mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_conf.h
- Committer:
- mbed_official
- Date:
- 2014-05-30
- Revision:
- 218:44081b78fdc2
- Parent:
- 205:c41fc65bcfb4
File content as of revision 218:44081b78fdc2:
/** ****************************************************************************** * @file stm32f0xx_hal_conf.h * @author MCD Application Team * @version V1.0.0 * @date 28-May-2014 * @brief HAL configuration file. ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32F0xx_HAL_CONF_H #define __STM32F0xx_HAL_CONF_H #ifdef __cplusplus extern "C" { #endif /* Exported types ------------------------------------------------------------*/ /* Exported constants --------------------------------------------------------*/ /* ########################## Module Selection ############################## */ /** * @brief This is the list of modules to be used in the HAL driver */ #define HAL_MODULE_ENABLED #define HAL_ADC_MODULE_ENABLED #define HAL_CAN_MODULE_ENABLED #define HAL_CEC_MODULE_ENABLED #define HAL_COMP_MODULE_ENABLED #define HAL_CORTEX_MODULE_ENABLED #define HAL_CRC_MODULE_ENABLED #define HAL_DAC_MODULE_ENABLED #define HAL_DMA_MODULE_ENABLED #define HAL_FLASH_MODULE_ENABLED #define HAL_GPIO_MODULE_ENABLED #define HAL_I2C_MODULE_ENABLED #define HAL_I2S_MODULE_ENABLED #define HAL_IRDA_MODULE_ENABLED #define HAL_IWDG_MODULE_ENABLED #define HAL_PCD_MODULE_ENABLED #define HAL_PWR_MODULE_ENABLED #define HAL_RCC_MODULE_ENABLED #define HAL_RTC_MODULE_ENABLED #define HAL_SMARTCARD_MODULE_ENABLED #define HAL_SMBUS_MODULE_ENABLED #define HAL_SPI_MODULE_ENABLED #define HAL_TIM_MODULE_ENABLED #define HAL_TSC_MODULE_ENABLED #define HAL_UART_MODULE_ENABLED #define HAL_USART_MODULE_ENABLED #define HAL_WWDG_MODULE_ENABLED /* ######################### Oscillator Values adaptation ################### */ /** * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. * This value is used by the RCC HAL module to compute the system frequency * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ /** * @brief In the following line adjust the External High Speed oscillator (HSE) Startup * Timeout value */ #if !defined (HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief Internal High Speed oscillator (HSI) value. * This value is used by the RCC HAL module to compute the system frequency * (when HSI is used as system clock source, directly or through the PLL). */ #if !defined (HSI_VALUE) #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup * Timeout value */ #if !defined (HSI_STARTUP_TIMEOUT) #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */ #endif /* HSI_STARTUP_TIMEOUT */ /** * @brief Internal High Speed oscillator for ADC (HSI14) value. */ #if !defined (HSI14_VALUE) #define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz. The real value may vary depending on the variations in voltage and temperature. */ #endif /* HSI14_VALUE */ /** * @brief Internal High Speed oscillator for USB (HSI48) value. */ #if !defined (HSI48_VALUE) #define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz. The real value may vary depending on the variations in voltage and temperature. */ #endif /* HSI48_VALUE */ /** * @brief Internal Low Speed oscillator (LSI) value. */ #if !defined (LSI_VALUE) #define LSI_VALUE ((uint32_t)40000) #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. */ /** * @brief External Low Speed oscillator (LSI) value. */ #if !defined (LSE_VALUE) #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ #endif /* LSE_VALUE */ /* Tip: To avoid modifying this file each time you need to use different HSE, === you can define the HSE value in your toolchain compiler preprocessor. */ /* ########################### System Configuration ######################### */ /** * @brief This is the HAL system configuration section */ #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ #define TICK_INT_PRIORITY ((uint32_t)(1<<__NVIC_PRIO_BITS) - 1) /*!< tick interrupt priority (lowest by default) */ /* Warning: Must be set to higher priority for HAL_Delay() */ /* and HAL_GetTick() usage under interrupt context */ #define USE_RTOS 0 #define PREFETCH_ENABLE 1 #define INSTRUCTION_CACHE_ENABLE 0 #define DATA_CACHE_ENABLE 0 /* ########################## Assert Selection ############################## */ /** * @brief Uncomment the line below to expanse the "assert_param" macro in the * HAL drivers code */ /*#define USE_FULL_ASSERT 1*/ /* Includes ------------------------------------------------------------------*/ /** * @brief Include module's header file */ #ifdef HAL_RCC_MODULE_ENABLED #include "stm32f0xx_hal_rcc.h" #endif /* HAL_RCC_MODULE_ENABLED */ #ifdef HAL_GPIO_MODULE_ENABLED #include "stm32f0xx_hal_gpio.h" #endif /* HAL_GPIO_MODULE_ENABLED */ #ifdef HAL_DMA_MODULE_ENABLED #include "stm32f0xx_hal_dma.h" #endif /* HAL_DMA_MODULE_ENABLED */ #ifdef HAL_CORTEX_MODULE_ENABLED #include "stm32f0xx_hal_cortex.h" #endif /* HAL_CORTEX_MODULE_ENABLED */ #ifdef HAL_ADC_MODULE_ENABLED #include "stm32f0xx_hal_adc.h" #endif /* HAL_ADC_MODULE_ENABLED */ #ifdef HAL_CAN_MODULE_ENABLED #include "stm32f0xx_hal_can.h" #endif /* HAL_CAN_MODULE_ENABLED */ #ifdef HAL_CEC_MODULE_ENABLED #include "stm32f0xx_hal_cec.h" #endif /* HAL_CEC_MODULE_ENABLED */ #ifdef HAL_COMP_MODULE_ENABLED #include "stm32f0xx_hal_comp.h" #endif /* HAL_COMP_MODULE_ENABLED */ #ifdef HAL_CRC_MODULE_ENABLED #include "stm32f0xx_hal_crc.h" #endif /* HAL_CRC_MODULE_ENABLED */ #ifdef HAL_DAC_MODULE_ENABLED #include "stm32f0xx_hal_dac.h" #endif /* HAL_DAC_MODULE_ENABLED */ #ifdef HAL_FLASH_MODULE_ENABLED #include "stm32f0xx_hal_flash.h" #endif /* HAL_FLASH_MODULE_ENABLED */ #ifdef HAL_I2C_MODULE_ENABLED #include "stm32f0xx_hal_i2c.h" #endif /* HAL_I2C_MODULE_ENABLED */ #ifdef HAL_I2S_MODULE_ENABLED #include "stm32f0xx_hal_i2s.h" #endif /* HAL_I2S_MODULE_ENABLED */ #ifdef HAL_IRDA_MODULE_ENABLED #include "stm32f0xx_hal_irda.h" #endif /* HAL_IRDA_MODULE_ENABLED */ #ifdef HAL_IWDG_MODULE_ENABLED #include "stm32f0xx_hal_iwdg.h" #endif /* HAL_IWDG_MODULE_ENABLED */ #ifdef HAL_PCD_MODULE_ENABLED #include "stm32f0xx_hal_pcd.h" #endif /* HAL_PCD_MODULE_ENABLED */ #ifdef HAL_PWR_MODULE_ENABLED #include "stm32f0xx_hal_pwr.h" #endif /* HAL_PWR_MODULE_ENABLED */ #ifdef HAL_RTC_MODULE_ENABLED #include "stm32f0xx_hal_rtc.h" #endif /* HAL_RTC_MODULE_ENABLED */ #ifdef HAL_SMARTCARD_MODULE_ENABLED #include "stm32f0xx_hal_smartcard.h" #endif /* HAL_SMARTCARD_MODULE_ENABLED */ #ifdef HAL_SMBUS_MODULE_ENABLED #include "stm32f0xx_hal_smbus.h" #endif /* HAL_SMBUS_MODULE_ENABLED */ #ifdef HAL_SPI_MODULE_ENABLED #include "stm32f0xx_hal_spi.h" #endif /* HAL_SPI_MODULE_ENABLED */ #ifdef HAL_TIM_MODULE_ENABLED #include "stm32f0xx_hal_tim.h" #endif /* HAL_TIM_MODULE_ENABLED */ #ifdef HAL_TSC_MODULE_ENABLED #include "stm32f0xx_hal_tsc.h" #endif /* HAL_TSC_MODULE_ENABLED */ #ifdef HAL_UART_MODULE_ENABLED #include "stm32f0xx_hal_uart.h" #endif /* HAL_UART_MODULE_ENABLED */ #ifdef HAL_USART_MODULE_ENABLED #include "stm32f0xx_hal_usart.h" #endif /* HAL_USART_MODULE_ENABLED */ #ifdef HAL_WWDG_MODULE_ENABLED #include "stm32f0xx_hal_wwdg.h" #endif /* HAL_WWDG_MODULE_ENABLED */ /* Exported macro ------------------------------------------------------------*/ #ifdef USE_FULL_ASSERT /** * @brief The assert_param macro is used for function's parameters check. * @param expr: If expr is false, it calls assert_failed function * which reports the name of the source file and the source * line number of the call that failed. * If expr is true, it returns no value. * @retval None */ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) /* Exported functions ------------------------------------------------------- */ void assert_failed(uint8_t* file, uint32_t line); #else #define assert_param(expr) ((void)0) #endif /* USE_FULL_ASSERT */ #ifdef __cplusplus } #endif #endif /* __STM32F0xx_HAL_CONF_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/