Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
TARGET_NUCLEO_F401RE/stm32f4xx_hal_rcc_ex.h
- Committer:
- ricardobtez
- Date:
- 2016-04-05
- Revision:
- 118:16969dd821af
- Parent:
- 90:cb3d968589d8
- Child:
- 99:dbbf35b96557
File content as of revision 118:16969dd821af:
/**
******************************************************************************
* @file stm32f4xx_hal_rcc_ex.h
* @author MCD Application Team
* @version V1.1.0
* @date 19-June-2014
* @brief Header file of RCC HAL Extension module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_RCC_EX_H
#define __STM32F4xx_HAL_RCC_EX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup RCCEx
* @{
*/
/* Exported types ------------------------------------------------------------*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
/**
* @brief PLLI2S Clock structure definition
*/
typedef struct
{
uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432.
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 7.
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI1 clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
This parameter will be used only when PLLI2S is selected as Clock Source SAI */
}RCC_PLLI2SInitTypeDef;
/**
* @brief PLLSAI Clock structure definition
*/
typedef struct
{
uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432.
This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */
uint32_t PLLSAIQ; /*!< Specifies the division factor for SAI1 clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */
uint32_t PLLSAIR; /*!< specifies the division factor for LTDC clock
This parameter must be a number between Min_Data = 2 and Max_Data = 7.
This parameter will be used only when PLLSAI is selected as Clock Source LTDC */
}RCC_PLLSAIInitTypeDef;
/**
* @brief RCC extended clocks structure definition
*/
typedef struct
{
uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured.
This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */
RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters.
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
RCC_PLLSAIInitTypeDef PLLSAI; /*!< PLL SAI structure parameters.
This parameter will be used only when PLLI2S is selected as Clock Source SAI or LTDC */
uint32_t PLLI2SDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock.
This parameter must be a number between Min_Data = 1 and Max_Data = 32
This parameter will be used only when PLLI2S is selected as Clock Source SAI */
uint32_t PLLSAIDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock.
This parameter must be a number between Min_Data = 1 and Max_Data = 32
This parameter will be used only when PLLSAI is selected as Clock Source SAI */
uint32_t PLLSAIDivR; /*!< Specifies the PLLSAI division factor for LTDC clock.
This parameter must be one value of @ref RCCEx_PLLSAI_DIVR */
uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection.
This parameter can be a value of @ref RCC_RTC_Clock_Source */
uint8_t TIMPresSelection; /*!< Specifies TIM Clock Prescalers Selection.
This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
/**
* @brief PLLI2S Clock structure definition
*/
typedef struct
{
#if defined(STM32F411xE)
uint32_t PLLI2SM; /*!< PLLM: Division factor for PLLI2S VCO input clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 62 */
#endif /* STM32F411xE */
uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 7.
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
}RCC_PLLI2SInitTypeDef;
/**
* @brief RCC extended clocks structure definition
*/
typedef struct
{
uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured.
This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */
RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters.
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection.
This parameter can be a value of @ref RCC_RTC_Clock_Source */
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
/* Exported constants --------------------------------------------------------*/
/** @defgroup RCCEx_Exported_Constants
* @{
*/
/** @defgroup RCCEx_Periph_Clock_Selection
* @{
*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002)
#define RCC_PERIPHCLK_SAI_PLLSAI ((uint32_t)0x00000004)
#define RCC_PERIPHCLK_LTDC ((uint32_t)0x00000008)
#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010)
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020)
#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000002F))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000002)
#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000003))
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
/**
* @}
*/
/** @defgroup RCCEx_BitAddress_AliasRegion
* @brief RCC registers bit address in the alias region
* @{
*/
/* --- CR Register ---*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
/* Alias word address of PLLSAION bit */
#define PLLSAION_BitNumber 0x1C
#define CR_PLLSAION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (PLLSAION_BitNumber * 4))
/* --- DCKCFGR Register ---*/
/* Alias word address of TIMPRE bit */
#define RCC_DCKCFGR_OFFSET (RCC_OFFSET + 0x8C)
#define TIMPRE_BitNumber 0x18
#define DCKCFGR_TIMPRE_BB (PERIPH_BB_BASE + (RCC_DCKCFGR_OFFSET * 32) + (TIMPRE_BitNumber * 4))
/**
* @}
*/
/** @defgroup RCCEx_PLLI2S_Clock_Source
* @{
*/
#define IS_RCC_PLLI2SQ_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 15))
/**
* @}
*/
/** @defgroup RCCEx_PLLSAI_Clock_Source
* @{
*/
#define IS_RCC_PLLSAIN_VALUE(VALUE) ((192 <= (VALUE)) && ((VALUE) <= 432))
#define IS_RCC_PLLSAIQ_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 15))
#define IS_RCC_PLLSAIR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
/**
* @}
*/
/** @defgroup RCCEx_PLLSAI_DIVQ
* @{
*/
#define IS_RCC_PLLSAI_DIVQ_VALUE(VALUE) ((1 <= (VALUE)) && ((VALUE) <= 32))
/**
* @}
*/
/** @defgroup RCCEx_PLLI2S_DIVQ
* @{
*/
#define IS_RCC_PLLI2S_DIVQ_VALUE(VALUE) ((1 <= (VALUE)) && ((VALUE) <= 32))
/**
* @}
*/
/** @defgroup RCCEx_PLLSAI_DIVR
* @{
*/
#define RCC_PLLSAIDIVR_2 ((uint32_t)0x00000000)
#define RCC_PLLSAIDIVR_4 ((uint32_t)0x00010000)
#define RCC_PLLSAIDIVR_8 ((uint32_t)0x00020000)
#define RCC_PLLSAIDIVR_16 ((uint32_t)0x00030000)
#define IS_RCC_PLLSAI_DIVR_VALUE(VALUE) (((VALUE) == RCC_PLLSAIDIVR_2) ||\
((VALUE) == RCC_PLLSAIDIVR_4) ||\
((VALUE) == RCC_PLLSAIDIVR_8) ||\
((VALUE) == RCC_PLLSAIDIVR_16))
/**
* @}
*/
/** @defgroup RCCEx_SAI_BlockA_Clock_Source
* @{
*/
#define RCC_SAIACLKSOURCE_PLLSAI ((uint32_t)0x00000000)
#define RCC_SAIACLKSOURCE_PLLI2S ((uint32_t)0x00100000)
#define RCC_SAIACLKSOURCE_EXT ((uint32_t)0x00200000)
/**
* @}
*/
/** @defgroup RCCEx_SAI_BlockB_Clock_Source
* @{
*/
#define RCC_SAIBCLKSOURCE_PLLSAI ((uint32_t)0x00000000)
#define RCC_SAIBCLKSOURCE_PLLI2S ((uint32_t)0x00400000)
#define RCC_SAIBCLKSOURCE_EXT ((uint32_t)0x00800000)
/**
* @}
*/
/** @defgroup RCCEx_TIM_PRescaler_Selection
* @{
*/
#define RCC_TIMPRES_DESACTIVATED ((uint8_t)0x00)
#define RCC_TIMPRES_ACTIVATED ((uint8_t)0x01)
/**
* @}
*/
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#if defined(STM32F411xE)
/** @defgroup RCCEx_PLLI2S_PLLI2SM
* @{
*/
#define IS_RCC_PLLI2SM_VALUE(VALUE) ((VALUE) <= 63)
/**
* @}
*/
/** @defgroup RCCEx_LSE_Dual_Mode_Selection
* @{
*/
#define RCC_LSE_LOWPOWER_MODE ((uint8_t)0x00)
#define RCC_LSE_HIGHDRIVE_MODE ((uint8_t)0x01)
#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
((MODE) == RCC_LSE_HIGHDRIVE_MODE))
/**
* @}
*/
#endif /* STM32F411xE */
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/*----------------------------------- STM32F42xxx/STM32F43xxx----------------------------------*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
/** @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __GPIOI_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOIEN))
#define __GPIOF_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOFEN))
#define __GPIOG_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOGEN))
#define __GPIOJ_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOJEN))
#define __GPIOK_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOKEN))
#define __DMA2D_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_DMA2DEN))
#define __ETHMAC_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACEN))
#define __ETHMACTX_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACTXEN))
#define __ETHMACRX_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACRXEN))
#define __ETHMACPTP_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACPTPEN))
#define __USB_OTG_HS_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_OTGHSEN))
#define __USB_OTG_HS_ULPI_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_OTGHSULPIEN))
#define __GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
#define __GPIOJ_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOJEN))
#define __GPIOK_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOKEN))
#define __DMA2D_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA2DEN))
#define __ETHMAC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACEN))
#define __ETHMACTX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACTXEN))
#define __ETHMACRX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACRXEN))
#define __ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN))
#define __USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
/**
* @brief Enable ETHERNET clock.
*/
#define __ETH_CLK_ENABLE() do { \
__ETHMAC_CLK_ENABLE(); \
__ETHMACTX_CLK_ENABLE(); \
__ETHMACRX_CLK_ENABLE(); \
} while(0)
/**
* @brief Disable ETHERNET clock.
*/
#define __ETH_CLK_DISABLE() do { \
__ETHMACTX_CLK_DISABLE(); \
__ETHMACRX_CLK_DISABLE(); \
__ETHMAC_CLK_DISABLE(); \
} while(0)
/** @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __DCMI_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_DCMIEN))
#define __DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
#if defined(STM32F437xx)|| defined(STM32F439xx)
#define __CRYP_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_CRYPEN))
#define __HASH_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_HASHEN))
#define __CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
#endif /* STM32F437xx || STM32F439xx */
/** @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __FMC_CLK_ENABLE() (RCC->AHB3ENR |= (RCC_AHB3ENR_FMCEN))
#define __FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN))
/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __TIM6_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM6EN))
#define __TIM7_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM7EN))
#define __TIM12_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM12EN))
#define __TIM13_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM13EN))
#define __TIM14_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM14EN))
#define __WWDG_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_WWDGEN))
#define __USART3_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_USART3EN))
#define __UART4_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART4EN))
#define __UART5_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART5EN))
#define __CAN1_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_CAN1EN))
#define __CAN2_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_CAN2EN))
#define __DAC_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_DACEN))
#define __UART7_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART7EN))
#define __UART8_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART8EN))
#define __TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
#define __TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN))
#define __TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN))
#define __WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN))
#define __USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN))
#define __UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN))
#define __UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN))
#define __CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN))
#define __CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
#define __UART7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART7EN))
#define __UART8_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART8EN))
/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __TIM8_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_TIM8EN))
#define __ADC2_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_ADC2EN))
#define __ADC3_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_ADC3EN))
#define __SPI5_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_SPI5EN))
#define __SPI6_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_SPI6EN))
#define __SAI1_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_SAI1EN))
#define __TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
#define __ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
#define __ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
#define __SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
#define __SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN))
#define __SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
#if defined(STM32F429xx)|| defined(STM32F439xx)
#define __LTDC_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_LTDCEN))
#define __LTDC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_LTDCEN))
#endif /* STM32F429xx || STM32F439xx */
/** @brief Force or release AHB1 peripheral reset.
*/
#define __GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
#define __ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST))
#define __OTGHS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
#define __GPIOJ_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOJRST))
#define __GPIOK_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOKRST))
#define __DMA2D_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2DRST))
#define __GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
#define __ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST))
#define __OTGHS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
#define __GPIOJ_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOJRST))
#define __GPIOK_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOKRST))
#define __DMA2D_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2DRST))
/** @brief Force or release AHB2 peripheral reset.
*/
#define __DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
#define __DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
#if defined(STM32F437xx)|| defined(STM32F439xx)
#define __CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST))
#define __HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST))
#define __CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
#endif /* STM32F437xx || STM32F439xx */
/** @brief Force or release AHB3 peripheral reset
*/
#define __FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST))
#define __FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST))
/** @brief Force or release APB1 peripheral reset.
*/
#define __TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
#define __TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST))
#define __TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST))
#define __TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST))
#define __USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST))
#define __UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST))
#define __UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST))
#define __CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST))
#define __CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
#define __UART7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART7RST))
#define __UART8_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART8RST))
#define __TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
#define __TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST))
#define __TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST))
#define __USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST))
#define __UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST))
#define __UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST))
#define __CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST))
#define __CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
#define __UART7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART7RST))
#define __UART8_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART8RST))
/** @brief Force or release APB2 peripheral reset.
*/
#define __TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
#define __SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
#define __SPI6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI6RST))
#define __SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
#define __TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
#define __SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
#define __SPI6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI6RST))
#define __SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
#if defined(STM32F429xx)|| defined(STM32F439xx)
#define __LTDC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_LTDCRST))
#define __LTDC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_LTDCRST))
#endif /* STM32F429xx|| STM32F439xx */
/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
#define __SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN))
#define __ETHMAC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACLPEN))
#define __ETHMACTX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACTXLPEN))
#define __ETHMACRX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACRXLPEN))
#define __ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __OTGHS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __OTGHSULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
#define __GPIOJ_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOJLPEN))
#define __GPIOK_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOKLPEN))
#define __SRAM3_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM3LPEN))
#define __DMA2D_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2DLPEN))
#define __GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
#define __SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN))
#define __ETHMAC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACLPEN))
#define __ETHMACTX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACTXLPEN))
#define __ETHMACRX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACRXLPEN))
#define __ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __OTGHS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __OTGHSULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
#define __GPIOJ_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOJLPEN))
#define __GPIOK_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOKLPEN))
#define __DMA2D_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2DLPEN))
/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
#if defined(STM32F437xx)|| defined(STM32F439xx)
#define __CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN))
#define __HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN))
#define __CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
#endif /* STM32F437xx || STM32F439xx */
/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __FMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FMCLPEN))
#define __FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN))
/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN))
#define __TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN))
#define __TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN))
#define __TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN))
#define __TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN))
#define __USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN))
#define __UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN))
#define __UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN))
#define __CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN))
#define __CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
#define __UART7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART7LPEN))
#define __UART8_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART8LPEN))
#define __TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
#define __TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN))
#define __TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN))
#define __USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN))
#define __UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN))
#define __UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN))
#define __CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
#define __UART7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART7LPEN))
#define __UART8_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART8LPEN))
/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN))
#define __ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN))
#define __ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
#define __SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
#define __SPI6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI6LPEN))
#define __SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN))
#define __TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
#define __SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
#define __SPI6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI6LPEN))
#define __SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN))
#if defined(STM32F429xx)|| defined(STM32F439xx)
#define __LTDC_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_LTDCLPEN))
#define __LTDC_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_LTDCLPEN))
#endif /* STM32F429xx || STM32F439xx */
#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx */
/*---------------------------------------------------------------------------------------------*/
/*----------------------------------- STM32F40xxx/STM32F41xxx----------------------------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)
/** @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __GPIOI_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOIEN))
#define __GPIOF_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOFEN))
#define __GPIOG_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_GPIOGEN))
#define __USB_OTG_HS_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_OTGHSEN))
#define __USB_OTG_HS_ULPI_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_OTGHSULPIEN))
#define __GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
#define __USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
#if defined(STM32F407xx)|| defined(STM32F417xx)
/**
* @brief Enable ETHERNET clock.
*/
#define __ETHMAC_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACEN))
#define __ETHMACTX_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACTXEN))
#define __ETHMACRX_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACRXEN))
#define __ETHMACPTP_CLK_ENABLE() (RCC->AHB1ENR |= (RCC_AHB1ENR_ETHMACPTPEN))
#define __ETH_CLK_ENABLE() do { \
__ETHMAC_CLK_ENABLE(); \
__ETHMACTX_CLK_ENABLE(); \
__ETHMACRX_CLK_ENABLE(); \
} while(0)
/**
* @brief Disable ETHERNET clock.
*/
#define __ETHMAC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACEN))
#define __ETHMACTX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACTXEN))
#define __ETHMACRX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACRXEN))
#define __ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN))
#define __ETH_CLK_DISABLE() do { \
__ETHMACTX_CLK_DISABLE(); \
__ETHMACRX_CLK_DISABLE(); \
__ETHMAC_CLK_DISABLE(); \
} while(0)
#endif /* STM32F407xx || STM32F417xx */
/** @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __DCMI_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_DCMIEN))
#define __DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
#endif /* STM32F407xx || STM32F417xx */
#if defined(STM32F415xx) || defined(STM32F417xx)
#define __CRYP_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_CRYPEN))
#define __HASH_CLK_ENABLE() (RCC->AHB2ENR |= (RCC_AHB2ENR_HASHEN))
#define __CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
#endif /* STM32F415xx || STM32F417xx */
/** @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __FSMC_CLK_ENABLE() (RCC->AHB3ENR |= (RCC_AHB3ENR_FSMCEN))
#define __FSMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FSMCEN))
/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __TIM6_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM6EN))
#define __TIM7_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM7EN))
#define __TIM12_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM12EN))
#define __TIM13_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM13EN))
#define __TIM14_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_TIM14EN))
#define __WWDG_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_WWDGEN))
#define __USART3_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_USART3EN))
#define __UART4_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART4EN))
#define __UART5_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_UART5EN))
#define __CAN1_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_CAN1EN))
#define __CAN2_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_CAN2EN))
#define __DAC_CLK_ENABLE() (RCC->APB1ENR |= (RCC_APB1ENR_DACEN))
#define __TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
#define __TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN))
#define __TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN))
#define __WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN))
#define __USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN))
#define __UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN))
#define __UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN))
#define __CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN))
#define __CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
#define __TIM8_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_TIM8EN))
#define __ADC2_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_ADC2EN))
#define __ADC3_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_ADC3EN))
#define __TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
#define __ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
#define __ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
/** @brief Force or release AHB1 peripheral reset.
*/
#define __GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
#define __ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST))
#define __OTGHS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
#define __GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
#define __ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST))
#define __OTGHS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
/** @brief Force or release AHB2 peripheral reset.
*/
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
#define __DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
#endif /* STM32F407xx || STM32F417xx */
#if defined(STM32F415xx) || defined(STM32F417xx)
#define __CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST))
#define __HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST))
#define __CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
#endif /* STM32F415xx || STM32F417xx */
/** @brief Force or release AHB3 peripheral reset
*/
#define __FSMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FSMCRST))
#define __FSMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FSMCRST))
/** @brief Force or release APB1 peripheral reset.
*/
#define __TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
#define __TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST))
#define __TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST))
#define __TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST))
#define __USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST))
#define __UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST))
#define __UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST))
#define __CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST))
#define __CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
#define __TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
#define __TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST))
#define __TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST))
#define __USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST))
#define __UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST))
#define __UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST))
#define __CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST))
#define __CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
/** @brief Force or release APB2 peripheral reset.
*/
#define __TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
#define __TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
#define __SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN))
#define __ETHMAC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACLPEN))
#define __ETHMACTX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACTXLPEN))
#define __ETHMACRX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACRXLPEN))
#define __ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __OTGHS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __OTGHSULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
#define __GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
#define __SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN))
#define __ETHMAC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACLPEN))
#define __ETHMACTX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACTXLPEN))
#define __ETHMACRX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACRXLPEN))
#define __ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __OTGHS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __OTGHSULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
#endif /* STM32F407xx || STM32F417xx */
#if defined(STM32F415xx) || defined(STM32F417xx)
#define __CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN))
#define __HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN))
#define __CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
#endif /* STM32F415xx || STM32F417xx */
/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __FSMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FSMCLPEN))
#define __FSMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FSMCLPEN))
/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN))
#define __TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN))
#define __TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN))
#define __TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN))
#define __TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN))
#define __USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN))
#define __UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN))
#define __UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN))
#define __CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN))
#define __CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
#define __TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
#define __TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN))
#define __TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN))
#define __USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN))
#define __UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN))
#define __UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN))
#define __CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
*/
#define __TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN))
#define __ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN))
#define __ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
#define __TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */
/*---------------------------------------------------------------------------------------------*/
/*------------------------------------------ STM32F411xx --------------------------------------*/
#if defined(STM32F411xE)
/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
*/
#define __SPI5_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_SPI5EN))
#define __SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
/** @brief Force or release APB2 peripheral reset.
*/
#define __SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
#define __SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
*/
#define __SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
#define __SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
#endif /* STM32F411xE */
/*---------------------------------------------------------------------------------------------*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
/** @brief Macro to configure the Timers clocks prescalers
* @note This feature is only available with STM32F429x/439x Devices.
* @param __PRESC__ : specifies the Timers clocks prescalers selection
* This parameter can be one of the following values:
* @arg RCC_TIMPRES_DESACTIVATED: The Timers kernels clocks prescaler is
* equal to HPRE if PPREx is corresponding to division by 1 or 2,
* else it is equal to [(HPRE * PPREx) / 2] if PPREx is corresponding to
* division by 4 or more.
* @arg RCC_TIMPRES_ACTIVATED: The Timers kernels clocks prescaler is
* equal to HPRE if PPREx is corresponding to division by 1, 2 or 4,
* else it is equal to [(HPRE * PPREx) / 4] if PPREx is corresponding
* to division by 8 or more.
*/
#define __HAL_RCC_TIMCLKPRESCALER(__PRESC__) (*(__IO uint32_t *) DCKCFGR_TIMPRE_BB = (__PRESC__))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F411xE */
#if defined(STM32F411xE)
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
* @note This macro must be used only when the PLLI2S is disabled.
* @note PLLI2S clock source is common with the main PLL (configured in
* HAL_RCC_ClockConfig() API).
* @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 63.
* @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 2 MHz to limit PLLI2S jitter.
* @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
* on the I2S clock frequency.
*/
#define __HAL_RCC_PLLI2S_I2SCLK_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)) | (__PLLI2SM__))
#endif /* STM32F411xE */
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
/** @brief Macros to Enable or Disable the PLLISAI.
* @note The PLLSAI is only available with STM32F429x/439x Devices.
* @note The PLLSAI is disabled by hardware when entering STOP and STANDBY modes.
*/
#define __HAL_RCC_PLLSAI_ENABLE() (*(__IO uint32_t *) CR_PLLSAION_BB = ENABLE)
#define __HAL_RCC_PLLSAI_DISABLE() (*(__IO uint32_t *) CR_PLLSAION_BB = DISABLE)
/** @brief Macro to configure the PLLSAI clock multiplication and division factors.
* @note The PLLSAI is only available with STM32F429x/439x Devices.
* @note This function must be used only when the PLLSAI is disabled.
* @note PLLSAI clock source is common with the main PLL (configured in
* RCC_PLLConfig function )
* @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock.
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLSAIN parameter correctly to ensure that the VCO
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
* @param __PLLSAIQ__: specifies the division factor for SAI1 clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @param __PLLSAIR__: specifies the division factor for LTDC clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
*/
#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIN__, __PLLSAIQ__, __PLLSAIR__) (RCC->PLLSAICFGR = ((__PLLSAIN__) << 6) | ((__PLLSAIQ__) << 24) | ((__PLLSAIR__) << 28))
/** @brief Macro used by the SAI HAL driver to configure the PLLI2S clock multiplication and division factors.
* @note This macro must be used only when the PLLI2S is disabled.
* @note PLLI2S clock source is common with the main PLL (configured in
* HAL_RCC_ClockConfig() API)
* @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock.
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
* @param __PLLI2SQ__: specifies the division factor for SAI1 clock.
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @note the PLLI2SQ parameter is only available with STM32F429x/439x Devices
* and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
* on the I2S clock frequency.
*/
#define __HAL_RCC_PLLI2S_SAICLK_CONFIG(__PLLI2SN__, __PLLI2SQ__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SN__) << 6) | ((__PLLI2SQ__) << 24) | ((__PLLI2SR__) << 28))
/** @brief Macro to configure the SAI clock Divider coming from PLLI2S.
* @note The SAI peripheral is only available with STM32F429x/439x Devices.
* @note This function must be called before enabling the PLLI2S.
* @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock .
* This parameter must be a number between 1 and 32.
* SAI1 clock frequency = f(PLLI2SQ) / __PLLI2SDivQ__
*/
#define __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(__PLLI2SDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLI2SDIVQ, (__PLLI2SDivQ__)-1))
/** @brief Macro to configure the SAI clock Divider coming from PLLSAI.
* @note The SAI peripheral is only available with STM32F429x/439x Devices.
* @note This function must be called before enabling the PLLSAI.
* @param __PLLSAIDivQ__: specifies the PLLSAI division factor for SAI1 clock .
* This parameter must be a number between Min_Data = 1 and Max_Data = 32.
* SAI1 clock frequency = f(PLLSAIQ) / __PLLSAIDivQ__
*/
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(__PLLSAIDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVQ, ((__PLLSAIDivQ__)-1)<<8))
/** @brief Macro to configure the LTDC clock Divider coming from PLLSAI.
*
* @note The LTDC peripheral is only available with STM32F429x/439x Devices.
* @note This function must be called before enabling the PLLSAI.
* @param __PLLSAIDivR__: specifies the PLLSAI division factor for LTDC clock .
* This parameter must be a number between Min_Data = 2 and Max_Data = 16.
* LTDC clock frequency = f(PLLSAIR) / __PLLSAIDivR__
*/
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(__PLLSAIDivR__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVR, (__PLLSAIDivR__)))
/** @brief Macro to configure SAI1BlockA clock source selection.
* @note The SAI peripheral is only available with STM32F429x/439x Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block A clock source.
* This parameter can be one of the following values:
* @arg RCC_SAIACLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used
* as SAI1 Block A clock.
* @arg RCC_SAIACLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used
* as SAI1 Block A clock.
* @arg RCC_SAIACLKSOURCE_Ext: External clock mapped on the I2S_CKIN pin
* used as SAI1 Block A clock.
*/
#define __HAL_RCC_SAI_BLOCKACLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1ASRC, (__SOURCE__)))
/** @brief Macro to configure SAI1BlockB clock source selection.
* @note The SAI peripheral is only available with STM32F429x/439x Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block B clock source.
* This parameter can be one of the following values:
* @arg RCC_SAIBCLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used
* as SAI1 Block B clock.
* @arg RCC_SAIBCLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used
* as SAI1 Block B clock.
* @arg RCC_SAIBCLKSOURCE_Ext: External clock mapped on the I2S_CKIN pin
* used as SAI1 Block B clock.
*/
#define __HAL_RCC_SAI_BLOCKBCLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1BSRC, (__SOURCE__)))
/** @brief Enable PLLSAI_RDY interrupt.
*/
#define __HAL_RCC_PLLSAI_ENABLE_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYIE))
/** @brief Disable PLLSAI_RDY interrupt.
*/
#define __HAL_RCC_PLLSAI_DISABLE_IT() (RCC->CIR &= ~(RCC_CIR_PLLSAIRDYIE))
/** @brief Clear the PLLSAI RDY interrupt pending bits.
*/
#define __HAL_RCC_PLLSAI_CLEAR_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYF))
/** @brief Check the PLLSAI RDY interrupt has occurred or not.
* @retval The new state (TRUE or FALSE).
*/
#define __HAL_RCC_PLLSAI_GET_IT() ((RCC->CIR & (RCC_CIR_PLLSAIRDYIE)) == (RCC_CIR_PLLSAIRDYIE))
/** @brief Check PLLSAI RDY flag is set or not.
* @retval The new state (TRUE or FALSE).
*/
#define __HAL_RCC_PLLSAI_GET_FLAG() ((RCC->CR & (RCC_CR_PLLSAIRDY)) == (RCC_CR_PLLSAIRDY))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
/* Exported functions --------------------------------------------------------*/
HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit);
void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit);
#if defined(STM32F411xE)
void HAL_RCCEx_SelectLSEMode(uint8_t Mode);
#endif /* STM32F411xE */
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_RCC_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/