mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F401RE/stm32f4xx_hal_sd.h
- Revision:
- 87:085cde657901
- Child:
- 106:ced8cbb51063
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F401RE/stm32f4xx_hal_sd.h Sat Feb 08 19:45:06 2014 +0000 @@ -0,0 +1,665 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_sd.h + * @author MCD Application Team + * @version V1.0.0RC2 + * @date 04-February-2014 + * @brief Header file of SD HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_SD_H +#define __STM32F4xx_HAL_SD_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_ll_sdmmc.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup SD + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +#define SD_InitTypeDef SDIO_InitTypeDef +#define SD_TypeDef SDIO_TypeDef + +/** + * @brief SDIO Handle Structure definition + */ +typedef struct +{ + SD_TypeDef *Instance; /*!< SDIO register base address */ + + SD_InitTypeDef Init; /*!< SD required parameters */ + + HAL_LockTypeDef Lock; /*!< SD locking object */ + + uint32_t CardType; /*!< SD card type */ + + uint32_t RCA; /*!< SD relative card address */ + + uint32_t CSD[4]; /*!< SD card specific data table */ + + uint32_t CID[4]; /*!< SD card identification number table */ + + __IO uint32_t SdTransferCplt; /*!< SD transfer complete flag in non blocking mode */ + + __IO uint32_t SdTransferErr; /*!< SD transfer error flag in non blocking mode */ + + __IO uint32_t DmaTransferCplt; /*!< SD DMA transfer complete flag */ + + __IO uint32_t SdOperation; /*!< SD transfer operation (read/write) */ + + DMA_HandleTypeDef *hdmarx; /*!< SD Rx DMA handle parameters */ + + DMA_HandleTypeDef *hdmatx; /*!< SD Tx DMA handle parameters */ + +}SD_HandleTypeDef; + +/** + * @brief Card Specific Data: CSD Register + */ +typedef struct +{ + __IO uint8_t CSDStruct; /*!< CSD structure */ + __IO uint8_t SysSpecVersion; /*!< System specification version */ + __IO uint8_t Reserved1; /*!< Reserved */ + __IO uint8_t TAAC; /*!< Data read access time 1 */ + __IO uint8_t NSAC; /*!< Data read access time 2 in CLK cycles */ + __IO uint8_t MaxBusClkFrec; /*!< Max. bus clock frequency */ + __IO uint16_t CardComdClasses; /*!< Card command classes */ + __IO uint8_t RdBlockLen; /*!< Max. read data block length */ + __IO uint8_t PartBlockRead; /*!< Partial blocks for read allowed */ + __IO uint8_t WrBlockMisalign; /*!< Write block misalignment */ + __IO uint8_t RdBlockMisalign; /*!< Read block misalignment */ + __IO uint8_t DSRImpl; /*!< DSR implemented */ + __IO uint8_t Reserved2; /*!< Reserved */ + __IO uint32_t DeviceSize; /*!< Device Size */ + __IO uint8_t MaxRdCurrentVDDMin; /*!< Max. read current @ VDD min */ + __IO uint8_t MaxRdCurrentVDDMax; /*!< Max. read current @ VDD max */ + __IO uint8_t MaxWrCurrentVDDMin; /*!< Max. write current @ VDD min */ + __IO uint8_t MaxWrCurrentVDDMax; /*!< Max. write current @ VDD max */ + __IO uint8_t DeviceSizeMul; /*!< Device size multiplier */ + __IO uint8_t EraseGrSize; /*!< Erase group size */ + __IO uint8_t EraseGrMul; /*!< Erase group size multiplier */ + __IO uint8_t WrProtectGrSize; /*!< Write protect group size */ + __IO uint8_t WrProtectGrEnable; /*!< Write protect group enable */ + __IO uint8_t ManDeflECC; /*!< Manufacturer default ECC */ + __IO uint8_t WrSpeedFact; /*!< Write speed factor */ + __IO uint8_t MaxWrBlockLen; /*!< Max. write data block length */ + __IO uint8_t WriteBlockPaPartial; /*!< Partial blocks for write allowed */ + __IO uint8_t Reserved3; /*!< Reserved */ + __IO uint8_t ContentProtectAppli; /*!< Content protection application */ + __IO uint8_t FileFormatGrouop; /*!< File format group */ + __IO uint8_t CopyFlag; /*!< Copy flag (OTP) */ + __IO uint8_t PermWrProtect; /*!< Permanent write protection */ + __IO uint8_t TempWrProtect; /*!< Temporary write protection */ + __IO uint8_t FileFormat; /*!< File format */ + __IO uint8_t ECC; /*!< ECC code */ + __IO uint8_t CSD_CRC; /*!< CSD CRC */ + __IO uint8_t Reserved4; /*!< Always 1 */ + +}HAL_SD_CSDTypedef; + +/** + * @brief Card Identification Data: CID Register + */ +typedef struct +{ + __IO uint8_t ManufacturerID; /*!< Manufacturer ID */ + __IO uint16_t OEM_AppliID; /*!< OEM/Application ID */ + __IO uint32_t ProdName1; /*!< Product Name part1 */ + __IO uint8_t ProdName2; /*!< Product Name part2 */ + __IO uint8_t ProdRev; /*!< Product Revision */ + __IO uint32_t ProdSN; /*!< Product Serial Number */ + __IO uint8_t Reserved1; /*!< Reserved1 */ + __IO uint16_t ManufactDate; /*!< Manufacturing Date */ + __IO uint8_t CID_CRC; /*!< CID CRC */ + __IO uint8_t Reserved2; /*!< Always 1 */ + +}HAL_SD_CIDTypedef; + +/** + * @brief SD Card Status returned by ACMD13 + */ +typedef struct +{ + __IO uint8_t DAT_BUS_WIDTH; /*!< Shows the currently defined data bus width */ + __IO uint8_t SECURED_MODE; /*!< Card is in secured mode of operation */ + __IO uint16_t SD_CARD_TYPE; /*!< Carries information about card type */ + __IO uint32_t SIZE_OF_PROTECTED_AREA; /*!< Carries information about the capacity of protected area */ + __IO uint8_t SPEED_CLASS; /*!< Carries information about the speed class of the card */ + __IO uint8_t PERFORMANCE_MOVE; /*!< Carries information about the card's performance move */ + __IO uint8_t AU_SIZE; /*!< Carries information about the card's allocation unit size */ + __IO uint16_t ERASE_SIZE; /*!< Determines the number of AUs to be erased in one operation */ + __IO uint8_t ERASE_TIMEOUT; /*!< Determines the timeout for any number of AU erase */ + __IO uint8_t ERASE_OFFSET; /*!< Carries information about the erase offset */ + +}HAL_SD_CardStatusTypedef; + +/** + * @brief SD Card information structure + */ +typedef struct +{ + HAL_SD_CSDTypedef SD_csd; /*!< SD card specific data register */ + HAL_SD_CIDTypedef SD_cid; /*!< SD card identification number register */ + uint64_t CardCapacity; /*!< Card capacity */ + uint32_t CardBlockSize; /*!< Card block size */ + uint16_t RCA; /*!< SD relative card address */ + uint8_t CardType; /*!< SD card type */ + +}HAL_SD_CardInfoTypedef; + +/** + * @brief SD Error status enumeration Structure definition + */ +typedef enum +{ +/** + * @brief SD specific error defines + */ + SD_CMD_CRC_FAIL = (1), /*!< Command response received (but CRC check failed) */ + SD_DATA_CRC_FAIL = (2), /*!< Data block sent/received (CRC check failed) */ + SD_CMD_RSP_TIMEOUT = (3), /*!< Command response timeout */ + SD_DATA_TIMEOUT = (4), /*!< Data timeout */ + SD_TX_UNDERRUN = (5), /*!< Transmit FIFO underrun */ + SD_RX_OVERRUN = (6), /*!< Receive FIFO overrun */ + SD_START_BIT_ERR = (7), /*!< Start bit not detected on all data signals in wide bus mode */ + SD_CMD_OUT_OF_RANGE = (8), /*!< Command's argument was out of range. */ + SD_ADDR_MISALIGNED = (9), /*!< Misaligned address */ + SD_BLOCK_LEN_ERR = (10), /*!< Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length */ + SD_ERASE_SEQ_ERR = (11), /*!< An error in the sequence of erase command occurs. */ + SD_BAD_ERASE_PARAM = (12), /*!< An invalid selection for erase groups */ + SD_WRITE_PROT_VIOLATION = (13), /*!< Attempt to program a write protect block */ + SD_LOCK_UNLOCK_FAILED = (14), /*!< Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card */ + SD_COM_CRC_FAILED = (15), /*!< CRC check of the previous command failed */ + SD_ILLEGAL_CMD = (16), /*!< Command is not legal for the card state */ + SD_CARD_ECC_FAILED = (17), /*!< Card internal ECC was applied but failed to correct the data */ + SD_CC_ERROR = (18), /*!< Internal card controller error */ + SD_GENERAL_UNKNOWN_ERROR = (19), /*!< General or unknown error */ + SD_STREAM_READ_UNDERRUN = (20), /*!< The card could not sustain data transfer in stream read operation. */ + SD_STREAM_WRITE_OVERRUN = (21), /*!< The card could not sustain data programming in stream mode */ + SD_CID_CSD_OVERWRITE = (22), /*!< CID/CSD overwrite error */ + SD_WP_ERASE_SKIP = (23), /*!< Only partial address space was erased */ + SD_CARD_ECC_DISABLED = (24), /*!< Command has been executed without using internal ECC */ + SD_ERASE_RESET = (25), /*!< Erase sequence was cleared before executing because an out of erase sequence command was received */ + SD_AKE_SEQ_ERROR = (26), /*!< Error in sequence of authentication. */ + SD_INVALID_VOLTRANGE = (27), + SD_ADDR_OUT_OF_RANGE = (28), + SD_SWITCH_ERROR = (29), + SD_SDIO_DISABLED = (30), + SD_SDIO_FUNCTION_BUSY = (31), + SD_SDIO_FUNCTION_FAILED = (32), + SD_SDIO_UNKNOWN_FUNCTION = (33), + +/** + * @brief Standard error defines + */ + SD_INTERNAL_ERROR = (34), + SD_NOT_CONFIGURED = (35), + SD_REQUEST_PENDING = (36), + SD_REQUEST_NOT_APPLICABLE = (37), + SD_INVALID_PARAMETER = (38), + SD_UNSUPPORTED_FEATURE = (39), + SD_UNSUPPORTED_HW = (40), + SD_ERROR = (41), + SD_OK = (0) + +}HAL_SD_ErrorTypedef; + +/** + * @brief SD Transfer state enumeration structure + */ +typedef enum +{ + SD_TRANSFER_OK = 0, /*!< Transfer success */ + SD_TRANSFER_BUSY = 1, /*!< Transfer is occurring */ + SD_TRANSFER_ERROR = 2 /*!< Transfer failed */ + +}HAL_SD_TransferStateTypedef; + +/** + * @brief SD Card State enumeration structure + */ +typedef enum +{ + SD_CARD_READY = ((uint32_t)0x00000001), /*!< Card state is ready */ + SD_CARD_IDENTIFICATION = ((uint32_t)0x00000002), /*!< Card is in identification state */ + SD_CARD_STANDBY = ((uint32_t)0x00000003), /*!< Card is in standby state */ + SD_CARD_TRANSFER = ((uint32_t)0x00000004), /*!< Card is in transfer state */ + SD_CARD_SENDING = ((uint32_t)0x00000005), /*!< Card is sending an operation */ + SD_CARD_RECEIVING = ((uint32_t)0x00000006), /*!< Card is receiving operation information */ + SD_CARD_PROGRAMMING = ((uint32_t)0x00000007), /*!< Card is in programming state */ + SD_CARD_DISCONNECTED = ((uint32_t)0x00000008), /*!< Card is disconnected */ + SD_CARD_ERROR = ((uint32_t)0x000000FF) /*!< Card is in error state */ + +}HAL_SD_CardStateTypedef; + +/** + * @brief SD Operation enumeration structure + */ +typedef enum +{ + SD_READ_SINGLE_BLOCK = 0, /*!< Read single block operation */ + SD_READ_MULTIPLE_BLOCK = 1, /*!< Read multiple blocks operation */ + SD_WRITE_SINGLE_BLOCK = 2, /*!< Write single block operation */ + SD_WRITE_MULTIPLE_BLOCK = 3 /*!< Write multiple blocks operation */ + +}HAL_SD_OperationTypedef; + + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup SD_Exported_Constants + * @{ + */ + +/** + * @brief SD Commands Index + */ +#define SD_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */ +#define SD_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */ +#define SD_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */ +#define SD_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */ +#define SD_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */ +#define SD_CMD_SDIO_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its + operating condition register (OCR) content in the response on the CMD line. */ +#define SD_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */ +#define SD_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */ +#define SD_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information + and asks the card whether card supports voltage. */ +#define SD_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */ +#define SD_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */ +#define SD_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */ +#define SD_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */ +#define SD_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */ +#define SD_CMD_HS_BUSTEST_READ ((uint8_t)14) +#define SD_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */ +#define SD_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands + (read, write, lock). Default block length is fixed to 512 Bytes. Not effective + for SDHS and SDXC. */ +#define SD_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SD_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by + STOP_TRANSMISSION command. */ +#define SD_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */ +#define SD_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */ +#define SD_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */ +#define SD_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SD_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */ +#define SD_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */ +#define SD_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */ +#define SD_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */ +#define SD_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */ +#define SD_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */ +#define SD_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */ +#define SD_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */ +#define SD_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command + system set by switch function command (CMD6). */ +#define SD_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased. + Reserved for each command system set by switch function command (CMD6). */ +#define SD_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */ +#define SD_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */ +#define SD_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */ +#define SD_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by + the SET_BLOCK_LEN command. */ +#define SD_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather + than a standard command. */ +#define SD_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card + for general purpose/application specific commands. */ +#define SD_CMD_NO_CMD ((uint8_t)64) + +/** + * @brief Following commands are SD Card Specific commands. + * SDIO_APP_CMD should be sent before sending these commands. + */ +#define SD_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus + widths are given in SCR register. */ +#define SD_CMD_SD_APP_STAUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */ +#define SD_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with + 32bit+CRC data block. */ +#define SD_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to + send its operating condition register (OCR) content in the response on the CMD line. */ +#define SD_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connects/Disconnects the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card. */ +#define SD_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */ +#define SD_CMD_SDIO_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */ +#define SD_CMD_SDIO_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */ + +/** + * @brief Following commands are SD Card Specific security commands. + * SD_CMD_APP_CMD should be sent before sending these commands. + */ +#define SD_CMD_SD_APP_GET_MKB ((uint8_t)43) /*!< For SD card only */ +#define SD_CMD_SD_APP_GET_MID ((uint8_t)44) /*!< For SD card only */ +#define SD_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45) /*!< For SD card only */ +#define SD_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46) /*!< For SD card only */ +#define SD_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47) /*!< For SD card only */ +#define SD_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48) /*!< For SD card only */ +#define SD_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18) /*!< For SD card only */ +#define SD_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25) /*!< For SD card only */ +#define SD_CMD_SD_APP_SECURE_ERASE ((uint8_t)38) /*!< For SD card only */ +#define SD_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49) /*!< For SD card only */ +#define SD_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48) /*!< For SD card only */ + +/** + * @brief Supported SD Memory Cards + */ +#define STD_CAPACITY_SD_CARD_V1_1 ((uint32_t)0x00000000) +#define STD_CAPACITY_SD_CARD_V2_0 ((uint32_t)0x00000001) +#define HIGH_CAPACITY_SD_CARD ((uint32_t)0x00000002) +#define MULTIMEDIA_CARD ((uint32_t)0x00000003) +#define SECURE_DIGITAL_IO_CARD ((uint32_t)0x00000004) +#define HIGH_SPEED_MULTIMEDIA_CARD ((uint32_t)0x00000005) +#define SECURE_DIGITAL_IO_COMBO_CARD ((uint32_t)0x00000006) +#define HIGH_CAPACITY_MMC_CARD ((uint32_t)0x00000007) +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ + +/** @defgroup SD_Interrupt_Clock + * @brief macros to handle interrupts and specific clock configurations + * @{ + */ + +/** + * @brief Enable the SD device. + * @retval None + */ +#define __HAL_SD_SDIO_ENABLE() __SDIO_ENABLE() + +/** + * @brief Disable the SD device. + * @retval None + */ +#define __HAL_SD_SDIO_DISABLE() __SDIO_DISABLE() + +/** + * @brief Enable the SDIO DMA transfer. + * @retval None + */ +#define __HAL_SD_SDIO_DMA_ENABLE() __SDIO_DMA_ENABLE() + +/** + * @brief Disable the SDIO DMA transfer. + * @retval None + */ +#define __HAL_SD_SDIO_DMA_DISABLE() __SDIO_DMA_DISABLE() + +/** + * @brief Enable the SD device interrupt. + * @param __HANDLE__: SD Handle + * @param __INTERRUPT__: specifies the SDIO interrupt sources to be enabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide + * bus mode interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt + * @retval None + */ +#define __HAL_SD_SDIO_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) + +/** + * @brief Disable the SD device interrupt. + * @param __HANDLE__: SD Handle + * @param __INTERRUPT__: specifies the SDIO interrupt sources to be disabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide + * bus mode interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt + * @retval None + */ +#define __HAL_SD_SDIO_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) + +/** + * @brief Check whether the specified SD flag is set or not. + * @param __HANDLE__: SD Handle + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) + * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode. + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_CMDACT: Command transfer in progress + * @arg SDIO_FLAG_TXACT: Data transmit in progress + * @arg SDIO_FLAG_RXACT: Data receive in progress + * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty + * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full + * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full + * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full + * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty + * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty + * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO + * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO + * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received + * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61 + * @retval The new state of SD FLAG (SET or RESET). + */ +#define __HAL_SD_SDIO_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__)) + +/** + * @brief Clear the SD's pending flags. + * @param __HANDLE__: SD Handle + * @param __FLAG__: specifies the flag to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) + * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received + * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61 + * @retval None + */ +#define __HAL_SD_SDIO_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__)) + +/** + * @brief Check whether the specified SD interrupt has occurred or not. + * @param __HANDLE__: SD Handle + * @param __INTERRUPT__: specifies the SDIO interrupt source to check. + * This parameter can be one of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide + * bus mode interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt + * @retval The new state of SD IT (SET or RESET). + */ +#define __HAL_SD_SDIO_GET_IT (__HANDLE__, __INTERRUPT__) __SDIO_GET_IT ((__HANDLE__)->Instance, __INTERRUPT__) + +/** + * @brief Clear the SD's interrupt pending bits. + * @param __HANDLE__ : SD Handle + * @param __INTERRUPT__: specifies the interrupt pending bit to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt + * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide + * bus mode interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 + * @retval None + */ +#define __HAL_SD_SDIO_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__)) +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + +/* Initialization/de-initialization functions **********************************/ +HAL_SD_ErrorTypedef HAL_SD_Init(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *SDCardInfo); +HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd); +__weak void HAL_SD_MspInit(SD_HandleTypeDef *hsd); +__weak void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd); + +/* I/O operation functions *****************************************************/ +/* Blocking mode: Polling */ +HAL_SD_ErrorTypedef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); +HAL_SD_ErrorTypedef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); +HAL_SD_ErrorTypedef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint64_t startaddr, uint64_t endaddr); + +/* Non-Blocking mode: Interrupt */ +void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd); + +/* Callback in non blocking modes (DMA) */ +__weak void HAL_SD_DMA_RxCpltCallback(DMA_HandleTypeDef *hdma); +__weak void HAL_SD_DMA_RxErrorCallback(DMA_HandleTypeDef *hdma); +__weak void HAL_SD_DMA_TxCpltCallback(DMA_HandleTypeDef *hdma); +__weak void HAL_SD_DMA_TxErrorCallback(DMA_HandleTypeDef *hdma); +__weak void HAL_SD_XferCpltCallback(SD_HandleTypeDef *hsd); +__weak void HAL_SD_XferErrorCallback(SD_HandleTypeDef *hsd); + +/* Non-Blocking mode: DMA */ +HAL_SD_ErrorTypedef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); +HAL_SD_ErrorTypedef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); +HAL_SD_ErrorTypedef HAL_SD_CheckWriteOperation(SD_HandleTypeDef *hsd, uint32_t Timeout); +HAL_SD_ErrorTypedef HAL_SD_CheckReadOperation(SD_HandleTypeDef *hsd, uint32_t Timeout); + +/* Peripheral Control functions ************************************************/ +HAL_SD_ErrorTypedef HAL_SD_Get_CardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *pCardInfo); +HAL_SD_ErrorTypedef HAL_SD_WideBusOperation_Config(SD_HandleTypeDef *hsd, uint32_t WideMode); +HAL_SD_ErrorTypedef HAL_SD_StopTransfer(SD_HandleTypeDef *hsd); +HAL_SD_ErrorTypedef HAL_SD_HighSpeed (SD_HandleTypeDef *hsd); + +/* Peripheral State functions **************************************************/ +HAL_SD_ErrorTypedef HAL_SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus); +HAL_SD_ErrorTypedef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypedef *pCardStatus); +HAL_SD_TransferStateTypedef HAL_SD_GetStatus(SD_HandleTypeDef *hsd); + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F4xx_HAL_SD_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/