mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F401RE/stm32f4xx_hal_pwr.c
- Revision:
- 87:085cde657901
- Child:
- 106:ced8cbb51063
diff -r 26fc69fd3b6c -r 085cde657901 targets/cmsis/TARGET_STM/TARGET_NUCLEO_F401RE/stm32f4xx_hal_pwr.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F401RE/stm32f4xx_hal_pwr.c Sat Feb 08 19:45:06 2014 +0000 @@ -0,0 +1,520 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_pwr.c + * @author MCD Application Team + * @version V1.0.0RC2 + * @date 04-February-2014 + * @brief PWR HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Power Controller (PWR) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @defgroup PWR + * @brief PWR HAL module driver + * @{ + */ + +#ifdef HAL_PWR_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup PWR_Private_Functions + * @{ + */ + +/** @defgroup PWR_Group1 Initialization and de-initialization functions + * @brief Initialization and de-initialization functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + After reset, the backup domain (RTC registers, RTC backup data + registers and backup SRAM) is protected against possible unwanted + write accesses. + To enable access to the RTC Domain and RTC registers, proceed as follows: + (+) Enable the Power Controller (PWR) APB1 interface clock using the + __PWR_CLK_ENABLE() macro. + (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the HAL PWR peripheral registers to their default reset values. + * @param None + * @retval None + */ +void HAL_PWR_DeInit(void) +{ + __PWR_FORCE_RESET(); + __PWR_RELEASE_RESET(); +} + +/** + * @brief Enables access to the backup domain (RTC registers, RTC + * backup data registers and backup SRAM). + * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * Backup Domain Access should be kept enabled. + * @param None + * @retval None + */ +void HAL_PWR_EnableBkUpAccess(void) +{ + *(__IO uint32_t *) CR_DBP_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables access to the backup domain (RTC registers, RTC + * backup data registers and backup SRAM). + * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * Backup Domain Access should be kept enabled. + * @param None + * @retval None + */ +void HAL_PWR_DisableBkUpAccess(void) +{ + *(__IO uint32_t *) CR_DBP_BB = (uint32_t)DISABLE; +} + +/** + * @} + */ + +/** @defgroup PWR_Group2 Peripheral Control functions + * @brief Low Power modes configuration functions + * +@verbatim + + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + + *** PVD configuration *** + ========================= + [..] + (+) The PVD is used to monitor the VDD power supply by comparing it to a + threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR). + (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower + than the PVD threshold. This event is internally connected to the EXTI + line16 and can generate an interrupt if enabled. This is done through + __HAL_PVD_EXTI_ENABLE_IT() macro. + (+) The PVD is stopped in Standby mode. + + *** WakeUp pin configuration *** + ================================ + [..] + (+) WakeUp pin is used to wake up the system from Standby mode. This pin is + forced in input pull-down configuration and is active on rising edges. + (+) There is only one WakeUp pin: WakeUp Pin 1 on PA.00. + + *** Low Power modes configuration *** + ===================================== + [..] + The devices feature 3 low-power modes: + (+) Sleep mode: Cortex-M4 core stopped, peripherals kept running. + (+) Stop mode: all clocks are stopped, regulator running, regulator + in low power mode + (+) Standby mode: 1.2V domain powered off. + + *** Sleep mode *** + ================== + [..] + (+) Entry: + The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFI) + functions with + (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction + (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction + + -@@- The Regulator parameter is not used for the STM32F4 family + and is kept as parameter just to maintain compatibility with the + lower power families (STM32L). + (+) Exit: + Any peripheral interrupt acknowledged by the nested vectored interrupt + controller (NVIC) can wake up the device from Sleep mode. + + *** Stop mode *** + ================= + [..] + In Stop mode, all clocks in the 1.2V domain are stopped, the PLL, the HSI, + and the HSE RC oscillators are disabled. Internal SRAM and register contents + are preserved. + The voltage regulator can be configured either in normal or low-power mode. + To minimize the consumption In Stop mode, FLASH can be powered off before + entering the Stop mode using the HAL_PWR_EnableFlashPowerDown() function. + It can be switched on again by software after exiting the Stop mode using + the HAL_PWR_DisableFlashPowerDown() function. + + (+) Entry: + The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON) + function with: + (++) Main regulator ON. + (++) Low Power regulator ON. + (+) Exit: + Any EXTI Line (Internal or External) configured in Interrupt/Event mode. + + *** Standby mode *** + ==================== + [..] + (+) + The Standby mode allows to achieve the lowest power consumption. It is based + on the Cortex-M4 deep sleep mode, with the voltage regulator disabled. + The 1.2V domain is consequently powered off. The PLL, the HSI oscillator and + the HSE oscillator are also switched off. SRAM and register contents are lost + except for the RTC registers, RTC backup registers, backup SRAM and Standby + circuitry. + + The voltage regulator is OFF. + + (++) Entry: + (+++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function. + (++) Exit: + (+++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wakeup, + tamper event, time-stamp event, external reset in NRST pin, IWDG reset. + + *** Auto-wakeup (AWU) from low-power mode *** + ============================================= + [..] + + (+) The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC + Wakeup event, a tamper event or a time-stamp event, without depending on + an external interrupt (Auto-wakeup mode). + + (+) RTC auto-wakeup (AWU) from the Stop and Standby modes + + (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to + configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. + + (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it + is necessary to configure the RTC to detect the tamper or time stamp event using the + HAL_RTCEx_SetTimeStamp_IT() or HAL_RTCEx_SetTamper_IT() functions. + + (++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to + configure the RTC to generate the RTC WakeUp event using the HAL_RTCEx_SetWakeUpTimer_IT() function. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). + * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration + * information for the PVD. + * @note Refer to the electrical characteristics of your device datasheet for + * more details about the voltage threshold corresponding to each + * detection level. + * @retval None + */ +void HAL_PWR_PVDConfig(PWR_PVDTypeDef *sConfigPVD) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); + assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); + + tmpreg = PWR->CR; + + /* Clear PLS[7:5] bits */ + tmpreg &= ~ (uint32_t)PWR_CR_PLS; + + /* Set PLS[7:5] bits according to PVDLevel value */ + tmpreg |= sConfigPVD->PVDLevel; + + /* Store the new value */ + PWR->CR = tmpreg; + + /* Configure the EXTI 16 interrupt */ + if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\ + (sConfigPVD->Mode == PWR_MODE_IT_FALLING) ||\ + (sConfigPVD->Mode == PWR_MODE_IT_RISING)) + { + __HAL_PVD_EXTI_ENABLE_IT(PWR_EXTI_LINE_PVD); + } + /* Configure the rising edge */ + if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\ + (sConfigPVD->Mode == PWR_MODE_IT_RISING)) + { + EXTI->RTSR |= PWR_EXTI_LINE_PVD; + } + /* Configure the falling edge */ + if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\ + (sConfigPVD->Mode == PWR_MODE_IT_FALLING)) + { + EXTI->FTSR |= PWR_EXTI_LINE_PVD; + } +} + +/** + * @brief Enables the Power Voltage Detector(PVD). + * @param None + * @retval None + */ +void HAL_PWR_EnablePVD(void) +{ + *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the Power Voltage Detector(PVD). + * @param None + * @retval None + */ +void HAL_PWR_DisablePVD(void) +{ + *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)DISABLE; +} + +/** + * @brief Enables the WakeUp PINx functionality. + * @param WakeUpPinx: Specifies the Power Wake-Up pin to enable + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN1 + * @retval None + */ +void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx) +{ + /* Check the parameter */ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); + *(__IO uint32_t *) CSR_EWUP_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the WakeUp PINx functionality. + * @param WakeUpPinx: Specifies the Power Wake-Up pin to disable + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN1 + * @retval None + */ +void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) +{ + /* Check the parameter */ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); + *(__IO uint32_t *) CSR_EWUP_BB = (uint32_t)DISABLE; +} + +/** + * @brief Enters Sleep mode. + * + * @note In Sleep mode, all I/O pins keep the same state as in Run mode. + * + * @note In Sleep mode, the systick is stopped to avoid exit from this mode with + * systick interrupt when used as time base for Timeout + * + * @param Regulator: Specifies the regulator state in SLEEP mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON + * @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON + * @note This parameter is not used for the STM32F4 family and is kept as parameter + * just to maintain compatibility with the lower power families. + * @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction + * @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction + * @retval None + */ +void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) +{ + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(Regulator)); + assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry)); + + /* Disable SysTick Timer */ + SysTick->CTRL &= 0xFE; + + /* Select SLEEP mode entry -------------------------------------------------*/ + if(SLEEPEntry == PWR_SLEEPENTRY_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __WFE(); + } + + /* Enable SysTick Timer */ + SysTick->CTRL |= 0x01; +} + +/** + * @brief Enters Stop mode. + * @note In Stop mode, all I/O pins keep the same state as in Run mode. + * @note When exiting Stop mode by issuing an interrupt or a wakeup event, + * the HSI RC oscillator is selected as system clock. + * @note When the voltage regulator operates in low power mode, an additional + * startup delay is incurred when waking up from Stop mode. + * By keeping the internal regulator ON during Stop mode, the consumption + * is higher although the startup time is reduced. + * @param Regulator: Specifies the regulator state in Stop mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON + * @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON + * @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction + * @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction + * @retval None + */ +void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(Regulator)); + assert_param(IS_PWR_STOP_ENTRY(STOPEntry)); + + /* Select the regulator state in Stop mode ---------------------------------*/ + tmpreg = PWR->CR; + /* Clear PDDS and LPDS bits */ + tmpreg &= (uint32_t)~(PWR_CR_PDDS | PWR_CR_LPDS); + + /* Set LPDS, MRLVDS and LPLVDS bits according to Regulator value */ + tmpreg |= Regulator; + + /* Store the new value */ + PWR->CR = tmpreg; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + + /* Select Stop mode entry --------------------------------------------------*/ + if(STOPEntry == PWR_STOPENTRY_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __WFE(); + } + /* Reset SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); +} + +/** + * @brief Enters Standby mode. + * @note In Standby mode, all I/O pins are high impedance except for: + * - Reset pad (still available) + * - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC + * Alarm out, or RTC clock calibration out. + * - RTC_AF2 pin (PI8) if configured for tamper or time-stamp. + * - WKUP pin 1 (PA0) if enabled. + * @param None + * @retval None + */ +void HAL_PWR_EnterSTANDBYMode(void) +{ + /* Clear Wakeup flag */ + PWR->CR |= PWR_CR_CWUF; + + /* Select Standby mode */ + PWR->CR |= PWR_CR_PDDS; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + + /* This option is used to ensure that store operations are completed */ +#if defined ( __CC_ARM) + __force_stores(); +#endif + /* Request Wait For Interrupt */ + __WFI(); +} + +/** + * @brief This function handles the PWR PVD interrupt request. + * @note This API should be called under the PVD_IRQHandler(). + * @param None + * @retval None + */ +void HAL_PWR_PVD_IRQHandler(void) +{ + /* Check PWR exti flag */ + if(__HAL_PVD_EXTI_GET_FLAG(PWR_EXTI_LINE_PVD) != RESET) + { + /* PWR PVD interrupt user callback */ + HAL_PWR_PVDCallback(); + + /* Clear PWR Exti pending bit */ + __HAL_PVD_EXTI_CLEAR_FLAG(PWR_EXTI_LINE_PVD); + } +} + +/** + * @brief PWR PVD interrupt callback + * @param none + * @retval none + */ +__weak void HAL_PWR_PVDCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_PWR_PVDCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_PWR_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/