & BM_SDHC_PROCTL_D3CD) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the D3CD field to a new value. +#define BW_SDHC_PROCTL_D3CD(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_D3CD) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field EMODE[5:4] (RW) + * + * The SDHC supports all four endian modes in data transfer. + * + * Values: + * - 00 - Big endian mode + * - 01 - Half word big endian mode + * - 10 - Little endian mode + * - 11 - Reserved + */ +//@{ +#define BP_SDHC_PROCTL_EMODE (4U) //!< Bit position for SDHC_PROCTL_EMODE. +#define BM_SDHC_PROCTL_EMODE (0x00000030U) //!< Bit mask for SDHC_PROCTL_EMODE. +#define BS_SDHC_PROCTL_EMODE (2U) //!< Bit field size in bits for SDHC_PROCTL_EMODE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_EMODE field. +#define BR_SDHC_PROCTL_EMODE (HW_SDHC_PROCTL.B.EMODE) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_EMODE. +#define BF_SDHC_PROCTL_EMODE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_EMODE), uint32_t) & BM_SDHC_PROCTL_EMODE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the EMODE field to a new value. +#define BW_SDHC_PROCTL_EMODE(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_EMODE) | BF_SDHC_PROCTL_EMODE(v))) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field CDTL[6] (RW) + * + * Enabled while the CDSS is set to 1 and it indicates card insertion. + * + * Values: + * - 0 - Card detect test level is 0, no card inserted. + * - 1 - Card detect test level is 1, card inserted. + */ +//@{ +#define BP_SDHC_PROCTL_CDTL (6U) //!< Bit position for SDHC_PROCTL_CDTL. +#define BM_SDHC_PROCTL_CDTL (0x00000040U) //!< Bit mask for SDHC_PROCTL_CDTL. +#define BS_SDHC_PROCTL_CDTL (1U) //!< Bit field size in bits for SDHC_PROCTL_CDTL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_CDTL field. +#define BR_SDHC_PROCTL_CDTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDTL)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_CDTL. +#define BF_SDHC_PROCTL_CDTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CDTL), uint32_t) & BM_SDHC_PROCTL_CDTL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CDTL field to a new value. +#define BW_SDHC_PROCTL_CDTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDTL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field CDSS[7] (RW) + * + * Selects the source for the card detection. + * + * Values: + * - 0 - Card detection level is selected for normal purpose. + * - 1 - Card detection test level is selected for test purpose. + */ +//@{ +#define BP_SDHC_PROCTL_CDSS (7U) //!< Bit position for SDHC_PROCTL_CDSS. +#define BM_SDHC_PROCTL_CDSS (0x00000080U) //!< Bit mask for SDHC_PROCTL_CDSS. +#define BS_SDHC_PROCTL_CDSS (1U) //!< Bit field size in bits for SDHC_PROCTL_CDSS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_CDSS field. +#define BR_SDHC_PROCTL_CDSS (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDSS)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_CDSS. +#define BF_SDHC_PROCTL_CDSS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CDSS), uint32_t) & BM_SDHC_PROCTL_CDSS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CDSS field to a new value. +#define BW_SDHC_PROCTL_CDSS(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDSS) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field DMAS[9:8] (RW) + * + * This field is valid while DMA (SDMA or ADMA) is enabled and selects the DMA + * operation. + * + * Values: + * - 00 - No DMA or simple DMA is selected. + * - 01 - ADMA1 is selected. + * - 10 - ADMA2 is selected. + * - 11 - Reserved + */ +//@{ +#define BP_SDHC_PROCTL_DMAS (8U) //!< Bit position for SDHC_PROCTL_DMAS. +#define BM_SDHC_PROCTL_DMAS (0x00000300U) //!< Bit mask for SDHC_PROCTL_DMAS. +#define BS_SDHC_PROCTL_DMAS (2U) //!< Bit field size in bits for SDHC_PROCTL_DMAS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_DMAS field. +#define BR_SDHC_PROCTL_DMAS (HW_SDHC_PROCTL.B.DMAS) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_DMAS. +#define BF_SDHC_PROCTL_DMAS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_DMAS), uint32_t) & BM_SDHC_PROCTL_DMAS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAS field to a new value. +#define BW_SDHC_PROCTL_DMAS(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_DMAS) | BF_SDHC_PROCTL_DMAS(v))) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field SABGREQ[16] (RW) + * + * Used to stop executing a transaction at the next block gap for both DMA and + * non-DMA transfers. Until the IRQSTATEN[TCSEN] is set to 1, indicating a + * transfer completion, the host driver shall leave this bit set to 1. Clearing both + * PROCTL[SABGREQ] and PROCTL[CREQ] does not cause the transaction to restart. Read + * Wait is used to stop the read transaction at the block gap. The SDHC will + * honor the PROCTL[SABGREQ] for write transfers, but for read transfers it requires + * that SDIO card support read wait. Therefore, the host driver shall not set + * this bit during read transfers unless the SDIO card supports read wait and has + * set PROCTL[RWCTL] to 1, otherwise the SDHC will stop the SD bus clock to pause + * the read operation during block gap. In the case of write transfers in which + * the host driver writes data to the data port register, the host driver shall set + * this bit after all block data is written. If this bit is set to 1, the host + * driver shall not write data to the Data Port register after a block is sent. + * Once this bit is set, the host driver shall not clear this bit before + * IRQSTATEN[TCSEN] is set, otherwise the SDHC's behavior is undefined. This bit effects + * PRSSTAT[RTA], PRSSTAT[WTA], and PRSSTAT[CDIHB]. + * + * Values: + * - 0 - Transfer + * - 1 - Stop + */ +//@{ +#define BP_SDHC_PROCTL_SABGREQ (16U) //!< Bit position for SDHC_PROCTL_SABGREQ. +#define BM_SDHC_PROCTL_SABGREQ (0x00010000U) //!< Bit mask for SDHC_PROCTL_SABGREQ. +#define BS_SDHC_PROCTL_SABGREQ (1U) //!< Bit field size in bits for SDHC_PROCTL_SABGREQ. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_SABGREQ field. +#define BR_SDHC_PROCTL_SABGREQ (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_SABGREQ)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_SABGREQ. +#define BF_SDHC_PROCTL_SABGREQ(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_SABGREQ), uint32_t) & BM_SDHC_PROCTL_SABGREQ) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the SABGREQ field to a new value. +#define BW_SDHC_PROCTL_SABGREQ(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_SABGREQ) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field CREQ[17] (RW) + * + * Used to restart a transaction which was stopped using the PROCTL[SABGREQ]. + * When a suspend operation is not accepted by the card, it is also by setting this + * bit to restart the paused transfer. To cancel stop at the block gap, set + * PROCTL[SABGREQ] to 0 and set this bit to 1 to restart the transfer. The SDHC + * automatically clears this bit, therefore it is not necessary for the host driver to + * set this bit to 0. If both PROCTL[SABGREQ] and this bit are 1, the continue + * request is ignored. + * + * Values: + * - 0 - No effect. + * - 1 - Restart + */ +//@{ +#define BP_SDHC_PROCTL_CREQ (17U) //!< Bit position for SDHC_PROCTL_CREQ. +#define BM_SDHC_PROCTL_CREQ (0x00020000U) //!< Bit mask for SDHC_PROCTL_CREQ. +#define BS_SDHC_PROCTL_CREQ (1U) //!< Bit field size in bits for SDHC_PROCTL_CREQ. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_CREQ field. +#define BR_SDHC_PROCTL_CREQ (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CREQ)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_CREQ. +#define BF_SDHC_PROCTL_CREQ(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CREQ), uint32_t) & BM_SDHC_PROCTL_CREQ) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CREQ field to a new value. +#define BW_SDHC_PROCTL_CREQ(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CREQ) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field RWCTL[18] (RW) + * + * The read wait function is optional for SDIO cards. If the card supports read + * wait, set this bit to enable use of the read wait protocol to stop read data + * using the DAT[2] line. Otherwise, the SDHC has to stop the SD Clock to hold + * read data, which restricts commands generation. When the host driver detects an + * SDIO card insertion, it shall set this bit according to the CCCR of the card. + * If the card does not support read wait, this bit shall never be set to 1, + * otherwise DAT line conflicts may occur. If this bit is set to 0, stop at block gap + * during read operation is also supported, but the SDHC will stop the SD Clock + * to pause reading operation. + * + * Values: + * - 0 - Disable read wait control, and stop SD clock at block gap when SABGREQ + * is set. + * - 1 - Enable read wait control, and assert read wait without stopping SD + * clock at block gap when SABGREQ bit is set. + */ +//@{ +#define BP_SDHC_PROCTL_RWCTL (18U) //!< Bit position for SDHC_PROCTL_RWCTL. +#define BM_SDHC_PROCTL_RWCTL (0x00040000U) //!< Bit mask for SDHC_PROCTL_RWCTL. +#define BS_SDHC_PROCTL_RWCTL (1U) //!< Bit field size in bits for SDHC_PROCTL_RWCTL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_RWCTL field. +#define BR_SDHC_PROCTL_RWCTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_RWCTL)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_RWCTL. +#define BF_SDHC_PROCTL_RWCTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_RWCTL), uint32_t) & BM_SDHC_PROCTL_RWCTL) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RWCTL field to a new value. +#define BW_SDHC_PROCTL_RWCTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_RWCTL) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field IABG[19] (RW) + * + * Valid only in 4-bit mode, of the SDIO card, and selects a sample point in the + * interrupt cycle. Setting to 1 enables interrupt detection at the block gap + * for a multiple block transfer. Setting to 0 disables interrupt detection during + * a multiple block transfer. If the SDIO card can't signal an interrupt during a + * multiple block transfer, this bit must be set to 0 to avoid an inadvertent + * interrupt. When the host driver detects an SDIO card insertion, it shall set + * this bit according to the CCCR of the card. + * + * Values: + * - 0 - Disabled + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_PROCTL_IABG (19U) //!< Bit position for SDHC_PROCTL_IABG. +#define BM_SDHC_PROCTL_IABG (0x00080000U) //!< Bit mask for SDHC_PROCTL_IABG. +#define BS_SDHC_PROCTL_IABG (1U) //!< Bit field size in bits for SDHC_PROCTL_IABG. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_IABG field. +#define BR_SDHC_PROCTL_IABG (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_IABG)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_IABG. +#define BF_SDHC_PROCTL_IABG(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_IABG), uint32_t) & BM_SDHC_PROCTL_IABG) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the IABG field to a new value. +#define BW_SDHC_PROCTL_IABG(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_IABG) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field WECINT[24] (RW) + * + * Enables a wakeup event, via IRQSTAT[CINT]. This bit can be set to 1 if FN_WUS + * (Wake Up Support) in CIS is set to 1. When this bit is set, the card + * interrupt status and the SDHC interrupt can be asserted without SD_CLK toggling. When + * the wakeup feature is not enabled, the SD_CLK must be active to assert the + * card interrupt status and the SDHC interrupt. + * + * Values: + * - 0 - Disabled + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_PROCTL_WECINT (24U) //!< Bit position for SDHC_PROCTL_WECINT. +#define BM_SDHC_PROCTL_WECINT (0x01000000U) //!< Bit mask for SDHC_PROCTL_WECINT. +#define BS_SDHC_PROCTL_WECINT (1U) //!< Bit field size in bits for SDHC_PROCTL_WECINT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_WECINT field. +#define BR_SDHC_PROCTL_WECINT (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINT)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_WECINT. +#define BF_SDHC_PROCTL_WECINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECINT), uint32_t) & BM_SDHC_PROCTL_WECINT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the WECINT field to a new value. +#define BW_SDHC_PROCTL_WECINT(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINT) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field WECINS[25] (RW) + * + * Enables a wakeup event, via IRQSTAT[CINS]. FN_WUS (Wake Up Support) in CIS + * does not effect this bit. When this bit is set, IRQSTATEN[CINSEN] and the SDHC + * interrupt can be asserted without SD_CLK toggling. When the wakeup feature is + * not enabled, the SD_CLK must be active to assert IRQSTATEN[CINSEN] and the SDHC + * interrupt. + * + * Values: + * - 0 - Disabled + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_PROCTL_WECINS (25U) //!< Bit position for SDHC_PROCTL_WECINS. +#define BM_SDHC_PROCTL_WECINS (0x02000000U) //!< Bit mask for SDHC_PROCTL_WECINS. +#define BS_SDHC_PROCTL_WECINS (1U) //!< Bit field size in bits for SDHC_PROCTL_WECINS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_WECINS field. +#define BR_SDHC_PROCTL_WECINS (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINS)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_WECINS. +#define BF_SDHC_PROCTL_WECINS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECINS), uint32_t) & BM_SDHC_PROCTL_WECINS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the WECINS field to a new value. +#define BW_SDHC_PROCTL_WECINS(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINS) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_PROCTL, field WECRM[26] (RW) + * + * Enables a wakeup event, via IRQSTAT[CRM]. FN_WUS (Wake Up Support) in CIS + * does not effect this bit. When this bit is set, IRQSTAT[CRM] and the SDHC + * interrupt can be asserted without SD_CLK toggling. When the wakeup feature is not + * enabled, the SD_CLK must be active to assert IRQSTAT[CRM] and the SDHC interrupt. + * + * Values: + * - 0 - Disabled + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_PROCTL_WECRM (26U) //!< Bit position for SDHC_PROCTL_WECRM. +#define BM_SDHC_PROCTL_WECRM (0x04000000U) //!< Bit mask for SDHC_PROCTL_WECRM. +#define BS_SDHC_PROCTL_WECRM (1U) //!< Bit field size in bits for SDHC_PROCTL_WECRM. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_PROCTL_WECRM field. +#define BR_SDHC_PROCTL_WECRM (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECRM)) +#endif + +//! @brief Format value for bitfield SDHC_PROCTL_WECRM. +#define BF_SDHC_PROCTL_WECRM(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECRM), uint32_t) & BM_SDHC_PROCTL_WECRM) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the WECRM field to a new value. +#define BW_SDHC_PROCTL_WECRM(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECRM) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_SYSCTL - System Control register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_SYSCTL - System Control register (RW) + * + * Reset value: 0x00008008U + */ +typedef union _hw_sdhc_sysctl +{ + uint32_t U; + struct _hw_sdhc_sysctl_bitfields + { + uint32_t IPGEN : 1; //!< [0] IPG Clock Enable + uint32_t HCKEN : 1; //!< [1] System Clock Enable + uint32_t PEREN : 1; //!< [2] Peripheral Clock Enable + uint32_t SDCLKEN : 1; //!< [3] SD Clock Enable + uint32_t DVS : 4; //!< [7:4] Divisor + uint32_t SDCLKFS : 8; //!< [15:8] SDCLK Frequency Select + uint32_t DTOCV : 4; //!< [19:16] Data Timeout Counter Value + uint32_t RESERVED0 : 4; //!< [23:20] + uint32_t RSTA : 1; //!< [24] Software Reset For ALL + uint32_t RSTC : 1; //!< [25] Software Reset For CMD Line + uint32_t RSTD : 1; //!< [26] Software Reset For DAT Line + uint32_t INITA : 1; //!< [27] Initialization Active + uint32_t RESERVED1 : 4; //!< [31:28] + } B; +} hw_sdhc_sysctl_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_SYSCTL register + */ +//@{ +#define HW_SDHC_SYSCTL_ADDR (REGS_SDHC_BASE + 0x2CU) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_SYSCTL (*(__IO hw_sdhc_sysctl_t *) HW_SDHC_SYSCTL_ADDR) +#define HW_SDHC_SYSCTL_RD() (HW_SDHC_SYSCTL.U) +#define HW_SDHC_SYSCTL_WR(v) (HW_SDHC_SYSCTL.U = (v)) +#define HW_SDHC_SYSCTL_SET(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() | (v))) +#define HW_SDHC_SYSCTL_CLR(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() & ~(v))) +#define HW_SDHC_SYSCTL_TOG(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_SYSCTL bitfields + */ + +/*! + * @name Register SDHC_SYSCTL, field IPGEN[0] (RW) + * + * If this bit is set, bus clock will always be active and no automatic gating + * is applied. The bus clock will be internally gated off, if none of the + * following factors are met: The cmd part is reset, or Data part is reset, or Soft + * reset, or The cmd is about to send, or Clock divisor is just updated, or Continue + * request is just set, or This bit is set, or Card insertion is detected, or Card + * removal is detected, or Card external interrupt is detected, or The SDHC + * clock is not gated off The bus clock will not be auto gated off if the SDHC clock + * is not gated off. So clearing only this bit has no effect unless the PEREN bit + * is also cleared. + * + * Values: + * - 0 - Bus clock will be internally gated off. + * - 1 - Bus clock will not be automatically gated off. + */ +//@{ +#define BP_SDHC_SYSCTL_IPGEN (0U) //!< Bit position for SDHC_SYSCTL_IPGEN. +#define BM_SDHC_SYSCTL_IPGEN (0x00000001U) //!< Bit mask for SDHC_SYSCTL_IPGEN. +#define BS_SDHC_SYSCTL_IPGEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_IPGEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_IPGEN field. +#define BR_SDHC_SYSCTL_IPGEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_IPGEN)) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_IPGEN. +#define BF_SDHC_SYSCTL_IPGEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_IPGEN), uint32_t) & BM_SDHC_SYSCTL_IPGEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the IPGEN field to a new value. +#define BW_SDHC_SYSCTL_IPGEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_IPGEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field HCKEN[1] (RW) + * + * If this bit is set, system clock will always be active and no automatic + * gating is applied. When this bit is cleared, system clock will be automatically off + * when no data transfer is on the SD bus. + * + * Values: + * - 0 - System clock will be internally gated off. + * - 1 - System clock will not be automatically gated off. + */ +//@{ +#define BP_SDHC_SYSCTL_HCKEN (1U) //!< Bit position for SDHC_SYSCTL_HCKEN. +#define BM_SDHC_SYSCTL_HCKEN (0x00000002U) //!< Bit mask for SDHC_SYSCTL_HCKEN. +#define BS_SDHC_SYSCTL_HCKEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_HCKEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_HCKEN field. +#define BR_SDHC_SYSCTL_HCKEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_HCKEN)) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_HCKEN. +#define BF_SDHC_SYSCTL_HCKEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_HCKEN), uint32_t) & BM_SDHC_SYSCTL_HCKEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the HCKEN field to a new value. +#define BW_SDHC_SYSCTL_HCKEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_HCKEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field PEREN[2] (RW) + * + * If this bit is set, SDHC clock will always be active and no automatic gating + * is applied. Thus the SDCLK is active except for when auto gating-off during + * buffer danger (buffer about to over-run or under-run). When this bit is cleared, + * the SDHC clock will be automatically off whenever there is no transaction on + * the SD bus. Because this bit is only a feature enabling bit, clearing this bit + * does not stop SDCLK immediately. The SDHC clock will be internally gated off, + * if none of the following factors are met: The cmd part is reset, or Data part + * is reset, or A soft reset, or The cmd is about to send, or Clock divisor is + * just updated, or Continue request is just set, or This bit is set, or Card + * insertion is detected, or Card removal is detected, or Card external interrupt is + * detected, or 80 clocks for initialization phase is ongoing + * + * Values: + * - 0 - SDHC clock will be internally gated off. + * - 1 - SDHC clock will not be automatically gated off. + */ +//@{ +#define BP_SDHC_SYSCTL_PEREN (2U) //!< Bit position for SDHC_SYSCTL_PEREN. +#define BM_SDHC_SYSCTL_PEREN (0x00000004U) //!< Bit mask for SDHC_SYSCTL_PEREN. +#define BS_SDHC_SYSCTL_PEREN (1U) //!< Bit field size in bits for SDHC_SYSCTL_PEREN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_PEREN field. +#define BR_SDHC_SYSCTL_PEREN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_PEREN)) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_PEREN. +#define BF_SDHC_SYSCTL_PEREN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_PEREN), uint32_t) & BM_SDHC_SYSCTL_PEREN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the PEREN field to a new value. +#define BW_SDHC_SYSCTL_PEREN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_PEREN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field SDCLKEN[3] (RW) + * + * The host controller shall stop SDCLK when writing this bit to 0. SDCLK + * frequency can be changed when this bit is 0. Then, the host controller shall + * maintain the same clock frequency until SDCLK is stopped (stop at SDCLK = 0). If the + * IRQSTAT[CINS] is cleared, this bit must be cleared by the host driver to save + * power. + */ +//@{ +#define BP_SDHC_SYSCTL_SDCLKEN (3U) //!< Bit position for SDHC_SYSCTL_SDCLKEN. +#define BM_SDHC_SYSCTL_SDCLKEN (0x00000008U) //!< Bit mask for SDHC_SYSCTL_SDCLKEN. +#define BS_SDHC_SYSCTL_SDCLKEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_SDCLKEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_SDCLKEN field. +#define BR_SDHC_SYSCTL_SDCLKEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_SDCLKEN)) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_SDCLKEN. +#define BF_SDHC_SYSCTL_SDCLKEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_SDCLKEN), uint32_t) & BM_SDHC_SYSCTL_SDCLKEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the SDCLKEN field to a new value. +#define BW_SDHC_SYSCTL_SDCLKEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_SDCLKEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field DVS[7:4] (RW) + * + * Used to provide a more exact divisor to generate the desired SD clock + * frequency. Note the divider can even support odd divisor without deterioration of + * duty cycle. The setting are as following: + * + * Values: + * - 0 - Divisor by 1. + * - 1 - Divisor by 2. + * - 1110 - Divisor by 15. + * - 1111 - Divisor by 16. + */ +//@{ +#define BP_SDHC_SYSCTL_DVS (4U) //!< Bit position for SDHC_SYSCTL_DVS. +#define BM_SDHC_SYSCTL_DVS (0x000000F0U) //!< Bit mask for SDHC_SYSCTL_DVS. +#define BS_SDHC_SYSCTL_DVS (4U) //!< Bit field size in bits for SDHC_SYSCTL_DVS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_DVS field. +#define BR_SDHC_SYSCTL_DVS (HW_SDHC_SYSCTL.B.DVS) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_DVS. +#define BF_SDHC_SYSCTL_DVS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_DVS), uint32_t) & BM_SDHC_SYSCTL_DVS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DVS field to a new value. +#define BW_SDHC_SYSCTL_DVS(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_DVS) | BF_SDHC_SYSCTL_DVS(v))) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field SDCLKFS[15:8] (RW) + * + * Used to select the frequency of the SDCLK pin. The frequency is not + * programmed directly. Rather this register holds the prescaler (this register) and + * divisor (next register) of the base clock frequency register. Setting 00h bypasses + * the frequency prescaler of the SD Clock. Multiple bits must not be set, or the + * behavior of this prescaler is undefined. The two default divider values can + * be calculated by the frequency of SDHC clock and the following divisor bits. + * The frequency of SDCLK is set by the following formula: Clock frequency = (Base + * clock) / (prescaler x divisor) For example, if the base clock frequency is 96 + * MHz, and the target frequency is 25 MHz, then choosing the prescaler value of + * 01h and divisor value of 1h will yield 24 MHz, which is the nearest frequency + * less than or equal to the target. Similarly, to approach a clock value of 400 + * kHz, the prescaler value of 08h and divisor value of eh yields the exact clock + * value of 400 kHz. The reset value of this field is 80h, so if the input base + * clock ( SDHC clock ) is about 96 MHz, the default SD clock after reset is 375 + * kHz. According to the SD Physical Specification Version 1.1 and the SDIO Card + * Specification Version 1.2, the maximum SD clock frequency is 50 MHz and shall + * never exceed this limit. Only the following settings are allowed: + * + * Values: + * - 1 - Base clock divided by 2. + * - 10 - Base clock divided by 4. + * - 100 - Base clock divided by 8. + * - 1000 - Base clock divided by 16. + * - 10000 - Base clock divided by 32. + * - 100000 - Base clock divided by 64. + * - 1000000 - Base clock divided by 128. + * - 10000000 - Base clock divided by 256. + */ +//@{ +#define BP_SDHC_SYSCTL_SDCLKFS (8U) //!< Bit position for SDHC_SYSCTL_SDCLKFS. +#define BM_SDHC_SYSCTL_SDCLKFS (0x0000FF00U) //!< Bit mask for SDHC_SYSCTL_SDCLKFS. +#define BS_SDHC_SYSCTL_SDCLKFS (8U) //!< Bit field size in bits for SDHC_SYSCTL_SDCLKFS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_SDCLKFS field. +#define BR_SDHC_SYSCTL_SDCLKFS (HW_SDHC_SYSCTL.B.SDCLKFS) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_SDCLKFS. +#define BF_SDHC_SYSCTL_SDCLKFS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_SDCLKFS), uint32_t) & BM_SDHC_SYSCTL_SDCLKFS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the SDCLKFS field to a new value. +#define BW_SDHC_SYSCTL_SDCLKFS(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_SDCLKFS) | BF_SDHC_SYSCTL_SDCLKFS(v))) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field DTOCV[19:16] (RW) + * + * Determines the interval by which DAT line timeouts are detected. See + * IRQSTAT[DTOE] for information on factors that dictate time-out generation. Time-out + * clock frequency will be generated by dividing the base clock SDCLK value by this + * value. The host driver can clear IRQSTATEN[DTOESEN] to prevent inadvertent + * time-out events. + * + * Values: + * - 0000 - SDCLK x 2 13 + * - 0001 - SDCLK x 2 14 + * - 1110 - SDCLK x 2 27 + * - 1111 - Reserved + */ +//@{ +#define BP_SDHC_SYSCTL_DTOCV (16U) //!< Bit position for SDHC_SYSCTL_DTOCV. +#define BM_SDHC_SYSCTL_DTOCV (0x000F0000U) //!< Bit mask for SDHC_SYSCTL_DTOCV. +#define BS_SDHC_SYSCTL_DTOCV (4U) //!< Bit field size in bits for SDHC_SYSCTL_DTOCV. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_DTOCV field. +#define BR_SDHC_SYSCTL_DTOCV (HW_SDHC_SYSCTL.B.DTOCV) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_DTOCV. +#define BF_SDHC_SYSCTL_DTOCV(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_DTOCV), uint32_t) & BM_SDHC_SYSCTL_DTOCV) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOCV field to a new value. +#define BW_SDHC_SYSCTL_DTOCV(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_DTOCV) | BF_SDHC_SYSCTL_DTOCV(v))) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field RSTA[24] (WORZ) + * + * Effects the entire host controller except for the card detection circuit. + * Register bits of type ROC, RW, RW1C, RWAC are cleared. During its initialization, + * the host driver shall set this bit to 1 to reset the SDHC. The SDHC shall + * reset this bit to 0 when the capabilities registers are valid and the host driver + * can read them. Additional use of software reset for all does not affect the + * value of the capabilities registers. After this bit is set, it is recommended + * that the host driver reset the external card and reinitialize it. + * + * Values: + * - 0 - No reset. + * - 1 - Reset. + */ +//@{ +#define BP_SDHC_SYSCTL_RSTA (24U) //!< Bit position for SDHC_SYSCTL_RSTA. +#define BM_SDHC_SYSCTL_RSTA (0x01000000U) //!< Bit mask for SDHC_SYSCTL_RSTA. +#define BS_SDHC_SYSCTL_RSTA (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTA. + +//! @brief Format value for bitfield SDHC_SYSCTL_RSTA. +#define BF_SDHC_SYSCTL_RSTA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTA), uint32_t) & BM_SDHC_SYSCTL_RSTA) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RSTA field to a new value. +#define BW_SDHC_SYSCTL_RSTA(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTA) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field RSTC[25] (WORZ) + * + * Only part of the command circuit is reset. The following registers and bits + * are cleared by this bit: PRSSTAT[CIHB] IRQSTAT[CC] + * + * Values: + * - 0 - No reset. + * - 1 - Reset. + */ +//@{ +#define BP_SDHC_SYSCTL_RSTC (25U) //!< Bit position for SDHC_SYSCTL_RSTC. +#define BM_SDHC_SYSCTL_RSTC (0x02000000U) //!< Bit mask for SDHC_SYSCTL_RSTC. +#define BS_SDHC_SYSCTL_RSTC (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTC. + +//! @brief Format value for bitfield SDHC_SYSCTL_RSTC. +#define BF_SDHC_SYSCTL_RSTC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTC), uint32_t) & BM_SDHC_SYSCTL_RSTC) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RSTC field to a new value. +#define BW_SDHC_SYSCTL_RSTC(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTC) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field RSTD[26] (WORZ) + * + * Only part of the data circuit is reset. DMA circuit is also reset. The + * following registers and bits are cleared by this bit: Data Port register Buffer Is + * Cleared And Initialized.Present State register Buffer Read Enable Buffer Write + * Enable Read Transfer Active Write Transfer Active DAT Line Active Command + * Inhibit (DAT) Protocol Control register Continue Request Stop At Block Gap Request + * Interrupt Status register Buffer Read Ready Buffer Write Ready DMA Interrupt + * Block Gap Event Transfer Complete + * + * Values: + * - 0 - No reset. + * - 1 - Reset. + */ +//@{ +#define BP_SDHC_SYSCTL_RSTD (26U) //!< Bit position for SDHC_SYSCTL_RSTD. +#define BM_SDHC_SYSCTL_RSTD (0x04000000U) //!< Bit mask for SDHC_SYSCTL_RSTD. +#define BS_SDHC_SYSCTL_RSTD (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTD. + +//! @brief Format value for bitfield SDHC_SYSCTL_RSTD. +#define BF_SDHC_SYSCTL_RSTD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTD), uint32_t) & BM_SDHC_SYSCTL_RSTD) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RSTD field to a new value. +#define BW_SDHC_SYSCTL_RSTD(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTD) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_SYSCTL, field INITA[27] (RW) + * + * When this bit is set, 80 SD-clocks are sent to the card. After the 80 clocks + * are sent, this bit is self-cleared. This bit is very useful during the card + * power-up period when 74 SD-clocks are needed and the clock auto gating feature + * is enabled. Writing 1 to this bit when this bit is already 1 has no effect. + * Writing 0 to this bit at any time has no effect. When either of the PRSSTAT[CIHB] + * and PRSSTAT[CDIHB] bits are set, writing 1 to this bit is ignored, that is, + * when command line or data lines are active, write to this bit is not allowed. + * On the otherhand, when this bit is set, that is, during intialization active + * period, it is allowed to issue command, and the command bit stream will appear + * on the CMD pad after all 80 clock cycles are done. So when this command ends, + * the driver can make sure the 80 clock cycles are sent out. This is very useful + * when the driver needs send 80 cycles to the card and does not want to wait + * till this bit is self-cleared. + */ +//@{ +#define BP_SDHC_SYSCTL_INITA (27U) //!< Bit position for SDHC_SYSCTL_INITA. +#define BM_SDHC_SYSCTL_INITA (0x08000000U) //!< Bit mask for SDHC_SYSCTL_INITA. +#define BS_SDHC_SYSCTL_INITA (1U) //!< Bit field size in bits for SDHC_SYSCTL_INITA. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_SYSCTL_INITA field. +#define BR_SDHC_SYSCTL_INITA (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_INITA)) +#endif + +//! @brief Format value for bitfield SDHC_SYSCTL_INITA. +#define BF_SDHC_SYSCTL_INITA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_INITA), uint32_t) & BM_SDHC_SYSCTL_INITA) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the INITA field to a new value. +#define BW_SDHC_SYSCTL_INITA(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_INITA) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_IRQSTAT - Interrupt Status register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_IRQSTAT - Interrupt Status register (RW) + * + * Reset value: 0x00000000U + * + * An interrupt is generated when the Normal Interrupt Signal Enable is enabled + * and at least one of the status bits is set to 1. For all bits, writing 1 to a + * bit clears it; writing to 0 keeps the bit unchanged. More than one status can + * be cleared with a single register write. For Card Interrupt, before writing 1 + * to clear, it is required that the card stops asserting the interrupt, meaning + * that when the Card Driver services the interrupt condition, otherwise the CINT + * bit will be asserted again. The table below shows the relationship between + * the CTOE and the CC bits. SDHC status for CTOE/CC bit combinations Command + * complete Command timeout error Meaning of the status 0 0 X X 1 Response not + * received within 64 SDCLK cycles 1 0 Response received The table below shows the + * relationship between the Transfer Complete and the Data Timeout Error. SDHC status + * for data timeout error/transfer complete bit combinations Transfer complete + * Data timeout error Meaning of the status 0 0 X 0 1 Timeout occurred during + * transfer 1 X Data transfer complete The table below shows the relationship between + * the command CRC Error (CCE) and Command Timeout Error (CTOE). SDHC status for + * CCE/CTOE Bit Combinations Command complete Command timeout error Meaning of + * the status 0 0 No error 0 1 Response timeout error 1 0 Response CRC error 1 1 + * CMD line conflict + */ +typedef union _hw_sdhc_irqstat +{ + uint32_t U; + struct _hw_sdhc_irqstat_bitfields + { + uint32_t CC : 1; //!< [0] Command Complete + uint32_t TC : 1; //!< [1] Transfer Complete + uint32_t BGE : 1; //!< [2] Block Gap Event + uint32_t DINT : 1; //!< [3] DMA Interrupt + uint32_t BWR : 1; //!< [4] Buffer Write Ready + uint32_t BRR : 1; //!< [5] Buffer Read Ready + uint32_t CINS : 1; //!< [6] Card Insertion + uint32_t CRM : 1; //!< [7] Card Removal + uint32_t CINT : 1; //!< [8] Card Interrupt + uint32_t RESERVED0 : 7; //!< [15:9] + uint32_t CTOE : 1; //!< [16] Command Timeout Error + uint32_t CCE : 1; //!< [17] Command CRC Error + uint32_t CEBE : 1; //!< [18] Command End Bit Error + uint32_t CIE : 1; //!< [19] Command Index Error + uint32_t DTOE : 1; //!< [20] Data Timeout Error + uint32_t DCE : 1; //!< [21] Data CRC Error + uint32_t DEBE : 1; //!< [22] Data End Bit Error + uint32_t RESERVED1 : 1; //!< [23] + uint32_t AC12E : 1; //!< [24] Auto CMD12 Error + uint32_t RESERVED2 : 3; //!< [27:25] + uint32_t DMAE : 1; //!< [28] DMA Error + uint32_t RESERVED3 : 3; //!< [31:29] + } B; +} hw_sdhc_irqstat_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_IRQSTAT register + */ +//@{ +#define HW_SDHC_IRQSTAT_ADDR (REGS_SDHC_BASE + 0x30U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_IRQSTAT (*(__IO hw_sdhc_irqstat_t *) HW_SDHC_IRQSTAT_ADDR) +#define HW_SDHC_IRQSTAT_RD() (HW_SDHC_IRQSTAT.U) +#define HW_SDHC_IRQSTAT_WR(v) (HW_SDHC_IRQSTAT.U = (v)) +#define HW_SDHC_IRQSTAT_SET(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() | (v))) +#define HW_SDHC_IRQSTAT_CLR(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() & ~(v))) +#define HW_SDHC_IRQSTAT_TOG(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_IRQSTAT bitfields + */ + +/*! + * @name Register SDHC_IRQSTAT, field CC[0] (W1C) + * + * This bit is set when you receive the end bit of the command response, except + * Auto CMD12. See PRSSTAT[CIHB]. + * + * Values: + * - 0 - Command not complete. + * - 1 - Command complete. + */ +//@{ +#define BP_SDHC_IRQSTAT_CC (0U) //!< Bit position for SDHC_IRQSTAT_CC. +#define BM_SDHC_IRQSTAT_CC (0x00000001U) //!< Bit mask for SDHC_IRQSTAT_CC. +#define BS_SDHC_IRQSTAT_CC (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CC. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CC field. +#define BR_SDHC_IRQSTAT_CC (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CC)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CC. +#define BF_SDHC_IRQSTAT_CC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CC), uint32_t) & BM_SDHC_IRQSTAT_CC) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CC field to a new value. +#define BW_SDHC_IRQSTAT_CC(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CC) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field TC[1] (W1C) + * + * This bit is set when a read or write transfer is completed. In the case of a + * read transaction: This bit is set at the falling edge of the read transfer + * active status. There are two cases in which this interrupt is generated. The + * first is when a data transfer is completed as specified by the data length, after + * the last data has been read to the host system. The second is when data has + * stopped at the block gap and completed the data transfer by setting + * PROCTL[SABGREQ], after valid data has been read to the host system. In the case of a write + * transaction: This bit is set at the falling edge of the DAT line active + * status. There are two cases in which this interrupt is generated. The first is when + * the last data is written to the SD card as specified by the data length and + * the busy signal is released. The second is when data transfers are stopped at + * the block gap, by setting PROCTL[SABGREQ], and the data transfers are + * completed,after valid data is written to the SD card and the busy signal released. + * + * Values: + * - 0 - Transfer not complete. + * - 1 - Transfer complete. + */ +//@{ +#define BP_SDHC_IRQSTAT_TC (1U) //!< Bit position for SDHC_IRQSTAT_TC. +#define BM_SDHC_IRQSTAT_TC (0x00000002U) //!< Bit mask for SDHC_IRQSTAT_TC. +#define BS_SDHC_IRQSTAT_TC (1U) //!< Bit field size in bits for SDHC_IRQSTAT_TC. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_TC field. +#define BR_SDHC_IRQSTAT_TC (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_TC)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_TC. +#define BF_SDHC_IRQSTAT_TC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_TC), uint32_t) & BM_SDHC_IRQSTAT_TC) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the TC field to a new value. +#define BW_SDHC_IRQSTAT_TC(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_TC) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field BGE[2] (W1C) + * + * If PROCTL[SABGREQ] is set, this bit is set when a read or write transaction + * is stopped at a block gap. If PROCTL[SABGREQ] is not set to 1, this bit is not + * set to 1. In the case of a read transaction: This bit is set at the falling + * edge of the DAT line active status, when the transaction is stopped at SD Bus + * timing. The read wait must be supported in order to use this function. In the + * case of write transaction: This bit is set at the falling edge of write transfer + * active status, after getting CRC status at SD bus timing. + * + * Values: + * - 0 - No block gap event. + * - 1 - Transaction stopped at block gap. + */ +//@{ +#define BP_SDHC_IRQSTAT_BGE (2U) //!< Bit position for SDHC_IRQSTAT_BGE. +#define BM_SDHC_IRQSTAT_BGE (0x00000004U) //!< Bit mask for SDHC_IRQSTAT_BGE. +#define BS_SDHC_IRQSTAT_BGE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BGE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_BGE field. +#define BR_SDHC_IRQSTAT_BGE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BGE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_BGE. +#define BF_SDHC_IRQSTAT_BGE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BGE), uint32_t) & BM_SDHC_IRQSTAT_BGE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BGE field to a new value. +#define BW_SDHC_IRQSTAT_BGE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BGE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field DINT[3] (W1C) + * + * Occurs only when the internal DMA finishes the data transfer successfully. + * Whenever errors occur during data transfer, this bit will not be set. Instead, + * the DMAE bit will be set. Either Simple DMA or ADMA finishes data transferring, + * this bit will be set. + * + * Values: + * - 0 - No DMA Interrupt. + * - 1 - DMA Interrupt is generated. + */ +//@{ +#define BP_SDHC_IRQSTAT_DINT (3U) //!< Bit position for SDHC_IRQSTAT_DINT. +#define BM_SDHC_IRQSTAT_DINT (0x00000008U) //!< Bit mask for SDHC_IRQSTAT_DINT. +#define BS_SDHC_IRQSTAT_DINT (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DINT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_DINT field. +#define BR_SDHC_IRQSTAT_DINT (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DINT)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_DINT. +#define BF_SDHC_IRQSTAT_DINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DINT), uint32_t) & BM_SDHC_IRQSTAT_DINT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DINT field to a new value. +#define BW_SDHC_IRQSTAT_DINT(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DINT) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field BWR[4] (W1C) + * + * This status bit is set if the Buffer Write Enable bit, in the Present State + * register, changes from 0 to 1. See the Buffer Write Enable bit in the Present + * State register for additional information. + * + * Values: + * - 0 - Not ready to write buffer. + * - 1 - Ready to write buffer. + */ +//@{ +#define BP_SDHC_IRQSTAT_BWR (4U) //!< Bit position for SDHC_IRQSTAT_BWR. +#define BM_SDHC_IRQSTAT_BWR (0x00000010U) //!< Bit mask for SDHC_IRQSTAT_BWR. +#define BS_SDHC_IRQSTAT_BWR (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BWR. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_BWR field. +#define BR_SDHC_IRQSTAT_BWR (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BWR)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_BWR. +#define BF_SDHC_IRQSTAT_BWR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BWR), uint32_t) & BM_SDHC_IRQSTAT_BWR) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BWR field to a new value. +#define BW_SDHC_IRQSTAT_BWR(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BWR) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field BRR[5] (W1C) + * + * This status bit is set if the Buffer Read Enable bit, in the Present State + * register, changes from 0 to 1. See the Buffer Read Enable bit in the Present + * State register for additional information. + * + * Values: + * - 0 - Not ready to read buffer. + * - 1 - Ready to read buffer. + */ +//@{ +#define BP_SDHC_IRQSTAT_BRR (5U) //!< Bit position for SDHC_IRQSTAT_BRR. +#define BM_SDHC_IRQSTAT_BRR (0x00000020U) //!< Bit mask for SDHC_IRQSTAT_BRR. +#define BS_SDHC_IRQSTAT_BRR (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BRR. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_BRR field. +#define BR_SDHC_IRQSTAT_BRR (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BRR)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_BRR. +#define BF_SDHC_IRQSTAT_BRR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BRR), uint32_t) & BM_SDHC_IRQSTAT_BRR) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BRR field to a new value. +#define BW_SDHC_IRQSTAT_BRR(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BRR) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CINS[6] (W1C) + * + * This status bit is set if the Card Inserted bit in the Present State register + * changes from 0 to 1. When the host driver writes this bit to 1 to clear this + * status, the status of the Card Inserted in the Present State register must be + * confirmed. Because the card state may possibly be changed when the host driver + * clears this bit and the interrupt event may not be generated. When this bit + * is cleared, it will be set again if a card is inserted. To leave it cleared, + * clear the Card Inserted Status Enable bit in Interrupt Status Enable register. + * + * Values: + * - 0 - Card state unstable or removed. + * - 1 - Card inserted. + */ +//@{ +#define BP_SDHC_IRQSTAT_CINS (6U) //!< Bit position for SDHC_IRQSTAT_CINS. +#define BM_SDHC_IRQSTAT_CINS (0x00000040U) //!< Bit mask for SDHC_IRQSTAT_CINS. +#define BS_SDHC_IRQSTAT_CINS (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CINS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CINS field. +#define BR_SDHC_IRQSTAT_CINS (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINS)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CINS. +#define BF_SDHC_IRQSTAT_CINS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CINS), uint32_t) & BM_SDHC_IRQSTAT_CINS) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINS field to a new value. +#define BW_SDHC_IRQSTAT_CINS(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINS) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CRM[7] (W1C) + * + * This status bit is set if the Card Inserted bit in the Present State register + * changes from 1 to 0. When the host driver writes this bit to 1 to clear this + * status, the status of the Card Inserted in the Present State register must be + * confirmed. Because the card state may possibly be changed when the host driver + * clears this bit and the interrupt event may not be generated. When this bit + * is cleared, it will be set again if no card is inserted. To leave it cleared, + * clear the Card Removal Status Enable bit in Interrupt Status Enable register. + * + * Values: + * - 0 - Card state unstable or inserted. + * - 1 - Card removed. + */ +//@{ +#define BP_SDHC_IRQSTAT_CRM (7U) //!< Bit position for SDHC_IRQSTAT_CRM. +#define BM_SDHC_IRQSTAT_CRM (0x00000080U) //!< Bit mask for SDHC_IRQSTAT_CRM. +#define BS_SDHC_IRQSTAT_CRM (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CRM. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CRM field. +#define BR_SDHC_IRQSTAT_CRM (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CRM)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CRM. +#define BF_SDHC_IRQSTAT_CRM(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CRM), uint32_t) & BM_SDHC_IRQSTAT_CRM) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CRM field to a new value. +#define BW_SDHC_IRQSTAT_CRM(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CRM) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CINT[8] (W1C) + * + * This status bit is set when an interrupt signal is detected from the external + * card. In 1-bit mode, the SDHC will detect the Card Interrupt without the SD + * Clock to support wakeup. In 4-bit mode, the card interrupt signal is sampled + * during the interrupt cycle, so the interrupt from card can only be sampled + * during interrupt cycle, introducing some delay between the interrupt signal from + * the SDIO card and the interrupt to the host system. Writing this bit to 1 can + * clear this bit, but as the interrupt factor from the SDIO card does not clear, + * this bit is set again. To clear this bit, it is required to reset the interrupt + * factor from the external card followed by a writing 1 to this bit. When this + * status has been set, and the host driver needs to service this interrupt, the + * Card Interrupt Signal Enable in the Interrupt Signal Enable register should be + * 0 to stop driving the interrupt signal to the host system. After completion + * of the card interrupt service (it must reset the interrupt factors in the SDIO + * card and the interrupt signal may not be asserted), write 1 to clear this bit, + * set the Card Interrupt Signal Enable to 1, and start sampling the interrupt + * signal again. + * + * Values: + * - 0 - No Card Interrupt. + * - 1 - Generate Card Interrupt. + */ +//@{ +#define BP_SDHC_IRQSTAT_CINT (8U) //!< Bit position for SDHC_IRQSTAT_CINT. +#define BM_SDHC_IRQSTAT_CINT (0x00000100U) //!< Bit mask for SDHC_IRQSTAT_CINT. +#define BS_SDHC_IRQSTAT_CINT (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CINT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CINT field. +#define BR_SDHC_IRQSTAT_CINT (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINT)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CINT. +#define BF_SDHC_IRQSTAT_CINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CINT), uint32_t) & BM_SDHC_IRQSTAT_CINT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINT field to a new value. +#define BW_SDHC_IRQSTAT_CINT(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINT) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CTOE[16] (W1C) + * + * Occurs only if no response is returned within 64 SDCLK cycles from the end + * bit of the command. If the SDHC detects a CMD line conflict, in which case a + * Command CRC Error shall also be set, this bit shall be set without waiting for 64 + * SDCLK cycles. This is because the command will be aborted by the SDHC. + * + * Values: + * - 0 - No error. + * - 1 - Time out. + */ +//@{ +#define BP_SDHC_IRQSTAT_CTOE (16U) //!< Bit position for SDHC_IRQSTAT_CTOE. +#define BM_SDHC_IRQSTAT_CTOE (0x00010000U) //!< Bit mask for SDHC_IRQSTAT_CTOE. +#define BS_SDHC_IRQSTAT_CTOE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CTOE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CTOE field. +#define BR_SDHC_IRQSTAT_CTOE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CTOE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CTOE. +#define BF_SDHC_IRQSTAT_CTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CTOE), uint32_t) & BM_SDHC_IRQSTAT_CTOE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CTOE field to a new value. +#define BW_SDHC_IRQSTAT_CTOE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CTOE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CCE[17] (W1C) + * + * Command CRC Error is generated in two cases. If a response is returned and + * the Command Timeout Error is set to 0, indicating no time-out, this bit is set + * when detecting a CRC error in the command response. The SDHC detects a CMD line + * conflict by monitoring the CMD line when a command is issued. If the SDHC + * drives the CMD line to 1, but detects 0 on the CMD line at the next SDCLK edge, + * then the SDHC shall abort the command (Stop driving CMD line) and set this bit + * to 1. The Command Timeout Error shall also be set to 1 to distinguish CMD line + * conflict. + * + * Values: + * - 0 - No error. + * - 1 - CRC Error generated. + */ +//@{ +#define BP_SDHC_IRQSTAT_CCE (17U) //!< Bit position for SDHC_IRQSTAT_CCE. +#define BM_SDHC_IRQSTAT_CCE (0x00020000U) //!< Bit mask for SDHC_IRQSTAT_CCE. +#define BS_SDHC_IRQSTAT_CCE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CCE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CCE field. +#define BR_SDHC_IRQSTAT_CCE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CCE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CCE. +#define BF_SDHC_IRQSTAT_CCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CCE), uint32_t) & BM_SDHC_IRQSTAT_CCE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCE field to a new value. +#define BW_SDHC_IRQSTAT_CCE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CCE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CEBE[18] (W1C) + * + * Occurs when detecting that the end bit of a command response is 0. + * + * Values: + * - 0 - No error. + * - 1 - End Bit Error generated. + */ +//@{ +#define BP_SDHC_IRQSTAT_CEBE (18U) //!< Bit position for SDHC_IRQSTAT_CEBE. +#define BM_SDHC_IRQSTAT_CEBE (0x00040000U) //!< Bit mask for SDHC_IRQSTAT_CEBE. +#define BS_SDHC_IRQSTAT_CEBE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CEBE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CEBE field. +#define BR_SDHC_IRQSTAT_CEBE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CEBE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CEBE. +#define BF_SDHC_IRQSTAT_CEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CEBE), uint32_t) & BM_SDHC_IRQSTAT_CEBE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CEBE field to a new value. +#define BW_SDHC_IRQSTAT_CEBE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CEBE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field CIE[19] (W1C) + * + * Occurs if a Command Index error occurs in the command response. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_IRQSTAT_CIE (19U) //!< Bit position for SDHC_IRQSTAT_CIE. +#define BM_SDHC_IRQSTAT_CIE (0x00080000U) //!< Bit mask for SDHC_IRQSTAT_CIE. +#define BS_SDHC_IRQSTAT_CIE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CIE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_CIE field. +#define BR_SDHC_IRQSTAT_CIE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CIE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_CIE. +#define BF_SDHC_IRQSTAT_CIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CIE), uint32_t) & BM_SDHC_IRQSTAT_CIE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CIE field to a new value. +#define BW_SDHC_IRQSTAT_CIE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CIE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field DTOE[20] (W1C) + * + * Occurs when detecting one of following time-out conditions. Busy time-out for + * R1b,R5b type Busy time-out after Write CRC status Read Data time-out + * + * Values: + * - 0 - No error. + * - 1 - Time out. + */ +//@{ +#define BP_SDHC_IRQSTAT_DTOE (20U) //!< Bit position for SDHC_IRQSTAT_DTOE. +#define BM_SDHC_IRQSTAT_DTOE (0x00100000U) //!< Bit mask for SDHC_IRQSTAT_DTOE. +#define BS_SDHC_IRQSTAT_DTOE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DTOE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_DTOE field. +#define BR_SDHC_IRQSTAT_DTOE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DTOE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_DTOE. +#define BF_SDHC_IRQSTAT_DTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DTOE), uint32_t) & BM_SDHC_IRQSTAT_DTOE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOE field to a new value. +#define BW_SDHC_IRQSTAT_DTOE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DTOE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field DCE[21] (W1C) + * + * Occurs when detecting a CRC error when transferring read data, which uses the + * DAT line, or when detecting the Write CRC status having a value other than + * 010. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_IRQSTAT_DCE (21U) //!< Bit position for SDHC_IRQSTAT_DCE. +#define BM_SDHC_IRQSTAT_DCE (0x00200000U) //!< Bit mask for SDHC_IRQSTAT_DCE. +#define BS_SDHC_IRQSTAT_DCE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DCE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_DCE field. +#define BR_SDHC_IRQSTAT_DCE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DCE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_DCE. +#define BF_SDHC_IRQSTAT_DCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DCE), uint32_t) & BM_SDHC_IRQSTAT_DCE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DCE field to a new value. +#define BW_SDHC_IRQSTAT_DCE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DCE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field DEBE[22] (W1C) + * + * Occurs either when detecting 0 at the end bit position of read data, which + * uses the DAT line, or at the end bit position of the CRC. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_IRQSTAT_DEBE (22U) //!< Bit position for SDHC_IRQSTAT_DEBE. +#define BM_SDHC_IRQSTAT_DEBE (0x00400000U) //!< Bit mask for SDHC_IRQSTAT_DEBE. +#define BS_SDHC_IRQSTAT_DEBE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DEBE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_DEBE field. +#define BR_SDHC_IRQSTAT_DEBE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DEBE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_DEBE. +#define BF_SDHC_IRQSTAT_DEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DEBE), uint32_t) & BM_SDHC_IRQSTAT_DEBE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DEBE field to a new value. +#define BW_SDHC_IRQSTAT_DEBE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DEBE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field AC12E[24] (W1C) + * + * Occurs when detecting that one of the bits in the Auto CMD12 Error Status + * register has changed from 0 to 1. This bit is set to 1, not only when the errors + * in Auto CMD12 occur, but also when the Auto CMD12 is not executed due to the + * previous command error. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_IRQSTAT_AC12E (24U) //!< Bit position for SDHC_IRQSTAT_AC12E. +#define BM_SDHC_IRQSTAT_AC12E (0x01000000U) //!< Bit mask for SDHC_IRQSTAT_AC12E. +#define BS_SDHC_IRQSTAT_AC12E (1U) //!< Bit field size in bits for SDHC_IRQSTAT_AC12E. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_AC12E field. +#define BR_SDHC_IRQSTAT_AC12E (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_AC12E)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_AC12E. +#define BF_SDHC_IRQSTAT_AC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_AC12E), uint32_t) & BM_SDHC_IRQSTAT_AC12E) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12E field to a new value. +#define BW_SDHC_IRQSTAT_AC12E(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_AC12E) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTAT, field DMAE[28] (W1C) + * + * Occurs when an Internal DMA transfer has failed. This bit is set to 1, when + * some error occurs in the data transfer. This error can be caused by either + * Simple DMA or ADMA, depending on which DMA is in use. The value in DMA System + * Address register is the next fetch address where the error occurs. Because any + * error corrupts the whole data block, the host driver shall restart the transfer + * from the corrupted block boundary. The address of the block boundary can be + * calculated either from the current DSADDR value or from the remaining number of + * blocks and the block size. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_IRQSTAT_DMAE (28U) //!< Bit position for SDHC_IRQSTAT_DMAE. +#define BM_SDHC_IRQSTAT_DMAE (0x10000000U) //!< Bit mask for SDHC_IRQSTAT_DMAE. +#define BS_SDHC_IRQSTAT_DMAE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DMAE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTAT_DMAE field. +#define BR_SDHC_IRQSTAT_DMAE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DMAE)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTAT_DMAE. +#define BF_SDHC_IRQSTAT_DMAE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DMAE), uint32_t) & BM_SDHC_IRQSTAT_DMAE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAE field to a new value. +#define BW_SDHC_IRQSTAT_DMAE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DMAE) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_IRQSTATEN - Interrupt Status Enable register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_IRQSTATEN - Interrupt Status Enable register (RW) + * + * Reset value: 0x117F013FU + * + * Setting the bits in this register to 1 enables the corresponding interrupt + * status to be set by the specified event. If any bit is cleared, the + * corresponding interrupt status bit is also cleared, that is, when the bit in this register + * is cleared, the corresponding bit in interrupt status register is always 0. + * Depending on PROCTL[IABG] bit setting, SDHC may be programmed to sample the + * card interrupt signal during the interrupt period and hold its value in the + * flip-flop. There will be some delays on the card interrupt, asserted from the card, + * to the time the host system is informed. To detect a CMD line conflict, the + * host driver must set both IRQSTATEN[CTOESEN] and IRQSTATEN[CCESEN] to 1. + */ +typedef union _hw_sdhc_irqstaten +{ + uint32_t U; + struct _hw_sdhc_irqstaten_bitfields + { + uint32_t CCSEN : 1; //!< [0] Command Complete Status Enable + uint32_t TCSEN : 1; //!< [1] Transfer Complete Status Enable + uint32_t BGESEN : 1; //!< [2] Block Gap Event Status Enable + uint32_t DINTSEN : 1; //!< [3] DMA Interrupt Status Enable + uint32_t BWRSEN : 1; //!< [4] Buffer Write Ready Status Enable + uint32_t BRRSEN : 1; //!< [5] Buffer Read Ready Status Enable + uint32_t CINSEN : 1; //!< [6] Card Insertion Status Enable + uint32_t CRMSEN : 1; //!< [7] Card Removal Status Enable + uint32_t CINTSEN : 1; //!< [8] Card Interrupt Status Enable + uint32_t RESERVED0 : 7; //!< [15:9] + uint32_t CTOESEN : 1; //!< [16] Command Timeout Error Status Enable + uint32_t CCESEN : 1; //!< [17] Command CRC Error Status Enable + uint32_t CEBESEN : 1; //!< [18] Command End Bit Error Status Enable + uint32_t CIESEN : 1; //!< [19] Command Index Error Status Enable + uint32_t DTOESEN : 1; //!< [20] Data Timeout Error Status Enable + uint32_t DCESEN : 1; //!< [21] Data CRC Error Status Enable + uint32_t DEBESEN : 1; //!< [22] Data End Bit Error Status Enable + uint32_t RESERVED1 : 1; //!< [23] + uint32_t AC12ESEN : 1; //!< [24] Auto CMD12 Error Status Enable + uint32_t RESERVED2 : 3; //!< [27:25] + uint32_t DMAESEN : 1; //!< [28] DMA Error Status Enable + uint32_t RESERVED3 : 3; //!< [31:29] + } B; +} hw_sdhc_irqstaten_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_IRQSTATEN register + */ +//@{ +#define HW_SDHC_IRQSTATEN_ADDR (REGS_SDHC_BASE + 0x34U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_IRQSTATEN (*(__IO hw_sdhc_irqstaten_t *) HW_SDHC_IRQSTATEN_ADDR) +#define HW_SDHC_IRQSTATEN_RD() (HW_SDHC_IRQSTATEN.U) +#define HW_SDHC_IRQSTATEN_WR(v) (HW_SDHC_IRQSTATEN.U = (v)) +#define HW_SDHC_IRQSTATEN_SET(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() | (v))) +#define HW_SDHC_IRQSTATEN_CLR(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() & ~(v))) +#define HW_SDHC_IRQSTATEN_TOG(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_IRQSTATEN bitfields + */ + +/*! + * @name Register SDHC_IRQSTATEN, field CCSEN[0] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CCSEN (0U) //!< Bit position for SDHC_IRQSTATEN_CCSEN. +#define BM_SDHC_IRQSTATEN_CCSEN (0x00000001U) //!< Bit mask for SDHC_IRQSTATEN_CCSEN. +#define BS_SDHC_IRQSTATEN_CCSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CCSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CCSEN field. +#define BR_SDHC_IRQSTATEN_CCSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CCSEN. +#define BF_SDHC_IRQSTATEN_CCSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CCSEN), uint32_t) & BM_SDHC_IRQSTATEN_CCSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCSEN field to a new value. +#define BW_SDHC_IRQSTATEN_CCSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field TCSEN[1] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_TCSEN (1U) //!< Bit position for SDHC_IRQSTATEN_TCSEN. +#define BM_SDHC_IRQSTATEN_TCSEN (0x00000002U) //!< Bit mask for SDHC_IRQSTATEN_TCSEN. +#define BS_SDHC_IRQSTATEN_TCSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_TCSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_TCSEN field. +#define BR_SDHC_IRQSTATEN_TCSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_TCSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_TCSEN. +#define BF_SDHC_IRQSTATEN_TCSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_TCSEN), uint32_t) & BM_SDHC_IRQSTATEN_TCSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the TCSEN field to a new value. +#define BW_SDHC_IRQSTATEN_TCSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_TCSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field BGESEN[2] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_BGESEN (2U) //!< Bit position for SDHC_IRQSTATEN_BGESEN. +#define BM_SDHC_IRQSTATEN_BGESEN (0x00000004U) //!< Bit mask for SDHC_IRQSTATEN_BGESEN. +#define BS_SDHC_IRQSTATEN_BGESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BGESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_BGESEN field. +#define BR_SDHC_IRQSTATEN_BGESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BGESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_BGESEN. +#define BF_SDHC_IRQSTATEN_BGESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BGESEN), uint32_t) & BM_SDHC_IRQSTATEN_BGESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BGESEN field to a new value. +#define BW_SDHC_IRQSTATEN_BGESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BGESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field DINTSEN[3] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_DINTSEN (3U) //!< Bit position for SDHC_IRQSTATEN_DINTSEN. +#define BM_SDHC_IRQSTATEN_DINTSEN (0x00000008U) //!< Bit mask for SDHC_IRQSTATEN_DINTSEN. +#define BS_SDHC_IRQSTATEN_DINTSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DINTSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_DINTSEN field. +#define BR_SDHC_IRQSTATEN_DINTSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DINTSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_DINTSEN. +#define BF_SDHC_IRQSTATEN_DINTSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DINTSEN), uint32_t) & BM_SDHC_IRQSTATEN_DINTSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DINTSEN field to a new value. +#define BW_SDHC_IRQSTATEN_DINTSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DINTSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field BWRSEN[4] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_BWRSEN (4U) //!< Bit position for SDHC_IRQSTATEN_BWRSEN. +#define BM_SDHC_IRQSTATEN_BWRSEN (0x00000010U) //!< Bit mask for SDHC_IRQSTATEN_BWRSEN. +#define BS_SDHC_IRQSTATEN_BWRSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BWRSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_BWRSEN field. +#define BR_SDHC_IRQSTATEN_BWRSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BWRSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_BWRSEN. +#define BF_SDHC_IRQSTATEN_BWRSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BWRSEN), uint32_t) & BM_SDHC_IRQSTATEN_BWRSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BWRSEN field to a new value. +#define BW_SDHC_IRQSTATEN_BWRSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BWRSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field BRRSEN[5] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_BRRSEN (5U) //!< Bit position for SDHC_IRQSTATEN_BRRSEN. +#define BM_SDHC_IRQSTATEN_BRRSEN (0x00000020U) //!< Bit mask for SDHC_IRQSTATEN_BRRSEN. +#define BS_SDHC_IRQSTATEN_BRRSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BRRSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_BRRSEN field. +#define BR_SDHC_IRQSTATEN_BRRSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BRRSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_BRRSEN. +#define BF_SDHC_IRQSTATEN_BRRSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BRRSEN), uint32_t) & BM_SDHC_IRQSTATEN_BRRSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BRRSEN field to a new value. +#define BW_SDHC_IRQSTATEN_BRRSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BRRSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CINSEN[6] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CINSEN (6U) //!< Bit position for SDHC_IRQSTATEN_CINSEN. +#define BM_SDHC_IRQSTATEN_CINSEN (0x00000040U) //!< Bit mask for SDHC_IRQSTATEN_CINSEN. +#define BS_SDHC_IRQSTATEN_CINSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CINSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CINSEN field. +#define BR_SDHC_IRQSTATEN_CINSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CINSEN. +#define BF_SDHC_IRQSTATEN_CINSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CINSEN), uint32_t) & BM_SDHC_IRQSTATEN_CINSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINSEN field to a new value. +#define BW_SDHC_IRQSTATEN_CINSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CRMSEN[7] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CRMSEN (7U) //!< Bit position for SDHC_IRQSTATEN_CRMSEN. +#define BM_SDHC_IRQSTATEN_CRMSEN (0x00000080U) //!< Bit mask for SDHC_IRQSTATEN_CRMSEN. +#define BS_SDHC_IRQSTATEN_CRMSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CRMSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CRMSEN field. +#define BR_SDHC_IRQSTATEN_CRMSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CRMSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CRMSEN. +#define BF_SDHC_IRQSTATEN_CRMSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CRMSEN), uint32_t) & BM_SDHC_IRQSTATEN_CRMSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CRMSEN field to a new value. +#define BW_SDHC_IRQSTATEN_CRMSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CRMSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CINTSEN[8] (RW) + * + * If this bit is set to 0, the SDHC will clear the interrupt request to the + * system. The card interrupt detection is stopped when this bit is cleared and + * restarted when this bit is set to 1. The host driver must clear the this bit + * before servicing the card interrupt and must set this bit again after all interrupt + * requests from the card are cleared to prevent inadvertent interrupts. + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CINTSEN (8U) //!< Bit position for SDHC_IRQSTATEN_CINTSEN. +#define BM_SDHC_IRQSTATEN_CINTSEN (0x00000100U) //!< Bit mask for SDHC_IRQSTATEN_CINTSEN. +#define BS_SDHC_IRQSTATEN_CINTSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CINTSEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CINTSEN field. +#define BR_SDHC_IRQSTATEN_CINTSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINTSEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CINTSEN. +#define BF_SDHC_IRQSTATEN_CINTSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CINTSEN), uint32_t) & BM_SDHC_IRQSTATEN_CINTSEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINTSEN field to a new value. +#define BW_SDHC_IRQSTATEN_CINTSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINTSEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CTOESEN[16] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CTOESEN (16U) //!< Bit position for SDHC_IRQSTATEN_CTOESEN. +#define BM_SDHC_IRQSTATEN_CTOESEN (0x00010000U) //!< Bit mask for SDHC_IRQSTATEN_CTOESEN. +#define BS_SDHC_IRQSTATEN_CTOESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CTOESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CTOESEN field. +#define BR_SDHC_IRQSTATEN_CTOESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CTOESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CTOESEN. +#define BF_SDHC_IRQSTATEN_CTOESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CTOESEN), uint32_t) & BM_SDHC_IRQSTATEN_CTOESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CTOESEN field to a new value. +#define BW_SDHC_IRQSTATEN_CTOESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CTOESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CCESEN[17] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CCESEN (17U) //!< Bit position for SDHC_IRQSTATEN_CCESEN. +#define BM_SDHC_IRQSTATEN_CCESEN (0x00020000U) //!< Bit mask for SDHC_IRQSTATEN_CCESEN. +#define BS_SDHC_IRQSTATEN_CCESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CCESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CCESEN field. +#define BR_SDHC_IRQSTATEN_CCESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CCESEN. +#define BF_SDHC_IRQSTATEN_CCESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CCESEN), uint32_t) & BM_SDHC_IRQSTATEN_CCESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCESEN field to a new value. +#define BW_SDHC_IRQSTATEN_CCESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CEBESEN[18] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CEBESEN (18U) //!< Bit position for SDHC_IRQSTATEN_CEBESEN. +#define BM_SDHC_IRQSTATEN_CEBESEN (0x00040000U) //!< Bit mask for SDHC_IRQSTATEN_CEBESEN. +#define BS_SDHC_IRQSTATEN_CEBESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CEBESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CEBESEN field. +#define BR_SDHC_IRQSTATEN_CEBESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CEBESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CEBESEN. +#define BF_SDHC_IRQSTATEN_CEBESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CEBESEN), uint32_t) & BM_SDHC_IRQSTATEN_CEBESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CEBESEN field to a new value. +#define BW_SDHC_IRQSTATEN_CEBESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CEBESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field CIESEN[19] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_CIESEN (19U) //!< Bit position for SDHC_IRQSTATEN_CIESEN. +#define BM_SDHC_IRQSTATEN_CIESEN (0x00080000U) //!< Bit mask for SDHC_IRQSTATEN_CIESEN. +#define BS_SDHC_IRQSTATEN_CIESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CIESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_CIESEN field. +#define BR_SDHC_IRQSTATEN_CIESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CIESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_CIESEN. +#define BF_SDHC_IRQSTATEN_CIESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CIESEN), uint32_t) & BM_SDHC_IRQSTATEN_CIESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CIESEN field to a new value. +#define BW_SDHC_IRQSTATEN_CIESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CIESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field DTOESEN[20] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_DTOESEN (20U) //!< Bit position for SDHC_IRQSTATEN_DTOESEN. +#define BM_SDHC_IRQSTATEN_DTOESEN (0x00100000U) //!< Bit mask for SDHC_IRQSTATEN_DTOESEN. +#define BS_SDHC_IRQSTATEN_DTOESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DTOESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_DTOESEN field. +#define BR_SDHC_IRQSTATEN_DTOESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DTOESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_DTOESEN. +#define BF_SDHC_IRQSTATEN_DTOESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DTOESEN), uint32_t) & BM_SDHC_IRQSTATEN_DTOESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOESEN field to a new value. +#define BW_SDHC_IRQSTATEN_DTOESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DTOESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field DCESEN[21] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_DCESEN (21U) //!< Bit position for SDHC_IRQSTATEN_DCESEN. +#define BM_SDHC_IRQSTATEN_DCESEN (0x00200000U) //!< Bit mask for SDHC_IRQSTATEN_DCESEN. +#define BS_SDHC_IRQSTATEN_DCESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DCESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_DCESEN field. +#define BR_SDHC_IRQSTATEN_DCESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DCESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_DCESEN. +#define BF_SDHC_IRQSTATEN_DCESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DCESEN), uint32_t) & BM_SDHC_IRQSTATEN_DCESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DCESEN field to a new value. +#define BW_SDHC_IRQSTATEN_DCESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DCESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field DEBESEN[22] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_DEBESEN (22U) //!< Bit position for SDHC_IRQSTATEN_DEBESEN. +#define BM_SDHC_IRQSTATEN_DEBESEN (0x00400000U) //!< Bit mask for SDHC_IRQSTATEN_DEBESEN. +#define BS_SDHC_IRQSTATEN_DEBESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DEBESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_DEBESEN field. +#define BR_SDHC_IRQSTATEN_DEBESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DEBESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_DEBESEN. +#define BF_SDHC_IRQSTATEN_DEBESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DEBESEN), uint32_t) & BM_SDHC_IRQSTATEN_DEBESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DEBESEN field to a new value. +#define BW_SDHC_IRQSTATEN_DEBESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DEBESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field AC12ESEN[24] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_AC12ESEN (24U) //!< Bit position for SDHC_IRQSTATEN_AC12ESEN. +#define BM_SDHC_IRQSTATEN_AC12ESEN (0x01000000U) //!< Bit mask for SDHC_IRQSTATEN_AC12ESEN. +#define BS_SDHC_IRQSTATEN_AC12ESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_AC12ESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_AC12ESEN field. +#define BR_SDHC_IRQSTATEN_AC12ESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_AC12ESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_AC12ESEN. +#define BF_SDHC_IRQSTATEN_AC12ESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_AC12ESEN), uint32_t) & BM_SDHC_IRQSTATEN_AC12ESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12ESEN field to a new value. +#define BW_SDHC_IRQSTATEN_AC12ESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_AC12ESEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSTATEN, field DMAESEN[28] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSTATEN_DMAESEN (28U) //!< Bit position for SDHC_IRQSTATEN_DMAESEN. +#define BM_SDHC_IRQSTATEN_DMAESEN (0x10000000U) //!< Bit mask for SDHC_IRQSTATEN_DMAESEN. +#define BS_SDHC_IRQSTATEN_DMAESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DMAESEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSTATEN_DMAESEN field. +#define BR_SDHC_IRQSTATEN_DMAESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DMAESEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSTATEN_DMAESEN. +#define BF_SDHC_IRQSTATEN_DMAESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DMAESEN), uint32_t) & BM_SDHC_IRQSTATEN_DMAESEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAESEN field to a new value. +#define BW_SDHC_IRQSTATEN_DMAESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DMAESEN) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_IRQSIGEN - Interrupt Signal Enable register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_IRQSIGEN - Interrupt Signal Enable register (RW) + * + * Reset value: 0x00000000U + * + * This register is used to select which interrupt status is indicated to the + * host system as the interrupt. All of these status bits share the same interrupt + * line. Setting any of these bits to 1 enables interrupt generation. The + * corresponding status register bit will generate an interrupt when the corresponding + * interrupt signal enable bit is set. + */ +typedef union _hw_sdhc_irqsigen +{ + uint32_t U; + struct _hw_sdhc_irqsigen_bitfields + { + uint32_t CCIEN : 1; //!< [0] Command Complete Interrupt Enable + uint32_t TCIEN : 1; //!< [1] Transfer Complete Interrupt Enable + uint32_t BGEIEN : 1; //!< [2] Block Gap Event Interrupt Enable + uint32_t DINTIEN : 1; //!< [3] DMA Interrupt Enable + uint32_t BWRIEN : 1; //!< [4] Buffer Write Ready Interrupt Enable + uint32_t BRRIEN : 1; //!< [5] Buffer Read Ready Interrupt Enable + uint32_t CINSIEN : 1; //!< [6] Card Insertion Interrupt Enable + uint32_t CRMIEN : 1; //!< [7] Card Removal Interrupt Enable + uint32_t CINTIEN : 1; //!< [8] Card Interrupt Enable + uint32_t RESERVED0 : 7; //!< [15:9] + uint32_t CTOEIEN : 1; //!< [16] Command Timeout Error Interrupt Enable + uint32_t CCEIEN : 1; //!< [17] Command CRC Error Interrupt Enable + uint32_t CEBEIEN : 1; //!< [18] Command End Bit Error Interrupt Enable + uint32_t CIEIEN : 1; //!< [19] Command Index Error Interrupt Enable + uint32_t DTOEIEN : 1; //!< [20] Data Timeout Error Interrupt Enable + uint32_t DCEIEN : 1; //!< [21] Data CRC Error Interrupt Enable + uint32_t DEBEIEN : 1; //!< [22] Data End Bit Error Interrupt Enable + uint32_t RESERVED1 : 1; //!< [23] + uint32_t AC12EIEN : 1; //!< [24] Auto CMD12 Error Interrupt Enable + uint32_t RESERVED2 : 3; //!< [27:25] + uint32_t DMAEIEN : 1; //!< [28] DMA Error Interrupt Enable + uint32_t RESERVED3 : 3; //!< [31:29] + } B; +} hw_sdhc_irqsigen_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_IRQSIGEN register + */ +//@{ +#define HW_SDHC_IRQSIGEN_ADDR (REGS_SDHC_BASE + 0x38U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_IRQSIGEN (*(__IO hw_sdhc_irqsigen_t *) HW_SDHC_IRQSIGEN_ADDR) +#define HW_SDHC_IRQSIGEN_RD() (HW_SDHC_IRQSIGEN.U) +#define HW_SDHC_IRQSIGEN_WR(v) (HW_SDHC_IRQSIGEN.U = (v)) +#define HW_SDHC_IRQSIGEN_SET(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() | (v))) +#define HW_SDHC_IRQSIGEN_CLR(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() & ~(v))) +#define HW_SDHC_IRQSIGEN_TOG(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_IRQSIGEN bitfields + */ + +/*! + * @name Register SDHC_IRQSIGEN, field CCIEN[0] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CCIEN (0U) //!< Bit position for SDHC_IRQSIGEN_CCIEN. +#define BM_SDHC_IRQSIGEN_CCIEN (0x00000001U) //!< Bit mask for SDHC_IRQSIGEN_CCIEN. +#define BS_SDHC_IRQSIGEN_CCIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CCIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CCIEN field. +#define BR_SDHC_IRQSIGEN_CCIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CCIEN. +#define BF_SDHC_IRQSIGEN_CCIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CCIEN), uint32_t) & BM_SDHC_IRQSIGEN_CCIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CCIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field TCIEN[1] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_TCIEN (1U) //!< Bit position for SDHC_IRQSIGEN_TCIEN. +#define BM_SDHC_IRQSIGEN_TCIEN (0x00000002U) //!< Bit mask for SDHC_IRQSIGEN_TCIEN. +#define BS_SDHC_IRQSIGEN_TCIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_TCIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_TCIEN field. +#define BR_SDHC_IRQSIGEN_TCIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_TCIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_TCIEN. +#define BF_SDHC_IRQSIGEN_TCIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_TCIEN), uint32_t) & BM_SDHC_IRQSIGEN_TCIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the TCIEN field to a new value. +#define BW_SDHC_IRQSIGEN_TCIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_TCIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field BGEIEN[2] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_BGEIEN (2U) //!< Bit position for SDHC_IRQSIGEN_BGEIEN. +#define BM_SDHC_IRQSIGEN_BGEIEN (0x00000004U) //!< Bit mask for SDHC_IRQSIGEN_BGEIEN. +#define BS_SDHC_IRQSIGEN_BGEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BGEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_BGEIEN field. +#define BR_SDHC_IRQSIGEN_BGEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BGEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_BGEIEN. +#define BF_SDHC_IRQSIGEN_BGEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BGEIEN), uint32_t) & BM_SDHC_IRQSIGEN_BGEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BGEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_BGEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BGEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field DINTIEN[3] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_DINTIEN (3U) //!< Bit position for SDHC_IRQSIGEN_DINTIEN. +#define BM_SDHC_IRQSIGEN_DINTIEN (0x00000008U) //!< Bit mask for SDHC_IRQSIGEN_DINTIEN. +#define BS_SDHC_IRQSIGEN_DINTIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DINTIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_DINTIEN field. +#define BR_SDHC_IRQSIGEN_DINTIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DINTIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_DINTIEN. +#define BF_SDHC_IRQSIGEN_DINTIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DINTIEN), uint32_t) & BM_SDHC_IRQSIGEN_DINTIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DINTIEN field to a new value. +#define BW_SDHC_IRQSIGEN_DINTIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DINTIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field BWRIEN[4] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_BWRIEN (4U) //!< Bit position for SDHC_IRQSIGEN_BWRIEN. +#define BM_SDHC_IRQSIGEN_BWRIEN (0x00000010U) //!< Bit mask for SDHC_IRQSIGEN_BWRIEN. +#define BS_SDHC_IRQSIGEN_BWRIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BWRIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_BWRIEN field. +#define BR_SDHC_IRQSIGEN_BWRIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BWRIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_BWRIEN. +#define BF_SDHC_IRQSIGEN_BWRIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BWRIEN), uint32_t) & BM_SDHC_IRQSIGEN_BWRIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BWRIEN field to a new value. +#define BW_SDHC_IRQSIGEN_BWRIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BWRIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field BRRIEN[5] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_BRRIEN (5U) //!< Bit position for SDHC_IRQSIGEN_BRRIEN. +#define BM_SDHC_IRQSIGEN_BRRIEN (0x00000020U) //!< Bit mask for SDHC_IRQSIGEN_BRRIEN. +#define BS_SDHC_IRQSIGEN_BRRIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BRRIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_BRRIEN field. +#define BR_SDHC_IRQSIGEN_BRRIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BRRIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_BRRIEN. +#define BF_SDHC_IRQSIGEN_BRRIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BRRIEN), uint32_t) & BM_SDHC_IRQSIGEN_BRRIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BRRIEN field to a new value. +#define BW_SDHC_IRQSIGEN_BRRIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BRRIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CINSIEN[6] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CINSIEN (6U) //!< Bit position for SDHC_IRQSIGEN_CINSIEN. +#define BM_SDHC_IRQSIGEN_CINSIEN (0x00000040U) //!< Bit mask for SDHC_IRQSIGEN_CINSIEN. +#define BS_SDHC_IRQSIGEN_CINSIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CINSIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CINSIEN field. +#define BR_SDHC_IRQSIGEN_CINSIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINSIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CINSIEN. +#define BF_SDHC_IRQSIGEN_CINSIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CINSIEN), uint32_t) & BM_SDHC_IRQSIGEN_CINSIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINSIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CINSIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINSIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CRMIEN[7] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CRMIEN (7U) //!< Bit position for SDHC_IRQSIGEN_CRMIEN. +#define BM_SDHC_IRQSIGEN_CRMIEN (0x00000080U) //!< Bit mask for SDHC_IRQSIGEN_CRMIEN. +#define BS_SDHC_IRQSIGEN_CRMIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CRMIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CRMIEN field. +#define BR_SDHC_IRQSIGEN_CRMIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CRMIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CRMIEN. +#define BF_SDHC_IRQSIGEN_CRMIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CRMIEN), uint32_t) & BM_SDHC_IRQSIGEN_CRMIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CRMIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CRMIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CRMIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CINTIEN[8] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CINTIEN (8U) //!< Bit position for SDHC_IRQSIGEN_CINTIEN. +#define BM_SDHC_IRQSIGEN_CINTIEN (0x00000100U) //!< Bit mask for SDHC_IRQSIGEN_CINTIEN. +#define BS_SDHC_IRQSIGEN_CINTIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CINTIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CINTIEN field. +#define BR_SDHC_IRQSIGEN_CINTIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINTIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CINTIEN. +#define BF_SDHC_IRQSIGEN_CINTIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CINTIEN), uint32_t) & BM_SDHC_IRQSIGEN_CINTIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINTIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CINTIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINTIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CTOEIEN[16] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CTOEIEN (16U) //!< Bit position for SDHC_IRQSIGEN_CTOEIEN. +#define BM_SDHC_IRQSIGEN_CTOEIEN (0x00010000U) //!< Bit mask for SDHC_IRQSIGEN_CTOEIEN. +#define BS_SDHC_IRQSIGEN_CTOEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CTOEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CTOEIEN field. +#define BR_SDHC_IRQSIGEN_CTOEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CTOEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CTOEIEN. +#define BF_SDHC_IRQSIGEN_CTOEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CTOEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CTOEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CTOEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CTOEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CTOEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CCEIEN[17] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CCEIEN (17U) //!< Bit position for SDHC_IRQSIGEN_CCEIEN. +#define BM_SDHC_IRQSIGEN_CCEIEN (0x00020000U) //!< Bit mask for SDHC_IRQSIGEN_CCEIEN. +#define BS_SDHC_IRQSIGEN_CCEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CCEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CCEIEN field. +#define BR_SDHC_IRQSIGEN_CCEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CCEIEN. +#define BF_SDHC_IRQSIGEN_CCEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CCEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CCEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CCEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CEBEIEN[18] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CEBEIEN (18U) //!< Bit position for SDHC_IRQSIGEN_CEBEIEN. +#define BM_SDHC_IRQSIGEN_CEBEIEN (0x00040000U) //!< Bit mask for SDHC_IRQSIGEN_CEBEIEN. +#define BS_SDHC_IRQSIGEN_CEBEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CEBEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CEBEIEN field. +#define BR_SDHC_IRQSIGEN_CEBEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CEBEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CEBEIEN. +#define BF_SDHC_IRQSIGEN_CEBEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CEBEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CEBEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CEBEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CEBEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CEBEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field CIEIEN[19] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_CIEIEN (19U) //!< Bit position for SDHC_IRQSIGEN_CIEIEN. +#define BM_SDHC_IRQSIGEN_CIEIEN (0x00080000U) //!< Bit mask for SDHC_IRQSIGEN_CIEIEN. +#define BS_SDHC_IRQSIGEN_CIEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CIEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_CIEIEN field. +#define BR_SDHC_IRQSIGEN_CIEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CIEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_CIEIEN. +#define BF_SDHC_IRQSIGEN_CIEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CIEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CIEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CIEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_CIEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CIEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field DTOEIEN[20] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_DTOEIEN (20U) //!< Bit position for SDHC_IRQSIGEN_DTOEIEN. +#define BM_SDHC_IRQSIGEN_DTOEIEN (0x00100000U) //!< Bit mask for SDHC_IRQSIGEN_DTOEIEN. +#define BS_SDHC_IRQSIGEN_DTOEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DTOEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_DTOEIEN field. +#define BR_SDHC_IRQSIGEN_DTOEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DTOEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_DTOEIEN. +#define BF_SDHC_IRQSIGEN_DTOEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DTOEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DTOEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_DTOEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DTOEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field DCEIEN[21] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_DCEIEN (21U) //!< Bit position for SDHC_IRQSIGEN_DCEIEN. +#define BM_SDHC_IRQSIGEN_DCEIEN (0x00200000U) //!< Bit mask for SDHC_IRQSIGEN_DCEIEN. +#define BS_SDHC_IRQSIGEN_DCEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DCEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_DCEIEN field. +#define BR_SDHC_IRQSIGEN_DCEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DCEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_DCEIEN. +#define BF_SDHC_IRQSIGEN_DCEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DCEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DCEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DCEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_DCEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DCEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field DEBEIEN[22] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_DEBEIEN (22U) //!< Bit position for SDHC_IRQSIGEN_DEBEIEN. +#define BM_SDHC_IRQSIGEN_DEBEIEN (0x00400000U) //!< Bit mask for SDHC_IRQSIGEN_DEBEIEN. +#define BS_SDHC_IRQSIGEN_DEBEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DEBEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_DEBEIEN field. +#define BR_SDHC_IRQSIGEN_DEBEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DEBEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_DEBEIEN. +#define BF_SDHC_IRQSIGEN_DEBEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DEBEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DEBEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DEBEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_DEBEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DEBEIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field AC12EIEN[24] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_AC12EIEN (24U) //!< Bit position for SDHC_IRQSIGEN_AC12EIEN. +#define BM_SDHC_IRQSIGEN_AC12EIEN (0x01000000U) //!< Bit mask for SDHC_IRQSIGEN_AC12EIEN. +#define BS_SDHC_IRQSIGEN_AC12EIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_AC12EIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_AC12EIEN field. +#define BR_SDHC_IRQSIGEN_AC12EIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_AC12EIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_AC12EIEN. +#define BF_SDHC_IRQSIGEN_AC12EIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_AC12EIEN), uint32_t) & BM_SDHC_IRQSIGEN_AC12EIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12EIEN field to a new value. +#define BW_SDHC_IRQSIGEN_AC12EIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_AC12EIEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_IRQSIGEN, field DMAEIEN[28] (RW) + * + * Values: + * - 0 - Masked + * - 1 - Enabled + */ +//@{ +#define BP_SDHC_IRQSIGEN_DMAEIEN (28U) //!< Bit position for SDHC_IRQSIGEN_DMAEIEN. +#define BM_SDHC_IRQSIGEN_DMAEIEN (0x10000000U) //!< Bit mask for SDHC_IRQSIGEN_DMAEIEN. +#define BS_SDHC_IRQSIGEN_DMAEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DMAEIEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_IRQSIGEN_DMAEIEN field. +#define BR_SDHC_IRQSIGEN_DMAEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DMAEIEN)) +#endif + +//! @brief Format value for bitfield SDHC_IRQSIGEN_DMAEIEN. +#define BF_SDHC_IRQSIGEN_DMAEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DMAEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DMAEIEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAEIEN field to a new value. +#define BW_SDHC_IRQSIGEN_DMAEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DMAEIEN) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_AC12ERR - Auto CMD12 Error Status Register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_AC12ERR - Auto CMD12 Error Status Register (RO) + * + * Reset value: 0x00000000U + * + * When the AC12ESEN bit in the Status register is set, the host driver shall + * check this register to identify what kind of error the Auto CMD12 indicated. + * This register is valid only when the Auto CMD12 Error status bit is set. The + * following table shows the relationship between the Auto CMGD12 CRC error and the + * Auto CMD12 command timeout error. Relationship between Command CRC Error and + * Command Timeout Error For Auto CMD12 Auto CMD12 CRC error Auto CMD12 timeout + * error Type of error 0 0 No error 0 1 Response timeout error 1 0 Response CRC + * error 1 1 CMD line conflict Changes in Auto CMD12 Error Status register can be + * classified in three scenarios: When the SDHC is going to issue an Auto CMD12: Set + * bit 0 to 1 if the Auto CMD12 can't be issued due to an error in the previous + * command. Set bit 0 to 0 if the auto CMD12 is issued. At the end bit of an auto + * CMD12 response: Check errors corresponding to bits 1-4. Set bits 1-4 + * corresponding to detected errors. Clear bits 1-4 corresponding to detected errors. + * Before reading the Auto CMD12 error status bit 7: Set bit 7 to 1 if there is a + * command that can't be issued. Clear bit 7 if there is no command to issue. The + * timing for generating the auto CMD12 error and writing to the command register + * are asynchronous. After that, bit 7 shall be sampled when the driver is not + * writing to the command register. So it is suggested to read this register only + * when IRQSTAT[AC12E] is set. An Auto CMD12 error interrupt is generated when one + * of the error bits (0-4) is set to 1. The command not issued by auto CMD12 + * error does not generate an interrupt. + */ +typedef union _hw_sdhc_ac12err +{ + uint32_t U; + struct _hw_sdhc_ac12err_bitfields + { + uint32_t AC12NE : 1; //!< [0] Auto CMD12 Not Executed + uint32_t AC12TOE : 1; //!< [1] Auto CMD12 Timeout Error + uint32_t AC12EBE : 1; //!< [2] Auto CMD12 End Bit Error + uint32_t AC12CE : 1; //!< [3] Auto CMD12 CRC Error + uint32_t AC12IE : 1; //!< [4] Auto CMD12 Index Error + uint32_t RESERVED0 : 2; //!< [6:5] + uint32_t CNIBAC12E : 1; //!< [7] Command Not Issued By Auto CMD12 + //! Error + uint32_t RESERVED1 : 24; //!< [31:8] + } B; +} hw_sdhc_ac12err_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_AC12ERR register + */ +//@{ +#define HW_SDHC_AC12ERR_ADDR (REGS_SDHC_BASE + 0x3CU) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_AC12ERR (*(__I hw_sdhc_ac12err_t *) HW_SDHC_AC12ERR_ADDR) +#define HW_SDHC_AC12ERR_RD() (HW_SDHC_AC12ERR.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_AC12ERR bitfields + */ + +/*! + * @name Register SDHC_AC12ERR, field AC12NE[0] (RO) + * + * If memory multiple block data transfer is not started, due to a command + * error, this bit is not set because it is not necessary to issue an auto CMD12. + * Setting this bit to 1 means the SDHC cannot issue the auto CMD12 to stop a memory + * multiple block data transfer due to some error. If this bit is set to 1, other + * error status bits (1-4) have no meaning. + * + * Values: + * - 0 - Executed. + * - 1 - Not executed. + */ +//@{ +#define BP_SDHC_AC12ERR_AC12NE (0U) //!< Bit position for SDHC_AC12ERR_AC12NE. +#define BM_SDHC_AC12ERR_AC12NE (0x00000001U) //!< Bit mask for SDHC_AC12ERR_AC12NE. +#define BS_SDHC_AC12ERR_AC12NE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12NE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_AC12NE field. +#define BR_SDHC_AC12ERR_AC12NE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12NE)) +#endif +//@} + +/*! + * @name Register SDHC_AC12ERR, field AC12TOE[1] (RO) + * + * Occurs if no response is returned within 64 SDCLK cycles from the end bit of + * the command. If this bit is set to 1, the other error status bits (2-4) have + * no meaning. + * + * Values: + * - 0 - No error. + * - 1 - Time out. + */ +//@{ +#define BP_SDHC_AC12ERR_AC12TOE (1U) //!< Bit position for SDHC_AC12ERR_AC12TOE. +#define BM_SDHC_AC12ERR_AC12TOE (0x00000002U) //!< Bit mask for SDHC_AC12ERR_AC12TOE. +#define BS_SDHC_AC12ERR_AC12TOE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12TOE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_AC12TOE field. +#define BR_SDHC_AC12ERR_AC12TOE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12TOE)) +#endif +//@} + +/*! + * @name Register SDHC_AC12ERR, field AC12EBE[2] (RO) + * + * Occurs when detecting that the end bit of command response is 0 which must be + * 1. + * + * Values: + * - 0 - No error. + * - 1 - End bit error generated. + */ +//@{ +#define BP_SDHC_AC12ERR_AC12EBE (2U) //!< Bit position for SDHC_AC12ERR_AC12EBE. +#define BM_SDHC_AC12ERR_AC12EBE (0x00000004U) //!< Bit mask for SDHC_AC12ERR_AC12EBE. +#define BS_SDHC_AC12ERR_AC12EBE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12EBE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_AC12EBE field. +#define BR_SDHC_AC12ERR_AC12EBE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12EBE)) +#endif +//@} + +/*! + * @name Register SDHC_AC12ERR, field AC12CE[3] (RO) + * + * Occurs when detecting a CRC error in the command response. + * + * Values: + * - 0 - No CRC error. + * - 1 - CRC error met in Auto CMD12 response. + */ +//@{ +#define BP_SDHC_AC12ERR_AC12CE (3U) //!< Bit position for SDHC_AC12ERR_AC12CE. +#define BM_SDHC_AC12ERR_AC12CE (0x00000008U) //!< Bit mask for SDHC_AC12ERR_AC12CE. +#define BS_SDHC_AC12ERR_AC12CE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12CE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_AC12CE field. +#define BR_SDHC_AC12ERR_AC12CE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12CE)) +#endif +//@} + +/*! + * @name Register SDHC_AC12ERR, field AC12IE[4] (RO) + * + * Occurs if the command index error occurs in response to a command. + * + * Values: + * - 0 - No error. + * - 1 - Error, the CMD index in response is not CMD12. + */ +//@{ +#define BP_SDHC_AC12ERR_AC12IE (4U) //!< Bit position for SDHC_AC12ERR_AC12IE. +#define BM_SDHC_AC12ERR_AC12IE (0x00000010U) //!< Bit mask for SDHC_AC12ERR_AC12IE. +#define BS_SDHC_AC12ERR_AC12IE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12IE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_AC12IE field. +#define BR_SDHC_AC12ERR_AC12IE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12IE)) +#endif +//@} + +/*! + * @name Register SDHC_AC12ERR, field CNIBAC12E[7] (RO) + * + * Setting this bit to 1 means CMD_wo_DAT is not executed due to an auto CMD12 + * error (D04-D01) in this register. + * + * Values: + * - 0 - No error. + * - 1 - Not issued. + */ +//@{ +#define BP_SDHC_AC12ERR_CNIBAC12E (7U) //!< Bit position for SDHC_AC12ERR_CNIBAC12E. +#define BM_SDHC_AC12ERR_CNIBAC12E (0x00000080U) //!< Bit mask for SDHC_AC12ERR_CNIBAC12E. +#define BS_SDHC_AC12ERR_CNIBAC12E (1U) //!< Bit field size in bits for SDHC_AC12ERR_CNIBAC12E. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_AC12ERR_CNIBAC12E field. +#define BR_SDHC_AC12ERR_CNIBAC12E (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_CNIBAC12E)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_HTCAPBLT - Host Controller Capabilities +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_HTCAPBLT - Host Controller Capabilities (RO) + * + * Reset value: 0x07F30000U + * + * This register provides the host driver with information specific to the SDHC + * implementation. The value in this register is the power-on-reset value, and + * does not change with a software reset. Any write to this register is ignored. + */ +typedef union _hw_sdhc_htcapblt +{ + uint32_t U; + struct _hw_sdhc_htcapblt_bitfields + { + uint32_t RESERVED0 : 16; //!< [15:0] + uint32_t MBL : 3; //!< [18:16] Max Block Length + uint32_t RESERVED1 : 1; //!< [19] + uint32_t ADMAS : 1; //!< [20] ADMA Support + uint32_t HSS : 1; //!< [21] High Speed Support + uint32_t DMAS : 1; //!< [22] DMA Support + uint32_t SRS : 1; //!< [23] Suspend/Resume Support + uint32_t VS33 : 1; //!< [24] Voltage Support 3.3 V + uint32_t RESERVED2 : 7; //!< [31:25] + } B; +} hw_sdhc_htcapblt_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_HTCAPBLT register + */ +//@{ +#define HW_SDHC_HTCAPBLT_ADDR (REGS_SDHC_BASE + 0x40U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_HTCAPBLT (*(__I hw_sdhc_htcapblt_t *) HW_SDHC_HTCAPBLT_ADDR) +#define HW_SDHC_HTCAPBLT_RD() (HW_SDHC_HTCAPBLT.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_HTCAPBLT bitfields + */ + +/*! + * @name Register SDHC_HTCAPBLT, field MBL[18:16] (RO) + * + * This value indicates the maximum block size that the host driver can read and + * write to the buffer in the SDHC. The buffer shall transfer block size without + * wait cycles. + * + * Values: + * - 000 - 512 bytes + * - 001 - 1024 bytes + * - 010 - 2048 bytes + * - 011 - 4096 bytes + */ +//@{ +#define BP_SDHC_HTCAPBLT_MBL (16U) //!< Bit position for SDHC_HTCAPBLT_MBL. +#define BM_SDHC_HTCAPBLT_MBL (0x00070000U) //!< Bit mask for SDHC_HTCAPBLT_MBL. +#define BS_SDHC_HTCAPBLT_MBL (3U) //!< Bit field size in bits for SDHC_HTCAPBLT_MBL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_MBL field. +#define BR_SDHC_HTCAPBLT_MBL (HW_SDHC_HTCAPBLT.B.MBL) +#endif +//@} + +/*! + * @name Register SDHC_HTCAPBLT, field ADMAS[20] (RO) + * + * This bit indicates whether the SDHC supports the ADMA feature. + * + * Values: + * - 0 - Advanced DMA not supported. + * - 1 - Advanced DMA supported. + */ +//@{ +#define BP_SDHC_HTCAPBLT_ADMAS (20U) //!< Bit position for SDHC_HTCAPBLT_ADMAS. +#define BM_SDHC_HTCAPBLT_ADMAS (0x00100000U) //!< Bit mask for SDHC_HTCAPBLT_ADMAS. +#define BS_SDHC_HTCAPBLT_ADMAS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_ADMAS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_ADMAS field. +#define BR_SDHC_HTCAPBLT_ADMAS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_ADMAS)) +#endif +//@} + +/*! + * @name Register SDHC_HTCAPBLT, field HSS[21] (RO) + * + * This bit indicates whether the SDHC supports high speed mode and the host + * system can supply a SD Clock frequency from 25 MHz to 50 MHz. + * + * Values: + * - 0 - High speed not supported. + * - 1 - High speed supported. + */ +//@{ +#define BP_SDHC_HTCAPBLT_HSS (21U) //!< Bit position for SDHC_HTCAPBLT_HSS. +#define BM_SDHC_HTCAPBLT_HSS (0x00200000U) //!< Bit mask for SDHC_HTCAPBLT_HSS. +#define BS_SDHC_HTCAPBLT_HSS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_HSS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_HSS field. +#define BR_SDHC_HTCAPBLT_HSS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_HSS)) +#endif +//@} + +/*! + * @name Register SDHC_HTCAPBLT, field DMAS[22] (RO) + * + * This bit indicates whether the SDHC is capable of using the internal DMA to + * transfer data between system memory and the data buffer directly. + * + * Values: + * - 0 - DMA not supported. + * - 1 - DMA supported. + */ +//@{ +#define BP_SDHC_HTCAPBLT_DMAS (22U) //!< Bit position for SDHC_HTCAPBLT_DMAS. +#define BM_SDHC_HTCAPBLT_DMAS (0x00400000U) //!< Bit mask for SDHC_HTCAPBLT_DMAS. +#define BS_SDHC_HTCAPBLT_DMAS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_DMAS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_DMAS field. +#define BR_SDHC_HTCAPBLT_DMAS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_DMAS)) +#endif +//@} + +/*! + * @name Register SDHC_HTCAPBLT, field SRS[23] (RO) + * + * This bit indicates whether the SDHC supports suspend / resume functionality. + * If this bit is 0, the suspend and resume mechanism, as well as the read Wwait, + * are not supported, and the host driver shall not issue either suspend or + * resume commands. + * + * Values: + * - 0 - Not supported. + * - 1 - Supported. + */ +//@{ +#define BP_SDHC_HTCAPBLT_SRS (23U) //!< Bit position for SDHC_HTCAPBLT_SRS. +#define BM_SDHC_HTCAPBLT_SRS (0x00800000U) //!< Bit mask for SDHC_HTCAPBLT_SRS. +#define BS_SDHC_HTCAPBLT_SRS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_SRS. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_SRS field. +#define BR_SDHC_HTCAPBLT_SRS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_SRS)) +#endif +//@} + +/*! + * @name Register SDHC_HTCAPBLT, field VS33[24] (RO) + * + * This bit shall depend on the host system ability. + * + * Values: + * - 0 - 3.3 V not supported. + * - 1 - 3.3 V supported. + */ +//@{ +#define BP_SDHC_HTCAPBLT_VS33 (24U) //!< Bit position for SDHC_HTCAPBLT_VS33. +#define BM_SDHC_HTCAPBLT_VS33 (0x01000000U) //!< Bit mask for SDHC_HTCAPBLT_VS33. +#define BS_SDHC_HTCAPBLT_VS33 (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_VS33. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HTCAPBLT_VS33 field. +#define BR_SDHC_HTCAPBLT_VS33 (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_VS33)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_WML - Watermark Level Register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_WML - Watermark Level Register (RW) + * + * Reset value: 0x00100010U + * + * Both write and read watermark levels (FIFO threshold) are configurable. There + * value can range from 1 to 128 words. Both write and read burst lengths are + * also configurable. There value can range from 1 to 31 words. + */ +typedef union _hw_sdhc_wml +{ + uint32_t U; + struct _hw_sdhc_wml_bitfields + { + uint32_t RDWML : 8; //!< [7:0] Read Watermark Level + uint32_t RESERVED0 : 8; //!< [15:8] + uint32_t WRWML : 8; //!< [23:16] Write Watermark Level + uint32_t RESERVED1 : 8; //!< [31:24] + } B; +} hw_sdhc_wml_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_WML register + */ +//@{ +#define HW_SDHC_WML_ADDR (REGS_SDHC_BASE + 0x44U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_WML (*(__IO hw_sdhc_wml_t *) HW_SDHC_WML_ADDR) +#define HW_SDHC_WML_RD() (HW_SDHC_WML.U) +#define HW_SDHC_WML_WR(v) (HW_SDHC_WML.U = (v)) +#define HW_SDHC_WML_SET(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() | (v))) +#define HW_SDHC_WML_CLR(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() & ~(v))) +#define HW_SDHC_WML_TOG(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_WML bitfields + */ + +/*! + * @name Register SDHC_WML, field RDWML[7:0] (RW) + * + * The number of words used as the watermark level (FIFO threshold) in a DMA + * read operation. Also the number of words as a sequence of read bursts in + * back-to-back mode. The maximum legal value for the read water mark level is 128. + */ +//@{ +#define BP_SDHC_WML_RDWML (0U) //!< Bit position for SDHC_WML_RDWML. +#define BM_SDHC_WML_RDWML (0x000000FFU) //!< Bit mask for SDHC_WML_RDWML. +#define BS_SDHC_WML_RDWML (8U) //!< Bit field size in bits for SDHC_WML_RDWML. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_WML_RDWML field. +#define BR_SDHC_WML_RDWML (HW_SDHC_WML.B.RDWML) +#endif + +//! @brief Format value for bitfield SDHC_WML_RDWML. +#define BF_SDHC_WML_RDWML(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_WML_RDWML), uint32_t) & BM_SDHC_WML_RDWML) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the RDWML field to a new value. +#define BW_SDHC_WML_RDWML(v) (HW_SDHC_WML_WR((HW_SDHC_WML_RD() & ~BM_SDHC_WML_RDWML) | BF_SDHC_WML_RDWML(v))) +#endif +//@} + +/*! + * @name Register SDHC_WML, field WRWML[23:16] (RW) + * + * The number of words used as the watermark level (FIFO threshold) in a DMA + * write operation. Also the number of words as a sequence of write bursts in + * back-to-back mode. The maximum legal value for the write watermark level is 128. + */ +//@{ +#define BP_SDHC_WML_WRWML (16U) //!< Bit position for SDHC_WML_WRWML. +#define BM_SDHC_WML_WRWML (0x00FF0000U) //!< Bit mask for SDHC_WML_WRWML. +#define BS_SDHC_WML_WRWML (8U) //!< Bit field size in bits for SDHC_WML_WRWML. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_WML_WRWML field. +#define BR_SDHC_WML_WRWML (HW_SDHC_WML.B.WRWML) +#endif + +//! @brief Format value for bitfield SDHC_WML_WRWML. +#define BF_SDHC_WML_WRWML(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_WML_WRWML), uint32_t) & BM_SDHC_WML_WRWML) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the WRWML field to a new value. +#define BW_SDHC_WML_WRWML(v) (HW_SDHC_WML_WR((HW_SDHC_WML_RD() & ~BM_SDHC_WML_WRWML) | BF_SDHC_WML_WRWML(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_FEVT - Force Event register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_FEVT - Force Event register (WO) + * + * Reset value: 0x00000000U + * + * The Force Event (FEVT) register is not a physically implemented register. + * Rather, it is an address at which the Interrupt Status register can be written if + * the corresponding bit of the Interrupt Status Enable register is set. This + * register is a write only register and writing 0 to it has no effect. Writing 1 + * to this register actually sets the corresponding bit of Interrupt Status + * register. A read from this register always results in 0's. To change the + * corresponding status bits in the interrupt status register, make sure to set + * SYSCTL[IPGEN] so that bus clock is always active. Forcing a card interrupt will generate a + * short pulse on the DAT[1] line, and the driver may treat this interrupt as a + * normal interrupt. The interrupt service routine may skip polling the card + * interrupt factor as the interrupt is selfcleared. + */ +typedef union _hw_sdhc_fevt +{ + uint32_t U; + struct _hw_sdhc_fevt_bitfields + { + uint32_t AC12NE : 1; //!< [0] Force Event Auto Command 12 Not Executed + uint32_t AC12TOE : 1; //!< [1] Force Event Auto Command 12 Time Out + //! Error + uint32_t AC12CE : 1; //!< [2] Force Event Auto Command 12 CRC Error + uint32_t AC12EBE : 1; //!< [3] Force Event Auto Command 12 End Bit + //! Error + uint32_t AC12IE : 1; //!< [4] Force Event Auto Command 12 Index Error + uint32_t RESERVED0 : 2; //!< [6:5] + uint32_t CNIBAC12E : 1; //!< [7] Force Event Command Not Executed By + //! Auto Command 12 Error + uint32_t RESERVED1 : 8; //!< [15:8] + uint32_t CTOE : 1; //!< [16] Force Event Command Time Out Error + uint32_t CCE : 1; //!< [17] Force Event Command CRC Error + uint32_t CEBE : 1; //!< [18] Force Event Command End Bit Error + uint32_t CIE : 1; //!< [19] Force Event Command Index Error + uint32_t DTOE : 1; //!< [20] Force Event Data Time Out Error + uint32_t DCE : 1; //!< [21] Force Event Data CRC Error + uint32_t DEBE : 1; //!< [22] Force Event Data End Bit Error + uint32_t RESERVED2 : 1; //!< [23] + uint32_t AC12E : 1; //!< [24] Force Event Auto Command 12 Error + uint32_t RESERVED3 : 3; //!< [27:25] + uint32_t DMAE : 1; //!< [28] Force Event DMA Error + uint32_t RESERVED4 : 2; //!< [30:29] + uint32_t CINT : 1; //!< [31] Force Event Card Interrupt + } B; +} hw_sdhc_fevt_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_FEVT register + */ +//@{ +#define HW_SDHC_FEVT_ADDR (REGS_SDHC_BASE + 0x50U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_FEVT (*(__O hw_sdhc_fevt_t *) HW_SDHC_FEVT_ADDR) +#define HW_SDHC_FEVT_RD() (HW_SDHC_FEVT.U) +#define HW_SDHC_FEVT_WR(v) (HW_SDHC_FEVT.U = (v)) +#endif +//@} + +/* + * Constants & macros for individual SDHC_FEVT bitfields + */ + +/*! + * @name Register SDHC_FEVT, field AC12NE[0] (WORZ) + * + * Forces AC12ERR[AC12NE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12NE (0U) //!< Bit position for SDHC_FEVT_AC12NE. +#define BM_SDHC_FEVT_AC12NE (0x00000001U) //!< Bit mask for SDHC_FEVT_AC12NE. +#define BS_SDHC_FEVT_AC12NE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12NE. + +//! @brief Format value for bitfield SDHC_FEVT_AC12NE. +#define BF_SDHC_FEVT_AC12NE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12NE), uint32_t) & BM_SDHC_FEVT_AC12NE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12NE field to a new value. +#define BW_SDHC_FEVT_AC12NE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12NE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field AC12TOE[1] (WORZ) + * + * Forces AC12ERR[AC12TOE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12TOE (1U) //!< Bit position for SDHC_FEVT_AC12TOE. +#define BM_SDHC_FEVT_AC12TOE (0x00000002U) //!< Bit mask for SDHC_FEVT_AC12TOE. +#define BS_SDHC_FEVT_AC12TOE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12TOE. + +//! @brief Format value for bitfield SDHC_FEVT_AC12TOE. +#define BF_SDHC_FEVT_AC12TOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12TOE), uint32_t) & BM_SDHC_FEVT_AC12TOE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12TOE field to a new value. +#define BW_SDHC_FEVT_AC12TOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12TOE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field AC12CE[2] (WORZ) + * + * Forces AC12ERR[AC12CE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12CE (2U) //!< Bit position for SDHC_FEVT_AC12CE. +#define BM_SDHC_FEVT_AC12CE (0x00000004U) //!< Bit mask for SDHC_FEVT_AC12CE. +#define BS_SDHC_FEVT_AC12CE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12CE. + +//! @brief Format value for bitfield SDHC_FEVT_AC12CE. +#define BF_SDHC_FEVT_AC12CE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12CE), uint32_t) & BM_SDHC_FEVT_AC12CE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12CE field to a new value. +#define BW_SDHC_FEVT_AC12CE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12CE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field AC12EBE[3] (WORZ) + * + * Forces AC12ERR[AC12EBE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12EBE (3U) //!< Bit position for SDHC_FEVT_AC12EBE. +#define BM_SDHC_FEVT_AC12EBE (0x00000008U) //!< Bit mask for SDHC_FEVT_AC12EBE. +#define BS_SDHC_FEVT_AC12EBE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12EBE. + +//! @brief Format value for bitfield SDHC_FEVT_AC12EBE. +#define BF_SDHC_FEVT_AC12EBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12EBE), uint32_t) & BM_SDHC_FEVT_AC12EBE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12EBE field to a new value. +#define BW_SDHC_FEVT_AC12EBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12EBE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field AC12IE[4] (WORZ) + * + * Forces AC12ERR[AC12IE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12IE (4U) //!< Bit position for SDHC_FEVT_AC12IE. +#define BM_SDHC_FEVT_AC12IE (0x00000010U) //!< Bit mask for SDHC_FEVT_AC12IE. +#define BS_SDHC_FEVT_AC12IE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12IE. + +//! @brief Format value for bitfield SDHC_FEVT_AC12IE. +#define BF_SDHC_FEVT_AC12IE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12IE), uint32_t) & BM_SDHC_FEVT_AC12IE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12IE field to a new value. +#define BW_SDHC_FEVT_AC12IE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12IE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CNIBAC12E[7] (WORZ) + * + * Forces AC12ERR[CNIBAC12E] to be set. + */ +//@{ +#define BP_SDHC_FEVT_CNIBAC12E (7U) //!< Bit position for SDHC_FEVT_CNIBAC12E. +#define BM_SDHC_FEVT_CNIBAC12E (0x00000080U) //!< Bit mask for SDHC_FEVT_CNIBAC12E. +#define BS_SDHC_FEVT_CNIBAC12E (1U) //!< Bit field size in bits for SDHC_FEVT_CNIBAC12E. + +//! @brief Format value for bitfield SDHC_FEVT_CNIBAC12E. +#define BF_SDHC_FEVT_CNIBAC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CNIBAC12E), uint32_t) & BM_SDHC_FEVT_CNIBAC12E) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CNIBAC12E field to a new value. +#define BW_SDHC_FEVT_CNIBAC12E(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CNIBAC12E) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CTOE[16] (WORZ) + * + * Forces IRQSTAT[CTOE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_CTOE (16U) //!< Bit position for SDHC_FEVT_CTOE. +#define BM_SDHC_FEVT_CTOE (0x00010000U) //!< Bit mask for SDHC_FEVT_CTOE. +#define BS_SDHC_FEVT_CTOE (1U) //!< Bit field size in bits for SDHC_FEVT_CTOE. + +//! @brief Format value for bitfield SDHC_FEVT_CTOE. +#define BF_SDHC_FEVT_CTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CTOE), uint32_t) & BM_SDHC_FEVT_CTOE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CTOE field to a new value. +#define BW_SDHC_FEVT_CTOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CTOE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CCE[17] (WORZ) + * + * Forces IRQSTAT[CCE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_CCE (17U) //!< Bit position for SDHC_FEVT_CCE. +#define BM_SDHC_FEVT_CCE (0x00020000U) //!< Bit mask for SDHC_FEVT_CCE. +#define BS_SDHC_FEVT_CCE (1U) //!< Bit field size in bits for SDHC_FEVT_CCE. + +//! @brief Format value for bitfield SDHC_FEVT_CCE. +#define BF_SDHC_FEVT_CCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CCE), uint32_t) & BM_SDHC_FEVT_CCE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CCE field to a new value. +#define BW_SDHC_FEVT_CCE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CCE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CEBE[18] (WORZ) + * + * Forces IRQSTAT[CEBE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_CEBE (18U) //!< Bit position for SDHC_FEVT_CEBE. +#define BM_SDHC_FEVT_CEBE (0x00040000U) //!< Bit mask for SDHC_FEVT_CEBE. +#define BS_SDHC_FEVT_CEBE (1U) //!< Bit field size in bits for SDHC_FEVT_CEBE. + +//! @brief Format value for bitfield SDHC_FEVT_CEBE. +#define BF_SDHC_FEVT_CEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CEBE), uint32_t) & BM_SDHC_FEVT_CEBE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CEBE field to a new value. +#define BW_SDHC_FEVT_CEBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CEBE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CIE[19] (WORZ) + * + * Forces IRQSTAT[CCE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_CIE (19U) //!< Bit position for SDHC_FEVT_CIE. +#define BM_SDHC_FEVT_CIE (0x00080000U) //!< Bit mask for SDHC_FEVT_CIE. +#define BS_SDHC_FEVT_CIE (1U) //!< Bit field size in bits for SDHC_FEVT_CIE. + +//! @brief Format value for bitfield SDHC_FEVT_CIE. +#define BF_SDHC_FEVT_CIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CIE), uint32_t) & BM_SDHC_FEVT_CIE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CIE field to a new value. +#define BW_SDHC_FEVT_CIE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CIE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field DTOE[20] (WORZ) + * + * Forces IRQSTAT[DTOE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_DTOE (20U) //!< Bit position for SDHC_FEVT_DTOE. +#define BM_SDHC_FEVT_DTOE (0x00100000U) //!< Bit mask for SDHC_FEVT_DTOE. +#define BS_SDHC_FEVT_DTOE (1U) //!< Bit field size in bits for SDHC_FEVT_DTOE. + +//! @brief Format value for bitfield SDHC_FEVT_DTOE. +#define BF_SDHC_FEVT_DTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DTOE), uint32_t) & BM_SDHC_FEVT_DTOE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOE field to a new value. +#define BW_SDHC_FEVT_DTOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DTOE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field DCE[21] (WORZ) + * + * Forces IRQSTAT[DCE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_DCE (21U) //!< Bit position for SDHC_FEVT_DCE. +#define BM_SDHC_FEVT_DCE (0x00200000U) //!< Bit mask for SDHC_FEVT_DCE. +#define BS_SDHC_FEVT_DCE (1U) //!< Bit field size in bits for SDHC_FEVT_DCE. + +//! @brief Format value for bitfield SDHC_FEVT_DCE. +#define BF_SDHC_FEVT_DCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DCE), uint32_t) & BM_SDHC_FEVT_DCE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DCE field to a new value. +#define BW_SDHC_FEVT_DCE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DCE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field DEBE[22] (WORZ) + * + * Forces IRQSTAT[DEBE] to be set. + */ +//@{ +#define BP_SDHC_FEVT_DEBE (22U) //!< Bit position for SDHC_FEVT_DEBE. +#define BM_SDHC_FEVT_DEBE (0x00400000U) //!< Bit mask for SDHC_FEVT_DEBE. +#define BS_SDHC_FEVT_DEBE (1U) //!< Bit field size in bits for SDHC_FEVT_DEBE. + +//! @brief Format value for bitfield SDHC_FEVT_DEBE. +#define BF_SDHC_FEVT_DEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DEBE), uint32_t) & BM_SDHC_FEVT_DEBE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DEBE field to a new value. +#define BW_SDHC_FEVT_DEBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DEBE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field AC12E[24] (WORZ) + * + * Forces IRQSTAT[AC12E] to be set. + */ +//@{ +#define BP_SDHC_FEVT_AC12E (24U) //!< Bit position for SDHC_FEVT_AC12E. +#define BM_SDHC_FEVT_AC12E (0x01000000U) //!< Bit mask for SDHC_FEVT_AC12E. +#define BS_SDHC_FEVT_AC12E (1U) //!< Bit field size in bits for SDHC_FEVT_AC12E. + +//! @brief Format value for bitfield SDHC_FEVT_AC12E. +#define BF_SDHC_FEVT_AC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12E), uint32_t) & BM_SDHC_FEVT_AC12E) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AC12E field to a new value. +#define BW_SDHC_FEVT_AC12E(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12E) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field DMAE[28] (WORZ) + * + * Forces the DMAE bit of Interrupt Status Register to be set. + */ +//@{ +#define BP_SDHC_FEVT_DMAE (28U) //!< Bit position for SDHC_FEVT_DMAE. +#define BM_SDHC_FEVT_DMAE (0x10000000U) //!< Bit mask for SDHC_FEVT_DMAE. +#define BS_SDHC_FEVT_DMAE (1U) //!< Bit field size in bits for SDHC_FEVT_DMAE. + +//! @brief Format value for bitfield SDHC_FEVT_DMAE. +#define BF_SDHC_FEVT_DMAE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DMAE), uint32_t) & BM_SDHC_FEVT_DMAE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DMAE field to a new value. +#define BW_SDHC_FEVT_DMAE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DMAE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_FEVT, field CINT[31] (WORZ) + * + * Writing 1 to this bit generates a short low-level pulse on the internal + * DAT[1] line, as if a self-clearing interrupt was received from the external card. + * If enabled, the CINT bit will be set and the interrupt service routine may + * treat this interrupt as a normal interrupt from the external card. + */ +//@{ +#define BP_SDHC_FEVT_CINT (31U) //!< Bit position for SDHC_FEVT_CINT. +#define BM_SDHC_FEVT_CINT (0x80000000U) //!< Bit mask for SDHC_FEVT_CINT. +#define BS_SDHC_FEVT_CINT (1U) //!< Bit field size in bits for SDHC_FEVT_CINT. + +//! @brief Format value for bitfield SDHC_FEVT_CINT. +#define BF_SDHC_FEVT_CINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CINT), uint32_t) & BM_SDHC_FEVT_CINT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the CINT field to a new value. +#define BW_SDHC_FEVT_CINT(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CINT) = (v)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_ADMAES - ADMA Error Status register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_ADMAES - ADMA Error Status register (RO) + * + * Reset value: 0x00000000U + * + * When an ADMA error interrupt has occurred, the ADMA Error States field in + * this register holds the ADMA state and the ADMA System Address register holds the + * address around the error descriptor. For recovering from this error, the host + * driver requires the ADMA state to identify the error descriptor address as + * follows: ST_STOP: Previous location set in the ADMA System Address register is + * the error descriptor address. ST_FDS: Current location set in the ADMA System + * Address register is the error descriptor address. ST_CADR: This state is never + * set because it only increments the descriptor pointer and doesn't generate an + * ADMA error. ST_TFR: Previous location set in the ADMA System Address register + * is the error descriptor address. In case of a write operation, the host driver + * must use the ACMD22 to get the number of the written block, rather than using + * this information, because unwritten data may exist in the host controller. + * The host controller generates the ADMA error interrupt when it detects invalid + * descriptor data (valid = 0) in the ST_FDS state. The host driver can + * distinguish this error by reading the valid bit of the error descriptor. ADMA Error + * State coding D01-D00 ADMA Error State when error has occurred Contents of ADMA + * System Address register 00 ST_STOP (Stop DMA) Holds the address of the next + * executable descriptor command 01 ST_FDS (fetch descriptor) Holds the valid + * descriptor address 10 ST_CADR (change address) No ADMA error is generated 11 ST_TFR + * (Transfer Data) Holds the address of the next executable descriptor command + */ +typedef union _hw_sdhc_admaes +{ + uint32_t U; + struct _hw_sdhc_admaes_bitfields + { + uint32_t ADMAES : 2; //!< [1:0] ADMA Error State (When ADMA Error Is + //! Occurred.) + uint32_t ADMALME : 1; //!< [2] ADMA Length Mismatch Error + uint32_t ADMADCE : 1; //!< [3] ADMA Descriptor Error + uint32_t RESERVED0 : 28; //!< [31:4] + } B; +} hw_sdhc_admaes_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_ADMAES register + */ +//@{ +#define HW_SDHC_ADMAES_ADDR (REGS_SDHC_BASE + 0x54U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_ADMAES (*(__I hw_sdhc_admaes_t *) HW_SDHC_ADMAES_ADDR) +#define HW_SDHC_ADMAES_RD() (HW_SDHC_ADMAES.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_ADMAES bitfields + */ + +/*! + * @name Register SDHC_ADMAES, field ADMAES[1:0] (RO) + * + * Indicates the state of the ADMA when an error has occurred during an ADMA + * data transfer. + */ +//@{ +#define BP_SDHC_ADMAES_ADMAES (0U) //!< Bit position for SDHC_ADMAES_ADMAES. +#define BM_SDHC_ADMAES_ADMAES (0x00000003U) //!< Bit mask for SDHC_ADMAES_ADMAES. +#define BS_SDHC_ADMAES_ADMAES (2U) //!< Bit field size in bits for SDHC_ADMAES_ADMAES. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_ADMAES_ADMAES field. +#define BR_SDHC_ADMAES_ADMAES (HW_SDHC_ADMAES.B.ADMAES) +#endif +//@} + +/*! + * @name Register SDHC_ADMAES, field ADMALME[2] (RO) + * + * This error occurs in the following 2 cases: While the block count enable is + * being set, the total data length specified by the descriptor table is different + * from that specified by the block count and block length. Total data length + * can not be divided by the block length. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_ADMAES_ADMALME (2U) //!< Bit position for SDHC_ADMAES_ADMALME. +#define BM_SDHC_ADMAES_ADMALME (0x00000004U) //!< Bit mask for SDHC_ADMAES_ADMALME. +#define BS_SDHC_ADMAES_ADMALME (1U) //!< Bit field size in bits for SDHC_ADMAES_ADMALME. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_ADMAES_ADMALME field. +#define BR_SDHC_ADMAES_ADMALME (BITBAND_ACCESS32(HW_SDHC_ADMAES_ADDR, BP_SDHC_ADMAES_ADMALME)) +#endif +//@} + +/*! + * @name Register SDHC_ADMAES, field ADMADCE[3] (RO) + * + * This error occurs when an invalid descriptor is fetched by ADMA. + * + * Values: + * - 0 - No error. + * - 1 - Error. + */ +//@{ +#define BP_SDHC_ADMAES_ADMADCE (3U) //!< Bit position for SDHC_ADMAES_ADMADCE. +#define BM_SDHC_ADMAES_ADMADCE (0x00000008U) //!< Bit mask for SDHC_ADMAES_ADMADCE. +#define BS_SDHC_ADMAES_ADMADCE (1U) //!< Bit field size in bits for SDHC_ADMAES_ADMADCE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_ADMAES_ADMADCE field. +#define BR_SDHC_ADMAES_ADMADCE (BITBAND_ACCESS32(HW_SDHC_ADMAES_ADDR, BP_SDHC_ADMAES_ADMADCE)) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_ADSADDR - ADMA System Addressregister +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_ADSADDR - ADMA System Addressregister (RW) + * + * Reset value: 0x00000000U + * + * This register contains the physical system memory address used for ADMA + * transfers. + */ +typedef union _hw_sdhc_adsaddr +{ + uint32_t U; + struct _hw_sdhc_adsaddr_bitfields + { + uint32_t RESERVED0 : 2; //!< [1:0] + uint32_t ADSADDR : 30; //!< [31:2] ADMA System Address + } B; +} hw_sdhc_adsaddr_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_ADSADDR register + */ +//@{ +#define HW_SDHC_ADSADDR_ADDR (REGS_SDHC_BASE + 0x58U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_ADSADDR (*(__IO hw_sdhc_adsaddr_t *) HW_SDHC_ADSADDR_ADDR) +#define HW_SDHC_ADSADDR_RD() (HW_SDHC_ADSADDR.U) +#define HW_SDHC_ADSADDR_WR(v) (HW_SDHC_ADSADDR.U = (v)) +#define HW_SDHC_ADSADDR_SET(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() | (v))) +#define HW_SDHC_ADSADDR_CLR(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() & ~(v))) +#define HW_SDHC_ADSADDR_TOG(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_ADSADDR bitfields + */ + +/*! + * @name Register SDHC_ADSADDR, field ADSADDR[31:2] (RW) + * + * Holds the word address of the executing command in the descriptor table. At + * the start of ADMA, the host driver shall set the start address of the + * Descriptor table. The ADMA engine increments this register address whenever fetching a + * descriptor command. When the ADMA is stopped at the block gap, this register + * indicates the address of the next executable descriptor command. When the ADMA + * error interrupt is generated, this register shall hold the valid descriptor + * address depending on the ADMA state. The lower 2 bits of this register is tied + * to '0' so the ADMA address is always word-aligned. Because this register + * supports dynamic address reflecting, when TC bit is set, it automatically alters the + * value of internal address counter, so SW cannot change this register when TC + * bit is set. + */ +//@{ +#define BP_SDHC_ADSADDR_ADSADDR (2U) //!< Bit position for SDHC_ADSADDR_ADSADDR. +#define BM_SDHC_ADSADDR_ADSADDR (0xFFFFFFFCU) //!< Bit mask for SDHC_ADSADDR_ADSADDR. +#define BS_SDHC_ADSADDR_ADSADDR (30U) //!< Bit field size in bits for SDHC_ADSADDR_ADSADDR. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_ADSADDR_ADSADDR field. +#define BR_SDHC_ADSADDR_ADSADDR (HW_SDHC_ADSADDR.B.ADSADDR) +#endif + +//! @brief Format value for bitfield SDHC_ADSADDR_ADSADDR. +#define BF_SDHC_ADSADDR_ADSADDR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_ADSADDR_ADSADDR), uint32_t) & BM_SDHC_ADSADDR_ADSADDR) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the ADSADDR field to a new value. +#define BW_SDHC_ADSADDR_ADSADDR(v) (HW_SDHC_ADSADDR_WR((HW_SDHC_ADSADDR_RD() & ~BM_SDHC_ADSADDR_ADSADDR) | BF_SDHC_ADSADDR_ADSADDR(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_VENDOR - Vendor Specific register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_VENDOR - Vendor Specific register (RW) + * + * Reset value: 0x00000001U + * + * This register contains the vendor-specific control/status register. + */ +typedef union _hw_sdhc_vendor +{ + uint32_t U; + struct _hw_sdhc_vendor_bitfields + { + uint32_t EXTDMAEN : 1; //!< [0] External DMA Request Enable + uint32_t EXBLKNU : 1; //!< [1] Exact Block Number Block Read Enable + //! For SDIO CMD53 + uint32_t RESERVED0 : 14; //!< [15:2] + uint32_t INTSTVAL : 8; //!< [23:16] Internal State Value + uint32_t RESERVED1 : 8; //!< [31:24] + } B; +} hw_sdhc_vendor_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_VENDOR register + */ +//@{ +#define HW_SDHC_VENDOR_ADDR (REGS_SDHC_BASE + 0xC0U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_VENDOR (*(__IO hw_sdhc_vendor_t *) HW_SDHC_VENDOR_ADDR) +#define HW_SDHC_VENDOR_RD() (HW_SDHC_VENDOR.U) +#define HW_SDHC_VENDOR_WR(v) (HW_SDHC_VENDOR.U = (v)) +#define HW_SDHC_VENDOR_SET(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() | (v))) +#define HW_SDHC_VENDOR_CLR(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() & ~(v))) +#define HW_SDHC_VENDOR_TOG(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_VENDOR bitfields + */ + +/*! + * @name Register SDHC_VENDOR, field EXTDMAEN[0] (RW) + * + * Enables the request to external DMA. When the internal DMA (either simple DMA + * or advanced DMA) is not in use, and this bit is set, SDHC will send out DMA + * request when the internal buffer is ready. This bit is particularly useful when + * transferring data by CPU polling mode, and it is not allowed to send out the + * external DMA request. By default, this bit is set. + * + * Values: + * - 0 - In any scenario, SDHC does not send out the external DMA request. + * - 1 - When internal DMA is not active, the external DMA request will be sent + * out. + */ +//@{ +#define BP_SDHC_VENDOR_EXTDMAEN (0U) //!< Bit position for SDHC_VENDOR_EXTDMAEN. +#define BM_SDHC_VENDOR_EXTDMAEN (0x00000001U) //!< Bit mask for SDHC_VENDOR_EXTDMAEN. +#define BS_SDHC_VENDOR_EXTDMAEN (1U) //!< Bit field size in bits for SDHC_VENDOR_EXTDMAEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_VENDOR_EXTDMAEN field. +#define BR_SDHC_VENDOR_EXTDMAEN (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXTDMAEN)) +#endif + +//! @brief Format value for bitfield SDHC_VENDOR_EXTDMAEN. +#define BF_SDHC_VENDOR_EXTDMAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_VENDOR_EXTDMAEN), uint32_t) & BM_SDHC_VENDOR_EXTDMAEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the EXTDMAEN field to a new value. +#define BW_SDHC_VENDOR_EXTDMAEN(v) (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXTDMAEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_VENDOR, field EXBLKNU[1] (RW) + * + * This bit must be set before S/W issues CMD53 multi-block read with exact + * block number. This bit must not be set if the CMD53 multi-block read is not exact + * block number. + * + * Values: + * - 0 - None exact block read. + * - 1 - Exact block read for SDIO CMD53. + */ +//@{ +#define BP_SDHC_VENDOR_EXBLKNU (1U) //!< Bit position for SDHC_VENDOR_EXBLKNU. +#define BM_SDHC_VENDOR_EXBLKNU (0x00000002U) //!< Bit mask for SDHC_VENDOR_EXBLKNU. +#define BS_SDHC_VENDOR_EXBLKNU (1U) //!< Bit field size in bits for SDHC_VENDOR_EXBLKNU. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_VENDOR_EXBLKNU field. +#define BR_SDHC_VENDOR_EXBLKNU (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXBLKNU)) +#endif + +//! @brief Format value for bitfield SDHC_VENDOR_EXBLKNU. +#define BF_SDHC_VENDOR_EXBLKNU(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_VENDOR_EXBLKNU), uint32_t) & BM_SDHC_VENDOR_EXBLKNU) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the EXBLKNU field to a new value. +#define BW_SDHC_VENDOR_EXBLKNU(v) (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXBLKNU) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_VENDOR, field INTSTVAL[23:16] (RO) + * + * Internal state value, reflecting the corresponding state value selected by + * Debug Select field. This field is read-only and write to this field does not + * have effect. + */ +//@{ +#define BP_SDHC_VENDOR_INTSTVAL (16U) //!< Bit position for SDHC_VENDOR_INTSTVAL. +#define BM_SDHC_VENDOR_INTSTVAL (0x00FF0000U) //!< Bit mask for SDHC_VENDOR_INTSTVAL. +#define BS_SDHC_VENDOR_INTSTVAL (8U) //!< Bit field size in bits for SDHC_VENDOR_INTSTVAL. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_VENDOR_INTSTVAL field. +#define BR_SDHC_VENDOR_INTSTVAL (HW_SDHC_VENDOR.B.INTSTVAL) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_MMCBOOT - MMC Boot register +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_MMCBOOT - MMC Boot register (RW) + * + * Reset value: 0x00000000U + * + * This register contains the MMC fast boot control register. + */ +typedef union _hw_sdhc_mmcboot +{ + uint32_t U; + struct _hw_sdhc_mmcboot_bitfields + { + uint32_t DTOCVACK : 4; //!< [3:0] Boot ACK Time Out Counter Value + uint32_t BOOTACK : 1; //!< [4] Boot Ack Mode Select + uint32_t BOOTMODE : 1; //!< [5] Boot Mode Select + uint32_t BOOTEN : 1; //!< [6] Boot Mode Enable + uint32_t AUTOSABGEN : 1; //!< [7] + uint32_t RESERVED0 : 8; //!< [15:8] + uint32_t BOOTBLKCNT : 16; //!< [31:16] + } B; +} hw_sdhc_mmcboot_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_MMCBOOT register + */ +//@{ +#define HW_SDHC_MMCBOOT_ADDR (REGS_SDHC_BASE + 0xC4U) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_MMCBOOT (*(__IO hw_sdhc_mmcboot_t *) HW_SDHC_MMCBOOT_ADDR) +#define HW_SDHC_MMCBOOT_RD() (HW_SDHC_MMCBOOT.U) +#define HW_SDHC_MMCBOOT_WR(v) (HW_SDHC_MMCBOOT.U = (v)) +#define HW_SDHC_MMCBOOT_SET(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() | (v))) +#define HW_SDHC_MMCBOOT_CLR(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() & ~(v))) +#define HW_SDHC_MMCBOOT_TOG(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() ^ (v))) +#endif +//@} + +/* + * Constants & macros for individual SDHC_MMCBOOT bitfields + */ + +/*! + * @name Register SDHC_MMCBOOT, field DTOCVACK[3:0] (RW) + * + * Values: + * - 0000 - SDCLK x 2^8 + * - 0001 - SDCLK x 2^9 + * - 0010 - SDCLK x 2^10 + * - 0011 - SDCLK x 2^11 + * - 0100 - SDCLK x 2^12 + * - 0101 - SDCLK x 2^13 + * - 0110 - SDCLK x 2^14 + * - 0111 - SDCLK x 2^15 + * - 1110 - SDCLK x 2^22 + * - 1111 - Reserved + */ +//@{ +#define BP_SDHC_MMCBOOT_DTOCVACK (0U) //!< Bit position for SDHC_MMCBOOT_DTOCVACK. +#define BM_SDHC_MMCBOOT_DTOCVACK (0x0000000FU) //!< Bit mask for SDHC_MMCBOOT_DTOCVACK. +#define BS_SDHC_MMCBOOT_DTOCVACK (4U) //!< Bit field size in bits for SDHC_MMCBOOT_DTOCVACK. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_DTOCVACK field. +#define BR_SDHC_MMCBOOT_DTOCVACK (HW_SDHC_MMCBOOT.B.DTOCVACK) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_DTOCVACK. +#define BF_SDHC_MMCBOOT_DTOCVACK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_DTOCVACK), uint32_t) & BM_SDHC_MMCBOOT_DTOCVACK) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the DTOCVACK field to a new value. +#define BW_SDHC_MMCBOOT_DTOCVACK(v) (HW_SDHC_MMCBOOT_WR((HW_SDHC_MMCBOOT_RD() & ~BM_SDHC_MMCBOOT_DTOCVACK) | BF_SDHC_MMCBOOT_DTOCVACK(v))) +#endif +//@} + +/*! + * @name Register SDHC_MMCBOOT, field BOOTACK[4] (RW) + * + * Values: + * - 0 - No ack. + * - 1 - Ack. + */ +//@{ +#define BP_SDHC_MMCBOOT_BOOTACK (4U) //!< Bit position for SDHC_MMCBOOT_BOOTACK. +#define BM_SDHC_MMCBOOT_BOOTACK (0x00000010U) //!< Bit mask for SDHC_MMCBOOT_BOOTACK. +#define BS_SDHC_MMCBOOT_BOOTACK (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTACK. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_BOOTACK field. +#define BR_SDHC_MMCBOOT_BOOTACK (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTACK)) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_BOOTACK. +#define BF_SDHC_MMCBOOT_BOOTACK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTACK), uint32_t) & BM_SDHC_MMCBOOT_BOOTACK) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BOOTACK field to a new value. +#define BW_SDHC_MMCBOOT_BOOTACK(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTACK) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_MMCBOOT, field BOOTMODE[5] (RW) + * + * Values: + * - 0 - Normal boot. + * - 1 - Alternative boot. + */ +//@{ +#define BP_SDHC_MMCBOOT_BOOTMODE (5U) //!< Bit position for SDHC_MMCBOOT_BOOTMODE. +#define BM_SDHC_MMCBOOT_BOOTMODE (0x00000020U) //!< Bit mask for SDHC_MMCBOOT_BOOTMODE. +#define BS_SDHC_MMCBOOT_BOOTMODE (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTMODE. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_BOOTMODE field. +#define BR_SDHC_MMCBOOT_BOOTMODE (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTMODE)) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_BOOTMODE. +#define BF_SDHC_MMCBOOT_BOOTMODE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTMODE), uint32_t) & BM_SDHC_MMCBOOT_BOOTMODE) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BOOTMODE field to a new value. +#define BW_SDHC_MMCBOOT_BOOTMODE(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTMODE) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_MMCBOOT, field BOOTEN[6] (RW) + * + * Values: + * - 0 - Fast boot disable. + * - 1 - Fast boot enable. + */ +//@{ +#define BP_SDHC_MMCBOOT_BOOTEN (6U) //!< Bit position for SDHC_MMCBOOT_BOOTEN. +#define BM_SDHC_MMCBOOT_BOOTEN (0x00000040U) //!< Bit mask for SDHC_MMCBOOT_BOOTEN. +#define BS_SDHC_MMCBOOT_BOOTEN (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_BOOTEN field. +#define BR_SDHC_MMCBOOT_BOOTEN (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTEN)) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_BOOTEN. +#define BF_SDHC_MMCBOOT_BOOTEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTEN), uint32_t) & BM_SDHC_MMCBOOT_BOOTEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BOOTEN field to a new value. +#define BW_SDHC_MMCBOOT_BOOTEN(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_MMCBOOT, field AUTOSABGEN[7] (RW) + * + * When boot, enable auto stop at block gap function. This function will be + * triggered, and host will stop at block gap when received card block cnt is equal + * to BOOTBLKCNT. + */ +//@{ +#define BP_SDHC_MMCBOOT_AUTOSABGEN (7U) //!< Bit position for SDHC_MMCBOOT_AUTOSABGEN. +#define BM_SDHC_MMCBOOT_AUTOSABGEN (0x00000080U) //!< Bit mask for SDHC_MMCBOOT_AUTOSABGEN. +#define BS_SDHC_MMCBOOT_AUTOSABGEN (1U) //!< Bit field size in bits for SDHC_MMCBOOT_AUTOSABGEN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_AUTOSABGEN field. +#define BR_SDHC_MMCBOOT_AUTOSABGEN (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_AUTOSABGEN)) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_AUTOSABGEN. +#define BF_SDHC_MMCBOOT_AUTOSABGEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_AUTOSABGEN), uint32_t) & BM_SDHC_MMCBOOT_AUTOSABGEN) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the AUTOSABGEN field to a new value. +#define BW_SDHC_MMCBOOT_AUTOSABGEN(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_AUTOSABGEN) = (v)) +#endif +//@} + +/*! + * @name Register SDHC_MMCBOOT, field BOOTBLKCNT[31:16] (RW) + * + * Defines the stop at block gap value of automatic mode. When received card + * block cnt is equal to BOOTBLKCNT and AUTOSABGEN is 1, then stop at block gap. + */ +//@{ +#define BP_SDHC_MMCBOOT_BOOTBLKCNT (16U) //!< Bit position for SDHC_MMCBOOT_BOOTBLKCNT. +#define BM_SDHC_MMCBOOT_BOOTBLKCNT (0xFFFF0000U) //!< Bit mask for SDHC_MMCBOOT_BOOTBLKCNT. +#define BS_SDHC_MMCBOOT_BOOTBLKCNT (16U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTBLKCNT. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_MMCBOOT_BOOTBLKCNT field. +#define BR_SDHC_MMCBOOT_BOOTBLKCNT (HW_SDHC_MMCBOOT.B.BOOTBLKCNT) +#endif + +//! @brief Format value for bitfield SDHC_MMCBOOT_BOOTBLKCNT. +#define BF_SDHC_MMCBOOT_BOOTBLKCNT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTBLKCNT), uint32_t) & BM_SDHC_MMCBOOT_BOOTBLKCNT) + +#ifndef __LANGUAGE_ASM__ +//! @brief Set the BOOTBLKCNT field to a new value. +#define BW_SDHC_MMCBOOT_BOOTBLKCNT(v) (HW_SDHC_MMCBOOT_WR((HW_SDHC_MMCBOOT_RD() & ~BM_SDHC_MMCBOOT_BOOTBLKCNT) | BF_SDHC_MMCBOOT_BOOTBLKCNT(v))) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// HW_SDHC_HOSTVER - Host Controller Version +//------------------------------------------------------------------------------------------- + +#ifndef __LANGUAGE_ASM__ +/*! + * @brief HW_SDHC_HOSTVER - Host Controller Version (RO) + * + * Reset value: 0x00001201U + * + * This register contains the vendor host controller version information. All + * bits are read only and will read the same as the power-reset value. + */ +typedef union _hw_sdhc_hostver +{ + uint32_t U; + struct _hw_sdhc_hostver_bitfields + { + uint32_t SVN : 8; //!< [7:0] Specification Version Number + uint32_t VVN : 8; //!< [15:8] Vendor Version Number + uint32_t RESERVED0 : 16; //!< [31:16] + } B; +} hw_sdhc_hostver_t; +#endif + +/*! + * @name Constants and macros for entire SDHC_HOSTVER register + */ +//@{ +#define HW_SDHC_HOSTVER_ADDR (REGS_SDHC_BASE + 0xFCU) + +#ifndef __LANGUAGE_ASM__ +#define HW_SDHC_HOSTVER (*(__I hw_sdhc_hostver_t *) HW_SDHC_HOSTVER_ADDR) +#define HW_SDHC_HOSTVER_RD() (HW_SDHC_HOSTVER.U) +#endif +//@} + +/* + * Constants & macros for individual SDHC_HOSTVER bitfields + */ + +/*! + * @name Register SDHC_HOSTVER, field SVN[7:0] (RO) + * + * These status bits indicate the host controller specification version. + * + * Values: + * - 1 - SD host specification version 2.0, supports test event register and + * ADMA. + */ +//@{ +#define BP_SDHC_HOSTVER_SVN (0U) //!< Bit position for SDHC_HOSTVER_SVN. +#define BM_SDHC_HOSTVER_SVN (0x000000FFU) //!< Bit mask for SDHC_HOSTVER_SVN. +#define BS_SDHC_HOSTVER_SVN (8U) //!< Bit field size in bits for SDHC_HOSTVER_SVN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HOSTVER_SVN field. +#define BR_SDHC_HOSTVER_SVN (HW_SDHC_HOSTVER.B.SVN) +#endif +//@} + +/*! + * @name Register SDHC_HOSTVER, field VVN[15:8] (RO) + * + * These status bits are reserved for the vendor version number. The host driver + * shall not use this status. + * + * Values: + * - 0 - Freescale SDHC version 1.0 + * - 10000 - Freescale SDHC version 2.0 + * - 10001 - Freescale SDHC version 2.1 + * - 10010 - Freescale SDHC version 2.2 + */ +//@{ +#define BP_SDHC_HOSTVER_VVN (8U) //!< Bit position for SDHC_HOSTVER_VVN. +#define BM_SDHC_HOSTVER_VVN (0x0000FF00U) //!< Bit mask for SDHC_HOSTVER_VVN. +#define BS_SDHC_HOSTVER_VVN (8U) //!< Bit field size in bits for SDHC_HOSTVER_VVN. + +#ifndef __LANGUAGE_ASM__ +//! @brief Read current value of the SDHC_HOSTVER_VVN field. +#define BR_SDHC_HOSTVER_VVN (HW_SDHC_HOSTVER.B.VVN) +#endif +//@} + +//------------------------------------------------------------------------------------------- +// hw_sdhc_t - module struct +//------------------------------------------------------------------------------------------- +/*! + * @brief All SDHC module registers. + */ +#ifndef __LANGUAGE_ASM__ +#pragma pack(1) +typedef struct _hw_sdhc +{ + __IO hw_sdhc_dsaddr_t DSADDR; //!< [0x0] DMA System Address register + __IO hw_sdhc_blkattr_t BLKATTR; //!< [0x4] Block Attributes register + __IO hw_sdhc_cmdarg_t CMDARG; //!< [0x8] Command Argument register + __IO hw_sdhc_xfertyp_t XFERTYP; //!< [0xC] Transfer Type register + __I hw_sdhc_cmdrsp0_t CMDRSP0; //!< [0x10] Command Response 0 + __I hw_sdhc_cmdrsp1_t CMDRSP1; //!< [0x14] Command Response 1 + __I hw_sdhc_cmdrsp2_t CMDRSP2; //!< [0x18] Command Response 2 + __I hw_sdhc_cmdrsp3_t CMDRSP3; //!< [0x1C] Command Response 3 + __IO hw_sdhc_datport_t DATPORT; //!< [0x20] Buffer Data Port register + __I hw_sdhc_prsstat_t PRSSTAT; //!< [0x24] Present State register + __IO hw_sdhc_proctl_t PROCTL; //!< [0x28] Protocol Control register + __IO hw_sdhc_sysctl_t SYSCTL; //!< [0x2C] System Control register + __IO hw_sdhc_irqstat_t IRQSTAT; //!< [0x30] Interrupt Status register + __IO hw_sdhc_irqstaten_t IRQSTATEN; //!< [0x34] Interrupt Status Enable register + __IO hw_sdhc_irqsigen_t IRQSIGEN; //!< [0x38] Interrupt Signal Enable register + __I hw_sdhc_ac12err_t AC12ERR; //!< [0x3C] Auto CMD12 Error Status Register + __I hw_sdhc_htcapblt_t HTCAPBLT; //!< [0x40] Host Controller Capabilities + __IO hw_sdhc_wml_t WML; //!< [0x44] Watermark Level Register + uint8_t _reserved0[8]; + __O hw_sdhc_fevt_t FEVT; //!< [0x50] Force Event register + __I hw_sdhc_admaes_t ADMAES; //!< [0x54] ADMA Error Status register + __IO hw_sdhc_adsaddr_t ADSADDR; //!< [0x58] ADMA System Addressregister + uint8_t _reserved1[100]; + __IO hw_sdhc_vendor_t VENDOR; //!< [0xC0] Vendor Specific register + __IO hw_sdhc_mmcboot_t MMCBOOT; //!< [0xC4] MMC Boot register + uint8_t _reserved2[52]; + __I hw_sdhc_hostver_t HOSTVER; //!< [0xFC] Host Controller Version +} hw_sdhc_t; +#pragma pack() + +//! @brief Macro to access all SDHC registers. +//! @return Reference (not a pointer) to the registers struct. To get a pointer to the struct, +//! use the '&' operator, like <code>&HW_SDHC</code>. +#define HW_SDHC (*(hw_sdhc_t *) REGS_SDHC_BASE) +#endif + +#endif // __HW_SDHC_REGISTERS_H__ +// v22/130726/0.9 +// EOF