mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_i2c_ex.c
- Committer:
- shaoziyang
- Date:
- 2014-09-13
- Revision:
- 323:9e901b0a5aa1
- Parent:
- 218:44081b78fdc2
File content as of revision 323:9e901b0a5aa1:
/** ****************************************************************************** * @file stm32f0xx_hal_i2c_ex.c * @author MCD Application Team * @version V1.0.0 * @date 28-May-2014 * @brief I2C Extension HAL module driver. * This file provides firmware functions to manage the following * functionalities of I2C extension peripheral: * + Extension features functions * @verbatim ============================================================================== ##### I2C peripheral extension features ##### ============================================================================== [..] Comparing to other previous devices, the I2C interface for STM32F0XX devices contains the following additional features (+) Possibility to disable or enable Analog Noise Filter (+) Use of a configured Digital Noise Filter (+) Disable or enable wakeup from Stop mode ##### How to use this driver ##### ============================================================================== [..] This driver provides functions to configure Noise Filter (#) Configure I2C Analog noise filter using the function HAL_I2CEx_AnalogFilter_Config() (#) Configure I2C Digital noise filter using the function HAL_I2CEx_DigitalFilter_Config() (#) Configure the enabling or disabling of I2C Wake Up Mode using the functions : + HAL_I2CEx_EnableWakeUp() + HAL_I2CEx_DisableWakeUp() @endverbatim ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32f0xx_hal.h" /** @addtogroup STM32F0xx_HAL_Driver * @{ */ /** @defgroup I2CEx * @brief I2C Extended HAL module driver * @{ */ #ifdef HAL_I2C_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /* Private functions ---------------------------------------------------------*/ /** @defgroup I2CEx_Private_Functions * @{ */ /** @defgroup I2CEx_Group1 Extended features functions * @brief Extended features functions * @verbatim =============================================================================== ##### Extension features functions ##### =============================================================================== [..] This section provides functions allowing to: (+) Configure Noise Filters @endverbatim * @{ */ /** * @brief Configures I2C Analog noise filter. * @param hi2c : pointer to a I2C_HandleTypeDef structure that contains * the configuration information for the specified I2Cx peripheral. * @param AnalogFilter : new state of the Analog filter. * @retval HAL status */ HAL_StatusTypeDef HAL_I2CEx_AnalogFilter_Config(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter) { /* Check the parameters */ assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); assert_param(IS_I2C_ANALOG_FILTER(AnalogFilter)); if((hi2c->State == HAL_I2C_STATE_BUSY) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_RX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_RX)) { return HAL_BUSY; } /* Process Locked */ __HAL_LOCK(hi2c); hi2c->State = HAL_I2C_STATE_BUSY; /* Disable the selected I2C peripheral */ __HAL_I2C_DISABLE(hi2c); /* Reset I2Cx ANOFF bit */ hi2c->Instance->CR1 &= ~(I2C_CR1_ANFOFF); /* Set analog filter bit*/ hi2c->Instance->CR1 |= AnalogFilter; __HAL_I2C_ENABLE(hi2c); hi2c->State = HAL_I2C_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hi2c); return HAL_OK; } /** * @brief Configures I2C Digital noise filter. * @param hi2c : pointer to a I2C_HandleTypeDef structure that contains * the configuration information for the specified I2Cx peripheral. * @param DigitalFilter : Coefficient of digital noise filter between 0x00 and 0x0F. * @retval HAL status */ HAL_StatusTypeDef HAL_I2CEx_DigitalFilter_Config(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); assert_param(IS_I2C_DIGITAL_FILTER(DigitalFilter)); if((hi2c->State == HAL_I2C_STATE_BUSY) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_RX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_RX)) { return HAL_BUSY; } /* Process Locked */ __HAL_LOCK(hi2c); hi2c->State = HAL_I2C_STATE_BUSY; /* Disable the selected I2C peripheral */ __HAL_I2C_DISABLE(hi2c); /* Get the old register value */ tmpreg = hi2c->Instance->CR1; /* Reset I2Cx DNF bits [11:8] */ tmpreg &= ~(I2C_CR1_DFN); /* Set I2Cx DNF coefficient */ tmpreg |= DigitalFilter << 8; /* Store the new register value */ hi2c->Instance->CR1 = tmpreg; __HAL_I2C_ENABLE(hi2c); hi2c->State = HAL_I2C_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hi2c); return HAL_OK; } /** * @brief Enables I2C wakeup from stop mode. * @param hi2c : pointer to a I2C_HandleTypeDef structure that contains * the configuration information for the specified I2Cx peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp (I2C_HandleTypeDef *hi2c) { /* Check the parameters */ assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); if((hi2c->State == HAL_I2C_STATE_BUSY) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_RX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_RX)) { return HAL_BUSY; } /* Process Locked */ __HAL_LOCK(hi2c); hi2c->State = HAL_I2C_STATE_BUSY; /* Disable the selected I2C peripheral */ __HAL_I2C_DISABLE(hi2c); /* Enable wakeup from stop mode */ hi2c->Instance->CR1 |= I2C_CR1_WUPEN; __HAL_I2C_ENABLE(hi2c); hi2c->State = HAL_I2C_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hi2c); return HAL_OK; } /** * @brief Disables I2C wakeup from stop mode. * @param hi2c : pointer to a I2C_HandleTypeDef structure that contains * the configuration information for the specified I2Cx peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp (I2C_HandleTypeDef *hi2c) { /* Check the parameters */ assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); if((hi2c->State == HAL_I2C_STATE_BUSY) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_MASTER_BUSY_RX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_TX) || (hi2c->State == HAL_I2C_STATE_SLAVE_BUSY_RX)) { return HAL_BUSY; } /* Process Locked */ __HAL_LOCK(hi2c); hi2c->State = HAL_I2C_STATE_BUSY; /* Disable the selected I2C peripheral */ __HAL_I2C_DISABLE(hi2c); /* Enable wakeup from stop mode */ hi2c->Instance->CR1 &= ~(I2C_CR1_WUPEN); __HAL_I2C_ENABLE(hi2c); hi2c->State = HAL_I2C_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hi2c); return HAL_OK; } /** * @} */ /** * @} */ #endif /* HAL_I2C_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/