shao ziyang
mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F3XX/stm32f30x_pwr.c
- Revision:
- 155:8435094ec241
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_STM32F3XX/stm32f30x_pwr.c Tue Apr 08 09:15:06 2014 +0100
@@ -0,0 +1,548 @@
+/**
+ ******************************************************************************
+ * @file stm32f30x_pwr.c
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 27-February-2014
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the Power Controller (PWR) peripheral:
+ * + Backup Domain Access
+ * + PVD configuration
+ * + WakeUp pins configuration
+ * + Low Power modes configuration
+ * + Flags management
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f30x_pwr.h"
+#include "stm32f30x_rcc.h"
+
+/** @addtogroup STM32F30x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup PWR
+ * @brief PWR driver modules
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* --------- PWR registers bit address in the alias region ---------- */
+#define PWR_OFFSET (PWR_BASE - PERIPH_BASE)
+
+/* --- CR Register ---*/
+
+/* Alias word address of DBP bit */
+#define CR_OFFSET (PWR_OFFSET + 0x00)
+#define DBP_BitNumber 0x08
+#define CR_DBP_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (DBP_BitNumber * 4))
+
+/* Alias word address of PVDE bit */
+#define PVDE_BitNumber 0x04
+#define CR_PVDE_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PVDE_BitNumber * 4))
+
+/* ------------------ PWR registers bit mask ------------------------ */
+
+/* CR register bit mask */
+#define CR_DS_MASK ((uint32_t)0xFFFFFFFC)
+#define CR_PLS_MASK ((uint32_t)0xFFFFFF1F)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup PWR_Private_Functions
+ * @{
+ */
+
+/** @defgroup PWR_Group1 Backup Domain Access function
+ * @brief Backup Domain Access function
+ *
+@verbatim
+ ==============================================================================
+ ##### Backup Domain Access function #####
+ ==============================================================================
+
+ [..] After reset, the Backup Domain Registers (RCC BDCR Register, RTC registers
+ and RTC backup registers) are protected against possible stray write accesses.
+ [..] To enable access to Backup domain use the PWR_BackupAccessCmd(ENABLE) function.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the PWR peripheral registers to their default reset values.
+ * @param None
+ * @retval None
+ */
+void PWR_DeInit(void)
+{
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, DISABLE);
+}
+
+/**
+ * @brief Enables or disables access to the RTC and backup registers.
+ * @note If the HSE divided by 32 is used as the RTC clock, the
+ * Backup Domain Access should be kept enabled.
+ * @param NewState: new state of the access to the RTC and backup registers.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void PWR_BackupAccessCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) CR_DBP_BB = (uint32_t)NewState;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Group2 PVD configuration functions
+ * @brief PVD configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### PVD configuration functions #####
+ ==============================================================================
+ [..]
+ (+) The PVD is used to monitor the VDD power supply by comparing it to a threshold
+ selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
+ (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower than the
+ PVD threshold. This event is internally connected to the EXTI line16
+ and can generate an interrupt if enabled through the EXTI registers.
+ (+) The PVD is stopped in Standby mode.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
+ * @param PWR_PVDLevel: specifies the PVD detection level
+ * This parameter can be one of the following values:
+ * @arg PWR_PVDLevel_0: PVD detection level set to 2.18V
+ * @arg PWR_PVDLevel_1: PVD detection level set to 2.28V
+ * @arg PWR_PVDLevel_2: PVD detection level set to 2.38V
+ * @arg PWR_PVDLevel_3: PVD detection level set to 2.48V
+ * @arg PWR_PVDLevel_4: PVD detection level set to 2.58V
+ * @arg PWR_PVDLevel_5: PVD detection level set to 2.68V
+ * @arg PWR_PVDLevel_6: PVD detection level set to 2.78V
+ * @arg PWR_PVDLevel_7: PVD detection level set to 2.88V
+ * @retval None
+ */
+void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));
+
+ tmpreg = PWR->CR;
+
+ /* Clear PLS[7:5] bits */
+ tmpreg &= CR_PLS_MASK;
+
+ /* Set PLS[7:5] bits according to PWR_PVDLevel value */
+ tmpreg |= PWR_PVDLevel;
+
+ /* Store the new value */
+ PWR->CR = tmpreg;
+}
+
+/**
+ * @brief Enables or disables the Power Voltage Detector(PVD).
+ * @param NewState: new state of the PVD.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void PWR_PVDCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)NewState;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Group3 WakeUp pins configuration functions
+ * @brief WakeUp pins configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### WakeUp pins configuration functions #####
+ ===============================================================================
+ [..]
+ (+) WakeUp pins are used to wakeup the system from Standby mode. These pins are
+ forced in input pull down configuration and are active on rising edges.
+ (+) There are three WakeUp pins: WakeUp Pin 1 on PA.00, WakeUp Pin 2 on PC.13 and
+ WakeUp Pin 3 on PE.06.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables or disables the WakeUp Pin functionality.
+ * @param PWR_WakeUpPin: specifies the WakeUpPin.
+ * This parameter can be: PWR_WakeUpPin_1, PWR_WakeUpPin_2 or PWR_WakeUpPin_3.
+ * @param NewState: new state of the WakeUp Pin functionality.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void PWR_WakeUpPinCmd(uint32_t PWR_WakeUpPin, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_PWR_WAKEUP_PIN(PWR_WakeUpPin));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the EWUPx pin */
+ PWR->CSR |= PWR_WakeUpPin;
+ }
+ else
+ {
+ /* Disable the EWUPx pin */
+ PWR->CSR &= ~PWR_WakeUpPin;
+ }
+}
+
+/**
+ * @}
+ */
+
+
+/** @defgroup PWR_Group4 Low Power modes configuration functions
+ * @brief Low Power modes configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Low Power modes configuration functions #####
+ ==============================================================================
+
+ [..] The devices feature three low-power modes:
+ (+) Sleep mode: Cortex-M4 core stopped, peripherals kept running.
+ (+) Stop mode: all clocks are stopped, regulator running, regulator in low power mode
+ (+) Standby mode: VCORE domain powered off
+
+ *** Sleep mode ***
+ ==================
+ [..]
+ (+) Entry:
+ (++) The Sleep mode is entered by executing the WFE() or WFI() instructions.
+ (+) Exit:
+ (++) Any peripheral interrupt acknowledged by the nested vectored interrupt
+ controller (NVIC) can wake up the device from Sleep mode.
+
+ *** Stop mode ***
+ =================
+ [..] In Stop mode, all clocks in the VCORE domain are stopped, the PLL, the HSI,
+ and the HSE RC oscillators are disabled. Internal SRAM and register
+ contents are preserved.
+ The voltage regulator can be configured either in normal or low-power mode.
+
+ (+) Entry:
+ (++) The Stop mode is entered using the PWR_EnterSTOPMode(PWR_Regulator_LowPower,)
+ function with regulator in LowPower or with Regulator ON.
+ (+) Exit:
+ (++) Any EXTI Line (Internal or External) configured in Interrupt/Event mode
+ or any internal IPs (I2C or UASRT) wakeup event.
+
+ *** Standby mode ***
+ ====================
+ [..] The Standby mode allows to achieve the lowest power consumption. It is based
+ on the Cortex-M4 deepsleep mode, with the voltage regulator disabled.
+ The VCORE domain is consequently powered off. The PLL, the HSI, and the HSE
+ oscillator are also switched off. SRAM and register
+ contents are lost except for the Backup domain (RTC registers, RTC backup
+ registers and Standby circuitry).
+
+ [..] The voltage regulator is OFF.
+
+ (+) Entry:
+ (++) The Standby mode is entered using the PWR_EnterSTANDBYMode() function.
+ (+) Exit:
+ (++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wakeup,
+ tamper event, time-stamp event, external reset in NRST pin, IWDG reset.
+
+ *** Auto-wakeup (AWU) from low-power mode ***
+ =============================================
+ [..] The MCU can be woken up from low-power mode by an RTC Alarm event, a tamper
+ event, a time-stamp event, or a comparator event, without depending on an
+ external interrupt (Auto-wakeup mode).
+
+ (+) RTC auto-wakeup (AWU) from the Stop mode
+ (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to:
+ (+++) Configure the EXTI Line 17 to be sensitive to rising edges (Interrupt
+ or Event modes) using the EXTI_Init() function.
+ (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function
+ (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm()
+ and RTC_AlarmCmd() functions.
+ (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it
+ is necessary to:
+ (+++) Configure the EXTI Line 19 to be sensitive to rising edges (Interrupt
+ or Event modes) using the EXTI_Init() function.
+ (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig()
+ function.
+ (+++) Configure the RTC to detect the tamper or time stamp event using the
+ RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
+ functions.
+
+ (+) RTC auto-wakeup (AWU) from the Standby mode
+ (++) To wake up from the Standby mode with an RTC alarm event, it is necessary to:
+ (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function.
+ (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm()
+ and RTC_AlarmCmd() functions.
+ (++) To wake up from the Standby mode with an RTC Tamper or time stamp event, it
+ is necessary to:
+ (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig()
+ function.
+ (+++) Configure the RTC to detect the tamper or time stamp event using the
+ RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
+ functions.
+
+ (+) Comparator auto-wakeup (AWU) from the Stop mode
+ (++) To wake up from the Stop mode with a comparator wakeup event, it is necessary to:
+ (+++) Configure the correspondant comparator EXTI Line to be sensitive to
+ the selected edges (falling, rising or falling and rising)
+ (Interrupt or Event modes) using the EXTI_Init() function.
+ (+++) Configure the comparator to generate the event.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enters Sleep mode.
+ * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
+ * @param PWR_SLEEPEntry: specifies if SLEEP mode in entered with WFI or WFE instruction.
+ * This parameter can be one of the following values:
+ * @arg PWR_SLEEPEntry_WFI: enter SLEEP mode with WFI instruction
+ * @arg PWR_SLEEPEntry_WFE: enter SLEEP mode with WFE instruction
+ * @retval None
+ */
+void PWR_EnterSleepMode(uint8_t PWR_SLEEPEntry)
+{
+ /* Check the parameters */
+ assert_param(IS_PWR_SLEEP_ENTRY(PWR_SLEEPEntry));
+
+ /* Clear SLEEPDEEP bit of Cortex System Control Register */
+ SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
+
+ /* Select SLEEP mode entry -------------------------------------------------*/
+ if(PWR_SLEEPEntry == PWR_SLEEPEntry_WFI)
+ {
+ /* Request Wait For Interrupt */
+ __WFI();
+ }
+ else
+ {
+ /* Request Wait For Event */
+ __WFE();
+ }
+}
+
+/**
+ * @brief Enters STOP mode.
+ * @note In Stop mode, all I/O pins keep the same state as in Run mode.
+ * @note When exiting Stop mode by issuing an interrupt or a wakeup event,
+ * the HSI RC oscillator is selected as system clock.
+ * @note When the voltage regulator operates in low power mode, an additional
+ * startup delay is incurred when waking up from Stop mode.
+ * By keeping the internal regulator ON during Stop mode, the consumption
+ * is higher although the startup time is reduced.
+ * @param PWR_Regulator: specifies the regulator state in STOP mode.
+ * This parameter can be one of the following values:
+ * @arg PWR_Regulator_ON: STOP mode with regulator ON
+ * @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
+ * @param PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
+ * This parameter can be one of the following values:
+ * @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
+ * @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
+ * @retval None
+ */
+void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_PWR_REGULATOR(PWR_Regulator));
+ assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
+
+ /* Select the regulator state in STOP mode ---------------------------------*/
+ tmpreg = PWR->CR;
+ /* Clear PDDS and LPDSR bits */
+ tmpreg &= CR_DS_MASK;
+
+ /* Set LPDSR bit according to PWR_Regulator value */
+ tmpreg |= PWR_Regulator;
+
+ /* Store the new value */
+ PWR->CR = tmpreg;
+
+ /* Set SLEEPDEEP bit of Cortex System Control Register */
+ SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
+
+ /* Select STOP mode entry --------------------------------------------------*/
+ if(PWR_STOPEntry == PWR_STOPEntry_WFI)
+ {
+ /* Request Wait For Interrupt */
+ __WFI();
+ }
+ else
+ {
+ /* Request Wait For Event */
+ __WFE();
+ }
+ /* Reset SLEEPDEEP bit of Cortex System Control Register */
+ SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
+}
+
+/**
+ * @brief Enters STANDBY mode.
+ * @note In Standby mode, all I/O pins are high impedance except for:
+ * @note Reset pad (still available)
+ * @note RTC_AF1 pin (PC13) if configured for Wakeup pin 2 (WKUP2), tamper,
+ * time-stamp, RTC Alarm out, or RTC clock calibration out.
+ * @note WKUP pin 1 (PA0) and WKUP pin 3 (PE6), if enabled.
+ * @param None
+ * @retval None
+ */
+void PWR_EnterSTANDBYMode(void)
+{
+ /* Clear Wakeup flag */
+ PWR->CR |= PWR_CR_CWUF;
+
+ /* Select STANDBY mode */
+ PWR->CR |= PWR_CR_PDDS;
+
+ /* Set SLEEPDEEP bit of Cortex System Control Register */
+ SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
+
+/* This option is used to ensure that store operations are completed */
+#if defined ( __CC_ARM )
+ __force_stores();
+#endif
+ /* Request Wait For Interrupt */
+ __WFI();
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Group5 Flags management functions
+ * @brief Flags management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Flags management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Checks whether the specified PWR flag is set or not.
+ * @param PWR_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+ * was received from the WKUP pin or from the RTC alarm (Alarm A or Alarm B),
+ * RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+ * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+ * resumed from StandBy mode.
+ * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
+ * by the PWR_PVDCmd() function.
+ * @arg PWR_FLAG_VREFINTRDY: Internal Voltage Reference Ready flag. This
+ * flag indicates the state of the internal voltage reference, VREFINT.
+ * @retval The new state of PWR_FLAG (SET or RESET).
+ */
+FlagStatus PWR_GetFlagStatus(uint32_t PWR_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_PWR_GET_FLAG(PWR_FLAG));
+
+ if ((PWR->CSR & PWR_FLAG) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ /* Return the flag status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the PWR's pending flags.
+ * @param PWR_FLAG: specifies the flag to clear.
+ * This parameter can be one of the following values:
+ * @arg PWR_FLAG_WU: Wake Up flag
+ * @arg PWR_FLAG_SB: StandBy flag
+ * @retval None
+ */
+void PWR_ClearFlag(uint32_t PWR_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_PWR_CLEAR_FLAG(PWR_FLAG));
+
+ PWR->CR |= PWR_FLAG << 2;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/