mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L053R8/stm32l0xx_hal_cryp.c
- Revision:
- 181:a4cbdfbbd2f4
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L053R8/stm32l0xx_hal_cryp.c Wed May 07 13:15:08 2014 +0100 @@ -0,0 +1,2090 @@ +/** + ****************************************************************************** + * @file stm32l0xx_hal_cryp.c + * @author MCD Application Team + * @version V1.0.0 + * @date 22-April-2014 + * @brief CRYP HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the Cryptography (CRYP) peripheral: + * + Initialization and de-initialization functions + * + Processing functions by algorithm using polling mode + * + Processing functions by algorithm using interrupt mode + * + Processing functions by algorithm using DMA mode + * + Peripheral State functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The CRYP HAL driver can be used as follows: + + (#)Initialize the CRYP low level resources by implementing the HAL_CRYP_MspInit(): + (##) Enable the CRYP interface clock using __CRYP_CLK_ENABLE() + (##) In case of using interrupts (e.g. HAL_AES_ECB_Encrypt_IT()) + (+) Configure the CRYP interrupt priority using HAL_NVIC_SetPriority() + (+) Enable the CRYP IRQ handler using HAL_NVIC_EnableIRQ() + (+) In CRYP IRQ handler, call HAL_CRYP_IRQHandler() + (##) In case of using DMA to control data transfer (e.g. HAL_AES_ECB_Encrypt_DMA()) + (+) Enable the DMA1 interface clock using + (++) __DMA1_CLK_ENABLE() + (+) Configure and enable two DMA Channels one for managing data transfer from + memory to peripheral (input channel) and another channel for managing data + transfer from peripheral to memory (output channel) + (+) Associate the initilalized DMA handle to the CRYP DMA handle + using __HAL_LINKDMA() + (+) Configure the priority and enable the NVIC for the transfer complete + interrupt on the two DMA Streams. The output stream should have higher + priority than the input stream. + (++) HAL_NVIC_SetPriority() + (++) HAL_NVIC_EnableIRQ() + + (#)Initialize the CRYP HAL using HAL_CRYP_Init(). This function configures mainly: + (##) The data type: 1-bit, 8-bit, 16-bit and 32-bit + (##) The encryption/decryption key. + (##) The initialization vector (counter). It is not used ECB mode. + + (#)Three processing (encryption/decryption) functions are available: + (##) Polling mode: encryption and decryption APIs are blocking functions + i.e. they process the data and wait till the processing is finished + e.g. HAL_CRYP_AESCBC_Encrypt() + (##) Interrupt mode: encryption and decryption APIs are not blocking functions + i.e. they process the data under interrupt + e.g. HAL_CRYP_AESCBC_Encrypt_IT() + (##) DMA mode: encryption and decryption APIs are not blocking functions + i.e. the data transfer is ensured by DMA + e.g. HAL_CRYP_AESCBC_Encrypt_DMA() + + (#)When the processing function is called at first time after HAL_CRYP_Init() + the CRYP peripheral is initialized and processes the buffer in input. + At second call, the processing function performs an append of the already + processed buffer. + When a new data block is to be processed, call HAL_CRYP_Init() then the + processing function. + + (#)Call HAL_CRYP_DeInit() to deinitialize the CRYP peripheral. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l0xx_hal.h" + +/** @addtogroup STM32L0xx_HAL_Driver + * @{ + */ + +/** @defgroup CRYP + * @brief CRYP HAL module driver. + * @{ + */ + +#ifdef HAL_CRYP_MODULE_ENABLED +#if !defined (STM32L051xx) && !defined (STM32L052xx) && !defined (STM32L053xx) + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define CRYP_ALGO_CHAIN_MASK (AES_CR_MODE | AES_CR_CHMOD) +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector); +static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key); +static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout); +static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma); +static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma); +static void CRYP_DMAError(DMA_HandleTypeDef *hdma); +static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr); +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup CRYP_Private_Functions + * @{ + */ + +/** @defgroup CRYP_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions. + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) Initialize the CRYP according to the specified parameters + in the CRYP_InitTypeDef and creates the associated handle + (+) DeInitialize the CRYP peripheral + (+) Initialize the CRYP MSP + (+) DeInitialize CRYP MSP + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the CRYP according to the specified + * parameters in the CRYP_InitTypeDef and creates the associated handle. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp) +{ + /* Check the parameters */ + assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType)); + + /* Check the CRYP handle allocation */ + if(hcryp == NULL) + { + return HAL_ERROR; + } + + if(hcryp->State == HAL_CRYP_STATE_RESET) + { + /* Init the low level hardware */ + HAL_CRYP_MspInit(hcryp); + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Set the data type*/ + AES->CR = hcryp->Init.DataType; + + /* Reset CrypInCount and CrypOutCount */ + hcryp->CrypInCount = 0; + hcryp->CrypOutCount = 0; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Set the default CRYP phase */ + hcryp->Phase = HAL_CRYP_PHASE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief DeInitializes the CRYP peripheral. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp) +{ + /* Check the CRYP handle allocation */ + if(hcryp == NULL) + { + return HAL_ERROR; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Set the default CRYP phase */ + hcryp->Phase = HAL_CRYP_PHASE_READY; + + /* Reset CrypInCount and CrypOutCount */ + hcryp->CrypInCount = 0; + hcryp->CrypOutCount = 0; + + /* Disable the CRYP Peripheral Clock */ + __HAL_CRYP_DISABLE(); + + /* DeInit the low level hardware: CLOCK, NVIC.*/ + HAL_CRYP_MspDeInit(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP MSP. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +__weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_MspInit could be implemented in the user file + */ +} + +/** + * @brief DeInitializes CRYP MSP. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +__weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup CRYP_Group2 AES processing functions + * @brief processing functions. + * +@verbatim + ============================================================================== + ##### AES processing functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) Encrypt plaintext using AES algorithm in different chaining modes + (+) Decrypt cyphertext using AES algorithm in different chaining modes + [..] Three processing functions are available: + (+) Polling mode + (+) Interrupt mode + (+) DMA mode + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the CRYP peripheral in AES ECB encryption mode + * then encrypt pPlainData. The cypher data are available in pCypherData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pCypherData: Pointer to the cyphertext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CBC encryption mode + * then encrypt pPlainData. The cypher data are available in pCypherData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pCypherData: Pointer to the cyphertext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR encryption mode + * then encrypt pPlainData. The cypher data are available in pCypherData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pCypherData: Pointer to the cyphertext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + + + +/** + * @brief Initializes the CRYP peripheral in AES ECB decryption mode + * then decrypted pCypherData. The cypher data are available in pPlainData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pPlainData: Pointer to the plaintext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_KEYDERDECRYPT); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES ECB decryption mode + * then decrypted pCypherData. The cypher data are available in pPlainData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pPlainData: Pointer to the plaintext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CBC decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_KEYDERDECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR decryption mode + * then decrypted pCypherData. The cypher data are available in pPlainData + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pPlainData: Pointer to the plaintext buffer + * @param Timeout: Specify Timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) +{ + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CTR decryption mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_DECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Write Plain Data and Get Cypher Data */ + if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES ECB encryption mode using Interrupt. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pPlainData; + hcryp->pCrypOutBuffPtr = pCypherData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Data Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is encrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CBC encryption mode using Interrupt. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pPlainData; + hcryp->pCrypOutBuffPtr = pCypherData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CBC mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Data Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is encrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR encryption mode using Interrupt. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pPlainData; + hcryp->pCrypOutBuffPtr = pCypherData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CTR mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Data Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is encrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + + +/** + * @brief Initializes the CRYP peripheral in AES ECB decryption mode using Interrupt. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pCypherData; + hcryp->pCrypOutBuffPtr = pPlainData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_KEYDERDECRYPT); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Output register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is decrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CBC decryption mode using IT. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pCypherData; + hcryp->pCrypOutBuffPtr = pPlainData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CBC decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_KEYDERDECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is decrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR decryption mode using Interrupt. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if(hcryp->State == HAL_CRYP_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + /* Get the buffer addresses and sizes */ + hcryp->CrypInCount = Size; + hcryp->pCrypInBuffPtr = pCypherData; + hcryp->pCrypOutBuffPtr = pPlainData; + hcryp->CrypOutCount = Size; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CTR decryption mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_DECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Enable Interrupts */ + __HAL_CRYP_ENABLE_IT(AES_IT_CC); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); + + /* Get the last input data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + + /* Return function status */ + return HAL_OK; + } + + else if(__HAL_CRYP_GET_FLAG(AES_FLAG_CCF)) + { + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Get the last Output data adress */ + outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; + + /* Read the Output block from the Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + + hcryp->pCrypOutBuffPtr += 16; + hcryp->CrypOutCount -= 16; + + /* Check if all input text is decrypted */ + if(hcryp->CrypOutCount == 0) + { + /* Disable Computation Complete Interrupt */ + __HAL_CRYP_DISABLE_IT(AES_IT_CC); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call computation complete callback */ + HAL_CRYP_ComputationCpltCallback(hcryp); + } + else /* Process the rest of input text */ + { + /* Get the last Intput data adress */ + inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; + + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + hcryp->pCrypInBuffPtr += 16; + hcryp->CrypInCount -= 16; + } + } + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CRYP peripheral in AES ECB encryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pPlainData; + outputaddr = (uint32_t)pCypherData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pPlainData; + outputaddr = (uint32_t)pCypherData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR encryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pPlainData: Pointer to the plaintext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16. + * @param pCypherData: Pointer to the cyphertext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pPlainData; + outputaddr = (uint32_t)pCypherData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Set the CRYP peripheral in AES ECB mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Initializes the CRYP peripheral in AES ECB decryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pCypherData; + outputaddr = (uint32_t)pPlainData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES ECB decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB_KEYDERDECRYPT); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pCypherData; + outputaddr = (uint32_t)pPlainData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Reset the CHMOD & MODE bits & */ + AES->CR &= (uint32_t)(~CRYP_ALGO_CHAIN_MASK); + + /* Set the CRYP peripheral in AES CBC decryption mode (with key derivation) */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC_KEYDERDECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Initializes the CRYP peripheral in AES CTR decryption mode using DMA. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param pCypherData: Pointer to the cyphertext buffer + * @param Size: Length of the plaintext buffer, must be a multiple of 16 + * @param pPlainData: Pointer to the plaintext buffer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) +{ + uint32_t inputaddr; + uint32_t outputaddr; + + if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) + { + /* Process Locked */ + __HAL_LOCK(hcryp); + + inputaddr = (uint32_t)pCypherData; + outputaddr = (uint32_t)pPlainData; + + /* Change the CRYP state */ + hcryp->State = HAL_CRYP_STATE_BUSY; + + /* Check if initialization phase has already been performed */ + if(hcryp->Phase == HAL_CRYP_PHASE_READY) + { + /* Set the key */ + CRYP_SetKey(hcryp, hcryp->Init.pKey); + + /* Set the CRYP peripheral in AES CTR mode */ + __HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR_DECRYPT); + + /* Set the Initialization Vector */ + CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect); + + /* Set the phase */ + hcryp->Phase = HAL_CRYP_PHASE_PROCESS; + } + + /* Set the input and output addresses and start DMA transfer */ + CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + /* Return function status */ + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @} + */ + + +/** @defgroup CRYP_Group3 DMA callback functions + * @brief DMA callback functions. + * +@verbatim + ============================================================================== + ##### DMA callback functions ##### + ============================================================================== + [..] This section provides DMA callback functions: + (+) DMA Input data transfer complete + (+) DMA Output data transfer complete + (+) DMA error + +@endverbatim + * @{ + */ + +/** + * @brief Input Computation completed callbacks. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +__weak void HAL_CRYP_ComputationCpltCallback(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_ComputationCpltCallback could be implemented in the user file + */ +} + +/** + * @brief CRYP error callbacks. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ + __weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_ErrorCallback could be implemented in the user file + */ +} + +/** + * @brief Input transfer completed callbacks. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +__weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_InCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Output transfer completed callbacks. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +__weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CRYP_OutCpltCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup CRYP_Group4 CRYP IRQ handler + * @brief CRYP IRQ handler. + * +@verbatim + ============================================================================== + ##### CRYP IRQ handler management ##### + ============================================================================== +[..] This section provides CRYP IRQ handler function. + +@endverbatim + * @{ + */ + +/** + * @brief This function handles CRYP interrupt request. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval None + */ +void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp) +{ + switch(AES->CR & CRYP_CR_ALGOMODE_DIRECTION) + { + case CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT: + HAL_CRYP_AESECB_Encrypt_IT(hcryp, NULL, 0, NULL); + break; + + case CRYP_CR_ALGOMODE_AES_ECB_KEYDERDECRYPT: + HAL_CRYP_AESECB_Decrypt_IT(hcryp, NULL, 0, NULL); + break; + + case CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT: + HAL_CRYP_AESCBC_Encrypt_IT(hcryp, NULL, 0, NULL); + break; + + case CRYP_CR_ALGOMODE_AES_CBC_KEYDERDECRYPT: + HAL_CRYP_AESCBC_Decrypt_IT(hcryp, NULL, 0, NULL); + break; + + case CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT: + HAL_CRYP_AESCTR_Encrypt_IT(hcryp, NULL, 0, NULL); + break; + + case CRYP_CR_ALGOMODE_AES_CTR_DECRYPT: + HAL_CRYP_AESCTR_Decrypt_IT(hcryp, NULL, 0, NULL); + break; + + default: + break; + } +} + +/** + * @} + */ + +/** @defgroup CRYP_Group5 Peripheral State functions + * @brief Peripheral State functions. + * +@verbatim + ============================================================================== + ##### Peripheral State functions ##### + ============================================================================== + [..] + This subsection permits to get in run-time the status of the peripheral. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the CRYP state. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @retval HAL state + */ +HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp) +{ + return hcryp->State; +} + +/** + * @} + */ + +/** + * @brief DMA CRYP Input Data process complete callback. + * @param hdma: DMA handle + * @retval None + */ +static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma) +{ + CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + /* Disable the DMA transfer for input request */ + AES->CR &= (uint32_t)(~AES_CR_DMAINEN); + + /* Call input data transfer complete callback */ + HAL_CRYP_InCpltCallback(hcryp); +} + +/** + * @brief DMA CRYP Output Data process complete callback. + * @param hdma: DMA handle + * @retval None + */ +static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma) +{ + CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + /* Disable the DMA transfer for output request by resetting the DOEN bit + in the DMACR register */ + AES->CR &= (uint32_t)(~AES_CR_DMAOUTEN); + + /* Disable CRYP */ + __HAL_CRYP_DISABLE(); + + /* Change the CRYP state to ready */ + hcryp->State = HAL_CRYP_STATE_READY; + + /* Call output data transfer complete callback */ + HAL_CRYP_OutCpltCallback(hcryp); +} + +/** + * @brief DMA CRYP communication error callback. + * @param hdma: DMA handle + * @retval None + */ +static void CRYP_DMAError(DMA_HandleTypeDef *hdma) +{ + CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + hcryp->State= HAL_CRYP_STATE_READY; + HAL_CRYP_ErrorCallback(hcryp); +} + +/** + * @brief Writes the Key in Key registers. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param Key: Pointer to Key buffer + * @param KeySize: Size of Key + * @retval None + */ +static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key) +{ + uint32_t keyaddr = (uint32_t)Key; + + AES->KEYR3 = __REV(*(uint32_t*)(keyaddr)); + keyaddr+=4; + AES->KEYR2 = __REV(*(uint32_t*)(keyaddr)); + keyaddr+=4; + AES->KEYR1 = __REV(*(uint32_t*)(keyaddr)); + keyaddr+=4; + AES->KEYR0 = __REV(*(uint32_t*)(keyaddr)); +} + +/** + * @brief Writes the InitVector/InitCounter in IV registers. + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param InitVector: Pointer to InitVector/InitCounter buffer + * @param IVSize: Size of the InitVector/InitCounter + * @retval None + */ +static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector) +{ + uint32_t ivaddr = (uint32_t)InitVector; + + AES->IVR3 = __REV(*(uint32_t*)(ivaddr)); + ivaddr+=4; + AES->IVR2 = __REV(*(uint32_t*)(ivaddr)); + ivaddr+=4; + AES->IVR1 = __REV(*(uint32_t*)(ivaddr)); + ivaddr+=4; + AES->IVR0 = __REV(*(uint32_t*)(ivaddr)); +} + +/** + * @brief Process Data: Writes Input data in polling mode and read the output data + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param Input: Pointer to the Input buffer + * @param Ilength: Length of the Input buffer, must be a multiple of 16. + * @param Output: Pointer to the returned buffer + * @retval None + */ +static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout) +{ + uint32_t tickstart = 0; + + uint32_t i = 0; + uint32_t inputaddr = (uint32_t)Input; + uint32_t outputaddr = (uint32_t)Output; + + for(i=0; (i < Ilength); i+=16) + { + /* Write the Input block in the Data Input register */ + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + AES->DINR = *(uint32_t*)(inputaddr); + inputaddr+=4; + + /* Get timeout */ + tickstart = HAL_GetTick(); + + while(HAL_IS_BIT_CLR(AES->SR, AES_SR_CCF)) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((HAL_GetTick() - tickstart ) > Timeout) + { + /* Change state */ + hcryp->State = HAL_CRYP_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hcryp); + + return HAL_TIMEOUT; + } + } + } + /* Clear CCF Flag */ + AES->CR |= AES_CR_CCFC; + + /* Read the Output block from the Data Output Register */ + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + *(uint32_t*)(outputaddr) = AES->DOUTR; + outputaddr+=4; + } + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Set the DMA configuration and start the DMA transfer + * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains + * the configuration information for CRYP module + * @param inputaddr: address of the Input buffer + * @param Size: Size of the Input buffer, must be a multiple of 16. + * @param outputaddr: address of the Output buffer + * @retval None + */ +static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr) +{ + /* Set the CRYP DMA transfer complete callback */ + hcryp->hdmain->XferCpltCallback = CRYP_DMAInCplt; + /* Set the DMA error callback */ + hcryp->hdmain->XferErrorCallback = CRYP_DMAError; + + /* Set the CRYP DMA transfer complete callback */ + hcryp->hdmaout->XferCpltCallback = CRYP_DMAOutCplt; + /* Set the DMA error callback */ + hcryp->hdmaout->XferErrorCallback = CRYP_DMAError; + + /* Enable the DMA In DMA Stream */ + HAL_DMA_Start_IT(hcryp->hdmain, inputaddr, (uint32_t)&AES->DINR, Size/4); + + /* Enable the DMA Out DMA Stream */ + HAL_DMA_Start_IT(hcryp->hdmaout, (uint32_t)&AES->DOUTR, outputaddr, Size/4); + + /* Enable In and Out DMA requests */ + AES->CR |= (AES_CR_DMAINEN | AES_CR_DMAOUTEN); + + /* Enable CRYP */ + __HAL_CRYP_ENABLE(); +} + + + + + + +/** + * @} + */ +#endif /* STM32L051xx && STM32L052xx && STM32L053xx*/ +#endif /* HAL_CRYP_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/