mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
targets/hal/TARGET_STM/TARGET_NUCLEO_L152RE/i2c_api.c
- Committer:
- mbed_official
- Date:
- 2014-01-30
- Revision:
- 80:66393a7b209d
- Parent:
- 76:aeb1df146756
- Child:
- 118:b44c45162f28
File content as of revision 80:66393a7b209d:
/* mbed Microcontroller Library ******************************************************************************* * Copyright (c) 2014, STMicroelectronics * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ******************************************************************************* */ #include "i2c_api.h" #if DEVICE_I2C #include "cmsis.h" #include "pinmap.h" #include "error.h" /* Timeout values for flags and events waiting loops. These timeouts are not based on accurate values, they just guarantee that the application will not remain stuck if the I2C communication is corrupted. */ #define FLAG_TIMEOUT ((int)0x1000) #define LONG_TIMEOUT ((int)0x8000) static const PinMap PinMap_I2C_SDA[] = { {PB_9, I2C_1, STM_PIN_DATA(GPIO_Mode_AF, GPIO_OType_OD, GPIO_PuPd_UP, GPIO_AF_I2C1)}, {NC, NC, 0} }; static const PinMap PinMap_I2C_SCL[] = { {PB_8, I2C_1, STM_PIN_DATA(GPIO_Mode_AF, GPIO_OType_OD, GPIO_PuPd_UP, GPIO_AF_I2C1)}, {NC, NC, 0} }; void i2c_init(i2c_t *obj, PinName sda, PinName scl) { // Determine the I2C to use I2CName i2c_sda = (I2CName)pinmap_peripheral(sda, PinMap_I2C_SDA); I2CName i2c_scl = (I2CName)pinmap_peripheral(scl, PinMap_I2C_SCL); obj->i2c = (I2CName)pinmap_merge(i2c_sda, i2c_scl); if (obj->i2c == (I2CName)NC) { error("I2C pin mapping failed"); } // Enable I2C clock if (obj->i2c == I2C_1) { RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE); } if (obj->i2c == I2C_2) { RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE); } // Configure I2C pins pinmap_pinout(scl, PinMap_I2C_SCL); pin_mode(scl, OpenDrain); pinmap_pinout(sda, PinMap_I2C_SDA); pin_mode(sda, OpenDrain); // Reset to clear pending flags if any i2c_reset(obj); // I2C configuration i2c_frequency(obj, 100000); // 100 kHz per default } void i2c_frequency(i2c_t *obj, int hz) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); I2C_InitTypeDef I2C_InitStructure; if ((hz != 0) && (hz <= 400000)) { I2C_DeInit(i2c); // I2C configuration I2C_InitStructure.I2C_Mode = I2C_Mode_I2C; I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2; I2C_InitStructure.I2C_OwnAddress1 = 0; I2C_InitStructure.I2C_Ack = I2C_Ack_Enable; I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit; I2C_InitStructure.I2C_ClockSpeed = hz; I2C_Init(i2c, &I2C_InitStructure); I2C_Cmd(i2c, ENABLE); } } inline int i2c_start(i2c_t *obj) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); int timeout; I2C_ClearFlag(i2c, I2C_FLAG_AF); // Clear Acknowledge failure flag // Generate the START condition I2C_GenerateSTART(i2c, ENABLE); // Wait the START condition has been correctly sent timeout = FLAG_TIMEOUT; //while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_MODE_SELECT) == ERROR) { while (I2C_GetFlagStatus(i2c, I2C_FLAG_SB) == RESET) { timeout--; if (timeout == 0) { return 1; } } return 0; } inline int i2c_stop(i2c_t *obj) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); I2C_GenerateSTOP(i2c, ENABLE); return 0; } int i2c_read(i2c_t *obj, int address, char *data, int length, int stop) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); int timeout; int count; int value; if (length == 0) return 0; /* // Wait until the bus is not busy anymore timeout = LONG_TIMEOUT; while (I2C_GetFlagStatus(i2c, I2C_FLAG_BUSY) == SET) { timeout--; if (timeout == 0) { return 0; } } */ i2c_start(obj); // Send slave address for read I2C_Send7bitAddress(i2c, address, I2C_Direction_Receiver); // Wait address is acknowledged timeout = FLAG_TIMEOUT; while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED) == ERROR) { timeout--; if (timeout == 0) { return 0; } } // Read all bytes except last one for (count = 0; count < (length - 1); count++) { value = i2c_byte_read(obj, 0); data[count] = (char)value; } // If not repeated start, send stop. // Warning: must be done BEFORE the data is read. if (stop) { i2c_stop(obj); } // Read the last byte value = i2c_byte_read(obj, 1); data[count] = (char)value; return length; } int i2c_write(i2c_t *obj, int address, const char *data, int length, int stop) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); int timeout; int count; /* // Wait until the bus is not busy anymore timeout = LONG_TIMEOUT; while (I2C_GetFlagStatus(i2c, I2C_FLAG_BUSY) == SET) { timeout--; if (timeout == 0) { return 0; } } */ i2c_start(obj); // Send slave address for write I2C_Send7bitAddress(i2c, address, I2C_Direction_Transmitter); // Wait address is acknowledged timeout = FLAG_TIMEOUT; while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED) == ERROR) { timeout--; if (timeout == 0) { return 0; } } for (count = 0; count < length; count++) { if (i2c_byte_write(obj, data[count]) != 1) { i2c_stop(obj); return 0; } } // If not repeated start, send stop. if (stop) { i2c_stop(obj); } return count; } int i2c_byte_read(i2c_t *obj, int last) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); uint8_t data; int timeout; if (last) { // Don't acknowledge the last byte I2C_AcknowledgeConfig(i2c, DISABLE); } else { // Acknowledge the byte I2C_AcknowledgeConfig(i2c, ENABLE); } // Wait until the byte is received timeout = FLAG_TIMEOUT; while (I2C_GetFlagStatus(i2c, I2C_FLAG_RXNE) == RESET) { timeout--; if (timeout == 0) { return 0; } } data = I2C_ReceiveData(i2c); return (int)data; } int i2c_byte_write(i2c_t *obj, int data) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); int timeout; I2C_SendData(i2c, (uint8_t)data); // Wait until the byte is transmitted timeout = FLAG_TIMEOUT; //while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_BYTE_TRANSMITTED) == ERROR) { while ((I2C_GetFlagStatus(i2c, I2C_FLAG_TXE) == RESET) && (I2C_GetFlagStatus(i2c, I2C_FLAG_BTF) == RESET)) { timeout--; if (timeout == 0) { return 0; } } return 1; } void i2c_reset(i2c_t *obj) { if (obj->i2c == I2C_1) { RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, ENABLE); RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, DISABLE); } if (obj->i2c == I2C_2) { RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, ENABLE); RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, DISABLE); } } #if DEVICE_I2CSLAVE void i2c_slave_address(i2c_t *obj, int idx, uint32_t address, uint32_t mask) { I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c); uint16_t tmpreg; // Get the old register value tmpreg = i2c->OAR1; // Reset address bits tmpreg &= 0xFC00; // Set new address tmpreg |= (uint16_t)((uint16_t)address & (uint16_t)0x00FE); // 7-bits // Store the new register value i2c->OAR1 = tmpreg; } void i2c_slave_mode(i2c_t *obj, int enable_slave) { // Nothing to do } // See I2CSlave.h #define NoData 0 // the slave has not been addressed #define ReadAddressed 1 // the master has requested a read from this slave (slave = transmitter) #define WriteGeneral 2 // the master is writing to all slave #define WriteAddressed 3 // the master is writing to this slave (slave = receiver) int i2c_slave_receive(i2c_t *obj) { // TO BE DONE return(0); } int i2c_slave_read(i2c_t *obj, char *data, int length) { int count = 0; // Read all bytes for (count = 0; count < length; count++) { data[count] = i2c_byte_read(obj, 0); } return count; } int i2c_slave_write(i2c_t *obj, const char *data, int length) { int count = 0; // Write all bytes for (count = 0; count < length; count++) { i2c_byte_write(obj, data[count]); } return count; } #endif // DEVICE_I2CSLAVE #endif // DEVICE_I2C