mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
targets/hal/TARGET_Freescale/TARGET_KSDK_MCUS/TARGET_K64F/device/MK64F12/MK64F12_i2c.h
- Committer:
- mbed_official
- Date:
- 2014-04-02
- Revision:
- 146:f64d43ff0c18
File content as of revision 146:f64d43ff0c18:
/* * Copyright (c) 2014, Freescale Semiconductor, Inc. * All rights reserved. * * THIS SOFTWARE IS PROVIDED BY FREESCALE "AS IS" AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT * SHALL FREESCALE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY * OF SUCH DAMAGE. */ /* * WARNING! DO NOT EDIT THIS FILE DIRECTLY! * * This file was generated automatically and any changes may be lost. */ #ifndef __HW_I2C_REGISTERS_H__ #define __HW_I2C_REGISTERS_H__ #include "regs.h" /* * MK64F12 I2C * * Inter-Integrated Circuit * * Registers defined in this header file: * - HW_I2C_A1 - I2C Address Register 1 * - HW_I2C_F - I2C Frequency Divider register * - HW_I2C_C1 - I2C Control Register 1 * - HW_I2C_S - I2C Status register * - HW_I2C_D - I2C Data I/O register * - HW_I2C_C2 - I2C Control Register 2 * - HW_I2C_FLT - I2C Programmable Input Glitch Filter register * - HW_I2C_RA - I2C Range Address register * - HW_I2C_SMB - I2C SMBus Control and Status register * - HW_I2C_A2 - I2C Address Register 2 * - HW_I2C_SLTH - I2C SCL Low Timeout Register High * - HW_I2C_SLTL - I2C SCL Low Timeout Register Low * * - hw_i2c_t - Struct containing all module registers. */ //! @name Module base addresses //@{ #ifndef REGS_I2C_BASE #define HW_I2C_INSTANCE_COUNT (3U) //!< Number of instances of the I2C module. #define HW_I2C0 (0U) //!< Instance number for I2C0. #define HW_I2C1 (1U) //!< Instance number for I2C1. #define HW_I2C2 (2U) //!< Instance number for I2C2. #define REGS_I2C0_BASE (0x40066000U) //!< Base address for I2C0. #define REGS_I2C1_BASE (0x40067000U) //!< Base address for I2C1. #define REGS_I2C2_BASE (0x400E6000U) //!< Base address for I2C2. //! @brief Table of base addresses for I2C instances. static const uint32_t __g_regs_I2C_base_addresses[] = { REGS_I2C0_BASE, REGS_I2C1_BASE, REGS_I2C2_BASE, }; //! @brief Get the base address of I2C by instance number. //! @param x I2C instance number, from 0 through 2. #define REGS_I2C_BASE(x) (__g_regs_I2C_base_addresses[(x)]) //! @brief Get the instance number given a base address. //! @param b Base address for an instance of I2C. #define REGS_I2C_INSTANCE(b) ((b) == REGS_I2C0_BASE ? HW_I2C0 : (b) == REGS_I2C1_BASE ? HW_I2C1 : (b) == REGS_I2C2_BASE ? HW_I2C2 : 0) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_A1 - I2C Address Register 1 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_A1 - I2C Address Register 1 (RW) * * Reset value: 0x00U * * This register contains the slave address to be used by the I2C module. */ typedef union _hw_i2c_a1 { uint8_t U; struct _hw_i2c_a1_bitfields { uint8_t RESERVED0 : 1; //!< [0] uint8_t AD : 7; //!< [7:1] Address } B; } hw_i2c_a1_t; #endif /*! * @name Constants and macros for entire I2C_A1 register */ //@{ #define HW_I2C_A1_ADDR(x) (REGS_I2C_BASE(x) + 0x0U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_A1(x) (*(__IO hw_i2c_a1_t *) HW_I2C_A1_ADDR(x)) #define HW_I2C_A1_RD(x) (HW_I2C_A1(x).U) #define HW_I2C_A1_WR(x, v) (HW_I2C_A1(x).U = (v)) #define HW_I2C_A1_SET(x, v) (HW_I2C_A1_WR(x, HW_I2C_A1_RD(x) | (v))) #define HW_I2C_A1_CLR(x, v) (HW_I2C_A1_WR(x, HW_I2C_A1_RD(x) & ~(v))) #define HW_I2C_A1_TOG(x, v) (HW_I2C_A1_WR(x, HW_I2C_A1_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_A1 bitfields */ /*! * @name Register I2C_A1, field AD[7:1] (RW) * * Contains the primary slave address used by the I2C module when it is * addressed as a slave. This field is used in the 7-bit address scheme and the lower * seven bits in the 10-bit address scheme. */ //@{ #define BP_I2C_A1_AD (1U) //!< Bit position for I2C_A1_AD. #define BM_I2C_A1_AD (0xFEU) //!< Bit mask for I2C_A1_AD. #define BS_I2C_A1_AD (7U) //!< Bit field size in bits for I2C_A1_AD. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_A1_AD field. #define BR_I2C_A1_AD(x) (HW_I2C_A1(x).B.AD) #endif //! @brief Format value for bitfield I2C_A1_AD. #define BF_I2C_A1_AD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_A1_AD), uint8_t) & BM_I2C_A1_AD) #ifndef __LANGUAGE_ASM__ //! @brief Set the AD field to a new value. #define BW_I2C_A1_AD(x, v) (HW_I2C_A1_WR(x, (HW_I2C_A1_RD(x) & ~BM_I2C_A1_AD) | BF_I2C_A1_AD(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_F - I2C Frequency Divider register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_F - I2C Frequency Divider register (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_f { uint8_t U; struct _hw_i2c_f_bitfields { uint8_t ICR : 6; //!< [5:0] ClockRate uint8_t MULT : 2; //!< [7:6] Multiplier Factor } B; } hw_i2c_f_t; #endif /*! * @name Constants and macros for entire I2C_F register */ //@{ #define HW_I2C_F_ADDR(x) (REGS_I2C_BASE(x) + 0x1U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_F(x) (*(__IO hw_i2c_f_t *) HW_I2C_F_ADDR(x)) #define HW_I2C_F_RD(x) (HW_I2C_F(x).U) #define HW_I2C_F_WR(x, v) (HW_I2C_F(x).U = (v)) #define HW_I2C_F_SET(x, v) (HW_I2C_F_WR(x, HW_I2C_F_RD(x) | (v))) #define HW_I2C_F_CLR(x, v) (HW_I2C_F_WR(x, HW_I2C_F_RD(x) & ~(v))) #define HW_I2C_F_TOG(x, v) (HW_I2C_F_WR(x, HW_I2C_F_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_F bitfields */ /*! * @name Register I2C_F, field ICR[5:0] (RW) * * Prescales the I2C module clock for bit rate selection. This field and the * MULT field determine the I2C baud rate, the SDA hold time, the SCL start hold * time, and the SCL stop hold time. For a list of values corresponding to each ICR * setting, see I2C divider and hold values. The SCL divider multiplied by * multiplier factor (mul) determines the I2C baud rate. I2C baud rate = I2C module * clock speed (Hz)/(mul * SCL divider) The SDA hold time is the delay from the * falling edge of SCL (I2C clock) to the changing of SDA (I2C data). SDA hold time = * I2C module clock period (s) * mul * SDA hold value The SCL start hold time is * the delay from the falling edge of SDA (I2C data) while SCL is high (start * condition) to the falling edge of SCL (I2C clock). SCL start hold time = I2C * module clock period (s) * mul * SCL start hold value The SCL stop hold time is * the delay from the rising edge of SCL (I2C clock) to the rising edge of SDA (I2C * data) while SCL is high (stop condition). SCL stop hold time = I2C module * clock period (s) * mul * SCL stop hold value For example, if the I2C module clock * speed is 8 MHz, the following table shows the possible hold time values with * different ICR and MULT selections to achieve an I2C baud rate of 100 kbit/s. * MULT ICR Hold times (μs) SDA SCL Start SCL Stop 2h 00h 3.500 3.000 5.500 1h * 07h 2.500 4.000 5.250 1h 0Bh 2.250 4.000 5.250 0h 14h 2.125 4.250 5.125 0h 18h * 1.125 4.750 5.125 */ //@{ #define BP_I2C_F_ICR (0U) //!< Bit position for I2C_F_ICR. #define BM_I2C_F_ICR (0x3FU) //!< Bit mask for I2C_F_ICR. #define BS_I2C_F_ICR (6U) //!< Bit field size in bits for I2C_F_ICR. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_F_ICR field. #define BR_I2C_F_ICR(x) (HW_I2C_F(x).B.ICR) #endif //! @brief Format value for bitfield I2C_F_ICR. #define BF_I2C_F_ICR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_F_ICR), uint8_t) & BM_I2C_F_ICR) #ifndef __LANGUAGE_ASM__ //! @brief Set the ICR field to a new value. #define BW_I2C_F_ICR(x, v) (HW_I2C_F_WR(x, (HW_I2C_F_RD(x) & ~BM_I2C_F_ICR) | BF_I2C_F_ICR(v))) #endif //@} /*! * @name Register I2C_F, field MULT[7:6] (RW) * * Defines the multiplier factor (mul). This factor is used along with the SCL * divider to generate the I2C baud rate. * * Values: * - 00 - mul = 1 * - 01 - mul = 2 * - 10 - mul = 4 * - 11 - Reserved */ //@{ #define BP_I2C_F_MULT (6U) //!< Bit position for I2C_F_MULT. #define BM_I2C_F_MULT (0xC0U) //!< Bit mask for I2C_F_MULT. #define BS_I2C_F_MULT (2U) //!< Bit field size in bits for I2C_F_MULT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_F_MULT field. #define BR_I2C_F_MULT(x) (HW_I2C_F(x).B.MULT) #endif //! @brief Format value for bitfield I2C_F_MULT. #define BF_I2C_F_MULT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_F_MULT), uint8_t) & BM_I2C_F_MULT) #ifndef __LANGUAGE_ASM__ //! @brief Set the MULT field to a new value. #define BW_I2C_F_MULT(x, v) (HW_I2C_F_WR(x, (HW_I2C_F_RD(x) & ~BM_I2C_F_MULT) | BF_I2C_F_MULT(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_C1 - I2C Control Register 1 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_C1 - I2C Control Register 1 (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_c1 { uint8_t U; struct _hw_i2c_c1_bitfields { uint8_t DMAEN : 1; //!< [0] DMA Enable uint8_t WUEN : 1; //!< [1] Wakeup Enable uint8_t RSTA : 1; //!< [2] Repeat START uint8_t TXAK : 1; //!< [3] Transmit Acknowledge Enable uint8_t TX : 1; //!< [4] Transmit Mode Select uint8_t MST : 1; //!< [5] Master Mode Select uint8_t IICIE : 1; //!< [6] I2C Interrupt Enable uint8_t IICEN : 1; //!< [7] I2C Enable } B; } hw_i2c_c1_t; #endif /*! * @name Constants and macros for entire I2C_C1 register */ //@{ #define HW_I2C_C1_ADDR(x) (REGS_I2C_BASE(x) + 0x2U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_C1(x) (*(__IO hw_i2c_c1_t *) HW_I2C_C1_ADDR(x)) #define HW_I2C_C1_RD(x) (HW_I2C_C1(x).U) #define HW_I2C_C1_WR(x, v) (HW_I2C_C1(x).U = (v)) #define HW_I2C_C1_SET(x, v) (HW_I2C_C1_WR(x, HW_I2C_C1_RD(x) | (v))) #define HW_I2C_C1_CLR(x, v) (HW_I2C_C1_WR(x, HW_I2C_C1_RD(x) & ~(v))) #define HW_I2C_C1_TOG(x, v) (HW_I2C_C1_WR(x, HW_I2C_C1_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_C1 bitfields */ /*! * @name Register I2C_C1, field DMAEN[0] (RW) * * Enables or disables the DMA function. * * Values: * - 0 - All DMA signalling disabled. * - 1 - DMA transfer is enabled. While SMB[FACK] = 0, the following conditions * trigger the DMA request: a data byte is received, and either address or * data is transmitted. (ACK/NACK is automatic) the first byte received matches * the A1 register or is a general call address. If any address matching * occurs, S[IAAS] and S[TCF] are set. If the direction of transfer is known * from master to slave, then it is not required to check S[SRW]. With this * assumption, DMA can also be used in this case. In other cases, if the master * reads data from the slave, then it is required to rewrite the C1 register * operation. With this assumption, DMA cannot be used. When FACK = 1, an * address or a data byte is transmitted. */ //@{ #define BP_I2C_C1_DMAEN (0U) //!< Bit position for I2C_C1_DMAEN. #define BM_I2C_C1_DMAEN (0x01U) //!< Bit mask for I2C_C1_DMAEN. #define BS_I2C_C1_DMAEN (1U) //!< Bit field size in bits for I2C_C1_DMAEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_DMAEN field. #define BR_I2C_C1_DMAEN(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_DMAEN)) #endif //! @brief Format value for bitfield I2C_C1_DMAEN. #define BF_I2C_C1_DMAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_DMAEN), uint8_t) & BM_I2C_C1_DMAEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAEN field to a new value. #define BW_I2C_C1_DMAEN(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_DMAEN) = (v)) #endif //@} /*! * @name Register I2C_C1, field WUEN[1] (RW) * * The I2C module can wake the MCU from low power mode with no peripheral bus * running when slave address matching occurs. * * Values: * - 0 - Normal operation. No interrupt generated when address matching in low * power mode. * - 1 - Enables the wakeup function in low power mode. */ //@{ #define BP_I2C_C1_WUEN (1U) //!< Bit position for I2C_C1_WUEN. #define BM_I2C_C1_WUEN (0x02U) //!< Bit mask for I2C_C1_WUEN. #define BS_I2C_C1_WUEN (1U) //!< Bit field size in bits for I2C_C1_WUEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_WUEN field. #define BR_I2C_C1_WUEN(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_WUEN)) #endif //! @brief Format value for bitfield I2C_C1_WUEN. #define BF_I2C_C1_WUEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_WUEN), uint8_t) & BM_I2C_C1_WUEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the WUEN field to a new value. #define BW_I2C_C1_WUEN(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_WUEN) = (v)) #endif //@} /*! * @name Register I2C_C1, field RSTA[2] (WORZ) * * Writing 1 to this bit generates a repeated START condition provided it is the * current master. This bit will always be read as 0. Attempting a repeat at the * wrong time results in loss of arbitration. */ //@{ #define BP_I2C_C1_RSTA (2U) //!< Bit position for I2C_C1_RSTA. #define BM_I2C_C1_RSTA (0x04U) //!< Bit mask for I2C_C1_RSTA. #define BS_I2C_C1_RSTA (1U) //!< Bit field size in bits for I2C_C1_RSTA. //! @brief Format value for bitfield I2C_C1_RSTA. #define BF_I2C_C1_RSTA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_RSTA), uint8_t) & BM_I2C_C1_RSTA) #ifndef __LANGUAGE_ASM__ //! @brief Set the RSTA field to a new value. #define BW_I2C_C1_RSTA(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_RSTA) = (v)) #endif //@} /*! * @name Register I2C_C1, field TXAK[3] (RW) * * Specifies the value driven onto the SDA during data acknowledge cycles for * both master and slave receivers. The value of SMB[FACK] affects NACK/ACK * generation. SCL is held low until TXAK is written. * * Values: * - 0 - An acknowledge signal is sent to the bus on the following receiving * byte (if FACK is cleared) or the current receiving byte (if FACK is set). * - 1 - No acknowledge signal is sent to the bus on the following receiving * data byte (if FACK is cleared) or the current receiving data byte (if FACK is * set). */ //@{ #define BP_I2C_C1_TXAK (3U) //!< Bit position for I2C_C1_TXAK. #define BM_I2C_C1_TXAK (0x08U) //!< Bit mask for I2C_C1_TXAK. #define BS_I2C_C1_TXAK (1U) //!< Bit field size in bits for I2C_C1_TXAK. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_TXAK field. #define BR_I2C_C1_TXAK(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_TXAK)) #endif //! @brief Format value for bitfield I2C_C1_TXAK. #define BF_I2C_C1_TXAK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_TXAK), uint8_t) & BM_I2C_C1_TXAK) #ifndef __LANGUAGE_ASM__ //! @brief Set the TXAK field to a new value. #define BW_I2C_C1_TXAK(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_TXAK) = (v)) #endif //@} /*! * @name Register I2C_C1, field TX[4] (RW) * * Selects the direction of master and slave transfers. In master mode this bit * must be set according to the type of transfer required. Therefore, for address * cycles, this bit is always set. When addressed as a slave this bit must be * set by software according to the SRW bit in the status register. * * Values: * - 0 - Receive * - 1 - Transmit */ //@{ #define BP_I2C_C1_TX (4U) //!< Bit position for I2C_C1_TX. #define BM_I2C_C1_TX (0x10U) //!< Bit mask for I2C_C1_TX. #define BS_I2C_C1_TX (1U) //!< Bit field size in bits for I2C_C1_TX. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_TX field. #define BR_I2C_C1_TX(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_TX)) #endif //! @brief Format value for bitfield I2C_C1_TX. #define BF_I2C_C1_TX(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_TX), uint8_t) & BM_I2C_C1_TX) #ifndef __LANGUAGE_ASM__ //! @brief Set the TX field to a new value. #define BW_I2C_C1_TX(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_TX) = (v)) #endif //@} /*! * @name Register I2C_C1, field MST[5] (RW) * * When MST is changed from 0 to 1, a START signal is generated on the bus and * master mode is selected. When this bit changes from 1 to 0, a STOP signal is * generated and the mode of operation changes from master to slave. * * Values: * - 0 - Slave mode * - 1 - Master mode */ //@{ #define BP_I2C_C1_MST (5U) //!< Bit position for I2C_C1_MST. #define BM_I2C_C1_MST (0x20U) //!< Bit mask for I2C_C1_MST. #define BS_I2C_C1_MST (1U) //!< Bit field size in bits for I2C_C1_MST. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_MST field. #define BR_I2C_C1_MST(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_MST)) #endif //! @brief Format value for bitfield I2C_C1_MST. #define BF_I2C_C1_MST(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_MST), uint8_t) & BM_I2C_C1_MST) #ifndef __LANGUAGE_ASM__ //! @brief Set the MST field to a new value. #define BW_I2C_C1_MST(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_MST) = (v)) #endif //@} /*! * @name Register I2C_C1, field IICIE[6] (RW) * * Enables I2C interrupt requests. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_I2C_C1_IICIE (6U) //!< Bit position for I2C_C1_IICIE. #define BM_I2C_C1_IICIE (0x40U) //!< Bit mask for I2C_C1_IICIE. #define BS_I2C_C1_IICIE (1U) //!< Bit field size in bits for I2C_C1_IICIE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_IICIE field. #define BR_I2C_C1_IICIE(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_IICIE)) #endif //! @brief Format value for bitfield I2C_C1_IICIE. #define BF_I2C_C1_IICIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_IICIE), uint8_t) & BM_I2C_C1_IICIE) #ifndef __LANGUAGE_ASM__ //! @brief Set the IICIE field to a new value. #define BW_I2C_C1_IICIE(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_IICIE) = (v)) #endif //@} /*! * @name Register I2C_C1, field IICEN[7] (RW) * * Enables I2C module operation. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_I2C_C1_IICEN (7U) //!< Bit position for I2C_C1_IICEN. #define BM_I2C_C1_IICEN (0x80U) //!< Bit mask for I2C_C1_IICEN. #define BS_I2C_C1_IICEN (1U) //!< Bit field size in bits for I2C_C1_IICEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C1_IICEN field. #define BR_I2C_C1_IICEN(x) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_IICEN)) #endif //! @brief Format value for bitfield I2C_C1_IICEN. #define BF_I2C_C1_IICEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C1_IICEN), uint8_t) & BM_I2C_C1_IICEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the IICEN field to a new value. #define BW_I2C_C1_IICEN(x, v) (BITBAND_ACCESS8(HW_I2C_C1_ADDR(x), BP_I2C_C1_IICEN) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_S - I2C Status register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_S - I2C Status register (RW) * * Reset value: 0x80U */ typedef union _hw_i2c_s { uint8_t U; struct _hw_i2c_s_bitfields { uint8_t RXAK : 1; //!< [0] Receive Acknowledge uint8_t IICIF : 1; //!< [1] Interrupt Flag uint8_t SRW : 1; //!< [2] Slave Read/Write uint8_t RAM : 1; //!< [3] Range Address Match uint8_t ARBL : 1; //!< [4] Arbitration Lost uint8_t BUSY : 1; //!< [5] Bus Busy uint8_t IAAS : 1; //!< [6] Addressed As A Slave uint8_t TCF : 1; //!< [7] Transfer Complete Flag } B; } hw_i2c_s_t; #endif /*! * @name Constants and macros for entire I2C_S register */ //@{ #define HW_I2C_S_ADDR(x) (REGS_I2C_BASE(x) + 0x3U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_S(x) (*(__IO hw_i2c_s_t *) HW_I2C_S_ADDR(x)) #define HW_I2C_S_RD(x) (HW_I2C_S(x).U) #define HW_I2C_S_WR(x, v) (HW_I2C_S(x).U = (v)) #define HW_I2C_S_SET(x, v) (HW_I2C_S_WR(x, HW_I2C_S_RD(x) | (v))) #define HW_I2C_S_CLR(x, v) (HW_I2C_S_WR(x, HW_I2C_S_RD(x) & ~(v))) #define HW_I2C_S_TOG(x, v) (HW_I2C_S_WR(x, HW_I2C_S_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_S bitfields */ /*! * @name Register I2C_S, field RXAK[0] (RO) * * Values: * - 0 - Acknowledge signal was received after the completion of one byte of * data transmission on the bus * - 1 - No acknowledge signal detected */ //@{ #define BP_I2C_S_RXAK (0U) //!< Bit position for I2C_S_RXAK. #define BM_I2C_S_RXAK (0x01U) //!< Bit mask for I2C_S_RXAK. #define BS_I2C_S_RXAK (1U) //!< Bit field size in bits for I2C_S_RXAK. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_RXAK field. #define BR_I2C_S_RXAK(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_RXAK)) #endif //@} /*! * @name Register I2C_S, field IICIF[1] (W1C) * * This bit sets when an interrupt is pending. This bit must be cleared by * software by writing 1 to it, such as in the interrupt routine. One of the following * events can set this bit: One byte transfer, including ACK/NACK bit, completes * if FACK is 0. An ACK or NACK is sent on the bus by writing 0 or 1 to TXAK * after this bit is set in receive mode. One byte transfer, excluding ACK/NACK bit, * completes if FACK is 1. Match of slave address to calling address including * primary slave address, range slave address , alert response address, second * slave address, or general call address. Arbitration lost In SMBus mode, any * timeouts except SCL and SDA high timeouts I2C bus stop or start detection if the * SSIE bit in the Input Glitch Filter register is 1 To clear the I2C bus stop or * start detection interrupt: In the interrupt service routine, first clear the * STOPF or STARTF bit in the Input Glitch Filter register by writing 1 to it, and * then clear the IICIF bit. If this sequence is reversed, the IICIF bit is * asserted again. * * Values: * - 0 - No interrupt pending * - 1 - Interrupt pending */ //@{ #define BP_I2C_S_IICIF (1U) //!< Bit position for I2C_S_IICIF. #define BM_I2C_S_IICIF (0x02U) //!< Bit mask for I2C_S_IICIF. #define BS_I2C_S_IICIF (1U) //!< Bit field size in bits for I2C_S_IICIF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_IICIF field. #define BR_I2C_S_IICIF(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_IICIF)) #endif //! @brief Format value for bitfield I2C_S_IICIF. #define BF_I2C_S_IICIF(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_S_IICIF), uint8_t) & BM_I2C_S_IICIF) #ifndef __LANGUAGE_ASM__ //! @brief Set the IICIF field to a new value. #define BW_I2C_S_IICIF(x, v) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_IICIF) = (v)) #endif //@} /*! * @name Register I2C_S, field SRW[2] (RO) * * When addressed as a slave, SRW indicates the value of the R/W command bit of * the calling address sent to the master. * * Values: * - 0 - Slave receive, master writing to slave * - 1 - Slave transmit, master reading from slave */ //@{ #define BP_I2C_S_SRW (2U) //!< Bit position for I2C_S_SRW. #define BM_I2C_S_SRW (0x04U) //!< Bit mask for I2C_S_SRW. #define BS_I2C_S_SRW (1U) //!< Bit field size in bits for I2C_S_SRW. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_SRW field. #define BR_I2C_S_SRW(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_SRW)) #endif //@} /*! * @name Register I2C_S, field RAM[3] (RW) * * This bit is set to 1 by any of the following conditions, if I2C_C2[RMEN] = 1: * Any nonzero calling address is received that matches the address in the RA * register. The calling address is within the range of values of the A1 and RA * registers. For the RAM bit to be set to 1 correctly, C1[IICIE] must be set to 1. * Writing the C1 register with any value clears this bit to 0. * * Values: * - 0 - Not addressed * - 1 - Addressed as a slave */ //@{ #define BP_I2C_S_RAM (3U) //!< Bit position for I2C_S_RAM. #define BM_I2C_S_RAM (0x08U) //!< Bit mask for I2C_S_RAM. #define BS_I2C_S_RAM (1U) //!< Bit field size in bits for I2C_S_RAM. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_RAM field. #define BR_I2C_S_RAM(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_RAM)) #endif //! @brief Format value for bitfield I2C_S_RAM. #define BF_I2C_S_RAM(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_S_RAM), uint8_t) & BM_I2C_S_RAM) #ifndef __LANGUAGE_ASM__ //! @brief Set the RAM field to a new value. #define BW_I2C_S_RAM(x, v) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_RAM) = (v)) #endif //@} /*! * @name Register I2C_S, field ARBL[4] (W1C) * * This bit is set by hardware when the arbitration procedure is lost. The ARBL * bit must be cleared by software, by writing 1 to it. * * Values: * - 0 - Standard bus operation. * - 1 - Loss of arbitration. */ //@{ #define BP_I2C_S_ARBL (4U) //!< Bit position for I2C_S_ARBL. #define BM_I2C_S_ARBL (0x10U) //!< Bit mask for I2C_S_ARBL. #define BS_I2C_S_ARBL (1U) //!< Bit field size in bits for I2C_S_ARBL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_ARBL field. #define BR_I2C_S_ARBL(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_ARBL)) #endif //! @brief Format value for bitfield I2C_S_ARBL. #define BF_I2C_S_ARBL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_S_ARBL), uint8_t) & BM_I2C_S_ARBL) #ifndef __LANGUAGE_ASM__ //! @brief Set the ARBL field to a new value. #define BW_I2C_S_ARBL(x, v) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_ARBL) = (v)) #endif //@} /*! * @name Register I2C_S, field BUSY[5] (RO) * * Indicates the status of the bus regardless of slave or master mode. This bit * is set when a START signal is detected and cleared when a STOP signal is * detected. * * Values: * - 0 - Bus is idle * - 1 - Bus is busy */ //@{ #define BP_I2C_S_BUSY (5U) //!< Bit position for I2C_S_BUSY. #define BM_I2C_S_BUSY (0x20U) //!< Bit mask for I2C_S_BUSY. #define BS_I2C_S_BUSY (1U) //!< Bit field size in bits for I2C_S_BUSY. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_BUSY field. #define BR_I2C_S_BUSY(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_BUSY)) #endif //@} /*! * @name Register I2C_S, field IAAS[6] (RW) * * This bit is set by one of the following conditions: The calling address * matches the programmed primary slave address in the A1 register, or matches the * range address in the RA register (which must be set to a nonzero value and under * the condition I2C_C2[RMEN] = 1). C2[GCAEN] is set and a general call is * received. SMB[SIICAEN] is set and the calling address matches the second programmed * slave address. ALERTEN is set and an SMBus alert response address is received * RMEN is set and an address is received that is within the range between the * values of the A1 and RA registers. IAAS sets before the ACK bit. The CPU must * check the SRW bit and set TX/RX accordingly. Writing the C1 register with any * value clears this bit. * * Values: * - 0 - Not addressed * - 1 - Addressed as a slave */ //@{ #define BP_I2C_S_IAAS (6U) //!< Bit position for I2C_S_IAAS. #define BM_I2C_S_IAAS (0x40U) //!< Bit mask for I2C_S_IAAS. #define BS_I2C_S_IAAS (1U) //!< Bit field size in bits for I2C_S_IAAS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_IAAS field. #define BR_I2C_S_IAAS(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_IAAS)) #endif //! @brief Format value for bitfield I2C_S_IAAS. #define BF_I2C_S_IAAS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_S_IAAS), uint8_t) & BM_I2C_S_IAAS) #ifndef __LANGUAGE_ASM__ //! @brief Set the IAAS field to a new value. #define BW_I2C_S_IAAS(x, v) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_IAAS) = (v)) #endif //@} /*! * @name Register I2C_S, field TCF[7] (RO) * * Acknowledges a byte transfer; TCF sets on the completion of a byte transfer. * This bit is valid only during or immediately following a transfer to or from * the I2C module. TCF is cleared by reading the I2C data register in receive mode * or by writing to the I2C data register in transmit mode. * * Values: * - 0 - Transfer in progress * - 1 - Transfer complete */ //@{ #define BP_I2C_S_TCF (7U) //!< Bit position for I2C_S_TCF. #define BM_I2C_S_TCF (0x80U) //!< Bit mask for I2C_S_TCF. #define BS_I2C_S_TCF (1U) //!< Bit field size in bits for I2C_S_TCF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_S_TCF field. #define BR_I2C_S_TCF(x) (BITBAND_ACCESS8(HW_I2C_S_ADDR(x), BP_I2C_S_TCF)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_D - I2C Data I/O register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_D - I2C Data I/O register (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_d { uint8_t U; struct _hw_i2c_d_bitfields { uint8_t DATA : 8; //!< [7:0] Data } B; } hw_i2c_d_t; #endif /*! * @name Constants and macros for entire I2C_D register */ //@{ #define HW_I2C_D_ADDR(x) (REGS_I2C_BASE(x) + 0x4U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_D(x) (*(__IO hw_i2c_d_t *) HW_I2C_D_ADDR(x)) #define HW_I2C_D_RD(x) (HW_I2C_D(x).U) #define HW_I2C_D_WR(x, v) (HW_I2C_D(x).U = (v)) #define HW_I2C_D_SET(x, v) (HW_I2C_D_WR(x, HW_I2C_D_RD(x) | (v))) #define HW_I2C_D_CLR(x, v) (HW_I2C_D_WR(x, HW_I2C_D_RD(x) & ~(v))) #define HW_I2C_D_TOG(x, v) (HW_I2C_D_WR(x, HW_I2C_D_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_D bitfields */ /*! * @name Register I2C_D, field DATA[7:0] (RW) * * In master transmit mode, when data is written to this register, a data * transfer is initiated. The most significant bit is sent first. In master receive * mode, reading this register initiates receiving of the next byte of data. When * making the transition out of master receive mode, switch the I2C mode before * reading the Data register to prevent an inadvertent initiation of a master * receive data transfer. In slave mode, the same functions are available after an * address match occurs. The C1[TX] bit must correctly reflect the desired direction * of transfer in master and slave modes for the transmission to begin. For * example, if the I2C module is configured for master transmit but a master receive * is desired, reading the Data register does not initiate the receive. Reading * the Data register returns the last byte received while the I2C module is * configured in master receive or slave receive mode. The Data register does not * reflect every byte that is transmitted on the I2C bus, and neither can software * verify that a byte has been written to the Data register correctly by reading it * back. In master transmit mode, the first byte of data written to the Data * register following assertion of MST (start bit) or assertion of RSTA (repeated * start bit) is used for the address transfer and must consist of the calling * address (in bits 7-1) concatenated with the required R/W bit (in position bit 0). */ //@{ #define BP_I2C_D_DATA (0U) //!< Bit position for I2C_D_DATA. #define BM_I2C_D_DATA (0xFFU) //!< Bit mask for I2C_D_DATA. #define BS_I2C_D_DATA (8U) //!< Bit field size in bits for I2C_D_DATA. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_D_DATA field. #define BR_I2C_D_DATA(x) (HW_I2C_D(x).U) #endif //! @brief Format value for bitfield I2C_D_DATA. #define BF_I2C_D_DATA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_D_DATA), uint8_t) & BM_I2C_D_DATA) #ifndef __LANGUAGE_ASM__ //! @brief Set the DATA field to a new value. #define BW_I2C_D_DATA(x, v) (HW_I2C_D_WR(x, v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_C2 - I2C Control Register 2 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_C2 - I2C Control Register 2 (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_c2 { uint8_t U; struct _hw_i2c_c2_bitfields { uint8_t AD : 3; //!< [2:0] Slave Address uint8_t RMEN : 1; //!< [3] Range Address Matching Enable uint8_t SBRC : 1; //!< [4] Slave Baud Rate Control uint8_t HDRS : 1; //!< [5] High Drive Select uint8_t ADEXT : 1; //!< [6] Address Extension uint8_t GCAEN : 1; //!< [7] General Call Address Enable } B; } hw_i2c_c2_t; #endif /*! * @name Constants and macros for entire I2C_C2 register */ //@{ #define HW_I2C_C2_ADDR(x) (REGS_I2C_BASE(x) + 0x5U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_C2(x) (*(__IO hw_i2c_c2_t *) HW_I2C_C2_ADDR(x)) #define HW_I2C_C2_RD(x) (HW_I2C_C2(x).U) #define HW_I2C_C2_WR(x, v) (HW_I2C_C2(x).U = (v)) #define HW_I2C_C2_SET(x, v) (HW_I2C_C2_WR(x, HW_I2C_C2_RD(x) | (v))) #define HW_I2C_C2_CLR(x, v) (HW_I2C_C2_WR(x, HW_I2C_C2_RD(x) & ~(v))) #define HW_I2C_C2_TOG(x, v) (HW_I2C_C2_WR(x, HW_I2C_C2_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_C2 bitfields */ /*! * @name Register I2C_C2, field AD[2:0] (RW) * * Contains the upper three bits of the slave address in the 10-bit address * scheme. This field is valid only while the ADEXT bit is set. */ //@{ #define BP_I2C_C2_AD (0U) //!< Bit position for I2C_C2_AD. #define BM_I2C_C2_AD (0x07U) //!< Bit mask for I2C_C2_AD. #define BS_I2C_C2_AD (3U) //!< Bit field size in bits for I2C_C2_AD. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_AD field. #define BR_I2C_C2_AD(x) (HW_I2C_C2(x).B.AD) #endif //! @brief Format value for bitfield I2C_C2_AD. #define BF_I2C_C2_AD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_AD), uint8_t) & BM_I2C_C2_AD) #ifndef __LANGUAGE_ASM__ //! @brief Set the AD field to a new value. #define BW_I2C_C2_AD(x, v) (HW_I2C_C2_WR(x, (HW_I2C_C2_RD(x) & ~BM_I2C_C2_AD) | BF_I2C_C2_AD(v))) #endif //@} /*! * @name Register I2C_C2, field RMEN[3] (RW) * * This bit controls the slave address matching for addresses between the values * of the A1 and RA registers. When this bit is set, a slave address matching * occurs for any address greater than the value of the A1 register and less than * or equal to the value of the RA register. * * Values: * - 0 - Range mode disabled. No address matching occurs for an address within * the range of values of the A1 and RA registers. * - 1 - Range mode enabled. Address matching occurs when a slave receives an * address within the range of values of the A1 and RA registers. */ //@{ #define BP_I2C_C2_RMEN (3U) //!< Bit position for I2C_C2_RMEN. #define BM_I2C_C2_RMEN (0x08U) //!< Bit mask for I2C_C2_RMEN. #define BS_I2C_C2_RMEN (1U) //!< Bit field size in bits for I2C_C2_RMEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_RMEN field. #define BR_I2C_C2_RMEN(x) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_RMEN)) #endif //! @brief Format value for bitfield I2C_C2_RMEN. #define BF_I2C_C2_RMEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_RMEN), uint8_t) & BM_I2C_C2_RMEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the RMEN field to a new value. #define BW_I2C_C2_RMEN(x, v) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_RMEN) = (v)) #endif //@} /*! * @name Register I2C_C2, field SBRC[4] (RW) * * Enables independent slave mode baud rate at maximum frequency, which forces * clock stretching on SCL in very fast I2C modes. To a slave, an example of a * "very fast" mode is when the master transfers at 40 kbit/s but the slave can * capture the master's data at only 10 kbit/s. * * Values: * - 0 - The slave baud rate follows the master baud rate and clock stretching * may occur * - 1 - Slave baud rate is independent of the master baud rate */ //@{ #define BP_I2C_C2_SBRC (4U) //!< Bit position for I2C_C2_SBRC. #define BM_I2C_C2_SBRC (0x10U) //!< Bit mask for I2C_C2_SBRC. #define BS_I2C_C2_SBRC (1U) //!< Bit field size in bits for I2C_C2_SBRC. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_SBRC field. #define BR_I2C_C2_SBRC(x) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_SBRC)) #endif //! @brief Format value for bitfield I2C_C2_SBRC. #define BF_I2C_C2_SBRC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_SBRC), uint8_t) & BM_I2C_C2_SBRC) #ifndef __LANGUAGE_ASM__ //! @brief Set the SBRC field to a new value. #define BW_I2C_C2_SBRC(x, v) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_SBRC) = (v)) #endif //@} /*! * @name Register I2C_C2, field HDRS[5] (RW) * * Controls the drive capability of the I2C pads. * * Values: * - 0 - Normal drive mode * - 1 - High drive mode */ //@{ #define BP_I2C_C2_HDRS (5U) //!< Bit position for I2C_C2_HDRS. #define BM_I2C_C2_HDRS (0x20U) //!< Bit mask for I2C_C2_HDRS. #define BS_I2C_C2_HDRS (1U) //!< Bit field size in bits for I2C_C2_HDRS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_HDRS field. #define BR_I2C_C2_HDRS(x) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_HDRS)) #endif //! @brief Format value for bitfield I2C_C2_HDRS. #define BF_I2C_C2_HDRS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_HDRS), uint8_t) & BM_I2C_C2_HDRS) #ifndef __LANGUAGE_ASM__ //! @brief Set the HDRS field to a new value. #define BW_I2C_C2_HDRS(x, v) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_HDRS) = (v)) #endif //@} /*! * @name Register I2C_C2, field ADEXT[6] (RW) * * Controls the number of bits used for the slave address. * * Values: * - 0 - 7-bit address scheme * - 1 - 10-bit address scheme */ //@{ #define BP_I2C_C2_ADEXT (6U) //!< Bit position for I2C_C2_ADEXT. #define BM_I2C_C2_ADEXT (0x40U) //!< Bit mask for I2C_C2_ADEXT. #define BS_I2C_C2_ADEXT (1U) //!< Bit field size in bits for I2C_C2_ADEXT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_ADEXT field. #define BR_I2C_C2_ADEXT(x) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_ADEXT)) #endif //! @brief Format value for bitfield I2C_C2_ADEXT. #define BF_I2C_C2_ADEXT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_ADEXT), uint8_t) & BM_I2C_C2_ADEXT) #ifndef __LANGUAGE_ASM__ //! @brief Set the ADEXT field to a new value. #define BW_I2C_C2_ADEXT(x, v) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_ADEXT) = (v)) #endif //@} /*! * @name Register I2C_C2, field GCAEN[7] (RW) * * Enables general call address. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_I2C_C2_GCAEN (7U) //!< Bit position for I2C_C2_GCAEN. #define BM_I2C_C2_GCAEN (0x80U) //!< Bit mask for I2C_C2_GCAEN. #define BS_I2C_C2_GCAEN (1U) //!< Bit field size in bits for I2C_C2_GCAEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_C2_GCAEN field. #define BR_I2C_C2_GCAEN(x) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_GCAEN)) #endif //! @brief Format value for bitfield I2C_C2_GCAEN. #define BF_I2C_C2_GCAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_C2_GCAEN), uint8_t) & BM_I2C_C2_GCAEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the GCAEN field to a new value. #define BW_I2C_C2_GCAEN(x, v) (BITBAND_ACCESS8(HW_I2C_C2_ADDR(x), BP_I2C_C2_GCAEN) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_FLT - I2C Programmable Input Glitch Filter register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_FLT - I2C Programmable Input Glitch Filter register (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_flt { uint8_t U; struct _hw_i2c_flt_bitfields { uint8_t FLT : 4; //!< [3:0] I2C Programmable Filter Factor uint8_t STARTF : 1; //!< [4] I2C Bus Start Detect Flag uint8_t SSIE : 1; //!< [5] I2C Bus Stop or Start Interrupt Enable uint8_t STOPF : 1; //!< [6] I2C Bus Stop Detect Flag uint8_t SHEN : 1; //!< [7] Stop Hold Enable } B; } hw_i2c_flt_t; #endif /*! * @name Constants and macros for entire I2C_FLT register */ //@{ #define HW_I2C_FLT_ADDR(x) (REGS_I2C_BASE(x) + 0x6U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_FLT(x) (*(__IO hw_i2c_flt_t *) HW_I2C_FLT_ADDR(x)) #define HW_I2C_FLT_RD(x) (HW_I2C_FLT(x).U) #define HW_I2C_FLT_WR(x, v) (HW_I2C_FLT(x).U = (v)) #define HW_I2C_FLT_SET(x, v) (HW_I2C_FLT_WR(x, HW_I2C_FLT_RD(x) | (v))) #define HW_I2C_FLT_CLR(x, v) (HW_I2C_FLT_WR(x, HW_I2C_FLT_RD(x) & ~(v))) #define HW_I2C_FLT_TOG(x, v) (HW_I2C_FLT_WR(x, HW_I2C_FLT_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_FLT bitfields */ /*! * @name Register I2C_FLT, field FLT[3:0] (RW) * * Controls the width of the glitch, in terms of I2C module clock cycles, that * the filter must absorb. For any glitch whose size is less than or equal to this * width setting, the filter does not allow the glitch to pass. * * Values: * - 0 - No filter/bypass */ //@{ #define BP_I2C_FLT_FLT (0U) //!< Bit position for I2C_FLT_FLT. #define BM_I2C_FLT_FLT (0x0FU) //!< Bit mask for I2C_FLT_FLT. #define BS_I2C_FLT_FLT (4U) //!< Bit field size in bits for I2C_FLT_FLT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_FLT_FLT field. #define BR_I2C_FLT_FLT(x) (HW_I2C_FLT(x).B.FLT) #endif //! @brief Format value for bitfield I2C_FLT_FLT. #define BF_I2C_FLT_FLT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_FLT_FLT), uint8_t) & BM_I2C_FLT_FLT) #ifndef __LANGUAGE_ASM__ //! @brief Set the FLT field to a new value. #define BW_I2C_FLT_FLT(x, v) (HW_I2C_FLT_WR(x, (HW_I2C_FLT_RD(x) & ~BM_I2C_FLT_FLT) | BF_I2C_FLT_FLT(v))) #endif //@} /*! * @name Register I2C_FLT, field STARTF[4] (W1C) * * Hardware sets this bit when the I2C bus's start status is detected. The * STARTF bit must be cleared by writing 1 to it. * * Values: * - 0 - No start happens on I2C bus * - 1 - Start detected on I2C bus */ //@{ #define BP_I2C_FLT_STARTF (4U) //!< Bit position for I2C_FLT_STARTF. #define BM_I2C_FLT_STARTF (0x10U) //!< Bit mask for I2C_FLT_STARTF. #define BS_I2C_FLT_STARTF (1U) //!< Bit field size in bits for I2C_FLT_STARTF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_FLT_STARTF field. #define BR_I2C_FLT_STARTF(x) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_STARTF)) #endif //! @brief Format value for bitfield I2C_FLT_STARTF. #define BF_I2C_FLT_STARTF(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_FLT_STARTF), uint8_t) & BM_I2C_FLT_STARTF) #ifndef __LANGUAGE_ASM__ //! @brief Set the STARTF field to a new value. #define BW_I2C_FLT_STARTF(x, v) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_STARTF) = (v)) #endif //@} /*! * @name Register I2C_FLT, field SSIE[5] (RW) * * This bit enables the interrupt for I2C bus stop or start detection. To clear * the I2C bus stop or start detection interrupt: In the interrupt service * routine, first clear the STOPF or STARTF bit by writing 1 to it, and then clear the * IICIF bit in the status register. If this sequence is reversed, the IICIF bit * is asserted again. * * Values: * - 0 - Stop or start detection interrupt is disabled * - 1 - Stop or start detection interrupt is enabled */ //@{ #define BP_I2C_FLT_SSIE (5U) //!< Bit position for I2C_FLT_SSIE. #define BM_I2C_FLT_SSIE (0x20U) //!< Bit mask for I2C_FLT_SSIE. #define BS_I2C_FLT_SSIE (1U) //!< Bit field size in bits for I2C_FLT_SSIE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_FLT_SSIE field. #define BR_I2C_FLT_SSIE(x) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_SSIE)) #endif //! @brief Format value for bitfield I2C_FLT_SSIE. #define BF_I2C_FLT_SSIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_FLT_SSIE), uint8_t) & BM_I2C_FLT_SSIE) #ifndef __LANGUAGE_ASM__ //! @brief Set the SSIE field to a new value. #define BW_I2C_FLT_SSIE(x, v) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_SSIE) = (v)) #endif //@} /*! * @name Register I2C_FLT, field STOPF[6] (W1C) * * Hardware sets this bit when the I2C bus's stop status is detected. The STOPF * bit must be cleared by writing 1 to it. * * Values: * - 0 - No stop happens on I2C bus * - 1 - Stop detected on I2C bus */ //@{ #define BP_I2C_FLT_STOPF (6U) //!< Bit position for I2C_FLT_STOPF. #define BM_I2C_FLT_STOPF (0x40U) //!< Bit mask for I2C_FLT_STOPF. #define BS_I2C_FLT_STOPF (1U) //!< Bit field size in bits for I2C_FLT_STOPF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_FLT_STOPF field. #define BR_I2C_FLT_STOPF(x) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_STOPF)) #endif //! @brief Format value for bitfield I2C_FLT_STOPF. #define BF_I2C_FLT_STOPF(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_FLT_STOPF), uint8_t) & BM_I2C_FLT_STOPF) #ifndef __LANGUAGE_ASM__ //! @brief Set the STOPF field to a new value. #define BW_I2C_FLT_STOPF(x, v) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_STOPF) = (v)) #endif //@} /*! * @name Register I2C_FLT, field SHEN[7] (RW) * * Set this bit to hold off entry to stop mode when any data transmission or * reception is occurring. The following scenario explains the holdoff * functionality: The I2C module is configured for a basic transfer, and the SHEN bit is set * to 1. A transfer begins. The MCU signals the I2C module to enter stop mode. The * byte currently being transferred, including both address and data, completes * its transfer. The I2C slave or master acknowledges that the in-transfer byte * completed its transfer and acknowledges the request to enter stop mode. After * receiving the I2C module's acknowledgment of the request to enter stop mode, * the MCU determines whether to shut off the I2C module's clock. If the SHEN bit * is set to 1 and the I2C module is in an idle or disabled state when the MCU * signals to enter stop mode, the module immediately acknowledges the request to * enter stop mode. If SHEN is cleared to 0 and the overall data transmission or * reception that was suspended by stop mode entry was incomplete: To resume the * overall transmission or reception after the MCU exits stop mode, software must * reinitialize the transfer by resending the address of the slave. If the I2C * Control Register 1's IICIE bit was set to 1 before the MCU entered stop mode, * system software will receive the interrupt triggered by the I2C Status Register's * TCF bit after the MCU wakes from the stop mode. * * Values: * - 0 - Stop holdoff is disabled. The MCU's entry to stop mode is not gated. * - 1 - Stop holdoff is enabled. */ //@{ #define BP_I2C_FLT_SHEN (7U) //!< Bit position for I2C_FLT_SHEN. #define BM_I2C_FLT_SHEN (0x80U) //!< Bit mask for I2C_FLT_SHEN. #define BS_I2C_FLT_SHEN (1U) //!< Bit field size in bits for I2C_FLT_SHEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_FLT_SHEN field. #define BR_I2C_FLT_SHEN(x) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_SHEN)) #endif //! @brief Format value for bitfield I2C_FLT_SHEN. #define BF_I2C_FLT_SHEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_FLT_SHEN), uint8_t) & BM_I2C_FLT_SHEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the SHEN field to a new value. #define BW_I2C_FLT_SHEN(x, v) (BITBAND_ACCESS8(HW_I2C_FLT_ADDR(x), BP_I2C_FLT_SHEN) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_RA - I2C Range Address register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_RA - I2C Range Address register (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_ra { uint8_t U; struct _hw_i2c_ra_bitfields { uint8_t RESERVED0 : 1; //!< [0] uint8_t RAD : 7; //!< [7:1] Range Slave Address } B; } hw_i2c_ra_t; #endif /*! * @name Constants and macros for entire I2C_RA register */ //@{ #define HW_I2C_RA_ADDR(x) (REGS_I2C_BASE(x) + 0x7U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_RA(x) (*(__IO hw_i2c_ra_t *) HW_I2C_RA_ADDR(x)) #define HW_I2C_RA_RD(x) (HW_I2C_RA(x).U) #define HW_I2C_RA_WR(x, v) (HW_I2C_RA(x).U = (v)) #define HW_I2C_RA_SET(x, v) (HW_I2C_RA_WR(x, HW_I2C_RA_RD(x) | (v))) #define HW_I2C_RA_CLR(x, v) (HW_I2C_RA_WR(x, HW_I2C_RA_RD(x) & ~(v))) #define HW_I2C_RA_TOG(x, v) (HW_I2C_RA_WR(x, HW_I2C_RA_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_RA bitfields */ /*! * @name Register I2C_RA, field RAD[7:1] (RW) * * This field contains the slave address to be used by the I2C module. The field * is used in the 7-bit address scheme. If I2C_C2[RMEN] is set to 1, any nonzero * value write enables this register. This register value can be considered as a * maximum boundary in the range matching mode. */ //@{ #define BP_I2C_RA_RAD (1U) //!< Bit position for I2C_RA_RAD. #define BM_I2C_RA_RAD (0xFEU) //!< Bit mask for I2C_RA_RAD. #define BS_I2C_RA_RAD (7U) //!< Bit field size in bits for I2C_RA_RAD. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_RA_RAD field. #define BR_I2C_RA_RAD(x) (HW_I2C_RA(x).B.RAD) #endif //! @brief Format value for bitfield I2C_RA_RAD. #define BF_I2C_RA_RAD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_RA_RAD), uint8_t) & BM_I2C_RA_RAD) #ifndef __LANGUAGE_ASM__ //! @brief Set the RAD field to a new value. #define BW_I2C_RA_RAD(x, v) (HW_I2C_RA_WR(x, (HW_I2C_RA_RD(x) & ~BM_I2C_RA_RAD) | BF_I2C_RA_RAD(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_SMB - I2C SMBus Control and Status register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_SMB - I2C SMBus Control and Status register (RW) * * Reset value: 0x00U * * When the SCL and SDA signals are held high for a length of time greater than * the high timeout period, the SHTF1 flag sets. Before reaching this threshold, * while the system is detecting how long these signals are being held high, a * master assumes that the bus is free. However, the SHTF1 bit is set to 1 in the * bus transmission process with the idle bus state. When the TCKSEL bit is set, * there is no need to monitor the SHTF1 bit because the bus speed is too high to * match the protocol of SMBus. */ typedef union _hw_i2c_smb { uint8_t U; struct _hw_i2c_smb_bitfields { uint8_t SHTF2IE : 1; //!< [0] SHTF2 Interrupt Enable uint8_t SHTF2 : 1; //!< [1] SCL High Timeout Flag 2 uint8_t SHTF1 : 1; //!< [2] SCL High Timeout Flag 1 uint8_t SLTF : 1; //!< [3] SCL Low Timeout Flag uint8_t TCKSEL : 1; //!< [4] Timeout Counter Clock Select uint8_t SIICAEN : 1; //!< [5] Second I2C Address Enable uint8_t ALERTEN : 1; //!< [6] SMBus Alert Response Address Enable uint8_t FACK : 1; //!< [7] Fast NACK/ACK Enable } B; } hw_i2c_smb_t; #endif /*! * @name Constants and macros for entire I2C_SMB register */ //@{ #define HW_I2C_SMB_ADDR(x) (REGS_I2C_BASE(x) + 0x8U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_SMB(x) (*(__IO hw_i2c_smb_t *) HW_I2C_SMB_ADDR(x)) #define HW_I2C_SMB_RD(x) (HW_I2C_SMB(x).U) #define HW_I2C_SMB_WR(x, v) (HW_I2C_SMB(x).U = (v)) #define HW_I2C_SMB_SET(x, v) (HW_I2C_SMB_WR(x, HW_I2C_SMB_RD(x) | (v))) #define HW_I2C_SMB_CLR(x, v) (HW_I2C_SMB_WR(x, HW_I2C_SMB_RD(x) & ~(v))) #define HW_I2C_SMB_TOG(x, v) (HW_I2C_SMB_WR(x, HW_I2C_SMB_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_SMB bitfields */ /*! * @name Register I2C_SMB, field SHTF2IE[0] (RW) * * Enables SCL high and SDA low timeout interrupt. * * Values: * - 0 - SHTF2 interrupt is disabled * - 1 - SHTF2 interrupt is enabled */ //@{ #define BP_I2C_SMB_SHTF2IE (0U) //!< Bit position for I2C_SMB_SHTF2IE. #define BM_I2C_SMB_SHTF2IE (0x01U) //!< Bit mask for I2C_SMB_SHTF2IE. #define BS_I2C_SMB_SHTF2IE (1U) //!< Bit field size in bits for I2C_SMB_SHTF2IE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_SHTF2IE field. #define BR_I2C_SMB_SHTF2IE(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SHTF2IE)) #endif //! @brief Format value for bitfield I2C_SMB_SHTF2IE. #define BF_I2C_SMB_SHTF2IE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_SHTF2IE), uint8_t) & BM_I2C_SMB_SHTF2IE) #ifndef __LANGUAGE_ASM__ //! @brief Set the SHTF2IE field to a new value. #define BW_I2C_SMB_SHTF2IE(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SHTF2IE) = (v)) #endif //@} /*! * @name Register I2C_SMB, field SHTF2[1] (W1C) * * This bit sets when SCL is held high and SDA is held low more than clock * * LoValue / 512. Software clears this bit by writing 1 to it. * * Values: * - 0 - No SCL high and SDA low timeout occurs * - 1 - SCL high and SDA low timeout occurs */ //@{ #define BP_I2C_SMB_SHTF2 (1U) //!< Bit position for I2C_SMB_SHTF2. #define BM_I2C_SMB_SHTF2 (0x02U) //!< Bit mask for I2C_SMB_SHTF2. #define BS_I2C_SMB_SHTF2 (1U) //!< Bit field size in bits for I2C_SMB_SHTF2. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_SHTF2 field. #define BR_I2C_SMB_SHTF2(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SHTF2)) #endif //! @brief Format value for bitfield I2C_SMB_SHTF2. #define BF_I2C_SMB_SHTF2(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_SHTF2), uint8_t) & BM_I2C_SMB_SHTF2) #ifndef __LANGUAGE_ASM__ //! @brief Set the SHTF2 field to a new value. #define BW_I2C_SMB_SHTF2(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SHTF2) = (v)) #endif //@} /*! * @name Register I2C_SMB, field SHTF1[2] (RO) * * This read-only bit sets when SCL and SDA are held high more than clock * * LoValue / 512, which indicates the bus is free. This bit is cleared automatically. * * Values: * - 0 - No SCL high and SDA high timeout occurs * - 1 - SCL high and SDA high timeout occurs */ //@{ #define BP_I2C_SMB_SHTF1 (2U) //!< Bit position for I2C_SMB_SHTF1. #define BM_I2C_SMB_SHTF1 (0x04U) //!< Bit mask for I2C_SMB_SHTF1. #define BS_I2C_SMB_SHTF1 (1U) //!< Bit field size in bits for I2C_SMB_SHTF1. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_SHTF1 field. #define BR_I2C_SMB_SHTF1(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SHTF1)) #endif //@} /*! * @name Register I2C_SMB, field SLTF[3] (W1C) * * This bit is set when the SLT register (consisting of the SLTH and SLTL * registers) is loaded with a non-zero value (LoValue) and an SCL low timeout occurs. * Software clears this bit by writing a logic 1 to it. The low timeout function * is disabled when the SLT register's value is 0. * * Values: * - 0 - No low timeout occurs * - 1 - Low timeout occurs */ //@{ #define BP_I2C_SMB_SLTF (3U) //!< Bit position for I2C_SMB_SLTF. #define BM_I2C_SMB_SLTF (0x08U) //!< Bit mask for I2C_SMB_SLTF. #define BS_I2C_SMB_SLTF (1U) //!< Bit field size in bits for I2C_SMB_SLTF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_SLTF field. #define BR_I2C_SMB_SLTF(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SLTF)) #endif //! @brief Format value for bitfield I2C_SMB_SLTF. #define BF_I2C_SMB_SLTF(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_SLTF), uint8_t) & BM_I2C_SMB_SLTF) #ifndef __LANGUAGE_ASM__ //! @brief Set the SLTF field to a new value. #define BW_I2C_SMB_SLTF(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SLTF) = (v)) #endif //@} /*! * @name Register I2C_SMB, field TCKSEL[4] (RW) * * Selects the clock source of the timeout counter. * * Values: * - 0 - Timeout counter counts at the frequency of the I2C module clock / 64 * - 1 - Timeout counter counts at the frequency of the I2C module clock */ //@{ #define BP_I2C_SMB_TCKSEL (4U) //!< Bit position for I2C_SMB_TCKSEL. #define BM_I2C_SMB_TCKSEL (0x10U) //!< Bit mask for I2C_SMB_TCKSEL. #define BS_I2C_SMB_TCKSEL (1U) //!< Bit field size in bits for I2C_SMB_TCKSEL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_TCKSEL field. #define BR_I2C_SMB_TCKSEL(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_TCKSEL)) #endif //! @brief Format value for bitfield I2C_SMB_TCKSEL. #define BF_I2C_SMB_TCKSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_TCKSEL), uint8_t) & BM_I2C_SMB_TCKSEL) #ifndef __LANGUAGE_ASM__ //! @brief Set the TCKSEL field to a new value. #define BW_I2C_SMB_TCKSEL(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_TCKSEL) = (v)) #endif //@} /*! * @name Register I2C_SMB, field SIICAEN[5] (RW) * * Enables or disables SMBus device default address. * * Values: * - 0 - I2C address register 2 matching is disabled * - 1 - I2C address register 2 matching is enabled */ //@{ #define BP_I2C_SMB_SIICAEN (5U) //!< Bit position for I2C_SMB_SIICAEN. #define BM_I2C_SMB_SIICAEN (0x20U) //!< Bit mask for I2C_SMB_SIICAEN. #define BS_I2C_SMB_SIICAEN (1U) //!< Bit field size in bits for I2C_SMB_SIICAEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_SIICAEN field. #define BR_I2C_SMB_SIICAEN(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SIICAEN)) #endif //! @brief Format value for bitfield I2C_SMB_SIICAEN. #define BF_I2C_SMB_SIICAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_SIICAEN), uint8_t) & BM_I2C_SMB_SIICAEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the SIICAEN field to a new value. #define BW_I2C_SMB_SIICAEN(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_SIICAEN) = (v)) #endif //@} /*! * @name Register I2C_SMB, field ALERTEN[6] (RW) * * Enables or disables SMBus alert response address matching. After the host * responds to a device that used the alert response address, you must use software * to put the device's address on the bus. The alert protocol is described in the * SMBus specification. * * Values: * - 0 - SMBus alert response address matching is disabled * - 1 - SMBus alert response address matching is enabled */ //@{ #define BP_I2C_SMB_ALERTEN (6U) //!< Bit position for I2C_SMB_ALERTEN. #define BM_I2C_SMB_ALERTEN (0x40U) //!< Bit mask for I2C_SMB_ALERTEN. #define BS_I2C_SMB_ALERTEN (1U) //!< Bit field size in bits for I2C_SMB_ALERTEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_ALERTEN field. #define BR_I2C_SMB_ALERTEN(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_ALERTEN)) #endif //! @brief Format value for bitfield I2C_SMB_ALERTEN. #define BF_I2C_SMB_ALERTEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_ALERTEN), uint8_t) & BM_I2C_SMB_ALERTEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the ALERTEN field to a new value. #define BW_I2C_SMB_ALERTEN(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_ALERTEN) = (v)) #endif //@} /*! * @name Register I2C_SMB, field FACK[7] (RW) * * For SMBus packet error checking, the CPU must be able to issue an ACK or NACK * according to the result of receiving data byte. * * Values: * - 0 - An ACK or NACK is sent on the following receiving data byte * - 1 - Writing 0 to TXAK after receiving a data byte generates an ACK. Writing * 1 to TXAK after receiving a data byte generates a NACK. */ //@{ #define BP_I2C_SMB_FACK (7U) //!< Bit position for I2C_SMB_FACK. #define BM_I2C_SMB_FACK (0x80U) //!< Bit mask for I2C_SMB_FACK. #define BS_I2C_SMB_FACK (1U) //!< Bit field size in bits for I2C_SMB_FACK. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SMB_FACK field. #define BR_I2C_SMB_FACK(x) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_FACK)) #endif //! @brief Format value for bitfield I2C_SMB_FACK. #define BF_I2C_SMB_FACK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SMB_FACK), uint8_t) & BM_I2C_SMB_FACK) #ifndef __LANGUAGE_ASM__ //! @brief Set the FACK field to a new value. #define BW_I2C_SMB_FACK(x, v) (BITBAND_ACCESS8(HW_I2C_SMB_ADDR(x), BP_I2C_SMB_FACK) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_A2 - I2C Address Register 2 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_A2 - I2C Address Register 2 (RW) * * Reset value: 0xC2U */ typedef union _hw_i2c_a2 { uint8_t U; struct _hw_i2c_a2_bitfields { uint8_t RESERVED0 : 1; //!< [0] uint8_t SAD : 7; //!< [7:1] SMBus Address } B; } hw_i2c_a2_t; #endif /*! * @name Constants and macros for entire I2C_A2 register */ //@{ #define HW_I2C_A2_ADDR(x) (REGS_I2C_BASE(x) + 0x9U) #ifndef __LANGUAGE_ASM__ #define HW_I2C_A2(x) (*(__IO hw_i2c_a2_t *) HW_I2C_A2_ADDR(x)) #define HW_I2C_A2_RD(x) (HW_I2C_A2(x).U) #define HW_I2C_A2_WR(x, v) (HW_I2C_A2(x).U = (v)) #define HW_I2C_A2_SET(x, v) (HW_I2C_A2_WR(x, HW_I2C_A2_RD(x) | (v))) #define HW_I2C_A2_CLR(x, v) (HW_I2C_A2_WR(x, HW_I2C_A2_RD(x) & ~(v))) #define HW_I2C_A2_TOG(x, v) (HW_I2C_A2_WR(x, HW_I2C_A2_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_A2 bitfields */ /*! * @name Register I2C_A2, field SAD[7:1] (RW) * * Contains the slave address used by the SMBus. This field is used on the * device default address or other related addresses. */ //@{ #define BP_I2C_A2_SAD (1U) //!< Bit position for I2C_A2_SAD. #define BM_I2C_A2_SAD (0xFEU) //!< Bit mask for I2C_A2_SAD. #define BS_I2C_A2_SAD (7U) //!< Bit field size in bits for I2C_A2_SAD. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_A2_SAD field. #define BR_I2C_A2_SAD(x) (HW_I2C_A2(x).B.SAD) #endif //! @brief Format value for bitfield I2C_A2_SAD. #define BF_I2C_A2_SAD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_A2_SAD), uint8_t) & BM_I2C_A2_SAD) #ifndef __LANGUAGE_ASM__ //! @brief Set the SAD field to a new value. #define BW_I2C_A2_SAD(x, v) (HW_I2C_A2_WR(x, (HW_I2C_A2_RD(x) & ~BM_I2C_A2_SAD) | BF_I2C_A2_SAD(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_SLTH - I2C SCL Low Timeout Register High //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_SLTH - I2C SCL Low Timeout Register High (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_slth { uint8_t U; struct _hw_i2c_slth_bitfields { uint8_t SSLT : 8; //!< [7:0] } B; } hw_i2c_slth_t; #endif /*! * @name Constants and macros for entire I2C_SLTH register */ //@{ #define HW_I2C_SLTH_ADDR(x) (REGS_I2C_BASE(x) + 0xAU) #ifndef __LANGUAGE_ASM__ #define HW_I2C_SLTH(x) (*(__IO hw_i2c_slth_t *) HW_I2C_SLTH_ADDR(x)) #define HW_I2C_SLTH_RD(x) (HW_I2C_SLTH(x).U) #define HW_I2C_SLTH_WR(x, v) (HW_I2C_SLTH(x).U = (v)) #define HW_I2C_SLTH_SET(x, v) (HW_I2C_SLTH_WR(x, HW_I2C_SLTH_RD(x) | (v))) #define HW_I2C_SLTH_CLR(x, v) (HW_I2C_SLTH_WR(x, HW_I2C_SLTH_RD(x) & ~(v))) #define HW_I2C_SLTH_TOG(x, v) (HW_I2C_SLTH_WR(x, HW_I2C_SLTH_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_SLTH bitfields */ /*! * @name Register I2C_SLTH, field SSLT[7:0] (RW) * * Most significant byte of SCL low timeout value that determines the timeout * period of SCL low. */ //@{ #define BP_I2C_SLTH_SSLT (0U) //!< Bit position for I2C_SLTH_SSLT. #define BM_I2C_SLTH_SSLT (0xFFU) //!< Bit mask for I2C_SLTH_SSLT. #define BS_I2C_SLTH_SSLT (8U) //!< Bit field size in bits for I2C_SLTH_SSLT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SLTH_SSLT field. #define BR_I2C_SLTH_SSLT(x) (HW_I2C_SLTH(x).U) #endif //! @brief Format value for bitfield I2C_SLTH_SSLT. #define BF_I2C_SLTH_SSLT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SLTH_SSLT), uint8_t) & BM_I2C_SLTH_SSLT) #ifndef __LANGUAGE_ASM__ //! @brief Set the SSLT field to a new value. #define BW_I2C_SLTH_SSLT(x, v) (HW_I2C_SLTH_WR(x, v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_I2C_SLTL - I2C SCL Low Timeout Register Low //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_I2C_SLTL - I2C SCL Low Timeout Register Low (RW) * * Reset value: 0x00U */ typedef union _hw_i2c_sltl { uint8_t U; struct _hw_i2c_sltl_bitfields { uint8_t SSLT : 8; //!< [7:0] } B; } hw_i2c_sltl_t; #endif /*! * @name Constants and macros for entire I2C_SLTL register */ //@{ #define HW_I2C_SLTL_ADDR(x) (REGS_I2C_BASE(x) + 0xBU) #ifndef __LANGUAGE_ASM__ #define HW_I2C_SLTL(x) (*(__IO hw_i2c_sltl_t *) HW_I2C_SLTL_ADDR(x)) #define HW_I2C_SLTL_RD(x) (HW_I2C_SLTL(x).U) #define HW_I2C_SLTL_WR(x, v) (HW_I2C_SLTL(x).U = (v)) #define HW_I2C_SLTL_SET(x, v) (HW_I2C_SLTL_WR(x, HW_I2C_SLTL_RD(x) | (v))) #define HW_I2C_SLTL_CLR(x, v) (HW_I2C_SLTL_WR(x, HW_I2C_SLTL_RD(x) & ~(v))) #define HW_I2C_SLTL_TOG(x, v) (HW_I2C_SLTL_WR(x, HW_I2C_SLTL_RD(x) ^ (v))) #endif //@} /* * Constants & macros for individual I2C_SLTL bitfields */ /*! * @name Register I2C_SLTL, field SSLT[7:0] (RW) * * Least significant byte of SCL low timeout value that determines the timeout * period of SCL low. */ //@{ #define BP_I2C_SLTL_SSLT (0U) //!< Bit position for I2C_SLTL_SSLT. #define BM_I2C_SLTL_SSLT (0xFFU) //!< Bit mask for I2C_SLTL_SSLT. #define BS_I2C_SLTL_SSLT (8U) //!< Bit field size in bits for I2C_SLTL_SSLT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the I2C_SLTL_SSLT field. #define BR_I2C_SLTL_SSLT(x) (HW_I2C_SLTL(x).U) #endif //! @brief Format value for bitfield I2C_SLTL_SSLT. #define BF_I2C_SLTL_SSLT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint8_t) << BP_I2C_SLTL_SSLT), uint8_t) & BM_I2C_SLTL_SSLT) #ifndef __LANGUAGE_ASM__ //! @brief Set the SSLT field to a new value. #define BW_I2C_SLTL_SSLT(x, v) (HW_I2C_SLTL_WR(x, v)) #endif //@} //------------------------------------------------------------------------------------------- // hw_i2c_t - module struct //------------------------------------------------------------------------------------------- /*! * @brief All I2C module registers. */ #ifndef __LANGUAGE_ASM__ #pragma pack(1) typedef struct _hw_i2c { __IO hw_i2c_a1_t A1; //!< [0x0] I2C Address Register 1 __IO hw_i2c_f_t F; //!< [0x1] I2C Frequency Divider register __IO hw_i2c_c1_t C1; //!< [0x2] I2C Control Register 1 __IO hw_i2c_s_t S; //!< [0x3] I2C Status register __IO hw_i2c_d_t D; //!< [0x4] I2C Data I/O register __IO hw_i2c_c2_t C2; //!< [0x5] I2C Control Register 2 __IO hw_i2c_flt_t FLT; //!< [0x6] I2C Programmable Input Glitch Filter register __IO hw_i2c_ra_t RA; //!< [0x7] I2C Range Address register __IO hw_i2c_smb_t SMB; //!< [0x8] I2C SMBus Control and Status register __IO hw_i2c_a2_t A2; //!< [0x9] I2C Address Register 2 __IO hw_i2c_slth_t SLTH; //!< [0xA] I2C SCL Low Timeout Register High __IO hw_i2c_sltl_t SLTL; //!< [0xB] I2C SCL Low Timeout Register Low } hw_i2c_t; #pragma pack() //! @brief Macro to access all I2C registers. //! @param x I2C instance number. //! @return Reference (not a pointer) to the registers struct. To get a pointer to the struct, //! use the '&' operator, like <code>&HW_I2C(0)</code>. #define HW_I2C(x) (*(hw_i2c_t *) REGS_I2C_BASE(x)) #endif #endif // __HW_I2C_REGISTERS_H__ // v22/130726/0.9 // EOF